Experimental research on the performance of the forward variable area bypass injector for variable cycle engines

2020 ◽  
Vol 0 (0) ◽  
Author(s):  
Binglong Zhang ◽  
He Liu ◽  
Jianhua Zhou ◽  
Hui Liu
Keyword(s):  
Pressure Ratio ◽  
Effective Means ◽  
Experimental System ◽  
Area Ratio ◽  
Back Pressure ◽  
Mode Transition ◽  
Bypass Valve ◽  
Injection Coefficient ◽  
Bypass Ratio ◽  
Specific Working

Abstract The forward variable area bypass injector (FVABI) is a key component of double bypass variable cycle engine (VCE) to achieve mode transition and bypass ratio adjustment. In this paper, an experimental system for FVABI was constructed based on the analysis of relevant experimental theories, and then the experiments on FVABI were carried out for a specific working state in double bypass mode of VCE and for the comparison working states with different area ratios and different back pressure ratios. The results showed that the FVABI designed in this paper meets the requirements of VCE at this working state. The analysis of the influence of area ratio and back pressure ratio on the injection coefficient showed that the first bypass valve and back pressure were effective means to control the mass flow of FVABI.

Experimental research on the performance of the forward variable area bypass injector for variable cycle engines

2020 ◽  
Vol 0 (0) ◽  
Author(s):  
Binglong Zhang ◽  
He Liu ◽  
Jianhua Zhou ◽  
Hui Liu
Keyword(s):  
Pressure Ratio ◽  
Effective Means ◽  
Experimental System ◽  
Area Ratio ◽  
Back Pressure ◽  
Mode Transition ◽  
Bypass Valve ◽  
Injection Coefficient ◽  
Bypass Ratio ◽  
Specific Working

AbstractThe forward variable area bypass injector (FVABI) is a key component of double bypass variable cycle engine (VCE) to achieve mode transition and bypass ratio adjustment. In this paper, an experimental system for FVABI was constructed based on the analysis of relevant experimental theories, and then the experiments on FVABI were carried out for a specific working state in double bypass mode of VCE and for the comparison working states with different area ratios and different back pressure ratios. The results showed that the FVABI designed in this paper meets the requirements of VCE at this working state. The analysis of the influence of area ratio and back pressure ratio on the injection coefficient showed that the first bypass valve and back pressure were effective means to control the mass flow of FVABI.

Ultra High Bypass Ratio Engine Sizing and Cycle Selection Study for a Subsonic Commercial Aircraft in the N+2 Timeframe

2011 ◽  
Author(s):  
Brian K. Kestner ◽  
Jeff S. Schutte ◽  
Jonathan C. Gladin ◽  
Dimitri N. Mavris
Keyword(s):  
Pressure Ratio ◽  
Important Variable ◽  
Direct Drive ◽  
Commercial Aircraft ◽  
Low Pressure Turbine ◽  
Fuel Burn ◽  
Technology Transition ◽  
Fundamental Research ◽  
Bypass Ratio ◽  
Engine Cycle

This paper presents an engine sizing and cycle selection study of ultra high bypass ratio engines applied to a subsonic commercial aircraft in the N+2 (2020) timeframe. NASA has created the Environmentally Responsible Aviation (ERA) project to serve as a technology transition bridge between fundamental research (TRL 1–4) and potential users (TRL 7). Specifically, ERA is focused on subsonic transport technologies that could reach TRL 6 by 2020 and are capable of integration into an advanced vehicle concept that simultaneously meets the ERA project metrics for noise, emissions, and fuel burn. An important variable in exploring the trade space is the selection of the optimal engine cycle for use on the advanced aircraft. In this paper, two specific ultra high bypass engine cycle options will be explored: advanced direct drive and geared turbofan. The advanced direct drive turbofan is an improved version of conventional turbofans. In terms of both bypass ratio and overall pressure ratio, the advanced direct turbofan benefits from improvements in aerodynamic design of its components, as well as material stress and temperature properties. By putting a gear between the fan and the low pressure turbine, a geared turbo fan allows both components to operate at optimal speeds, thus further improving overall cycle efficiency relative to a conventional turbofan. In this study, sensitivity of cycle design with level of technology will be explored, in terms of both cycle parameters (such as specific thrust consumption (TSFC) and bypass ratio) and aircraft mission parameters (such as fuel burn and noise). To demonstrate this sensitivity, engines will be sized for optimal performance on a 300 passenger class aircraft for a 2010 level technology tube and wing airframe, a N+2 level technology tube and wing air-frame, and finally on a N+2 level technology blended wing body airframe with and without boundary layer ingestion (BLI) engines.

A New Method of Modeling Underexpanded Exhaust Plumes for Wind Tunnel Aerodynamic Testing

1989 ◽  
Vol 111 (4) ◽  
pp. 748-754
Author(s):  
V. Salemann ◽  
J. M. Williams
Keyword(s):  
Wind Tunnel ◽  
Free Stream ◽  
Dynamic Pressure ◽  
Pressure Ratio ◽  
Area Ratio ◽  
Full Scale ◽  
New Method ◽  
Thrust Coefficient ◽  
Model Scale ◽  
Exhaust Plumes

A new method for modeling hot underexpanded exhaust plumes with cold model scale plumes in aerodynamic wind tunnel testing has been developed. The method is applicable to aeropropulsion testing where significant interaction between the exhaust and the free stream and aftbody may be present. The technique scales the model and nozzle external geometry, including the nozzle exit area, matches the model jet to free-stream dynamic pressure ratio to full-scale jet to free-stream dynamic pressure ratio, and matches the model thrust coefficient to full-scale thrust coefficient. The technique does not require scaling of the internal nozzle geometry. A generalized method of characteristic computer code was used to predict the plume shapes of a hot (γ = 1.2) half-scale nozzle of area ratio 3.2 and of a cold (γ = 1.4) model scale nozzle of area ratio 1.3, whose pressure ratio and area ratio were selected to satisfy the above criteria and other testing requirements. The plume shapes showed good agreement. Code validity was checked by comparing code results for cold air exhausting into a quiescent atmosphere to pilot surveys and shadowgraphs of model nozzle plumes taken in a static facility.

Effect of Cavities in Suddenly Expanded Flow at Supersonic Mach Number

CFD letters ◽  
2021 ◽  
Vol 13 (9) ◽  
pp. 57-71
Author(s):  
Atifatul Ismah Ismail
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Mach Number ◽  
Pressure Ratio ◽  
Area Ratio ◽  
Base Pressure ◽  
Sudden Expansion ◽  
Expansion Level ◽  
Computational Fluid Dynamics Cfd ◽  
Base Drag

The contribution from the base drag due to the sub-atmospheric pressure is significant. It can be more than two-thirds of the net drag. There is a need to increase the base pressure and hence decrease the base drag. This research examines the effect of Mach Number on base pressure. To accomplish this objective, it controls the efficacy in an enlarged duct computed by the numerical approach using Computational Fluid Dynamics (CFD) Analysis. This experiment was carried out by considering the expansion level and the aspect cavity ratio. The computational fluid dynamics method is used to model supersonic motion with the sudden expansion, and a convergent-divergent nozzle is used. The Mach number is 1.74 for the present study, and the area ratio is 2.56. The L/D ratio varied from 2, 4, 6, 8, and 10, and the simulated nozzle pressure ratio ranged from 3 to 11. The two-dimensional planar design used commercial software from ANSYS. The airflow from a Mach 1.74 convergent-divergent axi-symmetric nozzle expanded suddenly into circular ducts of diameters 17 and 24.5 mm with and without annular rectangular cavities. The diameter of the duct is taken D=17mm and D=24.5mm. The C-D nozzle was developed and modeled in the present study: K-ε standard wall function turbulence model was used with the commercial computational fluid dynamics (CFD) and validated. The result indicates that the base pressure is impacted by the expansion level, the enlarged duct size, and the passage’s area ratio.

Remote Experiments in Freshman Engineering Education by Integrated e-Learning

2012 ◽  
pp. 60-83 ◽  
Author(s):  
Miroslava Ožvoldová ◽  
Franz Schauer
Keyword(s):  
Data Transfer ◽  
Effective Means ◽  
Experimental System ◽  
Free Fall ◽  
The Internet ◽  
Remote Laboratory ◽  
Physics Courses ◽  
L System ◽  
E Learning ◽  
Web Control

In this chapter, we present the outlines of the remote laboratory integrated in the INTe-L system, using the Internet School Experimental System (ISES) as hardware and an ISES WEB Control kit as software. We suggest an architecture for implementing remote laboratories, with data transfer across the Internet, based on standard and reusable ISES modules as hardware and Java supported ISES software. The Learning Management System (LMS) MOODLE turns out to be a highly effective means of organization of physics courses. The first experience on teaching units Free fall (http://remotelab4.truni.sk), Simple Pendulum (http://remotelab5.truni.sk), and Natural and driven oscillations (www.ises.info – see Remote laboratory) is presented.

Enhancement of pollutants hydrocyclone separation by adjusting back pressure ratio and pressure drop ratio

2020 ◽  
Vol 240 ◽  
pp. 116604 ◽  
Author(s):  
Jinyi Tian ◽  
Hualin Wang ◽  
Wenjie Lv ◽  
Yuan Huang ◽  
Pengbo Fu ◽  
...  
Keyword(s):  
Pressure Drop ◽  
Pressure Ratio ◽  
Back Pressure

The Influence of Fan Root Flow on the Aerodynamics of a Low-Pressure Compressor Transition Duct

2019 ◽  
Author(s):  
A. D. Walker ◽  
I. Mariah ◽  
D. Tsakmakidou ◽  
H. Vadhvana ◽  
C. Hall
Keyword(s):  
Gas Turbines ◽  
Pressure Ratio ◽  
Axial Compressor ◽  
Pressure Profile ◽  
Low Pressure ◽  
Secondary Flows ◽  
Test Facility ◽  
Inlet Flow ◽  
Flat Profile ◽  
Bypass Ratio

Abstract To reduce fuel-burn and CO2 emissions from aero gas turbines there is a drive towards very-high bypass ratio and smaller ultra-high-pressure ratio core engine technologies. However, this makes the design of the ducts connecting various compressor spools more challenging as the higher required radius change increases their aerodynamic loading. This is exacerbated for the duct which feeds the engine core as it must accept the relatively low-quality flow produced by the fan root. This is characterised by a hub-low pressure profile and large secondary flow structures which will inevitably increase loss and the likelihood of flow separation. Additionally, the desire for shorter, lighter nacelles means that the engine intake may be unable provide a uniform inlet flow to the fan when the aircraft is at an angle of attack or subject to cross winds. Any inlet distortion this generates can also further degrade the quality of the flow entering the core of the engine. This paper uses a combination of experiments and CFD to examine the effects of the inlet flow on the aerodynamics of an engine section splitter and transition duct designed to feed the low-pressure spool of a high bypass ratio turbofan. A fully annular test facility incorporating a 1½ stage axial compressor was used to compare the system performance of a rotor that produced a nominally flat profile with one that had a notably hub deficient flow. A RANS CFD model, employing a mixing plane between the rotor and Engine Section Stator (ESS) and a Reynolds Stress turbulence model, was then validated and used to further investigate the effects of increased inlet boundary layer thickness and bulk swirl distortion at rotor inlet. Overall, changes to the inlet condition were seen to have a surprisingly small effect on the flow at duct exit — i.e. the flow presented to the downstream compressor. Changes to the inlet did, however, generate increased secondary flows and degrade the performance of the ESS. This resulted in notably increased total pressure loss; in excess of 12% for the hub-low inlet and in excess of 30% at high inlet swirl where the flow in the ESS separated. However, the increased ESS wake structures, and the enhanced mixing, delayed separation in the duct suggesting that, overall the design was reasonably robust, albeit with a significant penalty in system loss.

Analyses and Optimization of a Propulsion Cycle for Unmixed High Bypass Turbofan

2008 ◽  
Author(s):  
Adel Ghenaiet
Keyword(s):  
Fuel Consumption ◽  
Pressure Ratio ◽  
Specific Fuel Consumption ◽  
Design Parameters ◽  
Inlet Temperature ◽  
Turbine Inlet Temperature ◽  
High Pressure Ratio ◽  
Turbine Inlet ◽  
Design Variables ◽  
Bypass Ratio

This paper deals with a parametric study and an optimization for the design variables of a high bypass unmixed turbofan equipping commercial aircrafts. The objective of the first part of this study is to highlight the effects of the principal design parameters (bypass ratio, compression ratios, turbine inlet temperature etc..) on the uninstalled performance, in terms of specific thrust and specific fuel consumption. The second part concerns the optimization, aiming at finding the optimum design parameters concurrently minimizing the specific fuel consumption at cruise, and meeting the thrust requirement at takeoff. The cycle analyzer (on-design and off-design) as coupled to the optimization algorithm MMFD by adopting a random multi-starts search strategy is shown to be stable and converging. The predefined requirements and constraints have dictated utilizing an engine with a high-bypass ratio, high-pressure ratio and a moderate turbine inlet temperature. In general, the obtained results compare fairly well with typical data available for an equivalent ‘reference’ engine. This elaborated methodology is shown to be consistent with the conceptual design requirements and accuracy, because, it does not use components’ characteristics, and operates on simplifying assumptions. This present methodology can be readily adapted for other configurations of aero-engines as well, and easily integrated in a multi-disciplinary design approach.

Fundamental Differences Between Conventional and Geared Turbofans

2009 ◽  
Author(s):  
Joachim Kurzke
Keyword(s):  
Fuel Consumption ◽  
Real Option ◽  
Pressure Ratio ◽  
Thermodynamic Cycle ◽  
Specific Fuel Consumption ◽  
Thermodynamic Efficiency ◽  
Aircraft Engines ◽  
Direct Drive ◽  
Significant Difference ◽  
Bypass Ratio

The potential for improving the thermodynamic efficiency of aircraft engines is limited because the aerodynamic quality of the turbomachines has already achieved a very high level. While in the past increasing burner exit temperature did contribute to better cycle efficiency, this is no longer the case with today’s temperatures in the range of 1900...2000K. Increasing the cycle pressure ratio above 40 will yield only a small fuel consumption benefit. Therefore the only way to improve the fuel efficiency of aircraft engines significantly is to increase bypass ratio — which yields higher propulsive efficiency. A purely thermodynamic cycle study shows that specific fuel consumption decreases continuously with increasing bypass ratio. However, thermodynamics alone is a too simplistic view of the problem. A conventional direct drive turbofan of bypass ratio 6 looks very different to an engine with bypass ratio 10. Increasing bypass ratio above 10 makes it attractive to design an engine with a gearbox to separate the fan speed from the other low pressure components. Different rules apply for optimizing turbofans of conventional designs and those with a gearbox. This paper describes various criteria to be considered for optimizing the respective engines and their components. For illustrating the main differences between conventional and geared turbofans it is assumed that an existing core of medium pressure ratio with a two stage high pressure turbine is to be used. The design of the engines is done for takeoff rating because this is the mechanically most challenging condition. For each engine the flow annulus is examined and stress calculations for the disks are performed. The result of the integrated aero-thermodynamic and mechanical study allows a comparison of the fundamental differences between conventional and geared turbofans. At the same bypass ratio there will be no significant difference in specific fuel consumption between the alternative designs. The main difference is in the parts count which is much lower for the geared turbofan than for the conventional engine. However, these parts will be mechanically much more challenging than those of a conventional turbofan. If the bypass ratio is increased significantly above 10, then the geared turbofan becomes more and more attractive and the conventional turbofan design is no longer a real option. The maximum practical bypass ratio for ducted fans depends on the nacelle drag and how the installation problems can be solved.

Dual-Stage Turbocharger Matching and Boost Control Options

2008 ◽  
Author(s):  
Byungchan Lee ◽  
Dohoy Jung ◽  
Dennis Assanis ◽  
Zoran Filipi
Keyword(s):  
High Pressure ◽  
Diesel Engines ◽  
Pressure Ratio ◽  
Boost Pressure ◽  
High Pressure Turbine ◽  
Multi Stage ◽  
Bypass Valve ◽  
Dual Stage ◽  
Engine System ◽  
The Impact

Diesel engines are gaining in popularity, penetrating even the luxury and sports vehicle segments that have traditionally been strongly favored gasoline engines as the performance and refinement of diesel engines have improved significantly in recent years. The introduction of sophisticated technologies such as common rail injection (CRI), advanced boosting systems such as variable geometry and multi-stage turbocharging, and exhaust gas after-treatment systems have renewed the interest in Diesel engines. Among the technical advancements of diesel engines, the multi-stage turbocharging is the key to achieve such high power density that is suitable for the luxury and sports vehicle applications. Single-stage turbocharging is limited to roughly 2.5 bar of boost pressure. In order to raise the boost pressure up to levels of 4 bar or so, another turbocharger must be connected in series further multiplying the pressure ratio. The dual-stage turbocharging, however, adds system complexity, and the matching of two turbochargers becomes very costly if it is to be done experimentally. This study presents a simulation-based methodology for dual-stage turbocharger matching through an iterative procedure predicting optimal configurations of compressors and turbines. A physics-based zero-dimensional Diesel engine system simulation with a dual-stage turbocharger is implemented in SIMULINK environment, allowing easy evaluation of different configurations and subsequent analysis of engine system performance. The simulation program is augmented with a turbocharger matching program and a turbomachinery scaling routine. The configurations considered in the study include a dual-stage turbocharging system with a bypass valve added to the high pressure turbine, and a system with a wastegate valve added to a low-pressure turbine. The systematic simulation study allows detailed analysis of the impact of each of the configurations on matching, boost characteristics and transient response. The configuration with the bypass valve across high pressure turbine showed better results in terms of both steady state engine torque and transient behavior.

Sign in / Sign up

Export Citation Format

Share Document