scholarly journals Effects of three-layer structure and age on mechanical properties of moso bamboo

BioResources ◽  
2021 ◽  
Vol 16 (2) ◽  
pp. 2406-2415
Author(s):  
Ge Han ◽  
Rongrong Li ◽  
Chuangui Wang
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Flexural Strength ◽  
Outer Layer ◽  
Layer Structure ◽  
Moso Bamboo ◽  
Modulus Of Rupture ◽  
Negative Effects ◽  
The Relationship ◽  
Important Basis

The effects of a three-layer structure and age on the mechanical properties of moso bamboo were investigated. The ages of 1-, 3-, and 5-year-old bamboo were chosen to make test samples, and specimens from each age of moso bamboo were divided into three groups (raw bamboo, bamboo removed from outer layer, and bamboo removed from inner layer) for evaluation of modulus of rupture and parallel-to-grain compressive strength. The regression analysis was completed to evaluate the relationship between mechanical properties and bamboo age. The results showed that the age of moso bamboo was positively correlated with the flexural and parallel-to-grain compressive strengths. The mechanical strength of moso bamboo increased with the increased age of moso bamboo. For the moso bamboo with same age, the flexural and parallel-to-grain compressive strengths decreased for the samples without bamboo outer layer. However, for the samples without bamboo inner layer, the parallel-to-grain compressive strength remained unchanged, but the flexural strength increased. The outer layer of bamboo with high toughness and flexibility played an important role during bending. However, the inner layer of bamboo is relatively brittle, which has negative effects on its flexural strength. These results provide an important basis for the bamboo used in engineering.

scholarly journals Incorporation of Chitosan Nanoparticles into a Cold-Cure Orthodontic Acrylic Resin: Effects on Mechanical Properties

Biomimetics ◽  
2021 ◽  
Vol 6 (1) ◽  
pp. 7
Author(s):  
Mostafa Shahabi ◽  
Sorour Movahedi Fazel ◽  
Abdolrasoul Rangrazi
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Impact Strength ◽  
Flexural Strength ◽  
Chitosan Nanoparticles ◽  
Antimicrobial Properties ◽  
Acrylic Resin ◽  
Orthodontic Appliances ◽  
Negative Effects ◽  
Acrylic Resins

Improvement of the antibacterial properties of acrylic resins, used in the construction of removable orthodontic appliances, is an important strategy to reduce the incidence of caries and oral diseases in orthodontic treatments. The addition of antimicrobial agents to acrylic resins is one of the effective methods to enhance the antimicrobial properties of these materials. However, one main concern is that modification of acrylic resin has negative effects on its mechanical properties. Recently, chitosan nanoparticles (NPs), as biocompatible and biodegradable polysaccharides with remarkable antimicrobial properties, have been used in different areas of dentistry and medicine. This study aimed to investigate the effects of adding chitosan NPs on the mechanical properties of a cold-cure orthodontic acrylic resin. The chitosan NPs were added to the acrylic resin in various weight percentages: 0% (control), 0.5%, 1%, 2%, and 4%. The flexural strength, compressive strength, Vickers microhardness, and impact strength measurements were performed for all five groups. The results showed that adding up to 1% (w/w) chitosan NPs to an acrylic resin had no significant negative effects on its flexural strength and compressive strength, while it decreased these parameters at weight percentages of 2% and 4% (w/w). The results also revealed that modification of acrylic resin with chitosan NPs up to 4% had no significant negative effects on the microhardness and impact strength of acrylic resin. In conclusion, the addition of chitosan NPs up to 1% (w/w) had no significant negative effects on the mechanical properties of cold-cure acrylic resin.

scholarly journals Preparation of Electric- and Magnetic-Activated Water and Its Influence on the Workability and Mechanical Properties of Cement Mortar

2021 ◽  
Vol 13 (8) ◽  
pp. 4546
Author(s):  
Kaiyue Zhao ◽  
Peng Zhang ◽  
Bing Wang ◽  
Yupeng Tian ◽  
Shanbin Xue ◽  
...  
Keyword(s):  
Magnetic Field ◽  
Mechanical Properties ◽  
Compressive Strength ◽  
Flexural Strength ◽  
Cement Paste ◽  
Cement Mortar ◽  
Environmental Issues ◽  
Chemical Admixtures ◽  
Untreated Water ◽  
Alternating Voltage

Cement-based materials prepared with activated water induced by a magnetic field or electric field represent a possible solution to environmental issues caused by the worldwide utilization of chemical admixtures. In this contribution, electric- and magnetic-activated water have been produced. The workability and mechanical properties of cement mortar prepared with this activated water have been investigated. The results indicate that the pH and absorbance (Abs) values of the water varied as the electric and magnetic field changed, and their values increased significantly, exhibiting improved activity compared with that of the untreated water. In addition, activated water still retains activity within 30 min of the resting time. The fluidity of the cement paste prepared with electric-activated water was significantly larger than that of the untreated paste. However, the level of improvement differed with the worst performance resulting from cement paste prepared with alternating voltage activated water. In terms of mechanical properties, both compressive strength and flexural strength obtained its maximum values at 280 mT with two processing cycles. The compressive strength increased 26% as the curing time increased from 7 days to 28 days and flexural strength increased by 31%. In addition, through the introduction of magnetic-activated water into cement mortar, the mechanical strength can be maintained without losing its workability when the amount of cement is reduced.

scholarly journals Assessment of the Rheological and Mechanical Properties of Geopolymer Concrete Comprising Fly Ash and Fluid Catalytic Cracking Residue as Aluminosilicate Precursor

2021 ◽  
Vol 11 (7) ◽  
pp. 3032
Author(s):  
Tuan Anh Le ◽  
Sinh Hoang Le ◽  
Thuy Ninh Nguyen ◽  
Khoa Tan Nguyen
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Elastic Modulus ◽  
Fly Ash ◽  
Flexural Strength ◽  
Catalytic Cracking ◽  
Fluid Catalytic Cracking ◽  
High Alumina ◽  
Geopolymer Concrete ◽  
Sem Images

The use of fluid catalytic cracking (FCC) by-products as aluminosilicate precursors in geopolymer binders has attracted significant interest from researchers in recent years owing to their high alumina and silica contents. Introduced in this study is the use of geopolymer concrete comprising FCC residue combined with fly ash as the requisite source of aluminosilicate. Fly ash was replaced with various FCC residue contents ranging from 0–100% by mass of binder. Results from standard testing methods showed that geopolymer concrete rheological properties such as yield stress and plastic viscosity as well as mechanical properties including compressive strength, flexural strength, and elastic modulus were affected significantly by the FCC residue content. With alkali liquid to geopolymer solid ratios (AL:GS) of 0.4 and 0.5, a reduction in compressive and flexural strength was observed in the case of geopolymer concrete with increasing FCC residue content. On the contrary, geopolymer concrete with increasing FCC residue content exhibited improved strength with an AL:GS ratio of 0.65. Relationships enabling estimation of geopolymer elastic modulus based on compressive strength were investigated. Scanning electron microscope (SEM) images and X-ray diffraction (XRD) patterns revealed that the final product from the geopolymerization process consisting of FCC residue was similar to fly ash-based geopolymer concrete. These observations highlight the potential of FCC residue as an aluminosilicate source for geopolymer products.

scholarly journals Properties of High-Strength Flowable Mortar Reinforced with Palm Fibers

2012 ◽  
Vol 2012 ◽  
pp. 1-5 ◽  
Author(s):  
Eethar Thanon Dawood ◽  
Mahyuddin Ramli
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Flexural Strength ◽  
Physical And Mechanical Properties ◽  
High Strength ◽  
Test Results ◽  
Palm Fiber ◽  
Toughness Index ◽  
Strength And Toughness

This study was conducted to determine some physical and mechanical properties of high-strength flowable mortar reinforced with different percentages of palm fiber (0, 0.2, 0.4, 0.6, 0.8, 1.0, 1.2, 1.4, and 1.6% as volumetric fractions). The density, compressive strength, flexural strength, and toughness index were tested to determine the mechanical properties of this mortar. Test results illustrate that the inclusion of this fiber reduces the density of mortar. The use of 0.6% of palm fiber increases the compressive strength and flexural strength by about 15.1%, and 16%, respectively; besides, the toughness index (I5) of the high-strength flowable mortar has been significantly enhanced by the use of 1% and more of palm fiber.

Size Effect on Mechanical Properties of LVL

2014 ◽  
Vol 887-888 ◽  
pp. 824-829
Author(s):  
Qing Fang Lv ◽  
Ji Hong Qin ◽  
Ran Zhu
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Size Effect ◽  
Tensile Test ◽  
Compression Test ◽  
Test Results ◽  
Laminated Veneer Lumber ◽  
Object Of Study ◽  
The Relationship

Laminated veneer lumber is taken as an object of study, and use LVL specimens of different sizes for compression test and tensile test. The goal of the experiment is to investigate the size effect on compressive strength and tensile strength as well as the influence of the secondary glued laminated face, which appears in the secondary molding processes. The results show that both compressive strength and tensile strength have the size effect apparently and the existence of the secondary glued laminated face lower the compressive strength of LVL specimens. Afterwards, the relationship between compressive strength and volume along with tensile strength and area are obtained by the test results.

Development of Nanocement Mortar as a Construction Material

2013 ◽  
Vol 795 ◽  
pp. 684-691 ◽  
Author(s):  
Wail N. Al-Rifaie ◽  
Omar Mohanad Mahdi ◽  
Waleed Khalil Ahmed
Keyword(s):  
Compressive Strength ◽  
Flexural Strength ◽  
Cement Mortar ◽  
Construction Material ◽  
Modulus Of Rupture ◽  
Early Stages

The present research examined the compressive and flexural strength of nanocement mortar by using micro cement, micro sand, nanosilica and nanoclay in developing a nanocement mortar which can lead to improvements in ferrocement construction. The measured results demonstrate the increase in compressive and flexural strength of mortars at early stages of hardening. In addition, the influence of heating on compressive strength of cement mortar. General expressions to predict the compressive strength, modulus of rupture for the developed nanocement mortar in the present work are proposed.

Research on Mechanical Properties of Crumb Rubber Concrete

2011 ◽  
Vol 477 ◽  
pp. 290-295 ◽  
Author(s):  
Li Bo Bian ◽  
Shao Min Song
Keyword(s):  
Mechanical Properties ◽  
Wear Resistance ◽  
Compressive Strength ◽  
Flexural Strength ◽  
Apparent Density ◽  
Crumb Rubber ◽  
Fatigue Performance ◽  
Brittleness Index ◽  
Mixing Ratio ◽  
Rubber Concrete

Considering large number production of the abandoned tyres and the question of the concrete with mixture of crumb rubber，the mainly task of this paper is to study the mechanical properties of different mixing ratio concrete with vary volume of crumb rubber. The results showed that the workability, apparent density, compressive strength, flexural strength and brittleness index decrease as the increase of crumb rubber. While the anti-crack performance and anti-fatigue performance can be improved. The wear-resistance properties are a little lower than common concrete.

Effect of using magnetic water on the mechanical properties of concrete exposed to elevated temperature

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Wasim Barham ◽  
Ammar AL-Maabreh ◽  
Omar Latayfeh
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Elevated Temperature ◽  
Flexural Strength ◽  
Tap Water ◽  
Splitting Tensile Strength ◽  
Content Type ◽  
Normal Water ◽  
Magnetic Water

PurposeThe influence of using magnetic water instead of tap water in the mechanical properties of the concrete exposed to elevated temperatures was investigated. Two concrete mixes were used and cast with the same ingredients. Tap water was used in the first mix and magnetic water was used in the second mix. A total of 48 specimens were cast and divided as follows: 16 cylinders for the concrete compressive strength test (8 samples for each mix), 16 cylinders for the splitting tensile strength (8 specimens for each mix) and 16 beams to test the influences of magnetized water on the flexural strength of concrete (8 specimens for each mixture). Specimens were exposed to temperatures of (25 °C, 200 °C, 400 °C and 600 °C). The experimental results showed that magnetic water highly affected the mechanical properties of concrete. Specimens cast and curried out with magnetic water show higher compressive strength, splitting tensile strength and flexural strength compared to normal water specimens at all temperatures. The relative strength range between the two types of water used was 110–123% for compressive strength and 110–133% for splitting strength. For the center point loading test, the relative flexural strength range was 118–140%. The use of magnetic water in mixing concrete contribute to a more complete hydration process.Design/methodology/approachExperimental study was carried out on two concrete mixes to investigate the effect of magnetic water. Mix#1 used normal water as the mixing water, and Mix#2 used magnetic water instead of normal water. After 28 days, all the samples were taken out of the tank and left to dry for seven days, then they were divided into different groups. Each group was exposed to a different temperature where it was placed in a large oven for two hours. Three different tests were carried out on the samples, these tests were concrete compressive strength, flexural strength and splitting tensile strength.FindingsExposure of concrete to high temperatures had a significant influence on concrete mechanical properties. Specimens prepared using magnetic water showed higher compressive strength at all temperature levels. The use of magnetic water in casting and curing concrete can increase the compressive strength by 23%. Specimens prepared using magnetic water show higher splitting tensile strength at all temperatures up to 33%. The use of magnetic water in casting and curing can strengthen and increase concrete resistance to high temperatures, a significant enhancement in flexural strength at all temperatures was found with a value up to 40%.Originality/valuePrevious research proved the advantages of using magnetic water for improving the mechanical properties of concrete under normal conditions. The potential of using magnetic water in the concrete industry in the future requires conducting extensive research to study the behavior of magnetized concrete under severe conditions to which concrete structures may be subjected to. These days, there are attempts to obtain stronger concrete with high resistance to harsh environmental conditions without adding new costly ingredients to its main mixture. No research has been carried out to investigate the effect of magnetic water on the mechanical properties of concrete exposed to elevated temperature. The main objective of this study is to evaluate the effect of using magnetic water on the mechanical properties of hardened concrete subjected to elevated temperature.

scholarly journals The Mechanical Properties of Steel-Polypropylene Fibre Composites Concrete (HyFRCC)

2015 ◽  
Vol 773-774 ◽  
pp. 949-953 ◽  
Author(s):  
Izni Syahrizal Ibrahim ◽  
Wan Amizah Wan Jusoh ◽  
Abdul Rahman Mohd Sam ◽  
Nur Ain Mustapa ◽  
Sk Muiz Sk Abdul Razak
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Flexural Strength ◽  
Volume Fraction ◽  
Concrete Strength ◽  
Fibre Volume Fraction ◽  
Fibre Volume ◽  
Polypropylene Fibre ◽  
Experimental Results

This paper discusses the experimental results on the mechanical properties of hybrid fibre reinforced composite concrete (HyFRCC) containing different proportions of steel fibre (SF) and polypropylene fibre (PPF). The mechanical properties include compressive strength, tensile strength, and flexural strength. SF is known to enhance the flexural and tensile strengths, and at the same time is able to resist the formation of macro cracking. Meanwhile, PPF contributes to the tensile strain capacity and compressive strength, and also delay the formation of micro cracks. Hooked-end deformed type SF fibre with 60 mm length and fibrillated virgin type PPF fibre with 19 mm length are used in this study. Meanwhile, the concrete strength is maintained for grade C30. The percentage proportion of SF-PPF fibres are varied in the range of 100-0%, 75-25%, 50-50%, 25-75% and 0-100% of which the total fibre volume fraction (Vf) is fixed at 0.5%. The experimental results reveal that the percentage proportion of SF-PPF fibres with 75-25% produced the maximum performance of flexural strength, tensile strength and flexural toughness. Meanwhile, the percentage proportion of SF-PPF fibres with 100-0% contributes to the improvement of the compressive strength compared to that of plain concrete.

scholarly journals AN INVESTIGATION ON THE EFFECTS OF MICRO-PARAMETERS ON THE STRENGTH PROPERTIES OF ROCK

2021 ◽  
Vol 36 (1) ◽  
pp. 111-119
Author(s):  
Behzad Jafari Mohammadabadi ◽  
Kourosh Shahriar ◽  
Hossein Jalalifar ◽  
Kaveh Ahangari
Keyword(s):  
Mechanical Properties ◽  
Numerical Simulation ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Friction Coefficient ◽  
Critical Stress ◽  
Friction Angle ◽  
Strength Properties ◽  
Brazilian Tensile Strength ◽  
The Relationship

Rocks are formed from particles and the interaction between those particles controls the behaviour of a rock’s mechanical properties. Since it is very important to conduct extensive studies about the relationship between the micro-parameters and macro-parameters of rock, this paper investigates the effects of some micro-parameters on strength properties and the behaviour of cracks in rock. This is carried out by using numerical simulation of an extensive series of Uniaxial Compressive Strength (UCS) and Brazilian Tensile Strength (BTS) tests. The micro-parameters included the particles’ contact modulus, the contact stiff ness ratio, bond cohesion, bond tensile strength, the friction coefficient and the friction angle, and the mechanical properties of chromite rock have been considered as base values of the investigation. Based on the obtained results, it was found that the most important micro-parameters on the behaviour of rock in the compressive state are bond cohesion, bond tensile strength, and the friction coefficient. Also, the bond tensile strength showed the largest effect under tensile conditions. The micro-parameter of bond tensile strength increased the rock tensile strength (up to 5 times), minimized destructive cracks and increased the corresponding strain (almost 2.5 times) during critical stress.

Sign in / Sign up

Export Citation Format

Share Document