Microstructure and Hall–Petch Behavior of Fe–Co-based Hiperco© Alloys

2000 ◽  
Vol 15 (4) ◽  
pp. 835-837 ◽  
Author(s):  
Chang-He Shang ◽  
R. C. Cammarata ◽  
T. P. Weihs ◽  
C. L. Chien
Keyword(s):  
Electron Microscopy ◽  
Grain Size ◽  
Alloy Composition ◽  
Volume Fraction ◽  
Second Phase ◽  
Boundary Mobility ◽  
Grain Boundary Mobility ◽  
Nb Content ◽  
Cold Rolled ◽  
Scanning Electron

The microstructure and hardness of Fe–Co-based Hiperco© alloys were investigated. Scanning electron microscopy revealed elongated grains in the as-received (cast and cold-rolled) alloys, and samples containing Nb had second phase precipitates. Annealing of alloys for 1 to 3 h at temperatures in the range 700 to 800 °C resulted in grains becoming equiaxed. In the Nb-containing alloys, the original precipitates dissolved and new precipitates appeared. The rate of grain growth decreased with increasing Nb content, suggesting that Nb or Nb-containing precipitates were responsible for a reduction in the grain boundary mobility. The hardness as a function of grain size in the annealed samples of all of the alloys could be plotted on the same Hall–Petch curve, indicating that the yield strength of these alloys is governed by the grain size, independent of the alloy composition and volume fraction of precipitates.

Effects of Rare Earth on Microstructure and Mechanical Properties of Al-3.2Mg Alloy

2015 ◽  
Vol 817 ◽  
pp. 192-197
Author(s):  
Xin Zhang ◽  
Ze Hua Wang ◽  
Ze Hua Zhou ◽  
Jian Ming Xu ◽  
Zhao Jun Zhong ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Scanning Electron Microscopy ◽  
Grain Size ◽  
Tensile Strength ◽  
Rare Earth ◽  
Second Phase ◽  
Phase Precipitation ◽  
X Ray ◽  
Scanning Electron

A series of Al-3.2Mg alloys with addition of 0~1.6 wt.% rare earth (Ce and La) were prepared. The microstructure of as-cast Al-3.2Mg alloys was investigated by optical microscopy (OM), scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS), and the tensile strength was measured. The results indicated that the addition of rare earth elements refined grain size and secondary dendrite arm spacing (SDAS), and the tensile strength was affected by means of the second-phase precipitation and the grain boundary. Accordingly, the ductility of Al-3.2Mg alloys reduced with the increasing of RE addition due to the more second-phase formation.

Effect of Vanadium and Niobium on the Microstructure of Carbide Reinforced Indefinite Chilled Cast Rolls

2011 ◽  
Vol 311-313 ◽  
pp. 864-870
Author(s):  
Gen Zhe Huang ◽  
Zeng Hui Li
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Optical Microscopy ◽  
Critical Point ◽  
Volume Fraction ◽  
Microstructural Analysis ◽  
Energy Dispersive ◽  
X Ray ◽  
Nb Content ◽  
Scanning Electron

In the present work, effects of elements vanadium and niobium on the microstructure of the conventional indefinite chilled rolls made by small vertical centrifugal caster were investigated, using optical microscopy, Scanning Electron Microscopy (SEM, Jeol 6400), Energy Dispersive X-ray Spectroscopy (EDXS, Cu-K radiation) to identify the type, morphology, and to measure the volume fraction and the distribution of carbides and graphites formed during solidification. Microstructural analysis indicates that, the amount of graphite is dramatically reduced by adding V element. The volume fraction of the square-like carbides NbC increases with the Nb content increasing. However, if Nb content is over a critical point, large amount of the square-like NbC carbide can be seriously segregated in the out part of the section.

scholarly journals The Formation of 14H-LPSO in Mg–9Gd–2Y–2Zn–0.5Zr Alloy during Heat Treatment

Materials ◽  
2021 ◽  
Vol 14 (19) ◽  
pp. 5758
Author(s):  
Yunfang Liu ◽  
Yaqin Yang ◽  
Ming Yi ◽  
Jianmin Yu ◽  
Baocheng Li ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Heat Treatment ◽  
Grain Size ◽  
Volume Fraction ◽  
Cast Alloy ◽  
Solution Treatment ◽  
Phase Changes ◽  
Solution Temperature ◽  
Second Phase ◽  
Lpso Phase

There is a new long-period stacking ordered structure in Mg–RE–Zn magnesium alloys, namely the LPSO phase, which can effectively improve the yield strength, elongation, and corrosion resistance of Mg alloys. According to different types of Mg–RE–Zn alloy systems, two transformation modes are involved in the heat treatment transformation process. The first is the alloy without LPSO phase in the as-cast alloy, and the MgxRE phase changes to 14H-LPSO phase. The second is the alloy containing LPSO phase in the as-cast state, and the 14H-LPSO phase is obtained by the transformations of 6H, 18R, and 24R. The effects of different solution parameters on the second phase of Mg–9Gd–2Y–2Zn–0.5Zr alloy were studied by scanning electron microscopy (SEM), transmission electron microscopy (TEM), and X-ray diffraction (XRD). The precipitation mechanism of 14H-LPSO phase during solution treatment was further clarified. At a solution time of 13 h, the grain size increased rapidly initially and then decreased slightly with increasing solution temperature. The analysis of the volume fraction of the second phase and lattice constant showed that Gd and Y elements in the alloy precipitated from the matrix and formed 14H-LPSO phase after solution treatment at 490 °C for 13 h. At this time, the hardness of the alloy reached the maximum of 74.6 HV. After solution treatment at 500 °C for 13 h, the solid solution degree of the alloy increases, and the grain size and hardness of the alloy remain basically unchanged.

Grain Refinement in Titanium-Erbium Alloys

1974 ◽  
Vol 32 ◽  
pp. 522-523
Author(s):  
B. B. Rath ◽  
J. E. O'Neal ◽  
R. J. Lederich
Keyword(s):  
Electron Microscopy ◽  
Size Distribution ◽  
Grain Refinement ◽  
Grain Growth ◽  
Volume Fraction ◽  
Pure Titanium ◽  
Systematic Investigation ◽  
Second Phase ◽  
Titanium Matrix ◽  
Average Size

Addition of small amounts of erbium has a profound effect on recrystallization and grain growth in titanium. Erbium, because of its negligible solubility in titanium, precipitates in the titanium matrix as a finely dispersed second phase. The presence of this phase, depending on its average size, distribution, and volume fraction in titanium, strongly inhibits the migration of grain boundaries during recrystallization and grain growth, and thus produces ultimate grains of sub-micrometer dimensions. A systematic investigation has been conducted to study the isothermal grain growth in electrolytically pure titanium and titanium-erbium alloys (Er concentration ranging from 0-0.3 at.%) over the temperature range of 450 to 850°C by electron microscopy.

scholarly journals The Domain and Microstructure of Resin-Bonded Magnets

Materials ◽  
2021 ◽  
Vol 14 (11) ◽  
pp. 2849
Author(s):  
Marcin Jan Dośpiał
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Grain Size ◽  
Size Distribution ◽  
Domain Structure ◽  
Grain Size Distribution ◽  
Exchange Interactions ◽  
Force Microscopy ◽  
Transmission Electron ◽  
Scanning Electron

This paper presents domain and structure studies of bonded magnets made from nanocrystalline Nd-(Fe, Co)-B powder. The structure studies were investigated using scanning electron microscopy (SEM), high-resolution transmission electron microscopy (HRTEM), Mössbauer spectroscopy and X-ray diffractometry. On the basis of performed qualitative and quantitative phase composition studies, it was found that investigated alloy was mainly composed of Nd2(Fe-Co)14B hard magnetic phase (98 vol%) and a small amount of Nd1.1Fe4B4 paramagnetic phase (2 vol%). The best fit of grain size distribution was achieved for the lognormal function. The mean grain size determined from transmission electron microscopy (TEM) images on the basis of grain size distribution and diffraction pattern using the Bragg equation was about ≈130 nm. HRTEM images showed that over-stoichiometric Nd was mainly distributed on the grain boundaries as a thin amorphous border of 2 nm in width. The domain structure was investigated using a scanning electron microscope and metallographic light microscope, respectively, by Bitter and Kerr methods, and by magnetic force microscopy. Domain structure studies revealed that the observed domain structure had a labyrinth shape, which is typically observed in magnets, where strong exchange interactions between grains are present. The analysis of the domain structure in different states of magnetization revealed the dynamics of the reversal magnetization process.

The Synthesis of Cu0.81Ni0.19 Intermetallics by Mechanical Alloying

2012 ◽  
Vol 496 ◽  
pp. 379-382
Author(s):  
Rui Song Yang ◽  
Ming Tian Li ◽  
Chun Hai Liu ◽  
Xue Jun Cui ◽  
Yong Zhong Jin
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Grain Size ◽  
Mechanical Alloying ◽  
Milling Time ◽  
Elemental Powder ◽  
X Ray Diffraction ◽  
X Ray ◽  
Scherrer Equation ◽  
Scanning Electron

The Cu0.81Ni0.19 has been synthesized directly from elemental powder of nickel and copper by mechanical alloying. The alloyed Cu0.81Ni0.19 alloy powders are prepared by milling of 8h. The grain size calculated by Scherrer equation of the NiCu alloy decreased with the increasing of milling time. The end-product was analyzed by X-ray diffraction (XRD), scanning electron microscopy (SEM)

Light Burning Condition of Preparing Dolomite Clinker Using Natural Dolomite

2018 ◽  
Vol 281 ◽  
pp. 156-162
Author(s):  
Wang Nian Zhang ◽  
Xi Tang Wang ◽  
Zhou Fu Wang
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Grain Size ◽  
Sintering Process ◽  
X Ray Diffraction ◽  
Burning Temperature ◽  
X Ray ◽  
Temperature Range ◽  
Scanning Electron

The influence of the light burning temperature on the sintering property of nature dolomite has been investigated by two-step sintering process in the temperature range 1500 °C to 1600 °C. The resulting bulk densities and apparent porosities of the sintered dolomite samples were examined, and analyzing the sintered dolomite by scanning electron microscopy and X-ray diffraction were performed. The results showed light burned at 850 °C for 3 h, the main phases of the dolomite with 3-5 grain size were MgO, CaO and little CaCO3, and then fired at 1600 °C,the density of sintering dolomite reached to 3.38 g/cm3, the apparent property was 1.2 %, the size of MgO grain up to 3.75 μm . However when dolomite light burned at 1050 °C for 3 h, the main phases were MgO and CaO, and then fired at 1600 °C,the density of sintering dolomite only was 3.30 g/cm3, the apparent property was 2.3 %, the size of MgO only was 3.05 μm .

Homogeneous Al-Ti and Al-Ti-Si Thin Alloy Films

1985 ◽  
Vol 54 ◽  
Author(s):  
Albertus G. Dirks ◽  
Tien Tien ◽  
Janet M. Towner
Keyword(s):  
Thin Films ◽  
Heat Treatment ◽  
Grain Size ◽  
Electrical Resistivity ◽  
Phase Formation ◽  
Alloy Composition ◽  
Al Alloy ◽  
Second Phase ◽  
Alloy Films ◽  
Microstructure And Properties

ABSTRACTThe microstructure and properties of thin films depends strongly upon the alloy composition. A study was made of the metallurgical aspects of homogeneous Al alloy films, particularly the binary Al-Ti and the ternary Al-Ti-Si systems. Electrical resistivity, grain size morphology, second phase formation and electromigration have been studied as a function of the alloy composition and its heat treatment.

Comparative study of the oxide scale thermally grown on titanium alloys by ion beam analysis techniques and scanning electron microscopy

2008 ◽  
Vol 23 (8) ◽  
pp. 2245-2253 ◽  
Author(s):  
A. Gutiérrez ◽  
F. Pászti ◽  
A. Climent-Font ◽  
J.A. Jiménez ◽  
M.F. López
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Chemical Composition ◽  
Titanium Alloys ◽  
Oxide Scale ◽  
Ion Beam ◽  
Elastic Recoil ◽  
Detection Analysis ◽  
Nb Content ◽  
Scanning Electron

In the present work, the oxide layers developed at elevated temperature on three vanadium-free titanium alloys, of interest as implant biomaterials, were studied by Rutherford backscattering spectroscopy, elastic recoil detection analysis, and scanning electron microscopy. The chemical composition of the alloys investigated, in wt%, was Ti–7Nb–6Al, Ti–13Nb–13Zr, and Ti–15Zr–4Nb. Upon oxidation in air at 750 °C, an oxide scale forms, with a chemical composition, morphology, and thickness that depend on the alloy composition and the oxidation time. After equal exposure time, the Ti–7Nb–6Al alloy exhibited the thinnest oxide layer due to the formation of an Al2O3-rich layer. The oxide scale of the two TiNbZr alloys is mainly composed of Ti oxides, with small amounts of Nb and Zr dissolved. For both TiNbZr alloys, the role of the Nb-content on the mechanism of the oxide formation is discussed.

Sign in / Sign up

Export Citation Format

Share Document