Microwave Activation of Exfoliation in Ion–cut Silicon Layer Transfer

2007 ◽  
Vol 994 ◽  
Author(s):  
Douglas C. Thompson ◽  
T. L. Alford ◽  
J. W. Mayer ◽  
T. Hochbauer ◽  
J. K. Lee ◽  
...  
Keyword(s):  
Rutherford Backscattering Spectrometry ◽  
Silicon Layer ◽  
Silicon On Insulator ◽  
Cross Sectional ◽  
Selective Area ◽  
Atomic Force ◽  
Transmission Electron ◽  
Microwave System ◽  
Diffraction Patterns ◽  
Selective Area Electron Diffraction

AbstractMicrowave heating is used to initiate the ion-cut process for transfer of coherent silicon-layers onto insulator substrates. Hydrogen and boron co-implanted silicon was bonded to an insulative substrate before processing inside a 2.45 GHz, 1300 W cavity applicator microwave system. Sample temperatures measured using a pyrometer were comparable to previous ion – cut studies. Selected samples were further annealed to repair any damage created in the ion implant process. Rutherford backscattering spectrometry and selective area electron diffraction patterns show high crystallinity in transferred layers. RUMP simulation of backscattering spectra and cross-sectional transmission electron microscopy demonstrate that thicknesses of the transferred layers are comparable to previous ion-cut exfoliation techniques. Surface quality as characterized by an atomic force microscope compares well with previous ion-cut studies. Hall measurements were used to characterize electrical properties of transferred layers. The mobility and carrier density of microwave activated ion – cut silicon on insulator processed samples compares well with previous annealing techniques.

Polycrystalline Silicon Grown on Porous Silicon-on-Insulator Substrates

1996 ◽  
Vol 452 ◽  
Author(s):  
Klaus Y.J. Hsu ◽  
C. H. Lee ◽  
C. C. Yeh
Keyword(s):  
Porous Silicon ◽  
Low Temperature ◽  
Silicon Film ◽  
Silicon Layer ◽  
Porous Silicon Layer ◽  
Silicon On Insulator ◽  
Cross Sectional ◽  
Diffraction Patterns ◽  
Si Films ◽  
Soi Substrates

AbstractInexpensive full-wafer SOI substrates are appealing for various applications such as ULSI. As an attempt to achieve this goal, low-temperature deposition of silicon on novel porous Si-on-insulator (PSOI) substrates was performed in this work. The bottom insulator was obtained by anodically oxidizing a pre-formed porous silicon film in HCl solution. The thickness, uniformity and quality of the resulted bottom oxide layer as well as the residual porous silicon layer above were well-controlled. Low-temperature PECVD growth of silicon on the PSOI wafer was conducted by using the residual porous silicon as the seed. Cross-sectional TEM pictures and electron diffraction patterns showed that poly-Si films were formed on PSOI substrates under the conditions of 98% hydrogen dilution ratio, 20 Watts RF power, and 300°C substrate temperature. Further thermal annealing at 1050°C for 30 minutes significantly enhanced the crystallinity of the deposited films. Combined with the excellent insulation ability of the bottom oxide, the technique is suitable for future inexpensive full-wafer SOI fabrication.

An investigation of a nonspiking Ohmic contact to n-GaAs using the Si/Pd system

1988 ◽  
Vol 3 (5) ◽  
pp. 922-930 ◽  
Author(s):  
L. C. Wang ◽  
B. Zhang ◽  
F. Fang ◽  
E. D. Marshall ◽  
S. S. Lau ◽  
...  
Keyword(s):  
Ohmic Contact ◽  
Rutherford Backscattering Spectrometry ◽  
Tunneling Current ◽  
Solid State Reactions ◽  
Cross Sectional ◽  
Ohmic Behavior ◽  
Transmission Electron ◽  
Specific Contact ◽  
Diffraction Patterns ◽  
Ohmic Contact Formation

A low-resistance nonspiking Ohmic contact to n-GaAs is formed via solid-state reactions utilizing the Si/Pd/GaAs system. Samples with Si to Pd atomic ratios greater than 0.65 result in specific contact resistivity of the order of 10−6 Ω cm2, whereas samples with atomic ratios less than 0.65 yield higher specific contact resistivities or rectifying contacts. Rutherford backscattering spectrometry, cross-sectional transmission electron microscopy, and electron diffraction patterns show that a Pd, Si layer is in contact with GaAs with excess Si on the surface after the Ohmic formation annealing. This observation contrasts with that on a previously studied Ge/Pd/GaAs contact where Ohmic behavior is detected after transport of Ge through PdGe to the interface with GaAs. Comparing the Ge/Pd/GaAs system with the present Si/Pd/GaAs system suggests that a low barrier heterojunction between Ge and GaAs is not the primary reason for Ohmic contact behavior. Low-temperature measurements suggest that Ohmic behavior results from tunneling current transport mechanisms. A regrowth mechanism involving the formation of an n+ GaAs surface layer is proposed to explain the Ohmic contact formation.

Microwave Activation of Dopants & Solid Phase Epitaxy in Silicon

2007 ◽  
Vol 989 ◽  
Author(s):  
Douglas C. Thompson ◽  
J. Decker ◽  
T. L. Alford ◽  
J. W. Mayer ◽  
N. David Theodore
Keyword(s):  
Single Crystal ◽  
Microwave Heating ◽  
Rutherford Backscattering Spectrometry ◽  
Solid Phase ◽  
Single Crystal Silicon ◽  
Silicon Substrates ◽  
Crystal Silicon ◽  
Cross Sectional ◽  
Transmission Electron ◽  
Microwave System

AbstractMicrowave heating is used to activate solid phase epitaxial re-growth of amorphous silicon layers on single crystal silicon substrates. Layers of single crystal silicon were made amorphous through ion implantation with varying doses of boron or arsenic. Microwave processing occurred inside a 2.45 GHz, 1300 W cavity applicator microwave system for time-durations of 1-120 minutes. Sample temperatures were monitored using optical pyrometery. Rutherford backscattering spectrometry, and cross-sectional transmission electron microscopy were used to monitor crystalline quality in as-implanted and annealed samples. Sheet resistance readings show dopant activation occurring in both boron and arsenic implanted samples. In samples with large doses of arsenic, the defects resulting from vacancies and/or micro cluster precipitates are seen in transmission electron micrographs. Materials properties are used to explain microwave heating of silicon and demonstrate that the damage created in the implantation process serves to enhance microwave absorption.

Improvements in Zone Melt Recrystallized Soi Layers by the Use of Selective Epitaxial Growth in the Seed Windows.

1987 ◽  
Vol 107 ◽  
Author(s):  
D.A. Williams ◽  
R.A. McMahon ◽  
H. Ahmed ◽  
L. Karapiperis ◽  
G. Garry ◽  
...  
Keyword(s):  
Epitaxial Growth ◽  
Three Dimensional ◽  
Silicon Layer ◽  
Silicon On Insulator ◽  
Cross Sectional ◽  
Selective Epitaxial Growth ◽  
Beam System ◽  
Transmission Electron ◽  
The One ◽  
Zone Melt

AbstractThe effect of selective epitaxial growth (SEG) of silicon in the seed windows of silicon on insulator structures prior to recrystallization has been investigated. Subsequent zone melt recrystallization of these structures was performed in a dual electron beam system, and it was found that the full planarisation of the deposited silicon layer results in uniform film thickness after recrystallization. Cross sectional scanning and transmission electron microscopy, optical microscopy after defect etching, and bevelling are used to analyse the material. The SEG method improves the uniformity of the film for device island etching, and so is useful for all silicon on insulator applications, although the one of most interest for these investigations is the production of three dimensional circuitry. This is achieved by stacking layers of devices, and so planarity is particularly important.

scholarly journals Thin Ni Silicide Formation by Low Temperature-Induced Metal Atom Reaction with Ion Implanted Amorphous Silicon

1992 ◽  
Vol 279 ◽  
Author(s):  
Yu.N. Erokhin ◽  
B. K. Patnaik ◽  
S. Pramanick ◽  
F. Hong ◽  
C. W. White ◽  
...  
Keyword(s):  
Amorphous Silicon ◽  
Rutherford Backscattering Spectrometry ◽  
Silicon Layer ◽  
Amorphous Layer ◽  
Vacuum Furnace ◽  
Silicide Formation ◽  
Cross Sectional ◽  
Silicon Area ◽  
Transmission Electron ◽  
Silicide Growth

ABSTRACTWe have extended our recent work [1,2] on buried suicide formation by Ni diffusion into a buried amorphous silicon layer to the case where silicide formation is at lower temperatures on silicon substrates which have been preamorphized. The reaction of metal atoms from a 12 nm Ni film evaporated on top of a 65 nm thick surface amorphous layer formed by 35 keV Si+ ion implantation has been investigated at temperature ≤400 °C. Rutherford Backscattering Spectrometry (RBS) with channeling, cross-sectional transmission electron microscopy (XTEM), X-ray diffraction and four-point-probe measurements were used to determine the structure, interfacial morphology, composition and resistivity of the silicide films. It has been found that an increased rate of silicidation occurs for amorphous silicon with respect to crystalline areas permitting a selective control of the silicon area to be contacted during silicide growth. Vacuum furnace annealing at 360 °C for 8 hours followed by an additional step at 400 °C for one hour produces a continuos NiSi2 layer with a resistivity 44 μΩ cm.

High-resolution transmission electron microscopic study of highly oxygen doped silicon layer

1989 ◽  
Vol 47 ◽  
pp. 692-693
Author(s):  
H. Takaoka ◽  
M. Tomita ◽  
T. Hayashi
Keyword(s):  
High Resolution ◽  
Oxygen Concentration ◽  
Silicon Layer ◽  
Detailed Structure ◽  
Electron Microscopic ◽  
Cross Sectional ◽  
Transmission Electron ◽  
Doped Silicon ◽  
Argon Ion

High resolution transmission electron microscopy (HRTEM) is the effective technique for characterization of detailed structure of semiconductor materials. Oxygen is one of the important impurities in semiconductors. Detailed structure of highly oxygen doped silicon has not clearly investigated yet. This report describes detailed structure of highly oxygen doped silicon observed by HRTEM. Both samples prepared by Molecular beam epitaxy (MBE) and ion implantation were observed to investigate effects of oxygen concentration and doping methods to the crystal structure.The observed oxygen doped samples were prepared by MBE method in oxygen environment on (111) substrates. Oxygen concentration was about 1021 atoms/cm3. Another sample was silicon of (100) orientation implanted with oxygen ions at an energy of 180 keV. Oxygen concentration of this sample was about 1020 atoms/cm3 Cross-sectional specimens of (011) orientation were prepared by argon ion thinning and were observed by TEM at an accelerating voltage of 400 kV.

Temperature Dependent Quasi-Periodic Facetting of AlAs Grown by MBE on (100) GaAs Substrates

1993 ◽  
Vol 312 ◽  
Author(s):  
Richard Mirin ◽  
Mohan Krishnamurthy ◽  
James Ibbetson ◽  
Arthur Gossard ◽  
John English ◽  
...  
Keyword(s):  
Growth Conditions ◽  
High Energy ◽  
High Energy Electron ◽  
Temperature Dependent ◽  
Cross Sectional ◽  
Mbe Growth ◽  
Atomic Force ◽  
Gaas Substrates ◽  
Transmission Electron ◽  
Facet Formation

AbstractHigh temperature (≥ 650°C) MBE growth of AlAs and AlAs/GaAs superlattices on (100) GaAs is shown to lead to quasi-periodic facetting. We demonstrate that the facetting is only due to the AlAs layers, and growth of GaAs on top of the facets replanarizes the surface. We show that the roughness between the AlAs and GaAs layers increases with increasing number of periods in the superlattice. The roughness increases to form distinct facets, which rapidly grow at the expense of the (100) surface. Within a few periods of the initial facet formation, the (100) surface has disappeared and only the facet planes are visible in cross-sectional transmission electron micrographs. At this point, the reflection high-energy electron diffraction pattern is spotty, and the specular spot is a distinct chevron. We also show that the facetting becomes more pronounced as the substrate temperature is increased from 620°C to 710°C. Atomic force micrographs show that the valleys enclosed by the facets can be several microns long, but they may also be only several nanometers long, depending on the growth conditions.

Observation of the Wurtzite Phase in OMVPE Grown ZnSe/GaAs: Effect on Implantation and Rapid Thermal Annealing

1989 ◽  
Vol 147 ◽  
Author(s):  
K. S. Jones ◽  
J. Yu ◽  
P. D. Lowen ◽  
D. Kisker
Keyword(s):  
Thermal Annealing ◽  
Rapid Thermal Annealing ◽  
Electrical Transport ◽  
High Resistivity ◽  
Ion Milling ◽  
Electrical Transport Properties ◽  
Wurtzite Phase ◽  
Cross Sectional ◽  
Transmission Electron ◽  
Diffraction Patterns

AbstractTransmission electron diffraction patterns of cross-sectional TEM samples of OMVPE ZnSe on GaAs indicate the existence of the hexagonal wurtzite phase in the epitaxial layers. The orientation relationship is (0002)//(111); (1120)//(220). Etching studies indicate the phase is internal not ion milling induced. The average wurtzite particle size is 80Å-120Å. Because of interplanar spacing matches it is easily overlooked. Electrical property measurements show a high resistivity (1010ω/square) which drops by four orders of magnitude upon rapid thermal annealing between 700°C and 900 °C for 3 sec. Implantation of Li and N have little effect on the electrical transport properties. The Li is shown to have a high diffusivity, a solid solubility of ≈1016/cm3 at 800°C and getters to the ZnSeA/aAs interface.

Non-Destructive Assessment of Thin Film Stresses and Crystal Qualify of Silicon on Insulator Materials with Raman Spectroscopy

1990 ◽  
Vol 188 ◽  
Author(s):  
Ingrid De Wolf ◽  
Jan Vanhellemont ◽  
Herman E. Maes
Keyword(s):  
Thin Film ◽  
Electron Microscopy ◽  
Raman Spectroscopy ◽  
Cross Section ◽  
Silicon Layer ◽  
Silicon On Insulator ◽  
Micro Raman Spectroscopy ◽  
Transmission Electron ◽  
Non Destructive ◽  
Zone Melt

ABSTRACTMicro Raman spectroscopy (RS) is used to study the crystalline quality and the stresses in the thin superficial silicon layer of Silicon-On-Insulator (SO) materials. Results are presented for SIMOX (Separation by IMplanted OXygen) and ZMR (Zone Melt Recrystallized) substrates. Both as implanted and annealed SIMOX structures are investigated. The results from the as implanted structures are correlated with spectroscopic ellipsometry (SE) and cross-section transmission electron microscopy (TEM) analyses on the same material. Residual stress in ZMR substrates is studied in low- and high temperature gradient regions.

Epitaxial BaTiO3 Thin Films on Different Substrates for Optical Waveguide Applications

1999 ◽  
Vol 597 ◽  
Author(s):  
M. Siegert ◽  
Judit G. Lisoni ◽  
C. H. Lei ◽  
A. Eckau ◽  
W. Zander ◽  
...  
Keyword(s):  
Thin Films ◽  
Optical Waveguides ◽  
Rutherford Backscattering Spectrometry ◽  
Optical Data ◽  
X Ray Diffraction ◽  
X Ray ◽  
Force Microscopy ◽  
Ion Channeling ◽  
Atomic Force ◽  
Transmission Electron

AbstractIn the process of developing thin film electro-optical waveguides we investigated the influence of different substrates on the optical and structural properties of epitaxial BaTiO3 thin films. These films are grown by on-axis pulsed laser deposition (PLD) on MgO(100), MgAl2O4(100), SrTiO3(100) and MgO buffered A12O3(1102) substrates. The waveguide losses and the refractive indices were measured with a prism coupling setup. The optical data are correlated to the results of Rutherford backscattering spectrometry/ion channeling (RBS/C). X-ray diffraction (XRD), atomic force microscopy (AFM) and transmission electron microscopy (TEM). BaTiO3 films on MgO(100) substrates show planar waveguide losses of 3 dB/cm and ridge waveguide losses of 5 dB/cm at a wavelength of 633 nm.

Sign in / Sign up

Export Citation Format

Share Document