Impurity Removing at Dislocations in Float Zone Silicon by Aluminium-Silicon Alloying

1997 ◽  
Vol 469 ◽  
Author(s):  
I. Perichaud ◽  
S. Martinuzzi
Keyword(s):  
Electrical Activity ◽  
Front Surface ◽  
Mapping Technique ◽  
Induced Current ◽  
Standard Samples ◽  
Aluminium Layer ◽  
X Ray ◽  
Float Zone ◽  
Dislocation Arrays ◽  
Before And After

ABSTRACTAluminium-silicon alloying is applied to dislocation-containing FZ silicon samples in order to verify if this external gettering technique is able to remove impurities trapped by these defects. Samples were scratched (front surface), bent and annealed at 750°C for 6h in order to create dislocation arrays. Standard samples and also nickel contaminated samples were investigated by light beam induced current (LBIC) mapping technique before and after alloying at 900°C for 4h with a 1 μm thick aluminium layer deposited on the backside. The LBIC technique detects the features of the dislocation array in agreement with X ray topographs. In the standard samples, the contrast is relatedto an inadvertent contamination of the samples and disappears after gettering. In the contaminated samples, dislocation contrast is higher, the aluminium treatment attenuates strongly the dislocations electrical activity but not so neatly as for the standard samples. This result is explained by the possible microprecipitation of nickel at dislocations.

Defect structure in single crystal titanium carbide

1994 ◽  
Vol 9 (8) ◽  
pp. 2096-2101 ◽  
Author(s):  
Q.H. Zhao ◽  
J. Wu ◽  
A.K. Chaddha ◽  
H.S. Chen ◽  
J.D. Parsons ◽  
...  
Keyword(s):  
High Pressure ◽  
Titanium Carbide ◽  
Single Crystal ◽  
Edge Dislocation ◽  
Defect Structure ◽  
Double Crystal ◽  
Planar Defects ◽  
X Ray ◽  
Float Zone ◽  
Dislocation Arrays

The defects and crystallinity of as-grown and annealed TiCx (grown by the high-pressure float-zone) were examined by TEM and double crystal x-ray rocking curves. Three types of subboundaries and planar defects within subgrains were observed in as-grown TiCx. Subboundaries are classified by structure as (i) wide-extended, fault-like defects (WEFLD's), (ii) edge dislocation arrays, and (iii) dislocation networks. Planar defects were observed at dislocation nodes of subboundaries and also within subgrains; this is the first reported observation of planar defects within TiCx subgrains. The misorientation and/or density of subgrains in TiCx was reduced significantly by annealing at 2300 °C in contact with graphite.

Evaluation of Freezing Methods by Low Temperature X-Ray Diffraction

1977 ◽  
Vol 35 ◽  
pp. 330-333
Author(s):  
T. Gulik-Krzywicki ◽  
M.J. Costello
Keyword(s):  
Biological Materials ◽  
Molecular Organization ◽  
X Ray Diffraction ◽  
Glass Capillary ◽  
X Ray ◽  
Rate Dependent ◽  
Before And After ◽  
Freeze Etching ◽  
Diffraction Patterns ◽  
Set Up

Freeze-etching electron microscopy is currently one of the best methods for studying molecular organization of biological materials. Its application, however, is still limited by our imprecise knowledge about the perturbations of the original organization which may occur during quenching and fracturing of the samples and during the replication of fractured surfaces. Although it is well known that the preservation of the molecular organization of biological materials is critically dependent on the rate of freezing of the samples, little information is presently available concerning the nature and the extent of freezing-rate dependent perturbations of the original organizations. In order to obtain this information, we have developed a method based on the comparison of x-ray diffraction patterns of samples before and after freezing, prior to fracturing and replication.Our experimental set-up is shown in Fig. 1. The sample to be quenched is placed on its holder which is then mounted on a small metal holder (O) fixed on a glass capillary (p), whose position is controlled by a micromanipulator.

The Precipitation of Si in AlCuSi Thin Films

1973 ◽  
Vol 31 ◽  
pp. 34-35 ◽  
Author(s):  
R. M. Anderson
Keyword(s):  
Electron Microscopy ◽  
Thin Films ◽  
Heat Treatment ◽  
Solid Solution ◽  
Integrated Circuit ◽  
Copper Film ◽  
Solution Concentration ◽  
X Ray ◽  
Silicon Thin Films ◽  
Before And After

Aluminum-copper-silicon thin films have been considered as an interconnection metallurgy for integrated circuit applications. Various schemes have been proposed to incorporate small percent-ages of silicon into films that typically contain two to five percent copper. We undertook a study of the total effect of silicon on the aluminum copper film as revealed by transmission electron microscopy, scanning electron microscopy, x-ray diffraction and ion microprobe techniques as a function of the various deposition methods.X-ray investigations noted a change in solid solution concentration as a function of Si content before and after heat-treatment. The amount of solid solution in the Al increased with heat-treatment for films with ≥2% silicon and decreased for films <2% silicon.

Sorption of Se (IV) from aqueous solutions with subsequent determination by X-ray fluorescence analysis

2020 ◽  
Vol 86 (10) ◽  
pp. 5-9
Author(s):  
D. G. Filatova ◽  
A. A. Arkhipenko ◽  
M. A. Statkus ◽  
V. V. Es’kina ◽  
V. B. Baranovskaya ◽  
...  
Keyword(s):  
Inductively Coupled Plasma ◽  
Fluorescence Analysis ◽  
Standard Samples ◽  
Phase Contact Time ◽  
Sorbent Phase ◽  
X Ray ◽  
Fundamental Parameters ◽  
Inductively Coupled ◽  
Subsequent Determination

An approach to sorptive separation of Se (IV) from solutions on a novel S,N-containing sorbent with subsequent determination of the analyte in the sorbent phase by micro-x-ray fluorescence method is presented. The sorbent copolymethylenesulfide-N-alkyl-methylenamine (CMA) was synthesized using «snake in the cage» procedure and proven to be stable in acid solutions. Conditions for quantitative extraction of Se (IV) were determined: sorption in 5 M HCl or 0.05 M HNO3 solutions when heated to 60°C, phase contact time being 1 h. The residual selenium content in the solution was determined by inductively coupled plasma mass spectrometry (ICP-MS) using 82Se isotope. The absence of selenium losses is proved and the mechanism of sorption interaction under specified conditions is proposed. The method of micro-x-ray fluorescence analysis (micro-RFA) with mapping revealed a uniform distribution of selenium on the sorbent surface. The possibility of determining selenium in the sorbent phase by micro-RFA is shown. When comparing the obtained results with the results of calculations by the method of fundamental parameters, it is shown the necessity of using standard samples of sorbates to obtain correct results of RFA determination of selenium in the sorbent phase.

A New Polyethylene Corrosion Protecting Coating with Ion Selectivity

2011 ◽  
Vol 314-316 ◽  
pp. 273-278
Author(s):  
Yu Hua Dong ◽  
Ke Ren ◽  
Qiong Zhou
Keyword(s):  
Ion Selectivity ◽  
Nano Particles ◽  
Ammonium Bromide ◽  
Linear Low Density Polyethylene ◽  
X Ray Diffraction ◽  
Sulfosalicylic Acid ◽  
X Ray ◽  
Chemically Modified ◽  
Before And After ◽  
Industrial Standards

Linear low density polyethylene (LLDPE) was chemically modified with grafting maleic anhydride (MAH) monomer on its backbone by melting blending. Nano-particles SiO2 was modified by cationic surfactant hexadecyl trimethyl ammonium bromide (CTAB) and anionic surfactant sulfosalicylic acid (SSA) and added to PE coating respectively. Measurement of membrane potential showed that the coating containing modified SiO2 nano-particles had characteristic of ion selectivity. The properties of the different coatings were investigated according to relative industrial standards. Experimental results indicated that PE coating with ion selectivity had better performances, such as adhesion strength, cathodic disbonding and anti-corrosion, than those of coating without ion selectivity. Crystal structure of the coatings before and after alkali corrosion was characterized by Fourier transform infrared spectra (FTIR) and X-ray diffraction (XRD). Structure of the coating without ion selectivity was damaged by NaOH alkali solution, causing mechanical properties being decreased. And the structure of the ion selective coatings was not affected.

scholarly journals Synthesis of Novel Arginine-Based Flame Retardant and Its Application in Lyocell Fabric

Molecules ◽  
2021 ◽  
Vol 26 (12) ◽  
pp. 3588
Author(s):  
Jiayi Chen ◽  
Yansong Liu ◽  
Jiayue Zhang ◽  
Yuanlin Ren ◽  
Xiaohui Liu
Keyword(s):  
Fourier Transform ◽  
Heat Release ◽  
Flame Retardant ◽  
Photoelectron Spectroscopy ◽  
Fourier Transform Infrared ◽  
Ftir Analysis ◽  
Excellent Thermal Stability ◽  
X Ray ◽  
Cone Calorimeter Test ◽  
Before And After

Lyocell fabrics are widely applied in textiles, however, its high flammability increases the risk of fire. Therefore, to resolve the issue, a novel biomass-based flame retardant with phosphorus and nitrogen elements was designed and synthesized by the reaction of arginine with phosphoric acid and urea. It was then grafted onto the lyocell fabric by a dip-dry-cure technique to prepare durable flame-retardant lyocell fabric (FR-lyocell). X-ray photoelectron spectroscopy (XPS) and Fourier-transform infrared spectroscopy (FTIR) analysis demonstrated that the flame retardant was successfully introduced into the lyocell sample. Thermogravimetric (TG) and Raman analyses confirmed that the modified lyocell fabric featured excellent thermal stability and significantly increased char residue. Vertical combustion results indicated that FR-lyocell before and after washing formed a complete and dense char layer. Thermogravimetric Fourier-transform infrared (TG-FTIR) analysis suggested that incombustible substances (such as H2O and CO2) were produced and played a significant fire retarding role in the gas phase. The cone calorimeter test corroborated that the peak of heat release rate (PHRR) and total heat release (THR) declined by 89.4% and 56.4%, respectively. These results indicated that the flame retardancy of the lyocell fabric was observably ameliorated.

Sedimentary Clays as Geopolymer Precursor

2018 ◽  
Vol 39 ◽  
pp. 97-111
Author(s):  
F. Mostefa ◽  
Nasr Eddine Bouhamou ◽  
H.A. Mesbah ◽  
Salima Aggoun ◽  
D. Mekhatria
Keyword(s):  
Sodium Hydroxide ◽  
Mineralogical Composition ◽  
Cementitious Materials ◽  
Raw Material ◽  
X Ray Diffraction ◽  
Calcination Time ◽  
Calorimetric Analysis ◽  
X Ray ◽  
Before And After ◽  
Mechanical Performances

This work aims to study the feasibility of making a geopolymer cement based on dredged sediments, from the Fergoug dam (Algeria) and to evaluate their construction potential particularly interesting in the field of special cementitious materials. These sediments due to their mineralogical composition as aluminosilicates; are materials that can be used after heat treatment. Sedimentary clays were characterized before and after calcination by X-ray diffraction, ATG / ATD, spectroscopy (FTIR) and XRF analysis. The calcination was carried out on the raw material sieved at 80 μm for a temperature of 750 ° C, for 3.4 and 5 hours. The reactivity of the calcined products was measured using isothermal calorimetric analysis (DSC) on pastes prepared by mixing an alkaline solution of sodium hydroxide (NaOH) 8 M in an amount allowing to have a Na / Al ratio close to 1 (1: 1). Also, cubic mortar samples were prepared with a ratio L / S: 0.8, sealed and cured for 24 hours at 60 ° C and then at room temperature until the day they were submited to mechanical testing. to check the extent of geopolymerization. The results obtained allowed to optimize the calcination time of 5 hours for a better reactivity of these sediments, and a concentration of 8M of sodium hydroxide and more suitable to have the best mechanical performances.

Epitaxial Ni nanoparticles on CaF2(001), (110) and (111) surfaces studied by three-dimensional RHEED, GIXD and GISAXS reciprocal-space mapping techniques

2017 ◽  
Vol 50 (3) ◽  
pp. 830-839 ◽  
Author(s):  
S. M. Suturin ◽  
V. V. Fedorov ◽  
A. M. Korovin ◽  
N. S. Sokolov ◽  
A. V. Nashchekin ◽  
...  
Keyword(s):  
Lattice Structure ◽  
Three Dimensional ◽  
Grazing Incidence ◽  
High Energy ◽  
Reciprocal Space ◽  
Mapping Technique ◽  
Face Centered Cubic ◽  
X Ray ◽  
Cubic Lattice ◽  
Face Centered

The development of growth techniques aimed at the fabrication of nanoscale heterostructures with layers of ferroic 3dmetals on semiconductor substrates is very important for their potential usage in magnetic media recording applications. A structural study is presented of single-crystal nickel island ensembles grown epitaxially on top of CaF2/Si insulator-on-semiconductor heteroepitaxial substrates with (111), (110) and (001) fluorite surface orientations. The CaF2buffer layer in the studied multilayer system prevents the formation of nickel silicide, guides the nucleation of nickel islands and serves as an insulating layer in a potential tunneling spin injection device. The present study, employing both direct-space and reciprocal-space techniques, is a continuation of earlier research on ferromagnetic 3dtransition metals grown epitaxially on non-magnetic and magnetically ordered fluorides. It is demonstrated that arrays of stand-alone faceted nickel islands with a face-centered cubic lattice can be grown controllably on CaF2surfaces of (111), (110) and (001) orientations. The proposed two-stage nickel growth technique employs deposition of a thin seeding layer at low temperature followed by formation of the islands at high temperature. The application of an advanced three-dimensional mapping technique exploiting reflection high-energy electron diffraction (RHEED) has proved that the nickel islands tend to inherit the lattice orientation of the underlying fluorite layer, though they exhibit a certain amount of {111} twinning. As shown by scanning electron microscopy, grazing-incidence X-ray diffraction (GIXD) and grazing-incidence small-angle X-ray scattering (GISAXS), the islands are of similar shape, being faceted with {111} and {100} planes. The results obtained are compared with those from earlier studies of Co/CaF2epitaxial nanoparticles, with special attention paid to the peculiarities related to the differences in lattice structure of the deposited metals: the dual-phase hexagonal close-packed/face-centered cubic lattice structure of cobalt as opposed to the single-phase face-centered cubic lattice structure of nickel.

Sign in / Sign up

Export Citation Format

Share Document