PROPERTIES OF BOILER FUEL COMPOUNDED BY NARROW FUEL FRACTIONS

2021 ◽  
pp. 22-29
Author(s):  
K. Shevchenko ◽  
A. Grigorov ◽  
I. Sinkevich
Keyword(s):  
Raw Materials ◽  
Fire Hazard ◽  
Flash Point ◽  
Fuel Oil ◽  
Raw Material ◽  
Material Base ◽  
Boiler Fuel ◽  
Performance Properties ◽  
Lower Heat ◽  
The One

In order to improve the performance properties, in particular viscosity-temperature, of boiler fuel, it is proposed to combine them with narrow fuel fractions obtained by thermal destruction of secondary polymer raw materials (low pressure polyethylene and polypropylene). When compounding grade 100 fuel oil with narrow fuel fractions, the values ​​of density are reduced to 865 (873) kg / m3, conditional viscosity to 2.50 (2.63) deg. um., pour point up to 8 (13) °C), sulfur content up to 0.17 wt%. and the lower heat of combustion increases to 43606 (43850) kJ / kg. At the same time, there is a gradual decrease in the value of the flash point to 114 (127) °C. This reduction is a negative point, which leads to increased fire safety of fuel oil during its use, storage, pumping and transport. However, the values of the flash point, according to the requirements of regulatory documentation, are within acceptable limits. That is, the value of this indicator can limit the content of fuel oil in narrow fuel fractions. It is determined that the rational concentration of narrow fuel fractions in the composition of fuel oil grade 100, is within 30% of the mass. Within these limits, there is a permissible decrease in flash point values – an indicator that characterizes the fire hazard of fuel oil during its use, storage, pumping and transportation against the background of improving other performance properties of fuel oil. The production of the proposed compound boiler fuel on the one hand allows to expand the raw material base of the process by involving in the production process secondary polymer raw materials – solid waste subject to mandatory disposal, on the other – to meet existing demand for boiler fuel by increasing its production.

scholarly journals Advantages and Problems of the Development of Efficient Biofuel Production

2019 ◽  
Vol 9 (1) ◽  
pp. 7045-7051
Keyword(s):  
Raw Materials ◽  
Developed Countries ◽  
Fuel Oil ◽  
Raw Material ◽  
Biofuel Production ◽  
Material Base ◽  
Agricultural Enterprises ◽  
Oil Fuel ◽  
Oil Gas ◽  
Protein Feed

The article discusses the advantages and problems of the development of efficient biofuel production. The experience of developed countries in the production of biofuels from agricultural raw materials. Defined economic and social aspects. There is a political side to the production of renewable bioenergy. The availability of verified energy sources gives the country a certain temporary "margin of energy durability" in the event of a sudden interruption in the supply of traditional fuels (oil, fuel oil, gas) and some opportunity for maneuvering energy resources within the state. The development of bioenergy based on the use of its own raw material base is economically feasible. This is not only biofuels and fertilizers, but also high-protein feed for livestock and poultry, as well as the possibility of energy supply of specific agricultural enterprises.

Modification of Technological Properties of Laboratory Premixes

2018 ◽  
Vol 276 ◽  
pp. 236-241
Author(s):  
Iveta Hájková ◽  
Petr Novosad
Keyword(s):  
Czech Republic ◽  
Flue Gas ◽  
Raw Materials ◽  
Waste Product ◽  
Raw Material ◽  
Material Base ◽  
Limited Capacity ◽  
The Czech Republic ◽  
Mixed Mortar ◽  
The One

Sulfur binders belong to the group of airbrushes. They can therefore only harden and harden in the air. The main raw material, gypsum, can be mined in several places in the world. Even in the Czech Republic there is a deposit of natural gypsum in Kobeřice u Opavy. [5] In spite of this fact, we use mostly industrially produced gypsies, because the natural gypsum deposit has only very limited capacity. The Energogypsum, produced in the Czech Republic by ČEZ Energetické Produkty s.r.o., is the waste product of flue gas desulphurization using the wet limestone scrubbing method. Like the chemosynthesis, it is characterized by its high purity (the content of pure CaSO4 2 H2O is at least 90%). The one in the Czech Republic is manufactured by Precheza, a.s. in Přerov. The use of sulphate binders is varied. A better form in the form of alpha plaster is used to produce self-leveling floors and dentistry. Less-quality beta gypsum has a larger application. From it we can produce both gypsum and monolithic partitions. We can also use it for the production of plasterboard and gypsum fiber boards and, last but not least, as internal plasters for its good fire performance. [1] Plasters are being prepared today in two different ways. Firstly, they are still prepared in the original outpatient way directly on the building from individual raw materials, but they are also industrially produced in the form of dry mortar mixtures, which are mixed on the building only with water. The second way is more progressive with the fact that nowadays it is even more widespread. For many builders, however, it remains financially scarce. That is why we have recently begun to find a compromise solution that will satisfy both the technical and the economic ones. This is the development of the so-called binder premixes, ie the industrially produced mixed binder, which is mixed only with sand and water on the site. The situation on our market shows that the recently developed special premix for lime-cement plaster and mortar mixtures is very positive for the building public and therefore the effort is to generalize this mixed mortar in the production raw material base and, in addition, to develop its analogue based on sulphate binder. [2]

Adjustment of a technology of cast iron smelting in the blast furnace of jsc "ural steel" w ith a volume of 1232 см3 with charge h a v in g 95% share of Mikhailovskii GOK pellets

2021 ◽  
Vol 77 (7) ◽  
pp. 768-775
Author(s):  
I. F. Iskakov ◽  
G. A. Kunitsyn ◽  
D. V. Lazarev ◽  
А. А. Red`kin ◽  
S. A. Trubitsyn ◽  
...  
Keyword(s):  
Blast Furnace ◽  
Iron Ore ◽  
Raw Materials ◽  
Raw Material ◽  
Material Base ◽  
Hot Metal ◽  
Charging System ◽  
Iron Smelting ◽  
Gas Consumption ◽  
A Charge

To use effectively internal raw material base, JSC “Ural Steel” accomplished I category major overhaul of the blast furnace No. 2. The main purpose of the overhaul was to design a rational profile which could ensure an ability to operate with a charge containing 95 % of Mikhailovskii GOK (mining and concentrating plant) pellets having basicity of 0.5 by CaO/SiO2. The blast furnace No. 2 having useful volume of 1232 m3, was constructed by design of Danieli Corus, the Netherlands, and was blown in on December 30, 2020. In the process of guarantee tests, step-by-step increase of Mikhailovskii GOK pellets (Fetotal = 60.5 %, CaO/SiO2 = 0.5) content in the charge iron ore part was being accomplished from 55 to 95.1%. Charging of the blend containing pellets in the amount of 55% of iron ore part, was done by charging system 4OOCC + 1COOCC (Ore - Coke) with filling level 1.5 m. Under conditions of pellets part increase in the blend, the charging system was changed to decrease their content at the periphery, to increase it in the ore ridge zone and make it intermediate between periphery and the ore ridge. At the pellets share in the iron ore raw materials 0.75 the charging system was used as the following: 3OOCC + 1COOC + 1COOCC, while at the content 95.1% the following charging system was used: 2COOC + 2COOC + 1COOCC. It was noted that in the period of guarantee tests the furnace running was smooth. The average silicon content in the hot metal was 0.70% at the standard deviation 0.666. Sulfur content in the hot metal did not exceed 0.024%, the blowing and natural gas consumption figures were 2100 m3/min and 11000 m3/min correspondently, oxygen content in the blowing 26.5%, hot blowing and top smoke pressure figures were 226.5 and 109.8 KPa correspondently. The productivity of the furnace was reached as high as 2358 t/day at the specific coke rate 433 kg/t of hot metal. After guarantee tests completion, the pellets content in the iron ore part was decreased gradually from 95 down to 50%. The decreasing was made by 5% in every 6 hours of operation. Application of the mastered technology of the blast furnace No. 2 with the increased share of pellets will enable to stably supply the blast furnaces No. 1, 3 and 4 by iron ore raw materials in the proportion of 30-35% of pellets and 65-70% of sinter.

Serpentinite Magnesium Binders, Based on Technogenic Raw Materials

2021 ◽  
Vol 316 ◽  
pp. 1050-1054
Author(s):  
V.N. Zyryanova ◽  
E.V. Lytkina ◽  
A.P. Ochur-Ool
Keyword(s):  
Mechanical Strength ◽  
Water Resistance ◽  
Raw Materials ◽  
Raw Material ◽  
Material Base ◽  
Hardening Process ◽  
Dispersed System ◽  
Technogenic Raw Materials

Increasing water resistance and mechanical strength of hardening magnesian binders’ products can be achieved by introducing microfillings into a hardening dispersed system. It is shown that serpentine provides an increase strength and water resistance in hydration and hardening process, being as a structure-forming component, it intensifies this process. It allows expanding the raw material base for the production of magnesia binders for construction purposes.

Technological aspects of alcohol distillates production from non-traditional sugar-raw materials

2021 ◽  
Vol 9 (16) ◽  
pp. 90-97
Author(s):  
Kateryna Danilova ◽  
◽  
Oksana Zavarzina ◽  
Keyword(s):  
Raw Materials ◽  
Biologically Active ◽  
Raw Material ◽  
Material Base ◽  
Growth Substances ◽  
Technological Properties ◽  
Actual Problem ◽  
Cane Molasses ◽  
Yeast Biomass ◽  
Nitrogen Phosphorus

An actual problem of the alcohol industry development is the expansion of the raw material base through the use of new, cheaper types of carbohydrate sources. Recently, glucose-fructose syrup has been of increasing interest to producers of ethanol. Among the producers of craft drinks, in particular rum-based drinks, cane molasses is in increasing demand. The article presents the technological aspects of the fermentation process of nonconventional sugar-containing raw materials on the example of glucose-fructose syrup and cane molasses in ethanol by different yeast strains. It is determined that glucose-fructose syrup and cane molasses are raw materials depleted of nitrogen, phosphorus and growth substances necessary for the yeast activity. To improve the technological properties of raw materials in the molasses, nitrogen, phosphorus nutrition and corn extract as a growth substance shall be added to a mash. Glucose-fructose syrup is of pH 3.68 and of acidity 0.12, which negatively affects the fermentation. It is established that in order to create optimal living conditions for yeast, it is necessary to add substances to the glucose-fructose syrup that will contribute to the safety of development and prevent the pH 3.5. It was determined that the alcohol yield from 1 ton of glucose-fructose syrup is 31.0 dal, from 1 ton of cane molasses is 24.0 dal on the yeast 46ED and 22 dal on the TegaYeast without the use of growth substances and vitamins necessary for the reproduction of yeast biomass. Under conditions of improving the technological properties of the mash from the glucose-fructose syrup and cane molasses by adding biologically active substances promoting the synthesis of yeast biomass, the ethanol content in the fermented mashes increases up to 11.9 12% vol.

scholarly journals Antimicrobial Activity and Polyphenol Profiles of Hydroalcoholic Extracts of Thymus rasitatus Klokov and Thymus eremita Klokov

2021 ◽  
Vol 9 (A) ◽  
pp. 313-317
Author(s):  
Svetlana Ivasenko ◽  
Ainur Zhumabekova ◽  
Agnieszka Ludwiczuk ◽  
Krystyna Skalicka–Wozniak ◽  
Alexandr Marchenko ◽  
...  
Keyword(s):  
Antimicrobial Activity ◽  
Chromatographic Analysis ◽  
Antimicrobial Agents ◽  
Raw Materials ◽  
Wide Spectrum ◽  
Raw Material ◽  
Thymus Vulgaris ◽  
Material Base ◽  
Ultrasound Assisted Extraction ◽  
Ethanol Extracts

BACKGROUND: A possible reduction in stocks of medicinal plant raw materials of Thymus serpyllum L. and Thymus vulgaris L. leads to the need to expand the raw material base of the official medicinal plants with using of endemic species of the flora of Kazakhstan, in particular, Thymus rasitatus Klokov, and Thymus eremita Klokov. AIM: The aim of the study was to study the possibility of using 70% ethanol extracts of T. rasitatus and T. eremita as antimicrobial agents. MATERIALS AND METHODS: The aerial parts of T. rasitatus and T. eremita were extracted with 70% ethanol using ultrasound assisted extraction. The qualitative and quantitative analyses of the 70% ethanol extracts were determined using the liquid chromatography-detection-ESI-mass spectrometry-(MS)/MS technique. The study of the antimicrobial activity of these extracts was performed for eight strains of Gram-positive bacteria, six strains of Gram-negative bacteria, and four cultures of fungi. RESULTS: Chromatographic analysis of hydroalcoholic extracts of both investigated Thymus species showed very similar phenolic compounds composition. In both cases, the major components are luteolin-7-O-glucoside and rosmarinic acid. About 70% ethanol extracts of T. rasitatus and T. eremita have a broad spectrum of antimicrobial activity, exhibit the bactericidal or bacteriostatic activity against all tested bacteria and fungi at concentration range of 0.0195–20 mg/ml, but differ in their potency against tested strains of microorganisms. CONCLUSION: About 70% ethanol extracts of T. rasitatus and T. eremita, endemic plants in the flora of Kazakhstan, can be considered as potential drugs with a wide spectrum of antimicrobial activity. The results of chromatographic analysis could be used for drug standardization.

scholarly journals Physical and Chemical Fundamentals and Technical Solutions for Recovery of Non-ferrous and Rare Metals from Industrial Wastes

2020 ◽  
Author(s):  
P.A. Kozlov ◽  
A.M. Panshin ◽  
L.I. Leontiev
Keyword(s):  
Russian Federation ◽  
Raw Materials ◽  
Block Diagram ◽  
Industrial Wastes ◽  
Raw Material ◽  
Material Base ◽  
Waelz Process ◽  
Zinc Cadmium ◽  
The Russian Federation ◽  
Increasing Demand

The increasing demand for zinc and a range of zinc-related metals (for example: lead; indium; tin; cadmium; and copper) in the Russian Federation cannot be satisfied by the existing production plants due to the lack of raw materials. At the same time, ferrous and non-ferrous metallurgy and the chemical industry have accumulated hundreds of millions of tons of zinc wastes (falling into the hazard categories 2 to 4), the processing of which could not only make up the raw material base, but also improve the environmental situation. In the world, over 85% of ferrous dust is recycled using the Waelz process. The Waeltz process is used for distilling separation of elements under reducing conditions. In this study, a block diagram for production of the following elements from industrial wastes is proposed: zinc, cadmium and indium in form of massive metals; zinc and indium in the form of fine powders; and clinker as a raw material for cement production. The technical and scientific details of this new process have been patented in the Russian Federation and abroad. For the first time, the following operations have been implemented with the use of large-sized Waelz kilns: vapour-oxidized Waeltz treatment of polymetallic wastes; recycling of heat from gases and solid products with generation of process fumes; and implementation of alternative flux (dolomite) and alternative fuel (petroleum coke). Keywords: Waelz process, industrial wastes, heat recycling, vapour-oxidized Waelz processing

scholarly journals PERSPECTIVES FOR DEVELOPMENT OF TECHNICAL BUILDING STONE- LIMESTONE IN THE REPUBLIC SRPSKA

2015 ◽  
Vol 1 (12) ◽  
Author(s):  
Slobodan Majstorović ◽  
Vladimir Malbašić ◽  
Miodrag Čelebić
Keyword(s):  
Raw Materials ◽  
Production Capacity ◽  
Mineral Resources ◽  
Building Stone ◽  
Raw Material ◽  
Material Base ◽  
Standard Quality ◽  
The Republic ◽  
Fragmentation Of Production ◽  
Republika Srpska

Curent situation of raw material base and study of limestone like construction stone deposits in the Republic of Serbian were relatively poorly considered during the last decades, and the main problems are the following: low production capacity fragmentation of production, needs for raw materials homogenization and delivering of standard quality, undeveloped market, the recession of the domestic economy and the economies in the region, the relatively low level of exploration by many deposits, especially lack of knowledge of the occurrence legality for certain types and quality of raw materials and lack of complete quality indicators for raw material, which sometimes causes the utilization of only the highest quality deposit parts.This paper provides an overview of active quarries in the Republic Srpska with exploitation of limestone like technical building stone and present an attempt to determine the basic quantitative and qualitative characteristics of the raw material and the current working conditions at these quarries. The purpose of such a review would be in an effort to create a clearer picture about production, market, social and other aspects of the limestone exploitation in the Republika Srpska and the realistic possibilities of maintaining and developing of these mineral resources utilization, which can certainlybe interesting for the development of many other industries in the Republic Srpska.

scholarly journals Construction sands of Podillya: patterns of distribution, resources and use

2019 ◽  
Vol 27 (3) ◽  
pp. 510-519
Author(s):  
M. Syvyj ◽  
B. Gavrychok
Keyword(s):  
Raw Materials ◽  
Raw Material ◽  
Simultaneous Increase ◽  
Clay Material ◽  
Material Base ◽  
Resource Base ◽  
Apparent Correlation ◽  
The Baltic ◽  
Further Development

This article presents the characteristics of the resource base of building sands within the three Podillya regions, the patterns of sands distribution, and proposals for increasing the extraction of raw materials . The construction sands of Podillya are confined to the Upper Cretaceous, Neogene and Anthropogenicdeposits. The decrease of the thickness of the sandy strata of the Opilsk Neogene suite in the eastern direction was observed with the simultaneous increase in the thickness of the overlapping strata of the rocks. There is no apparent correlation between the thickness of sandy interlayers and the quality of sands. The interdependence of the chemical composition of Neogene sands and the sand size module is established.The genetic predisposition for the distribution of building sands in different parts of the Podillya territory has been established. Four groups of sand deposits of different age have been identified within the Podillya regions, which contrast sharply with single deposits in the neighbouring territories.There is a very uneven distribution of explored reserves of sandy raw materials across the region and accordingly in the provision of construction sands in the different oblasts /regions of Podillya. The areas best provided with sandy raw materials are the central districts of Ternopil region and Slavutsky district of Khmelnytsky region . Sands of the Baltic stage distributed in Vinnytsia region are mostly poor in quality, clogged with clay material and require enrichment. The further development of the mineral raw material base and the prospects for increasing the production of construction sand in the Podillya regions is associated with the increase in production at the prepared deposits, the commissioning of reserve deposits, the conducting of prospecting and exploration work in the proposed potentially exploitable areas and additional exploration of individual deposits that are exploited. The research allows us to evaluate objectively the existing base of sand raw materials for various purposes in the Podillya region and to develop on this basis measures to increase it. The importance of the study is determined by the acute shortage of the raw material in most administrative districts of Khmelnytsky and Vinnytsia regions, by the growth in the volume of construction work (and accordingly the requirements for sandy raw materials) both in Podillya and in the country.

scholarly journals Industrial characteristics of Berberis L. representatives fruits

2018 ◽  
Vol 47 ◽  
pp. 63-69
Author(s):  
Yu. V. Lykholat ◽  
N. O. Khromykh ◽  
T. Yu. Lykholat ◽  
M. I. Nedzvetska ◽  
O. A. Lykholat ◽  
...  
Keyword(s):  
Food Industry ◽  
Seed Quality ◽  
Raw Materials ◽  
Low Frequency ◽  
Botanical Garden ◽  
Raw Material ◽  
Material Base ◽  
Total Antioxidant ◽  
Fruit Plants ◽  
Seed Propagation

The introduction of fruit plants into a culture enriches the diversity of the species composition of the regional flora and at the same time creates an opportunity for expansion of the plant raw material base for the needs of the food industry, inclusion in a full-fledged functional nutrition of the population. Among the fruit plants of the Dniprovsk region, every year, more attention should be paid to introduced low-frequency non-traditional fruit species, in which the fruits, leaves, stems and other parts have high nutritional value and are the source of physiologically active compounds that have anti-cancer, antibacterial and anti-inflammatory properties, carry cardio protective, antihypertensive, anti-diabetic effects, stimulate the central nervous system, etc., and can contribute to the prevention and treatment of many diseases.   Antioxidants additives in the raw materials and finished products ensures their prevention damage, reduce losses, increase shelf life and production of high quality products which keep for a long time characteristics inherent fresh, complete products. Preservation, restoration and introduction to the culture of any species depends primarily on its ability to multiply seed and vegetative methods. A comparative analysis of the fruit and seed ability of Berberis L. representatives grown in the botanical garden of Oles Gonchar’  Dniprovsky National University was carried out. The use of integrated research methods made it possible to carry out an integrated assessment of the regenerative capacity of the investigated representatives of the Berberis L. and to establish their biological ability to seed propagation depending on the seed quality of the seeds. The seeds length varied from 4.5 mm (B. canadensis) to 5.2 mm (B. declinata, B. amurensis), width was from 1.8 mm (B. amurensis, B. vulgares) to 2.1 mm ( B. coreana). The weight of 1000 seeds, which, depending on their size and completeness, amounted to an average of 10.16 grams. Largest weight 1000 pcs. seed is marked in B. coreana. As a result of the total antioxidant ability of the fruits, the species examined can be arranged in the following order:  B. koreana > B. x declinata > B. vulgaris > B. amurensis > B. canadensis. When comparing total antioxidant capacity level of the plants, the highest indices were characteristic for B. koreana and B. x declinata fruits, which exceeded the values of other species in 1.7-1.9 times. The relatively low antioxidants concentration in B. amurensis fruits is offset by a greater weight of the fruits of this species.  In order to enrich the range of ornamental and fruit plants, it is expedient to introduce into production of new crops and to expand the species diversity of Berberis L. representatives. Barberry reproduction process depends on many factors related to the environment. All investigated representatives of the Berberis L. are promising for further use in the planting system and as fruit plants that can be included in the functional nutrition of the population and use in the food industry in the conditions of the Steppe Prydniprovya.

Sign in / Sign up

Export Citation Format

Share Document