scholarly journals Advantages and Problems of the Development of Efficient Biofuel Production

2019 ◽  
Vol 9 (1) ◽  
pp. 7045-7051
Keyword(s):  
Raw Materials ◽  
Developed Countries ◽  
Fuel Oil ◽  
Raw Material ◽  
Biofuel Production ◽  
Material Base ◽  
Agricultural Enterprises ◽  
Oil Fuel ◽  
Oil Gas ◽  
Protein Feed

The article discusses the advantages and problems of the development of efficient biofuel production. The experience of developed countries in the production of biofuels from agricultural raw materials. Defined economic and social aspects. There is a political side to the production of renewable bioenergy. The availability of verified energy sources gives the country a certain temporary "margin of energy durability" in the event of a sudden interruption in the supply of traditional fuels (oil, fuel oil, gas) and some opportunity for maneuvering energy resources within the state. The development of bioenergy based on the use of its own raw material base is economically feasible. This is not only biofuels and fertilizers, but also high-protein feed for livestock and poultry, as well as the possibility of energy supply of specific agricultural enterprises.

PROPERTIES OF BOILER FUEL COMPOUNDED BY NARROW FUEL FRACTIONS

2021 ◽  
pp. 22-29
Author(s):  
K. Shevchenko ◽  
A. Grigorov ◽  
I. Sinkevich
Keyword(s):  
Raw Materials ◽  
Fire Hazard ◽  
Flash Point ◽  
Fuel Oil ◽  
Raw Material ◽  
Material Base ◽  
Boiler Fuel ◽  
Performance Properties ◽  
Lower Heat ◽  
The One

In order to improve the performance properties, in particular viscosity-temperature, of boiler fuel, it is proposed to combine them with narrow fuel fractions obtained by thermal destruction of secondary polymer raw materials (low pressure polyethylene and polypropylene). When compounding grade 100 fuel oil with narrow fuel fractions, the values ​​of density are reduced to 865 (873) kg / m3, conditional viscosity to 2.50 (2.63) deg. um., pour point up to 8 (13) °C), sulfur content up to 0.17 wt%. and the lower heat of combustion increases to 43606 (43850) kJ / kg. At the same time, there is a gradual decrease in the value of the flash point to 114 (127) °C. This reduction is a negative point, which leads to increased fire safety of fuel oil during its use, storage, pumping and transport. However, the values of the flash point, according to the requirements of regulatory documentation, are within acceptable limits. That is, the value of this indicator can limit the content of fuel oil in narrow fuel fractions. It is determined that the rational concentration of narrow fuel fractions in the composition of fuel oil grade 100, is within 30% of the mass. Within these limits, there is a permissible decrease in flash point values – an indicator that characterizes the fire hazard of fuel oil during its use, storage, pumping and transportation against the background of improving other performance properties of fuel oil. The production of the proposed compound boiler fuel on the one hand allows to expand the raw material base of the process by involving in the production process secondary polymer raw materials – solid waste subject to mandatory disposal, on the other – to meet existing demand for boiler fuel by increasing its production.

scholarly journals History of prospecting and development of deposits of quartz raw materials in the Urals and the prospect of their further use

2021 ◽  
pp. 48-59
Author(s):  
POLENOV Yuriy Alekseevich ◽  
◽  
OGORODNIKOV Vitaliy Nikolaevich ◽  
KISIN Aleksandr Yur’evich ◽  
◽  
...  
Keyword(s):  
Fiber Optics ◽  
Raw Materials ◽  
Developed Countries ◽  
Ural Region ◽  
Raw Material ◽  
Light Sources ◽  
Material Base ◽  
The Urals ◽  
Mining Operations ◽  
History Of

Relevance of the work. For 60 years of hard work of quartz workers in the geological industry, Soviet geologists have fully provided the USSR industry for many years to come with piezoquartz and high-grade, highly pure quartz for the production of all types of quartz products. Much has changed over the years; and it became necessary to analyze the existing raw material base of Russia for quartz for smelting. Purpose of the work: analysis of the existing raw material base of Russia for quartz raw materials and the role of the deposits of quartz raw materials in the Ural region in solving this problem. Research methodology. The history of the use of quartz material as an industrial raw material and its application by the most developed countries of Europe is briefly outlined. It is shown that in the presence of various genetic types of quartz in the territory of Russia, the main deposits of highly pure quartz are located within the Ural region. The history of the complex and multiple reorganization of geological units that carried out prospecting, exploration, production and processing of all types of quartz raw materials from the Urals deposits is considered in detail. With the aim of centralization of exploration, mining operations, the production of industrial products from quartz and gemstones, scientific and project construction works in the Urals, the production association Uralkvartssamotsvety has been established since November 1, 1977. In terms of its technological equipment, the level of technology and organization of production, the achieved technical and economic indicators and allocations, the Uralkvartszamotsvety association was the flagship among the related associations of the USSR Ministry of Geology. Conclusions. Nowadays, the severe issue of the raw material base of quartz in Russia is the provision of the domestic industry with raw materials for the fusion of special transparent quartz glasses used primarily in microelectronics, fiber optics, and the production of high-intensity light sources. Ural had been and could continue to be the main supplier of raw materials and especially pure quartz. The reserves of these types of raw materials are significant, and the deposits are located in favorable economic and geographical areas.

scholarly journals MILK AND DAIRY PRODUCTS MARKET IN AKMOLA REGION OF KAZAKHSTAN

2020 ◽  
Vol 4 ◽  
pp. 125-132
Author(s):  
B.K. NASSYRKHANOVA ◽  
◽  
A.S. BELGIBAYEVA ◽  
Keyword(s):  
Dairy Products ◽  
Raw Materials ◽  
Raw Milk ◽  
Raw Material ◽  
Material Base ◽  
Agricultural Enterprises ◽  
Close Relationship ◽  
Dairy Cattle Breeding ◽  
Effective Development ◽  
Milk And Dairy Products

Recommendations for solving the problems of sustainable development of milk and dairy products market in the region are based on the study of its current state and promising directions. The dynamics of production of milk and its processing products, export and import, livestock and productivity of cows is analyzed. The contribution of various categories of farms to the receipt of raw milk has been studied, while the lag in milk yield in farms and households from agricultural enterprises has been revealed. The analysis of expenses in agricultural enterprises is presented, as well as the structure of material costs. The main problems of effective development of the industry of dairy cattle breeding include tendency to reduce the area under fodder crops; a weak feed base and increase in feed prices, which leads to the increase in the cost of milk; reduction in the number of dairy cows; small commodity farms, that is, the concentration of main volumes of milk production in households where the introduction of intensive innovative technologies is difficult; seasonality of the process; non-observance of veterinary and sanitary standards. The regional features of location of dairy processing enterprises have been investigated, confirming the close relationship between the development of the dairy industry and the raw material base. Those of them have been identified, which account for the largest share in production of the range of dairy products. The organizational structure of the milk processing enterprise "Gormolzavod" LLP was studied, the calculation of butter was made using its own raw materials. The competitive advantages of the processing enterprises of the region are revealed.

UNIDO, Industrial Processing of Natural Resources. New York: United Nations. 1981. viii + 78pp.US $ 5.00. [United Nations Publication Sales No. E. 81. 11 . B.1]

1982 ◽  
Vol 21 (4) ◽  
pp. 329-333
Author(s):  
Rashid Aziz
Keyword(s):  
New York ◽  
United Nations ◽  
Industrial Development ◽  
Raw Materials ◽  
Developed Countries ◽  
Raw Material ◽  
Industrial Processing ◽  
Depth Study ◽  
Manufactured Exports ◽  
Year 2000

The book under review is a concise but fairly in-depth study of the prospects for export diversification from the Less Developed Countries (henceforth labeled as LDCs) particularly to Developed Countries (henceforth labeled as OCs). Given the multiple problems faced by the LOCs in exporting to the OCs - protectionist policies with regards to manufactured exports, volatility of prices obtained for raw material exports, etc. - the study analyses the potential for following an intermediate route. The important issues in the export of semi -processed and wholly processed raw materials are discussed. 111ese issues range from the problems and potentials for the location of processing facilities in the LOCs to the formulation of appropriate policies to encourage an export of processed goods rather than raw materials. Such policies will be useful both in solving the balance of-payments problems of the LDCs and in attaining the goal of the Lima Declaration and Plan of Action on Industrial Development and Co-operation, that called for 2S percent of world industrial production to be located in the LOCs by the year 2000.

Adjustment of a technology of cast iron smelting in the blast furnace of jsc "ural steel" w ith a volume of 1232 см3 with charge h a v in g 95% share of Mikhailovskii GOK pellets

2021 ◽  
Vol 77 (7) ◽  
pp. 768-775
Author(s):  
I. F. Iskakov ◽  
G. A. Kunitsyn ◽  
D. V. Lazarev ◽  
А. А. Red`kin ◽  
S. A. Trubitsyn ◽  
...  
Keyword(s):  
Blast Furnace ◽  
Iron Ore ◽  
Raw Materials ◽  
Raw Material ◽  
Material Base ◽  
Hot Metal ◽  
Charging System ◽  
Iron Smelting ◽  
Gas Consumption ◽  
A Charge

To use effectively internal raw material base, JSC “Ural Steel” accomplished I category major overhaul of the blast furnace No. 2. The main purpose of the overhaul was to design a rational profile which could ensure an ability to operate with a charge containing 95 % of Mikhailovskii GOK (mining and concentrating plant) pellets having basicity of 0.5 by CaO/SiO2. The blast furnace No. 2 having useful volume of 1232 m3, was constructed by design of Danieli Corus, the Netherlands, and was blown in on December 30, 2020. In the process of guarantee tests, step-by-step increase of Mikhailovskii GOK pellets (Fetotal = 60.5 %, CaO/SiO2 = 0.5) content in the charge iron ore part was being accomplished from 55 to 95.1%. Charging of the blend containing pellets in the amount of 55% of iron ore part, was done by charging system 4OOCC + 1COOCC (Ore - Coke) with filling level 1.5 m. Under conditions of pellets part increase in the blend, the charging system was changed to decrease their content at the periphery, to increase it in the ore ridge zone and make it intermediate between periphery and the ore ridge. At the pellets share in the iron ore raw materials 0.75 the charging system was used as the following: 3OOCC + 1COOC + 1COOCC, while at the content 95.1% the following charging system was used: 2COOC + 2COOC + 1COOCC. It was noted that in the period of guarantee tests the furnace running was smooth. The average silicon content in the hot metal was 0.70% at the standard deviation 0.666. Sulfur content in the hot metal did not exceed 0.024%, the blowing and natural gas consumption figures were 2100 m3/min and 11000 m3/min correspondently, oxygen content in the blowing 26.5%, hot blowing and top smoke pressure figures were 226.5 and 109.8 KPa correspondently. The productivity of the furnace was reached as high as 2358 t/day at the specific coke rate 433 kg/t of hot metal. After guarantee tests completion, the pellets content in the iron ore part was decreased gradually from 95 down to 50%. The decreasing was made by 5% in every 6 hours of operation. Application of the mastered technology of the blast furnace No. 2 with the increased share of pellets will enable to stably supply the blast furnaces No. 1, 3 and 4 by iron ore raw materials in the proportion of 30-35% of pellets and 65-70% of sinter.

Serpentinite Magnesium Binders, Based on Technogenic Raw Materials

2021 ◽  
Vol 316 ◽  
pp. 1050-1054
Author(s):  
V.N. Zyryanova ◽  
E.V. Lytkina ◽  
A.P. Ochur-Ool
Keyword(s):  
Mechanical Strength ◽  
Water Resistance ◽  
Raw Materials ◽  
Raw Material ◽  
Material Base ◽  
Hardening Process ◽  
Dispersed System ◽  
Technogenic Raw Materials

Increasing water resistance and mechanical strength of hardening magnesian binders’ products can be achieved by introducing microfillings into a hardening dispersed system. It is shown that serpentine provides an increase strength and water resistance in hydration and hardening process, being as a structure-forming component, it intensifies this process. It allows expanding the raw material base for the production of magnesia binders for construction purposes.

Technological aspects of alcohol distillates production from non-traditional sugar-raw materials

2021 ◽  
Vol 9 (16) ◽  
pp. 90-97
Author(s):  
Kateryna Danilova ◽  
◽  
Oksana Zavarzina ◽  
Keyword(s):  
Raw Materials ◽  
Biologically Active ◽  
Raw Material ◽  
Material Base ◽  
Growth Substances ◽  
Technological Properties ◽  
Actual Problem ◽  
Cane Molasses ◽  
Yeast Biomass ◽  
Nitrogen Phosphorus

An actual problem of the alcohol industry development is the expansion of the raw material base through the use of new, cheaper types of carbohydrate sources. Recently, glucose-fructose syrup has been of increasing interest to producers of ethanol. Among the producers of craft drinks, in particular rum-based drinks, cane molasses is in increasing demand. The article presents the technological aspects of the fermentation process of nonconventional sugar-containing raw materials on the example of glucose-fructose syrup and cane molasses in ethanol by different yeast strains. It is determined that glucose-fructose syrup and cane molasses are raw materials depleted of nitrogen, phosphorus and growth substances necessary for the yeast activity. To improve the technological properties of raw materials in the molasses, nitrogen, phosphorus nutrition and corn extract as a growth substance shall be added to a mash. Glucose-fructose syrup is of pH 3.68 and of acidity 0.12, which negatively affects the fermentation. It is established that in order to create optimal living conditions for yeast, it is necessary to add substances to the glucose-fructose syrup that will contribute to the safety of development and prevent the pH 3.5. It was determined that the alcohol yield from 1 ton of glucose-fructose syrup is 31.0 dal, from 1 ton of cane molasses is 24.0 dal on the yeast 46ED and 22 dal on the TegaYeast without the use of growth substances and vitamins necessary for the reproduction of yeast biomass. Under conditions of improving the technological properties of the mash from the glucose-fructose syrup and cane molasses by adding biologically active substances promoting the synthesis of yeast biomass, the ethanol content in the fermented mashes increases up to 11.9 12% vol.

scholarly journals Antimicrobial Activity and Polyphenol Profiles of Hydroalcoholic Extracts of Thymus rasitatus Klokov and Thymus eremita Klokov

2021 ◽  
Vol 9 (A) ◽  
pp. 313-317
Author(s):  
Svetlana Ivasenko ◽  
Ainur Zhumabekova ◽  
Agnieszka Ludwiczuk ◽  
Krystyna Skalicka–Wozniak ◽  
Alexandr Marchenko ◽  
...  
Keyword(s):  
Antimicrobial Activity ◽  
Chromatographic Analysis ◽  
Antimicrobial Agents ◽  
Raw Materials ◽  
Wide Spectrum ◽  
Raw Material ◽  
Thymus Vulgaris ◽  
Material Base ◽  
Ultrasound Assisted Extraction ◽  
Ethanol Extracts

BACKGROUND: A possible reduction in stocks of medicinal plant raw materials of Thymus serpyllum L. and Thymus vulgaris L. leads to the need to expand the raw material base of the official medicinal plants with using of endemic species of the flora of Kazakhstan, in particular, Thymus rasitatus Klokov, and Thymus eremita Klokov. AIM: The aim of the study was to study the possibility of using 70% ethanol extracts of T. rasitatus and T. eremita as antimicrobial agents. MATERIALS AND METHODS: The aerial parts of T. rasitatus and T. eremita were extracted with 70% ethanol using ultrasound assisted extraction. The qualitative and quantitative analyses of the 70% ethanol extracts were determined using the liquid chromatography-detection-ESI-mass spectrometry-(MS)/MS technique. The study of the antimicrobial activity of these extracts was performed for eight strains of Gram-positive bacteria, six strains of Gram-negative bacteria, and four cultures of fungi. RESULTS: Chromatographic analysis of hydroalcoholic extracts of both investigated Thymus species showed very similar phenolic compounds composition. In both cases, the major components are luteolin-7-O-glucoside and rosmarinic acid. About 70% ethanol extracts of T. rasitatus and T. eremita have a broad spectrum of antimicrobial activity, exhibit the bactericidal or bacteriostatic activity against all tested bacteria and fungi at concentration range of 0.0195–20 mg/ml, but differ in their potency against tested strains of microorganisms. CONCLUSION: About 70% ethanol extracts of T. rasitatus and T. eremita, endemic plants in the flora of Kazakhstan, can be considered as potential drugs with a wide spectrum of antimicrobial activity. The results of chromatographic analysis could be used for drug standardization.

scholarly journals Physical and Chemical Fundamentals and Technical Solutions for Recovery of Non-ferrous and Rare Metals from Industrial Wastes

2020 ◽  
Author(s):  
P.A. Kozlov ◽  
A.M. Panshin ◽  
L.I. Leontiev
Keyword(s):  
Russian Federation ◽  
Raw Materials ◽  
Block Diagram ◽  
Industrial Wastes ◽  
Raw Material ◽  
Material Base ◽  
Waelz Process ◽  
Zinc Cadmium ◽  
The Russian Federation ◽  
Increasing Demand

The increasing demand for zinc and a range of zinc-related metals (for example: lead; indium; tin; cadmium; and copper) in the Russian Federation cannot be satisfied by the existing production plants due to the lack of raw materials. At the same time, ferrous and non-ferrous metallurgy and the chemical industry have accumulated hundreds of millions of tons of zinc wastes (falling into the hazard categories 2 to 4), the processing of which could not only make up the raw material base, but also improve the environmental situation. In the world, over 85% of ferrous dust is recycled using the Waelz process. The Waeltz process is used for distilling separation of elements under reducing conditions. In this study, a block diagram for production of the following elements from industrial wastes is proposed: zinc, cadmium and indium in form of massive metals; zinc and indium in the form of fine powders; and clinker as a raw material for cement production. The technical and scientific details of this new process have been patented in the Russian Federation and abroad. For the first time, the following operations have been implemented with the use of large-sized Waelz kilns: vapour-oxidized Waeltz treatment of polymetallic wastes; recycling of heat from gases and solid products with generation of process fumes; and implementation of alternative flux (dolomite) and alternative fuel (petroleum coke). Keywords: Waelz process, industrial wastes, heat recycling, vapour-oxidized Waelz processing

scholarly journals The Socioeconomic Bases of Biofuels Production Business at the Organizational Level

2021 ◽  
Vol 5 (520) ◽  
pp. 175-187
Author(s):  
R. V. Lohosha ◽  
◽  
I. A. Semchuk ◽  
Keyword(s):  
Business Processes ◽  
Raw Materials ◽  
Biofuel Production ◽  
Organizational Level ◽  
Technological Support ◽  
Agricultural Enterprises ◽  
Efficient Management ◽  
The Matrix ◽  
Scientific Substantiation ◽  
The One

The article is aimed at defining the priorities for the development of the biofuel market in Ukraine to ensure the energy security of the country and satisfy the country’s energy needs. Prospects for the bioenergy sector of the economy in the world will be determined primarily by the optimization of national policies in the matrix of multifarious criteria. The place of the Ukrainian model is highly likely to be determined, on the one hand, by the development of the national market, on the other hand, by the production of raw materials for world biofuel markets. At the same time, this market and production in Ukraine remains only a potentially promising model that requires a scientific substantiation for its efficiency. As a result of the study, it is specified that the bioenergy industry has serious limitations and problems of economic nature that require scientific substantiation. After analyzing the limitations and prospects of the industry development in Ukraine at the level of agricultural enterprises that could deploy biofuel production, it should be emphasized that: 1) there is currently no biofuel market in Ukraine: there is no significant production, hence the proposal still remains unformed; there are no agents (firms, enterprises) of the market that would form the established demand; the necessary norms, institutions, mechanisms of the representative market have not been developed; 2) there is no successful experience of such a business both in Ukraine in general and in agricultural enterprises in particular. From here, as well as taking into account the above-mentioned aspects, the attractiveness of this business, including investment, needs to be justified. Enterprises of this group will face funding problems, as well as technical and technological support problems. Therefore, special careful economic substantiation of the market efficiency model and business processes is required; 3) because of these reasons, the task of scientific substantiation of the model of efficient management of this business becomes highly topical.

Sign in / Sign up

Export Citation Format

Share Document