Evaluation of Nanofluids for Selected Malaysian Oilfields with Limited Cores: A Rapid Test Approach

2021 ◽  
Author(s):  
Luky Hendraningrat ◽  
Saeed Majidaie ◽  
Che Abdul Nasser Bakri Bin Che Mamat ◽  
Norzafirah Binti Razali ◽  
Chee Sheau Chien ◽  
...  

Abstract As an emerging technology, nanoparticle offers advanced benefits to be used as a novel improved oil recovery method. The nanoparticle has a much smaller size than pores of rock that can penetrate deeper in the reservoir and it is easily functionalized to change the wettability of rocks. However, the synthesize and screening process of nanofluids will be a laborious task and need a long-term period and numerous cores at rock-fluid tests. It would be a big issue if the research period is short and native cores are limited or even unavailable. This paper presents a rapid test approach to evaluate nanofluids for a Malaysian oilfield with limited cores. Numerous nanofluids: nanopolymer and nanosurfactants, were evaluated using crude oil from a selected oilfield. Rapid measurement tests are proposed based on a parallel bottom-up approach from contact angle, thermal stability, and interfacial tension (IFT) measurement with at reservoir temperature conditions. Glass plate was initially used as the solid media for optimization of nanofluids concentration. Once this is ascertained then it can be used for further analysis on limited native core slab. Rock mineralogy, fluid rheology, and characterization were also determined. The fluid-fluid and rock-fluid measurements were repeated to ensure consistency of results and to estimate deviation in measurements. Based on a rapid test approach, it was observed that the screening process only took several days instead of months to select suitable nanofluids and glass plates that could be used in the screening process to reduce consuming cores for oilfields with a limited core. A series of glass plate experiment showed consistent results with the core slab. It was observed that dynamic optical contact angle using can achieve steady conditions for approximately half an hour. It was also observed that both the glass plate and replicate core slab show consistency of wettability alteration trend and benefits of multiple runs can observe how big the deviation of measurement. As predicted, all nanofluids can alter the rock wetting behavior. A decreasing contact angle showed that the solid media was rendered to be more water-wet, which implies better oil displacement due to residual oil saturation reduction. Surfactant grafted nanoparticles have given marginal effect on IFT reduction at a certain concentration and achieved steady in less than an hour. These results showed the most potential rapidly for further analysis on coreflooding experiments. The rapid test approach can evaluate and screen nanofluids for detailed coreflooding experiments. This approach readily applies for uncored or limited cores and limited research period.

2021 ◽  
Author(s):  
Xu-Guang Song ◽  
Ming-Wei Zhao ◽  
Cai-Li Dai ◽  
Xin-Ke Wang ◽  
Wen-Jiao Lv

AbstractThe ultra-low permeability reservoir is regarded as an important energy source for oil and gas resource development and is attracting more and more attention. In this work, the active silica nanofluids were prepared by modified active silica nanoparticles and surfactant BSSB-12. The dispersion stability tests showed that the hydraulic radius of nanofluids was 58.59 nm and the zeta potential was − 48.39 mV. The active nanofluids can simultaneously regulate liquid–liquid interface and solid–liquid interface. The nanofluids can reduce the oil/water interfacial tension (IFT) from 23.5 to 6.7 mN/m, and the oil/water/solid contact angle was altered from 42° to 145°. The spontaneous imbibition tests showed that the oil recovery of 0.1 wt% active nanofluids was 20.5% and 8.5% higher than that of 3 wt% NaCl solution and 0.1 wt% BSSB-12 solution. Finally, the effects of nanofluids on dynamic contact angle, dynamic interfacial tension and moduli were studied from the adsorption behavior of nanofluids at solid–liquid and liquid–liquid interface. The oil detaching and transporting are completed by synergistic effect of wettability alteration and interfacial tension reduction. The findings of this study can help in better understanding of active nanofluids for EOR in ultra-low permeability reservoirs.


2021 ◽  
Author(s):  
Rukaun Chai ◽  
Yuetian Liu ◽  
Qianjun Liu ◽  
Xuan He ◽  
Pingtian Fan

Abstract Unconventional reservoir plays an increasingly important role in the world energy system, but its recovery is always quite low. Therefore, the economic and effective enhanced oil recovery (EOR) technology is urgently required. Moreover, with the aggravation of greenhouse effect, carbon neutrality has become the human consensus. How to sequestrate CO2 more economically and effectively has aroused wide concerns. Carbon Capture, Utilization and Storage (CCUS)-EOR is a win-win technology, which can not only enhance oil recovery but also increase CO2 sequestration efficiency. However, current CCUS-EOR technologies usually face serious gas channeling which finally result in the poor performance on both EOR and CCUS. This study introduced CO2 electrochemical conversion into CCUS-EOR, which successively combines CO2 electrochemical reduction and crude oil electrocatalytic cracking both achieves EOR and CCUS. In this study, multiscale experiments were conducted to study the effect and mechanism of CO2 electrochemical reduction for CCUS-EOR. Firstly, the catalyst and catalytic electrode were synthetized and then were characterized by using scanning electron microscope (SEM) & energy dispersive X-ray spectroscopy (EDS) and X-ray photoelectron spectroscopy (XPS). Then, electrolysis experiment & liquid-state nuclear magnetic resonance (1H NMR) experiments were implemented to study the mechanism of CO2 electrochemical reduction. And electrolysis experiment & gas chromatography (GC) & viscosity & density experiments were used to investigate the mechanism of crude oil electrocatalytic cracking. Finally, contact angle and coreflooding experiments were respectively conducted to study the effect of the proposed technology on wettability and CCUS-EOR. SEM & EDS & XPS results confirmed that the high pure SnO2 nanoparticles with the hierarchical, porous structure, and the large surface area were synthetized. Electrolysis & 1H NMR experiment showed that CO2 has converted into formate with the catalysis of SnO2 nanoparticles. Electrolysis & GC & Density & Viscosity experiments indicated that the crude oil was electrocatalytically cracked into the light components (<C20) from the heavy components (C21∼C37). As voltage increases from 2.0V to 7.0V, the intensity of CO2 electrocchemical reduction and crude oil electrocatalytic cracking enhances to maximum at 3.5V (i.e., formate concentration reaches 6.45mmol/L and carbon peak decreases from C17 to C15) and then weakens. Contact angle results indicated that CO2 electrochemical reduction and crude oil electocatalytic cracking work jointly to promote wettability alteration. Thereof, CO2 electrochemical reduction effect is dominant. Coreflooding results indicated that CO2 electrochemical reduction technology has great potential on EOR and CCUS. With the SnO2 catalytic electrode at optimal voltage (3.5V), the additional recovery reaches 9.2% and CO2 sequestration efficiency is as high as 72.07%. This paper introduced CO2 electrochemical conversion into CCUS-EOR, which successfully combines CO2 electrochemical reduction and crude oil electrocatalytic cracking into one technology. It shows great potential on CCUS-EOR and more studies are required to reveal its in-depth mechanisms.


2021 ◽  
Author(s):  
Mohamed Ibrahim Mohamed ◽  
Vladimir Alvarado

Abstract A large percentage of petroleum reserves are located in carbonate reservoirs, which can be divided into limestone, chalk and dolomite. Roughly the oil recovery from carbonates is below the 30% due to the strong oil wetness, low permeability, abundance of natural fractures, and inhomogeneous rock properties Austad (2013). Injection of adjusted brine chemistry into carbonate reservoirs has been reported to increase oil recovery by 5-30% of the original oil in place in field tests and core flooding experiments. Previous studies have shown that adjusted waterflooding recovery in carbonate reservoirs is dependent on the composition and ionic strength of the injection brine (Morrow et al. 1998; Zhang 2005). Many research works have focused on the role of the brine composition in altering the initial wettability state of carbonate rock, which is usually intermediate- to oil-wet. Crude oils contain carboxyl group, -COOH, that can be found in the resin and asphaltenes fractions. The negatively charged carboxyl group, -COOH bond very strongly with the positively charged, sites on the carbonate surface. The carbonate surface, which is positively charged is believed to adsorb the SO42− that is negatively charged. On the other side cations Ca2+ and Mg2+ bind to the negatively charged carboxylic group and release it from the surface. In this study we use a closed system geochemical model to study the effect of the surface-charge dominant species; Ca2+, Mg2+ and SO42− on the carbonate surfaces at 80 °C. The proposed geochemical interactions can possibly lead to a change in the surface charge, altering wettability of the rock by exchanging ions/cations. Brines with various concentrations of Mg2+ and SO42− were prepared in the lab and contact angle between carbonate substrate and crude oil was measured using a rising/captive bubble tensiometer at 80 °C. The composition of the carbonate system was collected from previous literature review and the composition of adjusted brines was used to build a surface sorption database to develop a geochemical model. This model is focused on identifying the reaction paths and the surface behavior that may represent the real system. Changes in carbonate surface wettability were further evaluated using a series of contact angle experiments. Experimental observations and modeling results are concordant and imply that SO42− ions may alter the wettability of carbonate surface at high temperature.


2020 ◽  
Vol 10 (5) ◽  
pp. 6328-6342 ◽  

Low salinity water in the oil reservoirs changes the wettability and increases the oil recovery factor. In sandstone reservoirs, the sand production occurs or intensifies with wettability alteration due to low salinity water injection. In any case, sand production should be stopped and there are many ways to prevent sand production. By modifying the composition of low salinity water, it can be adapted to be more compatible with the reservoir rock and formation water, which has the least formation damage. By eliminating magnesium and calcium ions, smart soft water (SSW) is created which is economically suitable for injection into the reservoirs. By stabilizing the nanoparticles in SSW, nanofluids can be prepared which with injection into the sandstones reservoir increase the oil recovery, change the wettability and increase the rock strength. In this present, SSW composition was determined by compatibility testing, and the SiO2 nanoparticle with 1000 ppm concentration was stabilized in SSW. Eight thin sections were oil wetted by using normal heptane solution and different molars of stearic acid and two thin sections were considered as base thin sections to compare the effect of wettability alteration on sand production. Thin sections were immersed in SSW and Nanofluid, the amount of contact angle and sand production were measured in both cases. The amount of sand produced and the contact angle in SSW was higher than the Nanofluid. The silica nanoparticles reduced the contact angle (more water wetting) and by sitting between the sand particles, more than 40%, it reduced sand production.


2021 ◽  
Author(s):  
Ilgar Baghishov ◽  
Gayan A. Abeykoon ◽  
Mingyuan Wang ◽  
Francisco J. Argüelles Vivas ◽  
Ryosuke Okuno

Abstract Previous studies indicated the efficacy of the simplest amino acid, glycine, as an aqueous additive for enhanced water imbibition in carbonate reservoirs. The objective of this research was to investigate the importance of the amino group of glycine in its enhanced water imbibition. To this end, glycine was compared with two carboxylates (acetate and formate) with/without adding hydrogen chloride (HCl) for adjusting the solution pH. Note that the amino group is the only difference between glycine and acetate. Contact-angle experiments on calcite were carried out at 347 K and atmospheric pressure with 68000-ppm reservoir brine (RB), and 4 different concentrations of glycine, acetate, and formate solutions in RB. To test the hypothesis that calcite dissolution is one of the main mechanisms in wettability alteration by glycine, we performed another set of contact angle experiments by adding HCl to brine, acetate, and formate solutions. HCl was added to match the pH of the glycine solution at the same concentration. We also performed imbibition tests with Texas Cream Limestone cores at 347 K with brine, glycine, acetate, and formate solutions (with and without HCl) in RB at 5.0 wt%. Contact-angle results indicated that glycine changed calcite's wettability from oil-wet to water-wet (45°). However, acetate solution was not able to change the wettability to water-wet; and formate moderately decreased the contact angle to 80°. The pH level increased from 6.1 to 7.6 after the contact angle experiment in glycine solution, indicating the consumption of hydrogen ions due to calcite dissolution. The levels of pH in formate and acetate solutions, however, decreased from 8.4 to 7.8. The acidity of glycine above its isoelectric point arises from the deprotonation of the carboxyl group. Imbibition tests with carbonate cores supported the observations from the contact-angle experiments. The oil recovery was 31% for glycine solution, 20% for RB, 21% for formate solution, and 19% for acetate solution. This re-confirmed the effectiveness of glycine as an additive to improve the oil recovery from carbonates. An additional set of imbibition tests revealed that acetate at the pH reduced to the same level as glycine was still not able to recover as much oil as glycine. This showed that glycine recovered oil not only because of the calcite dissolution and the carboxyl group, but also because of the amino group. It is hypothesized that the amino group with its electron donor ability creates a chelation effect that makes glycine entropically more favorable to get attached to the calcite surface than acetate. Another important result is that the formate solution at an adjusted pH resulted in a greater oil recovery than RB or RB at the same pH. This indicates that there is an optimal pH for the carboxyl group to be effective in wettability alteration as also indicated by the pH change during the contact-angle experiment.


Author(s):  
Leonardo Fonseca Reginato ◽  
Lucas Gomes Pedroni ◽  
André Luiz Martins Compan ◽  
Rodrigo Skinner ◽  
Marcio Augusto Sampaio

Engineered Water Injection (EWI) has been increasingly tested and applied to enhance fluid displacement in reservoirs. The modification of ionic concentration provides interactions with the pore wall, which facilitates the oil mobility. This mechanism in carbonates alters the natural rock wettability being quite an attractive recovery method. Currently, numerical simulation with this injection method remains limited to simplified models based on experimental data. Therefore, this study uses Artificial Neural Networks (ANN) learnability to incorporate the analytical correlation between the ionic combination and the relative permeability (Kr), which depicts the wettability alteration. The ionic composition in the injection system of a Brazilian Pre-Salt benchmark is optimized to maximize the Net Present Value (NPV) of the field. The optimization results indicate the EWI to be the most profitable method for the cases tested. EWI also increased oil recovery by about 8.7% with the same injected amount and reduced the accumulated water production around 52%, compared to the common water injection.


2019 ◽  
Vol 10 (4) ◽  
pp. 1551-1563 ◽  
Author(s):  
Siamak Najimi ◽  
Iman Nowrouzi ◽  
Abbas Khaksar Manshad ◽  
Amir H. Mohammadi

Abstract Surfactants are used in the process of chemical water injection to reduce interfacial tension of water and oil and consequently decrease the capillary pressure in the reservoir. However, other mechanisms such as altering the wettability of the reservoir rock, creating foam and forming a stable emulsion are also other mechanisms of the surfactants flooding. In this study, the effects of three commercially available surfactants, namely AN-120, NX-1510 and TR-880, in different concentrations on interfacial tension of water and oil, the wettability of the reservoir rock and, ultimately, the increase in oil recovery based on pendant drop experiments, contact angle and carbonate core flooding have been investigated. The effects of concentration, temperature, pressure and salinity on the performances of these surfactants have also been shown. The results, in addition to confirming the capability of the surfactants to reduce interfacial tension and altering the wettability to hydrophilicity, show that the TR-880 has the better ability to reduce interfacial tension than AN-120 and NX-1510, and in the alteration of wettability the smallest contact angle was obtained by dissolving 1000 ppm of surfactant NX-1510. Also, the results of interfacial tension tests confirm the better performances of these surfactants in formation salinity and high salinity. Additionally, a total of 72% recovery was achieved with a secondary saline water flooding and flooding with a 1000 ppm of TR-880 surfactant.


2013 ◽  
Vol 868 ◽  
pp. 664-668
Author(s):  
Zi Yuan Qi ◽  
Ye Fei Wang ◽  
Xiao Li Xu

Surfactant imbibition experiments were carried out with four surfactants and effects of interfacial tension and surface wettability on oil recovery were studied. A convenient imbibition process with quartz sands was used, and the experimental results suggest that anionic and non-ionic surfactants have higher oil recovery than cationic surfactant, and the sand surface wettability plays an important role in influencing oil recovery during spontaneous imbibition. Altering the wettability of oil sand surface from oil-wet to water-wet can enhance the oil recovery of imbibition process. The maximum ultimate imbibition recovery appeared in the area where both contact angle and interfacial tension were low.


SPE Journal ◽  
2020 ◽  
Vol 25 (04) ◽  
pp. 1884-1894
Author(s):  
Zuoli Li ◽  
Subhash Ayirala ◽  
Rubia Mariath ◽  
Abdulkareem AlSofi ◽  
Zhenghe Xu ◽  
...  

Summary Polymer enhances the volumetric sweep efficiency through the increased viscosity of injection water and subsequently results in enhanced oil recovery. Most of the reported experimental studies focused on only evaluating polymer viscosifying characteristics and their associated significance for achieving adequate mobility control in porous media. The microscale effects of polymer on wettability alteration in carbonates are rarely studied. In this experimental investigation, the wettability of carbonates in the presence of polymer was measured using contact angle tests. In addition, the adhesion force between carbonate and crude oil droplets in polymer solutions was determined using a custom-designed integrated thin-film drainage apparatus equipped with a bimorph sensor. The liberation kinetics of crude oil from carbonate surfaces were also measured by an optical microscope-based liberation cell to understand the wettability alteration effects on oil recovery. All the experiments, except the adhesion force, which was measured at room temperature due to the restriction of bimorph sensor, were conducted at both ambient and elevated temperatures (70°C) using a sulfonated polyacrylamide polymer (SPAM) (at 500 and 700 ppm) in high-salinity injection water. Deionized (DI) water was used as a baseline to provide a representative comparison with the high-salinity brine. The contact angles of crude oil droplets on a carbonate surface were highest in DI water and decreased in brine. The addition of polymer decreased the contact angle further, with higher concentrations of polymer resulting in a lower contact angle. The adhesion force between crude oil and carbonate showed good agreement with contact angle data, and the oil adhesion was smallest on the carbonate surface in the presence of polymer. The crude oil liberation from the carbonate surface by flooding with brine and polymer was found to be more efficient at elevated temperature than at ambient temperature, consistent with lower contact angles measured in these aqueous solutions at high temperature. The equilibrium oil liberation degree with polymer solutions increased by more than two times when the temperature was increased from 23 to 70°C. The higher liberation degree obtained with polymer solutions also correlated well with the lowest adhesion force measured between crude oil and carbonate in the presence of polymer. These consistent results obtained from different experimental techniques indicated that the oil recovery improvements observed with polymer in dynamic liberation tests are not only related to the increase in water viscosity but are also due to favorable changes in wettability as inferred from both contact angle and adhesion force measurements. This experimental study, for the first time, characterized the microscale effects of polymer on wettability alteration and crude oil liberation in carbonates. The favorable effect of polymer on wettability alteration in carbonates revealed from this study has not been reported in the literature, and it can become a novel addition to the existing knowledge.


2016 ◽  
Vol 864 ◽  
pp. 194-198 ◽  
Author(s):  
Mohd Shahrizan Moslan ◽  
Wan Rosli Wan Sulaiman ◽  
Abdul Razak Ismail ◽  
Mohd Zaidi Jaafar ◽  
Issham Ismail

Wettability alteration of rock by surfactant has been considered as feasible method for recovery of oil reservoirs by modifying the wettability of rock surface from oil-wet to water-wet condition. The impact of surfactant can be enhanced by adding nanoparticles. Cationic surfactant performed well in carbonate rock by forming ion pairs between cationic head and acidic component of the crude. Meanwhile, nanoparticles will form continuous wedge film between the liquid and solid surface. In this paper, Al2O3 and ZrO2 nanoparticles were used as enhanced oil recovery (EOR) agents. The impact of these two nanoparticles on contact angle and interfacial tension was studied. Besides that, adsorption Cetyltrimethylammonium Bromide (CTAB) surfactant on rock surface was also investigated. The results show a significant change in water-oil contact angle after application of surfactant and nanoparticles. Initial water-oil contact angle for 6 dolomites demonstrate oil-wet condition. Then, the dolomites were submerged in prepared solution for 48 hours. The result shows that, dolomites 2, 5 and 6 changes drastically to more water-wet condition with contact angle 56°, 40° and 47° respectively. For surfactant adsorption, the adsorption is very fast at the beginning. The adsorption rate after 5 minutes was 50 mg/g and after 60 minutes the adsorption rate was 310 mg/g. The adsorption rate slowed down after 60 minutes and after 180 minutes the adsorption rate was 315 mg/g in which the rate of adsorption achieve equilibrium. Nanoparticles retention test and Zeta potential shows that Al2O3 is more stable than ZrO2. The results for interfacial tension (IFT) also show a significant reduction. The IFT value reduces from 8.46 mN/m to 1.65 mN/m and 1.85 mN/m after the application of Al2O3 and ZrO2 nanofluids respectively


Sign in / Sign up

Export Citation Format

Share Document