scholarly journals Design and Analysis of Chassis of Four-Seater Car

2021 ◽  
Vol 9 (8) ◽  
pp. 1661-1668
Author(s):  
Murli Jha
Keyword(s):  
Structural Analysis ◽  
Electric Vehicle ◽  
Static Analysis ◽  
Calculated Result ◽  
Ansys Software ◽  
Space Frame ◽  
Suitable Material ◽  
Initial Design ◽  
The Difference ◽  
Selection Of

Abstract: The initial dimensions and weight for the vehicle is considered from the Audi A8 vehicle as a reference. The specifications for the motor and battery are considered for the Mahindra e2o electric vehicle of similar dimensions. The main objective of this paper is to model and perform static analysis on the chassis of a four-seater car. The initial design for the chassis was a space frame body which is very rigid and had very less deflection. The second and final chassis is a ladder type chassis which is most common chassis type being used in Nepal and India. The difference in deflection between both the chassis type is very less, which is about 0.3235 mm for a reasonable reduction in weight which is about 120 Kg. The simulation part is carried out in ANSYS software. The result is selection of best suitable material for chassis on the basis of ANSYS and theoretically calculated result. Keywords: Chassis, Structural Analysis, Optimization, Four seater car

scholarly journals Pendidikan multikultural untuk membangun bangsa yang nasionalis religius

2016 ◽  
Vol 13 (1) ◽  
Author(s):  
R. Ibnu Ambarudin
Keyword(s):  
Multicultural Education ◽  
Multicultural Society ◽  
Implementation Phase ◽  
Suitable Material ◽  
The World ◽  
The Future ◽  
The Difference ◽  
Selection Of

Indonesia is a multicultural country, multiethnic, multi-religious, and multi other things spreaded in the world. Therefore, it needs a wise, appropriate, and effective ways to respond so that the steps taken are not slipped ways and consequently endanger the sustainability of the nation in the future. Multicultural education is required by Indonesia to reduce the occurrence of horizontal conflicts between communities, because of differences in culture, ethnicity, customs, and religion is the emphasizing on learning to appreciate differences and not be regarded as causes of fragmentation. This can be done through selection of suitable material or nuanced tolerance towards all humans in the frame of together and do not emphasize the difference because of the spirit of ideology or their respective groups. Conceptually many religions and beliefs in the shades of multicultural are expected to bring about harmonious relationship, but in the implementation phase are still a lot of gaps between the expectation and realization due to some exclusive-uninded people still in multicultural society. 

Reverse Engineering and Structural Analysis of Radiator Fan Blades

2015 ◽  
Vol 786 ◽  
pp. 404-408
Author(s):  
D. Vijayaganapathy ◽  
K. Balasubramanaim
Keyword(s):  
Structural Analysis ◽  
Reverse Engineering ◽  
Static Analysis ◽  
Process Conditions ◽  
Solid Model ◽  
Suitable Material ◽  
Fiber Reinforced Plastic ◽  
Reinforced Plastic ◽  
Different Types ◽  
3D Solid

The function of the fan is to reduce heat in the radiator where hot cooling liquid is circulated. The radiator fan blades are made up of various materials nowadays and the legacy material used is steel. This paper presents the static analysis of the radiator fan and at the outcome we analyze the failure of the entire blade taking into design consideration. The analysis of the radiator fan is executed to different types of materials to check and evaluate the material and process conditions which withstand the dynamic and structural loads. In the paper design of the blade is done through reverse engineering. The static analysis is done using ANSYS where the 3D solid model of the radiator fan is considered for structural analysis. The various loads and properties and applied through the entire length of the radiator fan. The analysis leads us to proposal of suitable material to withstand all the loads. The Fiber Reinforced Plastic (FRP) material is tested and considered.

COMBINATORIAL POLYNOMIALLY COMPUTABLE CHARACTERISTICS OF SUBSTITUTIONS AND THEIR PROPERTIES

2020 ◽  
Vol 7 (2) ◽  
pp. 34-41
Author(s):  
VLADIMIR NIKONOV ◽  
◽  
ANTON ZOBOV ◽  
Keyword(s):  
Mathematical Expectation ◽  
Point Of View ◽  
Small Range ◽  
Computational Point ◽  
Wide Range ◽  
Bijective Function ◽  
The Difference ◽  
Element Base ◽  
Selection Of

The construction and selection of a suitable bijective function, that is, substitution, is now becoming an important applied task, particularly for building block encryption systems. Many articles have suggested using different approaches to determining the quality of substitution, but most of them are highly computationally complex. The solution of this problem will significantly expand the range of methods for constructing and analyzing scheme in information protection systems. The purpose of research is to find easily measurable characteristics of substitutions, allowing to evaluate their quality, and also measures of the proximity of a particular substitutions to a random one, or its distance from it. For this purpose, several characteristics were proposed in this work: difference and polynomial, and their mathematical expectation was found, as well as variance for the difference characteristic. This allows us to make a conclusion about its quality by comparing the result of calculating the characteristic for a particular substitution with the calculated mathematical expectation. From a computational point of view, the thesises of the article are of exceptional interest due to the simplicity of the algorithm for quantifying the quality of bijective function substitutions. By its nature, the operation of calculating the difference characteristic carries out a simple summation of integer terms in a fixed and small range. Such an operation, both in the modern and in the prospective element base, is embedded in the logic of a wide range of functional elements, especially when implementing computational actions in the optical range, or on other carriers related to the field of nanotechnology.

Effect of Inner and Outer Wheels Driving Force Control on Small Electric Vehicle

2020 ◽  
Vol 17 (4) ◽  
pp. 8246-8254
Author(s):  
K. Shibazaki ◽  
H. Nozaki
Keyword(s):  
Control System ◽  
Angular Velocity ◽  
Electric Vehicle ◽  
Force Constant ◽  
Force Control ◽  
Driving Force ◽  
Vehicle Control ◽  
Steering Angle ◽  
Force Control System ◽  
The Difference

In this study, in order to improve steering stability during turning, we devised an inner and outer wheel driving force control system that is based on the steering angle and steering angular velocity, and verified its effectiveness via running tests. In the driving force control system based on steering angle, the inner wheel driving force is weakened in proportion to the steering angle during a turn, and the difference in driving force is applied to the inner and outer wheels by strengthening the outer wheel driving force. In the driving force control (based on steering angular velocity), the value obtained by multiplying the driving force constant and the steering angular velocity,  that differentiates the driver steering input during turning output as the driving force of the inner and outer wheels. By controlling the driving force of the inner and outer wheels, it reduces the maximum steering angle by 40 deg and it became possible to improve the cornering marginal performance and improve the steering stability at the J-turn. In the pylon slalom it reduces the maximum steering angle by 45 deg and it became possible to improve the responsiveness of the vehicle. Control by steering angle is effective during steady turning, while control by steering angular velocity is effective during sharp turning. The inner and outer wheel driving force control are expected to further improve steering stability.

scholarly journals Age-dependency in mortality of Finnish family caregivers: a nationwide register-based study

2020 ◽  
Vol 30 (Supplement_5) ◽  
Author(s):  
T M Mikkola ◽  
H Kautiainen ◽  
M Mänty ◽  
M B von Bonsdorff ◽  
T Kröger ◽  
...  
Keyword(s):  
General Population ◽  
Family Caregivers ◽  
Family Caregiver ◽  
Causes Of Death ◽  
Lower Mortality ◽  
All Cause Mortality ◽  
The Difference ◽  
Caregiver Role ◽  
Selection Of

Abstract Purpose Mortality appears to be lower in family caregivers than in the general population. However, there is lack of knowledge whether the difference in mortality between family caregivers and the general population is dependent on age. The purpose of this study was to analyze all-cause mortality in relation to age in family caregivers and to study their cause-specific mortality using data from multiple Finnish national registers. Methods The data included all individuals, who received family caregiver's allowance in Finland in 2012 (n = 42 256, mean age 67 years, 71% women) and a control population matched for age, sex, and municipality of residence (n = 83 618). Information on dates and causes of death between 2012 and 2017 were obtained from the Finnish Causes of Death Register. Flexible parametric survival modeling and competing risk regression adjusted for socioeconomic status were used. Results The total follow-up time was 717 877 person-years. Family caregivers had lower all-cause mortality than the controls over the follow-up (8.1% vs. 11.6%) both among women (hazard ratio [HR]: 0.64, 95% CI: 0.61-0.68) and men (HR: 0.73, 95% CI: 0.70-0.77). Younger adult caregivers had equal or only slightly lower mortality than their controls, but after age 60, the difference increased markedly resulting in over 10% lower mortality in favor of the caregivers in the oldest age groups. Caregivers had lower mortality for all the causes of death studied, namely cardiovascular, cancer, neurological, external, respiratory, gastrointestinal and dementia than the controls. Of these, the lowest was the risk for dementia (subhazard ratio=0.29, 95%CI: 0.25-0.34). Conclusions Older family caregivers have lower mortality than the age-matched controls from the general population while younger caregivers have similar mortality to their peers. This age-dependent advantage in mortality is likely to reflect selection of healthier individuals into the family caregiver role. Key messages The difference in mortality between family caregivers and the age-matched general population varies considerably with age. Advantage in mortality observed in family caregiver studies is likely to reflect the selection of healthier individuals into the caregiver role, which underestimates the adverse effects of caregiving.

scholarly journals A microfluidic device enabling drug resistance analysis of leukemia cells via coupled dielectrophoretic detection and impedimetric counting

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Yağmur Demircan Yalçın ◽  
Taylan Berkin Töral ◽  
Sertan Sukas ◽  
Ender Yıldırım ◽  
Özge Zorlu ◽  
...  
Keyword(s):  
Drug Resistance ◽  
K562 Cells ◽  
Leukemia Cells ◽  
Drug Resistant ◽  
Wild Type ◽  
Gene Expressions ◽  
Before And After ◽  
The Difference ◽  
Selection Of ◽  
Resistant Cells

AbstractWe report the development of a lab-on-a-chip system, that facilitates coupled dielectrophoretic detection (DEP-D) and impedimetric counting (IM-C), for investigating drug resistance in K562 and CCRF-CEM leukemia cells without (immuno) labeling. Two IM-C units were placed upstream and downstream of the DEP-D unit for enumeration, respectively, before and after the cells were treated in DEP-D unit, where the difference in cell count gave the total number of trapped cells based on their DEP characteristics. Conductivity of the running buffer was matched the conductivity of cytoplasm of wild type K562 and CCRF-CEM cells. Results showed that DEP responses of drug resistant and wild type K562 cells were statistically discriminative (at p = 0.05 level) at 200 mS/m buffer conductivity and at 8.6 MHz working frequency of DEP-D unit. For CCRF-CEM cells, conductivity and frequency values were 160 mS/m and 6.2 MHz, respectively. Our approach enabled discrimination of resistant cells in a group by setting up a threshold provided by the conductivity of running buffer. Subsequent selection of drug resistant cells can be applied to investigate variations in gene expressions and occurrence of mutations related to drug resistance.

scholarly journals Weightage Effect during Back-Calculation of Rock-Mass Quality from the Installed Tunnel Support in Rock-Mass Rating and Tunneling Quality Index System

2019 ◽  
Vol 9 (10) ◽  
pp. 2065 ◽  
Author(s):  
Jonguk Kim ◽  
Hafeezur Rehman ◽  
Wahid Ali ◽  
Abdul Muntaqim Naji ◽  
Hankyu Yoo
Keyword(s):  
Rock Mass ◽  
Quality Index ◽  
Rock Bolt ◽  
Rock Mass Rating ◽  
Rock Mass Quality ◽  
Back Calculation ◽  
The Difference ◽  
Bolt Spacing ◽  
Q System ◽  
Selection Of

In extensively used empirical rock-mass classification systems, the rock-mass rating (RMR) and tunneling quality index (Q) system, rock-mass quality, and tunnel span are used for the selection of rock bolt length and spacing and shotcrete thickness. In both systems, the rock bolt spacing and shotcrete thickness selection are based on the same principle, which is used for the back-calculation of the rock-mass quality. For back-calculation, there is no criterion for the selection of rock-bolt-spacing-based rock-mass quality weightage and shotcrete thickness along with tunnel-span-based rock-mass quality weightage. To determine this weightage effect during the back-calculation, five weightage cases are selected, explained through example, and applied using published data. In the RMR system, the weightage effect is expressed in terms of the difference between the calculated and back-calculated rock-mass quality in the two versions of RMR. In the Q system, the weightage effect is presented in plots of stress reduction factor versus relative block size. The results show that the weightage effect during back-calculation not only depends on the difference in rock-bolt-spacing-based rock-mass quality and shotcrete along with tunnel-span-based rock-mass quality, but also on their corresponding values.

Structural and Static Analysis of the Mechanisms Used in Car Mechanical Jacks

2016 ◽  
Vol 823 ◽  
pp. 277-282
Author(s):  
Viorica Velișcu ◽  
Dan Mesarici ◽  
Păun Antonescu
Keyword(s):  
Structural Analysis ◽  
Static Analysis ◽  
Kinematic Chain ◽  
Gravity Force ◽  
Complex Mechanisms

The paper presents a structural analysis of the complex mechanisms type screw-jack. The mechanism mobilityanalysis using various generally applicable formulas has been performed. A newkinematic scheme of the jack linkage has been proposed. Besides the actuatorscrew, it has a planar kinematic chain with articulated bars. With regard tothis new mechanism, an algorithm for static calculus has been developed, inwhich the automobile gravity force is the main exterior force.

scholarly journals A Robust Rerank Approach for Feature Selection and Its Application to Pooling-Based GWA Studies

2013 ◽  
Vol 2013 ◽  
pp. 1-11 ◽  
Author(s):  
Jia-Rou Liu ◽  
Po-Hsiu Kuo ◽  
Hung Hung
Keyword(s):  
Characteristic Curve ◽  
Real Data ◽  
Tuning Parameter ◽  
Practical Implementation ◽  
Tuning Parameters ◽  
Genome Wide ◽  
Feature Based ◽  
The Difference ◽  
Gwa Studies ◽  
Selection Of

Large-p-small-ndatasets are commonly encountered in modern biomedical studies. To detect the difference between two groups, conventional methods would fail to apply due to the instability in estimating variances int-test and a high proportion of tied values in AUC (area under the receiver operating characteristic curve) estimates. The significance analysis of microarrays (SAM) may also not be satisfactory, since its performance is sensitive to the tuning parameter, and its selection is not straightforward. In this work, we propose a robust rerank approach to overcome the above-mentioned diffculties. In particular, we obtain a rank-based statistic for each feature based on the concept of “rank-over-variable.” Techniques of “random subset” and “rerank” are then iteratively applied to rank features, and the leading features will be selected for further studies. The proposed re-rank approach is especially applicable for large-p-small-ndatasets. Moreover, it is insensitive to the selection of tuning parameters, which is an appealing property for practical implementation. Simulation studies and real data analysis of pooling-based genome wide association (GWA) studies demonstrate the usefulness of our method.

Sign in / Sign up

Export Citation Format

Share Document