Digital mapping aerial camera – a measuring instrument

2018 ◽  
Vol 934 (4) ◽  
pp. 40-45 ◽  
Author(s):  
S.A. Kadnichanskiy ◽  
S.S. Nekhin ◽  
A.I. Spiridonov
Keyword(s):  
Coordinate System ◽  
Nodal Point ◽  
Image Sensor ◽  
Measurement Range ◽  
Measuring Instrument ◽  
Direction Vector ◽  
Interest Points ◽  
Frame Size ◽  
The Matrix ◽  
The Difference

The difference between the topographic digital aerial cameras and the analogue ones are analyzed. The first one allows considering a digital aerial camera as a means of measurement. A regular rectangular grid of pixels of digital aerial cameras image sensor is a two-dimensional scale with divisions equal to the physical size of the pixel. It allows determining the position of interest points of the image in the coordinate system of a matrix of pixels, the axis of which is directed along rows and columns of the matrix. Wherein the measured value for aerial cameras, should be considered as the coordinates of the vector pointing from the perspective center to the point of interest in the coordinate system of aerial cameras, the beginning of which is located at the front nodal point of the lens, and the Sz axis is directed along the principal ray. Exactly they are directly used in the solutions of photogrammetric tasks for determination of coordinates of the locality object point. The accuracy of the result of determining the coordinates depends on the accuracy of the coordinates of a direction vector and the accuracy of the exterior orientation parameters of aerial cameras (the image). Metrological characteristics of digital topographic aerial cameras should be considered measurement range (the frame size in pixels and pixel size) and the error of a measuring instrument (the error of the coordinates of a direction vector) as the accuracy characteristics and the parameters of calibration of aerial cameras, allowing to determine the measured values according to indications of measurements with estimates of the errors of the calibration parameters.

Tem analysis of multiple-energy arsenic implanted and Rta'd silicon

1987 ◽  
Vol 45 ◽  
pp. 246-247
Author(s):  
R.A. Herring
Keyword(s):  
Device Fabrication ◽  
High Concentration ◽  
Tem Analysis ◽  
Defect Clusters ◽  
High Fluences ◽  
Small Defect ◽  
Before And After ◽  
The Matrix ◽  
The Difference ◽  
Factor Type

Rapid thermal annealing (RTA) of ion-implanted Si is important for device fabrication. The defect structures of 2.5, 4.0, and 6.0 MeV As-implanted silicon irradiated to fluences of 2E14, 4E14, and 6E14, respectively, have been analyzed by electron diffraction both before and after RTA at 1100°C for 10 seconds. At such high fluences and energies the implanted As ions change the Si from crystalline to amorphous. Three distinct amorphous regions emerge due to the three implantation energies used (Fig. 1). The amorphous regions are separated from each other by crystalline Si (marked L1, L2, and L3 in Fig. 1) which contains a high concentration of small defect clusters. The small defect clusters were similar to what had been determined earlier as being amorphous zones since their contrast was principally of the structure-factor type that arises due to the difference in extinction distance between the matrix and damage regions.

Development of Prolonged Delivery of Tramadol and Dissolution Translation by Statistical Data Treatment

2011 ◽  
Vol 4 (1) ◽  
pp. 1331-1337
Author(s):  
P B Parejiya ◽  
B S Barot ◽  
P K Shelat
Keyword(s):  
Drug Release ◽  
Study Data ◽  
Stability Study ◽  
Dissolution Time ◽  
Matrix Tablet ◽  
Burst Effect ◽  
The Matrix ◽  
The Mean ◽  
The Difference ◽  
Dissolution Efficiency

The present study was carried out to fabricate a prolonged design for tramadol using Kollidon SR (Polyvinyl acetate and povidone based matrix retarding polymer). Matrix tablet formulations were prepared by direct compression of Kollidon SR of a varying proportion with a fixed percentage of tramadol. Tablets containing a 1:0.5 (Drug: Kollidon SR) ratio exhibited a rapid rate of drug release with an initial burst effect. Incorporation of more Kollidon SR in the matrix tablet extended the release of drug with subsequent minimization of the burst effect as confirmed by the mean dissolution time, dissolution efficiency and f2 value. Among the formulation batches, a direct relationship was obtained between release rate and the percentage of Kollidon SR used. The formulation showed close resemblance to the commercial product Contramal and compliance with USP specification. The results were explored and explained by the difference of micromeritic characteristics of the polymers and blend of drug with excipients. Insignificant effects of various factors, e.g. pH of dissolution media, ionic strength, speed of paddle were found on the drug release from Kollidon-SR matrix. The formulation followed the Higuchi kinetic model of drug release. Stability study data indicated stable character of Batch T6 after short-term stability study.

Impact of AMSU-A Radiances in a Column Ensemble Kalman Filter

2018 ◽  
Vol 146 (12) ◽  
pp. 3949-3976 ◽  
Author(s):  
Herschel L. Mitchell ◽  
P. L. Houtekamer ◽  
Sylvain Heilliette
Keyword(s):  
Covariance Matrix ◽  
Background Error ◽  
Error Covariance Matrix ◽  
Background Error Covariance ◽  
Error Covariance ◽  
Microwave Sounding Unit ◽  
The Matrix ◽  
Microwave Sounding ◽  
Background Temperature ◽  
The Difference

Abstract A column EnKF, based on the Canadian global EnKF and using the RTTOV radiative transfer (RT) model, is employed to investigate issues relating to the EnKF assimilation of Advanced Microwave Sounding Unit-A (AMSU-A) radiance measurements. Experiments are performed with large and small ensembles, with and without localization. Three different descriptions of background temperature error are considered: 1) using analytical vertical modes and hypothetical spectra, 2) using the vertical modes and spectrum of a covariance matrix obtained from the global EnKF after 2 weeks of cycling, and 3) using the vertical modes and spectrum of the static background error covariance matrix employed to initiate a global data assimilation cycle. It is found that the EnKF performs well in some of the experiments with background error description 1, and yields modest error reductions with background error description 3. However, the EnKF is virtually unable to reduce the background error (even when using a large ensemble) with background error description 2. To analyze these results, the different background error descriptions are viewed through the prism of the RT model by comparing the trace of the matrix , where is the RT model and is the background error covariance matrix. Indeed, this comparison is found to explain the difference in the results obtained, which relates to the degree to which deep modes are, or are not, present in the different background error covariances. The results suggest that, after 2 weeks of cycling, the global EnKF has virtually eliminated all background error structures that can be “seen” by the AMSU-A radiances.

V.—Mr. Harkee and Mr. Debley on the Scandinavian Ice-Sheet

1894 ◽  
Vol 1 (11) ◽  
pp. 496-499
Author(s):  
Henry H. Howorth
Keyword(s):  
Ice Sheet ◽  
Good Effect ◽  
The North ◽  
The Matrix ◽  
Glacier Ice ◽  
Inductive Methods ◽  
The North Sea ◽  
Antarctic Continent ◽  
The Alps ◽  
The Difference

Mr. Deeley tells your readers that he has recently been to the summit of Mont Blanc, and has been studying the difference between névé and glacier ice. This is interesting; but we thought that a great many people had done the same thing during the last hundred years, and we thought that one of them, Forbes, had studied the famous Mountain and the phenomenoninquestion to good effect, not in a casual visit to the Alps, but in the course of many years of patient labour. Among other things we also thought he had shown that in a viscous body like ice, the slope of the upper surface necessary to make it begin to move is the same as the slope which, would be required to induce motion in the ice if its bed were inclined at an angle. He further collected considerable evidence to show what the least angle is upon which ice will begin to move. This is the slope, the least slope, available. It is nothing less than astounding to me that anyone should venture to postulate a Scand in avian ice-sheet in the North Sea until he had considered this necessary factor, and how it would operate.The Scand in avian ice-sheet was, I believe, the invention of Croll, who, sittinginhis arm-chair and endowed with a brilliant imagination, imposed upon sober science this extraordinary postulate. He did not dream of testing it by an examination of the coasts of Norway, or even of Britain, but put it forward apparently as a magnificent deduction. All deductions untested by experiment are dangerous. Thus it came about that the great monster which is said to have come from Norway, goodness knows by what mechanical process, speedily dissolved away on the application of inductive methods. Of course it still maintained its hold upon that section, of geologists who dogmatiseinprint a great deal about the Glacial period before they have ever seen a glacier at work at all; but I am speaking of those who have studied the problem inductively. First Mr. James Geikie, a disciple of Croll, was obliged to confess that this ice-sheet, which is actually said to have advanced as far as the hundred-fathom line in the Atlantic, and there presented a cliff of ice like the Antarctic continent, never can have reached the Faroes, which had an ice-sheet of their own. Next Messrs. Peach and Home were constrained to admit that no traces of it of any kind occur in the Orkneys, or in Eastern Scotland. They still maintained its presence in the Shetlands; however, this was upon evidence which is somewhat extraordinary. I do not mean the evidence as to the direction of the striation, which was so roughly handled by Mr. Milne-Home, but I mean the evidence they adduce that the boulders found on the islands are apparently all local ones, and that, contrary to the deposits of glaciers, they diminish in number as we recede from the matrix whence they were derived.

scholarly journals Measuring a small nonreciprocity of the objects.

2021 ◽  
Vol 2021 (9) ◽  
Author(s):  
E.V. Semyonov ◽  
◽  
N.D. Malyutin ◽  
Keyword(s):  
Noise Immunity ◽  
Measurement Range ◽  
Input And Output ◽  
Relative Value ◽  
The Difference ◽  
Test Impact ◽  
Impact Duration ◽  
Main Factor

In the paper the methods and features of measuring the small nonreciprocity of objects is considered. Several variants of nonreciprocity characteristics are proposed and the variant with most noise immunity is selected. A method of normalizing the chosen nonreciprocity characteristic is considered. It is shown that the exposure of nonreciprocity depends on the probing signals. It is noted that the main factor that limiting the bottom bound of the nonreciprocity measurement range is the difference of the impedances of input and output networks. If a calibration is absent and if the difference between the inductance of the input and output networks is of few tenths of nH, then at a test impact duration of about 50 ps the bottom bound of the nonreciprocity measurement range is of about 1%. The observation of nonreciprocity with a relative value of 3% has been performed experimentally.

scholarly journals PENERAPAN METODE MULTI ATTRIBUTE UTILITY THEORY (MAUT) DALAM PEMETAAN TINGKAT DAMPAK BENCANA BANJIR DI KABUPATEN BANTUL

Telematika ◽  
2020 ◽  
Vol 17 (1) ◽  
pp. 26
Author(s):  
Afif Irfan Abdurrahman ◽  
Bambang Yuwono ◽  
Yuli Fauziah
Keyword(s):  
Utility Theory ◽  
Matrix Multiplication ◽  
Flood Disaster ◽  
Accuracy Rate ◽  
Affected Area ◽  
A Value ◽  
Multi Attribute Utility Theory ◽  
The Matrix ◽  
The Difference ◽  
The Impact

Flood disaster is a dangerous disaster, an event that occurs due to overflow of water resulting in submerged land is called a flood disaster. Almost every year Bantul Regency is affected by floods due to high rainfall. The flood disaster that struck in Bantul Regency made the Bantul District Disaster Management Agency (BPBD) difficult to handle so that it needed a mapping of the level of the impact of the flood disaster to minimize the occurrence of floods and provide information to the public.This study will create a system to map the level of impact of floods in Bantul Regency with a decision support method namely Multi Attribute Utility Theory (MAUT). The MAUT method stage in determining the level of impact of flood disasters through the process of normalization and matrix multiplication. The method helps in determining the areas affected by floods, by managing the Indonesian Disaster Information Data (DIBI). The data managed is data on criteria for the death toll, lost victims, damage to houses, damage to public facilities, and damage to roads. Each criteria data has a value that can be used to determine the level of impact of a flood disaster. The stages for determining the level of impact of a disaster require a weighting calculation process. The results of the weighting process display the scoring value which has a value of 1 = low, 2 = moderate, 3 = high. To assist in determining the affected areas using the matrix normalization and multiplication process the process is the application of the Multi Attribute Utility Theory (MAUT) method.This study resulted in a mapping of the level of impact displayed on google maps. The map view shows the affected area points and the level of impact of the flood disaster in Bantul Regency. The mapping produced from the DIBI data in 2017 produced the highest affected area in the Imogiri sub-district. The results of testing the data can be concluded that the results of this study have an accuracy rate of 95% when compared with the results of the mapping previously carried out by BPBD Bantul Regency. The difference in the level of accuracy is because the criteria data used are not the same as the criteria data used by BPBD in Bantul Regency so that the accuracy rate is 95%.

scholarly journals Tribological properties of friction composites modified by the suspended particles of exhaust flue gases

2019 ◽  
pp. 75-83
Author(s):  
T. A. Akhmetov ◽  
V. K. Merinov ◽  
N. V. Kargapolova
Keyword(s):  
Tribological Properties ◽  
Suspended Particles ◽  
Electric Arc ◽  
Flue Gases ◽  
Spherical Particles ◽  
Dynamic Friction ◽  
Dynamic Friction Coefficient ◽  
Arc Furnaces ◽  
The Matrix ◽  
The Difference

The possibility of using the deposited suspended particles of electric arc furnaces as heat-resistant modifying additives for friction composites is considered. It is shown that the precipitated particles obtained during the smelting of steel of different grades have identical morphology and are a homogeneous mechanical mixture consisting mainly of spherical particles of no more than 1 µm in size.It is established that the composites on the basis of the fluoropolymer, modified by precipitated particles obtained in the smelting of steel of various sizes have different tribological properties. This is due to the difference in the chemical composition of the deposited particles.It was found that the use of deposited particles in composite materials allows to vary the value of the dynamic friction coefficient in a wider range, in particular to obtain higher and stable values, while the wear resistance of modified friction composites is more than 500 times higher than the same index of the matrix polymer – polytetrafluoroethylene.

scholarly journals Investigation of changes in the characteristics of LED matrices of the on-board luminaire during tests in the electrocycling mode.

2021 ◽  
Author(s):  
I.V. Frolov ◽  
◽  
V.A. Sergeev ◽  
A.M. Hodakov ◽  
S.A. Zaytsev ◽  
...  
Keyword(s):  
Leakage Current ◽  
Direct Current ◽  
Coefficient Of Variation ◽  
Convection Heat Transfer ◽  
Voltage Range ◽  
The Matrix ◽  
Operating Current ◽  
In Series ◽  
The Difference ◽  
A Current

The paper presents the results of studies of changes in the characteristics of LED COB matrices of the GW P9LR31.EM - DURIS S 8 type as part of a LED luminaire when tested under the direct current in a continuous mode and in an electrocycling mode. The arrays consist of eight InGaN/GaN LED dies connected in series, coated with a phosphor. Calculation in the Comsol Multiphtsics environment of the temperature field of the luminaire at the rated operating current and free convection heat transfer showed that the maximum overheating of the matrices does not exceed 46 K, and the difference in their temperatures is 2 K. At the same time, the experimental values of the thermal resistances of the matrices of a real lamp vary from 42 to 58 K/W. Before testing, the I-V characteristics of the matrices differ markedly in the level of leakage current in the voltage range from 14 V to 19 V, and the LEDs in the luminaire matrices have a significant spread in the brightness of emission in the microcurrent mode. The degree of this scatter within each matrix was estimated by measuring the luminescence brightness of each die of the matrix and calculating the coefficient of variation γ. It was found that the coefficient of variation of the emission brightness of the COB matrix dies measured at a current of 100 nA strongly correlates with the leakage current. When testing a luminaire under the direct current, the most significant changes in the electrophysical and optical characteristics of COB matrices are observed in the range of microcurrents: the distribution of the emission brightness of the matrix dies at a current of 100 nA becomes more uniform. The greatest changes in matrix characteristics were observed after the first 700 hours of testing, that is, at the running-in stage. At the same time, no correlation was found between the degree of change in the characteristics of the matrices during tests and their thermal resistances.

STIFFNESS OF REINFORCED CONCRETE STRUCTURES UNDER BENDING WITH TRANSVERSE AND LONGITUDINAL FORCES

2021 ◽  
Vol 98 (6) ◽  
pp. 5-19
Author(s):  
VL.I. KOLCHUNOV ◽  
◽  
O.I. AL-HASHIMI ◽  
M.V. PROTCHENKO ◽  
◽  
...  
Keyword(s):  
Reinforced Concrete ◽  
Cross Sections ◽  
Concrete Structures ◽  
Bending Moment ◽  
Reinforced Concrete Structures ◽  
The Matrix ◽  
Local Shear ◽  
The Difference ◽  
Inclined Cracks ◽  
Opening Width

The authors developed a model for single reinforced concrete strips in block wedge and arches between inclined cracks and approximated rectangular cross-sections using small squares in matrix elements. From the analysis of the works of N.I. Karpenko and S.N. Karpenko the "nagel" forces in the longitudinal tensile reinforcement and crack slip , as a function of the opening width and concrete deformations in relation to the cosine of the angle . The experimental " nagel " forces and crack slip dependences for the connection between and in the form of an exponent for the reinforcement deformations and spacing are determined. The forces have been calculated for two to three cross-sections (single composite strips) of reinforced concrete structures. On the bases of accepted hypothesis, a new effect of reinforced concrete and a joint modulus in a strip of composite single local shear zone for the difference of mean relative linear and angular deformations of mutual displacements of concrete (or reinforcement) are developed. The hypothesis allows one to reduce the order of the system of differential equations of Rzhanitsyn and to obtain in each joint the total angular deformations of concrete and the "nagel" effect of reinforcement. The curvature of the composite bars has a relationship from the total bending moment of the bars to the sum of the rigidities. The stiffness physical characteristics of the matrix from the compressed concrete area and the working reinforcement are obtained in a system of equations of equilibrium and deformation, as well as physical equations.

Interaction of elements in carbon-graphite—Al—Mg—Zn—Cu melt system under combined action of temperature and pressure

2021 ◽  
pp. 514-518
Author(s):  
N.Yu. Miroshkin ◽  
V.A. Gulevsky ◽  
S.N. Tsurikhin ◽  
A.I. Bogdanov ◽  
L.M. Gurevich ◽  
...  
Keyword(s):  
Matrix Alloy ◽  
Impregnation Process ◽  
Active Elements ◽  
Cu Alloy ◽  
Inner Surface ◽  
The Matrix ◽  
Combined Action ◽  
Temperature And Pressure ◽  
The Difference ◽  
Titanium Compounds

Redistribution of chemically active elements is established on its inner surface of pores and at the interface with the alloy when impregnating carbon-graphite framework with Al—Mg—Zn—Cu alloy at temperature of 800 °C under pressure of up to 3 MPa. In this case, change in the solubility of melt elements in aluminum is possible as result of the combined action of temperature and pressure in the impregnation process, created due to the difference in the coefficients of thermal and thermal expansion of the matrix alloy, and the material of the impregnation device during impregnation. Titanium compounds are found in the pores filled with metal that are not added to the matrix alloy, but are formed as result of the contact of the matrix alloy melt with the walls of the impregnation device.

Sign in / Sign up

Export Citation Format

Share Document