Properties of Concrete Made from Cupola Furnace Slag and Recycled Construction Aggregates

2021 ◽  
Vol 6 (7) ◽  
pp. 52-61
Author(s):  
A. J. Adese ◽  
O. D. Olajide ◽  
O. A. Olaoyenikan
Keyword(s):  
Compressive Strength ◽  
Partial Replacement ◽  
Test Results ◽  
Microstructural Characteristics ◽  
Complete Replacement ◽  
Cupola Furnace ◽  
Concrete Production ◽  
Hardened Properties ◽  
Increasing Demand ◽  
Furnace Slag

The replacement of traditional constituents of concrete with waste has garnered a lot of interest due to the increasing demand for natural resources used in concrete production. Hence, this study presents the outcome of an experimental investigation on the effect of partial replacement of Ordinary Portland Cement (OPC) at percentage levels of 0% to 25% in steps of 5%, partial and complete replacement of sand and granite in the percentage of 0 to 50 in steps of 10% with cupola slag and recycled construction aggregates. The fresh and hardened properties of concrete such as workability, compressive strength, and microstructural characteristics were assessed. The test results showed a decrease in workability as the percentage replacement of cupola furnace slag (CFS) and recycled construction aggregates (RCA) increases. Concrete produced at 28 days from the partial replacement of cement and sand with cupola slag has an optimum compressive strength of 20.37 N/mm2 at 10% and 22.81 N/mm2 at 20%, resulting in improved strength of 29.4% and 56.82%, respectively when compared with the control. In contrast, granite’s partial replacement with coarse cupola slag and complete replacement of sand and granite gave a lesser compressive strength when compared with the control samples at 7, 14, 28, and 56 days. The porosity of the concrete with optimum compressive strength from each mix was studied using microscopic and image analysis. The result showed that the addition of cupola slag in granulated and fine forms decreases the porosity, hence leading to higher compressive strength. 

scholarly journals Strength Behavior of Mortar Using Slag As Partial Replacement of Cement

1970 ◽  
Vol 3 ◽  
Author(s):  
Md Moinul Islam ◽  
Md Saiful Islam ◽  
Md Aftabur Rahman ◽  
Amrita Das
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Cement Mortar ◽  
Partial Replacement ◽  
Strength Development ◽  
Test Results ◽  
Granulated Blast Furnace Slag ◽  
Strength Behavior ◽  
Furnace Slag ◽  
Curing Age

This paper presents an experimental investigation carried out to study the effects of Ground Granulated Blast Furnace Slag (GGBFS) on strength development of mortar and the optimum use of slag in mortar. Cement was partially replaced with seven percentages (10%, 20%, 30%, 40%, 50%, 60% and 70%) of slag by weight. Ordinary Portland cement (OPC) mortar was also prepared as reference mortar. A total of 400 cube and briquet mortar specimens were cast and compressive as well as tensile strength of the mortar specimens were determined at curing age of 3, 7, 14, 28, 60, 90 and 180 days. Test results show that strength increases with the increase of slag up to an optimum value, beyond which, strength values start decreasing with further addition of slag. Among the seven slag mortars, the optimum amount of cement replacement is about 40%, which provides 19% higher compressive strength and 25% higher tensile strength as compared to OPC mortar. KEY WORDS: Slag; Cement; Mortar; Compressive Strength; Tensile Strength; Hydration. DOI: http://dx.doi.org/10.3329/mist.v3i0.8053

Effect of Microwave Incinerated Rice Husk Ash (MIRHA) on Workability and Compressive Strength of Concrete

2014 ◽  
Vol 935 ◽  
pp. 193-196 ◽  
Author(s):  
Asma Abd Elhsameed ◽  
Nasir Shafiq ◽  
Muhd Fadhil Nuruddin
Keyword(s):  
Compressive Strength ◽  
Rice Husk ◽  
Rice Husk Ash ◽  
Partial Replacement ◽  
Hardened Concrete ◽  
Negative Effects ◽  
Concrete Production ◽  
Hardened Properties ◽  
Compressive Strength Of Concrete ◽  
By Products

Agricultural and industrial by-products are commonly used in concrete production as cement replacement materials (CRMs) or as admixtures to enhance both fresh and hardened properties of concrete as well as to save the environment from the negative effects caused by their disposal. This paper presents some findings on the effect of Microwave Incinerated Rice Husk Ash (MIRHA) on workability and compressive strength of concrete. It was obtained that the inclusion of MIRHA as partial replacement of cement could significantly improve the compressive strength of hardened concrete while reducing the workability of fresh concrete.

Effect of Chopped Basalt Fiber on the Fresh and Hardened Properties of Fly Ash High Strength Concrete

2014 ◽  
Vol 567 ◽  
pp. 381-386 ◽  
Author(s):  
Nasir Shafiq ◽  
Muhd Fadhil Nuruddin ◽  
Ali Elheber Ahmed Elshekh ◽  
Ahmed Fathi Mohamed Salih
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
High Strength Concrete ◽  
Basalt Fiber ◽  
High Strength ◽  
Progressive Increase ◽  
Test Results ◽  
Strength Concrete ◽  
Hardened Properties ◽  
Chopped Basalt Fiber

In order to improve the mechanical properties of high strength concrete, HSC, several studies have been conducted using fly ash, FA. Researchers have made it possible to achieve 100-150MPa high strength concrete. Despite the popularity of this FAHSC, there is a major shortcoming in that it becomes more brittle, resulting in less than 0.1% tensile strain. The main objective of this work was to evaluate the fresh and hardened properties of FAHSC utilizing chopped basalt fiber stands, CBFS, as an internal strengthening addition material. This was achieved through a series of experimental works using a 20% replacement of cement by FA together with various contents of CBFS. Test results of concrete mixes in the fresh state showed no segregation, homogeneousness during the mixing period and workability ranging from 60 to 110 mm. Early and long terms of compressive strength did not show any improvement by using CBFS; in fact, it decreased. This was partially substituted by the effect of FA. Whereas, the split and flexural strengths of FASHC were significantly improved with increasing the content of CBFS as well as the percentage of the split and flexural tensile strength to the compressive strength. Also, test results showed a progressive increase in the areas under the stress-strain curves of the FAHSC strains after the CBFS addition. Therefore, the brittleness and toughness of the FAHSC were enhanced and the pattern of failure moved from brittle failure to ductile collapse using CBFS. It can be considered that the CBFS is a suitable strengthening material to produce ductile FAHSC.

scholarly journals Mechanical Properties and Microstructural Features using Stone Dust as a Partial Replacement of Sand

2019 ◽  
Vol 8 (6) ◽  
pp. 5232-5237
Keyword(s):  
Mechanical Properties ◽  
Economic Growth ◽  
Sustainable Development ◽  
Compressive Strength ◽  
Flexural Strength ◽  
Natural Resources ◽  
Strength Test ◽  
Partial Replacement ◽  
Test Results ◽  
Stone Dust

Today’s world is always leads to development in technology as well as the economic growth though sometime these will affect the environment badly. That’s why world environmental commission coined the termed called sustainable development where development takes place without hampering the others’ needs. Concrete industry is rapidly growing industry in India which consumes lots of natural resources during the production of concrete. Here Stone dust is used as a sustainable material in place of sand partially. M25 grade of concrete has been chosen for the experiments. Different mechanical properties of concrete like compressive strength, Split tensile, flexural strength etc. and Microstructural features like SEM, EDX have been included in this study. Compressive Strength and flexural strength test results shown the increase in the strength. Sulphate Resistance Properties have been tested by curing the cubes in the MgSO4 solution and increase in weight has been observed. Similarities are found in the SEM pictures

scholarly journals Effect of fine recycled aggregates on the properties of non-cement blended materials

2020 ◽  
Vol 323 ◽  
pp. 01018
Author(s):  
Wei-Ting Lin ◽  
Lukáš Fiala ◽  
An Cheng ◽  
Michaela Petříková
Keyword(s):  
Compressive Strength ◽  
Blast Furnace Slag ◽  
Interface Structure ◽  
Strength Test ◽  
Recycled Aggregates ◽  
Test Results ◽  
Granulated Blast Furnace Slag ◽  
Fine Aggregates ◽  
Compressive Strength Test ◽  
Furnace Slag

In this study, the different proportions of co-fired fly ash and ground granulated blast-furnace slag were used to fully replace the cement as non-cement blended materials in a fixed water-cement ratio. The recycled fine aggregates were replaced with natural fine aggregates as 10%, 20%, 30%, 40% and 50%. The flowability, compressive strength, water absorption and scanning electron microscope observations were used as the engineered indices by adding different proportions of recycled fine aggregates. The test results indicated that the fluidity cannot be measured normally due to the increase in the proportion of recycled fine aggregates due to its higher absorbability. In the compressive strength test, the compressive strength decreased accordingly as the recycled fine aggregates increased due to the interface structure and the performance of recycled aggregates. The fine aggregates and other blended materials had poor cementation properties, resulting in a tendency for their compressive strength to decrease. However, the compressive strength can be controlled above 35 MPa of the green non-cement blended materials containing 20% recycled aggregates.

scholarly journals Comparison of Conventional Concrete and Replacement of River Sand by Waste Foundry Sand and Cement by Nano-Silica

2020 ◽  
pp. 201-205
Keyword(s):  
Experimental Investigation ◽  
Compressive Strength ◽  
Partial Replacement ◽  
Fine Aggregate ◽  
Nano Silica ◽  
River Sand ◽  
Conventional Concrete ◽  
Foundry Sand ◽  
Concrete Production ◽  
Waste Foundry Sand

This paper presents an experimental investigation on the properties of concrete in which like cement is partially replacing by used nano silica and is partially replacing by used waste foundry sand. Because now a day the world wide consumption of sand as cement and as fine aggregate in concrete production is very high. Nano silica and waste foundry sand are major by product of casting industry and create land pollution. The cement will be replaced with nano silica and the river sand will be replaced with waste foundry sand (0%, 5%, 10%, 15%, 20%). This experimental investigation was done and found out that with the increase in the nano silica and waste foundry sand ratio. Compression test has been done to find out the compressive strength of concrete at the age of 7, 14, 21, and 28. Test result indicates in increasing compressive strength of plain concrete by inclusion of nano silica as a partial replacement of cement and waste foundry sand as a partial replacement of fine aggregate.

scholarly journals Suitability of Scoria as Fine Aggregate and Its Effect on the Properties of Concrete

2019 ◽  
Vol 11 (17) ◽  
pp. 4647 ◽  
Author(s):  
Warati ◽  
Darwish ◽  
Feyessa ◽  
Ghebrab
Keyword(s):  
Construction Materials ◽  
Energy Utilization ◽  
Engineering Properties ◽  
Partial Replacement ◽  
Fine Aggregate ◽  
Test Results ◽  
River Sand ◽  
Conventional Concrete ◽  
Efficient Energy ◽  
Concrete Production

The increase in the demand for concrete production for the development of infrastructures in developing countries like Ethiopia leads to the depletion of virgin aggregates and high cement demand, which imposes negative environmental impacts. In sustainable development, there is a need for construction materials to focus on the economy, efficient energy utilization, and environmental protections. One of the strategies in green concrete production is the use of locally available construction materials. Scoria is widely available around the central towns of Ethiopia, especially around the rift valley regions where huge construction activities are taking place. The aim of this paper is therefore to analyze the suitability of scoria as a fine aggregate for concrete production and its effect on the properties of concrete. A differing ratio of scoria was considered as a partial replacement of fine aggregate with river sand after analyzing its engineering properties, and its effect on the mechanical properties of concrete were examined. The test results on the engineering properties of scoria revealed that the material is suitable to be used as a fine aggregate in concrete production. The replacement of scoria with river sand also enhanced the mechanical strength of the concrete. Generally, the findings of the experimental study showed that scoria could replace river sand by up to 50% for conventional concrete production.

BEHAVIOR OF M 50 GRADE SELF-COMPACTING CONCRETE DEVELOPED USING PORTLAND SLAG CEMENT AND METAKAOLIN

2019 ◽  
Vol 6 (1) ◽  
Author(s):  
Sravya Nalla ◽  
Janardhana Maganti ◽  
Dinakar Pasla
Keyword(s):  
Compressive Strength ◽  
Mineral Admixtures ◽  
Partial Replacement ◽  
Test Results ◽  
Slag Cement ◽  
Self Compacting Concrete ◽  
Destructive Testing ◽  
Compressive Strength Test ◽  
Portland Slag Cement ◽  
Strength And Durability

Self-compacting concrete (SCC) is a revolutionary development in concrete construction. The addition of mineral admixtures like metakaolin, which is a highly reactive pozzolana to the SCC mixes, gives it superior strength and durability. The present work is an effort to study the behavior of M50 grade SCC by partial replacement of Portland Slag Cement (PSC) with metakaolin. Its strength and durability aspects are comparable with a controlled concrete (without replacement of cement). In the present work, a new mix design methodology based on the efficiency of metakaolin is adopted. The optimum percentage replacement of cement with metakaolin is obtained based on compressive strength test results. The influence of metakaolin on the workability, compressive strength, splitting tensile strength and flexural strength of SCC and its behavior when subjected to elevated temperature was investigated through evaluation against controlled concrete and non-destructive testing. From the test results, it was observed that incorporation of metakaolin at an optimum dosage satisfied all the fresh properties of SCC and improved both the strength and durability performance of SCC compared to controlled concrete.

Influence of Fly Ash and Basalt Fibers on Strength and Chloride Penetration Resistance of Self-Consolidating Concrete

2016 ◽  
Vol 866 ◽  
pp. 3-8 ◽  
Author(s):  
Osama Ahmed Mohamed ◽  
Waddah Al Hawat
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Portland Cement ◽  
Strength Properties ◽  
Chloride Penetration ◽  
Partial Replacement ◽  
Basalt Fibers ◽  
Self Consolidating Concrete ◽  
Chloride Penetration Resistance ◽  
Hardened Properties

Fly ash is a sustainable partial replacement of Portland cement that offers significant advantages in terms of fresh and hardened properties of concrete. This paper presents the findings of a study that aims at assessing the durability and strength properties of sustainable self-consolidating concrete (SCC) mixes in which Portland cement was partially replaced with 10%, 20%, 30%, and 40% fly ash. The study confirms that replacing Portland cement with fly ash at all of the percentages studied improves resistance of concrete to chloride penetration. The 40% fly ash mix exhibited the highest resistance to chloride penetration compared to the control mix. Despite the relative drop in compressive strength after 7 days of curing, the 28-day compressive strength of 40% SCC mix reached 55.75 MP, which is very close to the control mix. The study also confirms that adding 1%, 1.5%, and 2% basalt fibers, respectively, to the 40% fly ash mix improves the resistance to chloride penetration compared to the mix without basalt fibers.

Properties of Unfired Building Bricks Prepared from Fly Ash and Residual Rice Husk Ash

2015 ◽  
Vol 754-755 ◽  
pp. 468-472 ◽  
Author(s):  
Chao Lung Hwang ◽  
Trong Phuoc Huynh
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Flexural Strength ◽  
Rice Husk ◽  
Rice Husk Ash ◽  
Fine Aggregate ◽  
Test Results ◽  
Design Algorithm ◽  
Potential Applications ◽  
Hardened Properties

This work investigates the possibility of using fly ash (FA) and Vietnam residual rice husk ash (RHA) in producing unfired building bricks with applying densified mixture design algorithm (DMDA) method. In this research, little amount of cement was added into the mixtures as binder substitution. Unground rice husk ash (URHA), an agricultural by-product, was used as partial fine aggregate replacement (10% and 30%) in the mixtures. The solid bricks of 220×105×60 mm in size were prepared in this study. The hardened properties of the bricks were investigated including compressive strength, flexural strength and water absorption according to corresponding Vietnamese standards. Forming pressure of 35 MPa was applied to form the solid bricks in the mold. The test results show that all brick specimens obtained good mechanical properties, which were well conformed to Vietnamese standard. Compressive strength and flexural strength of the bricks were respectively in range of 13.81–22.06 MPa and 2.25–3.47 MPa. It was definitely proved many potential applications of FA and RHA in the production of unfired building bricks.

Sign in / Sign up

Export Citation Format

Share Document