scholarly journals Characterization and modification of natural clay deposits to develop clay-based adsorbent to remove phosphorus from contaminated water

2021 ◽  
Author(s):  
◽  
Farzana Nargis
Keyword(s):  
Adsorption Capacity ◽  
Low Cost ◽  
Continuous Process ◽  
Fixed Bed ◽  
Contaminated Water ◽  
Maximum Adsorption Capacity ◽  
Natural Clay ◽  
Phosphorus Adsorption ◽  
Modified Clay ◽  
Clay Deposits

Modification of natural clays may be a useful approach to produce an effective and low-cost adsorbent to control phosphorous, which is a key factor in controlling the eutrophication of surface waters. In this study, natural clay samples were collected, characterized, modified with ZrCl4, and then their adsorption capacity for removing phosphorus from contaminated water was studied. XRD analysis showed that the natural clay consists of kaolinite, illite, and nontronite as dominant clay mineral phases. The maximum adsorption capacity of the modified clay increased from 0.493 to 11.83 mg P/g compared to the unmodified clay. The adsorption process was fast for both natural and modified samples, achieving more than 80% and 90% phosphorus removal with natural and modified samples, respectively in less than 4 hours. The adsorption data for both clays best fit the Langmuir isotherm, and the rate of phosphorus adsorption was found to follow a pseudo-secondorder kinetic model. The adsorption capacity of both adsorbents decreased with increasing pH, and for the modified clay the change was more significant. Full factorial design and response surface methodology were applied to evaluate and optimize the effects of initial P concentration, contact time, pH, and dose. From the model, the maximum P removal efficiency predicted for the synthetic solution was 91.5% and 99.9% by natural and modified clay, respectively. R2(≈0.98) indicates that the observed results fitted well with the model prediction. Similar to the batch studies, the fixed bed column study showed the developed adsorbents are efficient in removing phosphorus from water in a continuous process as well.

scholarly journals H-Clinoptilolite as an Efficient and Low-Cost Adsorbent for Batch and Continuous Gallium Removal from Aqueous Solutions

2021 ◽  
Author(s):  
P. Sáez ◽  
A. Rodríguez ◽  
J. M. Gómez ◽  
C. Paramio ◽  
C. Fraile ◽  
...  
Keyword(s):  
Particle Size ◽  
Adsorption Capacity ◽  
Low Cost ◽  
Fixed Bed ◽  
Particle Size Effect ◽  
Breakthrough Curves ◽  
Maximum Adsorption Capacity ◽  
Fixed Bed Column ◽  
Gallium Concentration ◽  
Best Fit

AbstractIn this paper, the gallium (III) ions’ adsorption onto protonated clinoptilolite (H-CLP) was investigated both in batch and fixed-bed column experiments. Regarding batch experiments, the influence of some parameters such as adsorbent dosage, size particle, and temperature was studied, determining that a dosage of 10 g/L for an initial pollutant concentration of 40 mg/L leads to a removal percentage over 85% regardless of particle size and temperature. On the other hand, adsorption of gallium onto H-CPL is an endothermic and spontaneous process in the studied temperature range, concluding that the maximum adsorption capacity was 16 mg/g for 60 °C. Concerning to the effect of the presence of other cations in solution, such as Na+, K+, or Ca2+, gallium adsorption capacity only drops by 20%, although the initial concentration of other cations in the solution is 50 times higher than gallium concentration. This means that clinoptilolite has a high affinity for gallium which can be very favorable for further selectivity tests. A crucial factor for this high selectivity could be the protonation of clinoptilolite which allows working without modifying the pH of the aqueous solution with acid. In the fixed-bed experiments, breakthrough curves were obtained, and the effect of operation variables was determined. A breakpoint value of 254 min for 64 g of adsorbent and flow rate of 9.0 mL/min (7.0 BV/h) were obtained, when treating a pollutant volume of 33 BV. Additionally, the breakthrough curves were fitted to different models to study the particle size effect, being the best fit corresponding to the Adams–Bohart model. This fact confirmed the influence of particle size on adsorption kinetics. Graphical Abstract

Parameters Affecting Dye Adsorption - Using Graphene Coated Sand (GSC)

2018 ◽  
Vol 4 (02) ◽  
Author(s):  
Seroor Atalah Khaleefa Alia ◽  
Dr. Mohammed Ibrahimb ◽  
Hussein Ali Hussein
Keyword(s):  
Heavy Metals ◽  
Contact Time ◽  
Organic Dyes ◽  
Low Cost ◽  
Dye Adsorption ◽  
Contaminated Water ◽  
Maximum Adsorption Capacity ◽  
Engineering Designs ◽  
Heavy Metals Ions ◽  
Coated Sand

Adsorption is most commonly applied process for the removal of pollutants such as dyes and heavy metals ions from wastewater. The present work talks about preparing graphenic material attached sand grains called graphene sand composite (GSC) by using ordinary sugar as a carbon source. Physical morphology and chemical composition of GSC was examined by using (FTIR, SEM, EDAX and XRD). Efficiency of GSC in the adsorption of organic dyes from water was investigated using reactive green dye with different parameters such as (ph, temperature, contact time and dose). Adsorption isotherm was also studied and the results showed that the maximum adsorption capacity of dye is 28.98 mg/g. This fast, low-cost process can be used to manufacture commercial filters to treat contaminated water using appropriate engineering designs.

scholarly journals Sequential Oxidation on Wood and Its Application in Pb2+ Removal from Contaminated Water

2021 ◽  
Vol 2 (2) ◽  
pp. 245-256
Author(s):  
Priyanka R. Sharma ◽  
Sunil K. Sharma ◽  
Marc Nolan ◽  
Wenqi Li ◽  
Lakshta Kundal ◽  
...  
Keyword(s):  
Adsorption Capacity ◽  
Average Length ◽  
Sodium Chlorite ◽  
Contaminated Water ◽  
Maximum Adsorption Capacity ◽  
Fiber Morphology ◽  
Carboxylate Groups ◽  
Carboxylate Content ◽  
Wide Range ◽  
Length Width

Raw wood was subjected to sequential oxidation to produce 2,3,6-tricarboxycellulose (TCC) nanofibers with a high surficial charge of 1.14 mmol/g in the form of carboxylate groups. Three oxidation steps, including nitro-oxidation, periodate, and sodium chlorite oxidation, were successfully applied to generate TCC nanofibers from raw wood. The morphology of extracted TCC nanofibers measured using TEM and AFM indicated the average length, width, and thickness were in the range of 750 ± 110, 4.5 ± 1.8, and 1.23 nm, respectively. Due to high negative surficial charges on TCC, it was studied for its absorption capabilities against Pb2+ ions. The remediation results indicated that a low concentration of TCC nanofibers (0.02 wt%) was able to remove a wide range of Pb2+ ion impurities from 5–250 ppm with an efficiency between 709–99%, whereby the maximum adsorption capacity (Qm) was 1569 mg/g with R2 0.69531 calculated from Langmuir fitting. It was observed that the high adsorption capacity of TCC nanofibers was due to the collective effect of adsorption and precipitation confirmed by the FTIR and SEM/EDS analysis. The high carboxylate content and fiber morphology of TCC has enabled it as an excellent substrate to remove Pb2+ ions impurities.

scholarly journals Removal of Chromium(III) and Cadmium(II) Heavy Metal Ions from Aqueous Solutions Using Treated Date Seeds: An Eco-Friendly Method

Molecules ◽  
2021 ◽  
Vol 26 (12) ◽  
pp. 3718
Author(s):  
Mohammad Azam ◽  
Saikh Mohammad Wabaidur ◽  
Mohammad Rizwan Khan ◽  
Saud I. Al-Resayes ◽  
Mohammad Shahidul Islam
Keyword(s):  
Metal Ions ◽  
Adsorption Capacity ◽  
Low Cost ◽  
Maximum Adsorption Capacity ◽  
Solution Ph ◽  
Surface Analysis Techniques ◽  
Adsorption Processes ◽  
Ft Ir ◽  
Metal Elution ◽  
Date Pits

The aim of the research was to prepare low-cost adsorbents, including raw date pits and chemically treated date pits, and to apply these materials to investigate the adsorption behavior of Cr(III) and Cd(II) ions from wastewater. The prepared materials were characterized using SEM, FT-IR and BET surface analysis techniques for investigating the surface morphology, particle size, pore size and surface functionalities of the materials. A series of adsorption processes was conducted in a batch system and optimized by investigating various parameters such as solution pH, contact time, initial metal concentrations and adsorbent dosage. The optimum pH for achieving maximum adsorption capacity was found to be approximately 7.8. The determination of metal ions was conducted using atomic adsorption spectrometry. The experimental results were fitted using isotherm Langmuir and Freundlich equations, and maximum monolayer adsorption capacities for Cr(III) and Cd(II) at 323 K were 1428.5 and 1302.0 mg/g (treated majdool date pits adsorbent) and 1228.5 and 1182.0 mg/g (treated sagai date pits adsorbent), respectively. It was found that the adsorption capacity of H2O2-treated date pits was higher than that of untreated DP. Recovery studies showed maximal metal elution with 0.1 M HCl for all the adsorbents. An 83.3–88.2% and 81.8–86.8% drop in Cr(III) and Cd(II) adsorption, respectively, were found after the five regeneration cycles. The results showed that the Langmuir model gave slightly better results than the Freundlich model for the untreated and treated date pits. Hence, the results demonstrated that the prepared materials could be a low-cost and eco-friendly choice for the remediation of Cr(III) and Cd(II) contaminants from an aqueous solution.

scholarly journals Potential of Araucaria angustifolia bark as adsorbent to remove Gentian Violet dye from aqueous effluents

2018 ◽  
Vol 78 (8) ◽  
pp. 1693-1703 ◽  
Author(s):  
Jordana Georgin ◽  
Fernanda Caroline Drumm ◽  
Patrícia Grassi ◽  
Dison Franco ◽  
Daniel Allasia ◽  
...  
Keyword(s):  
Gentian Violet ◽  
Low Cost ◽  
Fixed Bed ◽  
Amorphous Structure ◽  
Maximum Adsorption Capacity ◽  
Araucaria Angustifolia ◽  
Wood Processing ◽  
Fixed Bed Adsorption ◽  
Aqueous Effluents ◽  
Equilibrium Data

Abstract Araucaria angustifolia bark (AA-bark), a waste generated in wood processing, was evaluated as a potential adsorbent to remove Gentian Violet (GV) dye from aqueous solutions. The AA-bark presented an amorphous structure with irregular surface and was composed mainly of lignin and holocellulose. These characteristics indicated that the adsorbent contains available sites to accommodate the dye molecules. The GV adsorption on AA-bark was favored at pH 8.0 with adsorbent dosage of 0.80 g L−1. Pseudo-nth order model was adequate to represent the adsorption kinetics of GV on AA-bark. A fast adsorption rate was verified, with the equilibrium being attained within 30 min. Equilibrium data were well represented by the Langmuir model. The maximum adsorption capacity was 305.3 mg g−1. Adsorption was spontaneous, favorable and endothermic. AA-bark was able to treat a simulated dye house effluent, reaching color removal values of 80%. An excellent performance was found in fixed bed experiments, where the length of the mass transfer zone was only 5.38 cm and the breakthrough time was 138.5 h. AA-bark can be regenerated two times using HNO3 0.5 mol L−1. AA-bark can be used as a low-cost material to treat colored effluents in batch and fixed bed adsorption systems.

scholarly journals Adsorption Study of Cu2+ Ions from Aqueous Solutions by Bael Flowers (Aegle marmelos)

2020 ◽  
Vol 11 (4) ◽  
pp. 11891-11904
Keyword(s):  
Aqueous Solutions ◽  
Adsorption Capacity ◽  
Metal Ion ◽  
Low Cost ◽  
Sem Analysis ◽  
Ion Concentration ◽  
Maximum Adsorption Capacity ◽  
Aegle Marmelos ◽  
Batch Mode ◽  
Initial Ph

In the present study, batch mode adsorption was carried out to investigate the adsorption capacity of dried bael flowers (Aegle marmelos) for the adsorptive removal of Cu(II) ions from aqueous solutions by varying agitation time, initial metal concentration, the dose of adsorbent, temperature, and initial pH of the Cu(II) ion solution. The percentage removal of 98.7% was observed at 50 ppm initial metal ion concentration, 0.5 g/100.00 cm3 adsorbent dosage, within the contact time of 120 minutes at 30 ºC in the pH range of 4 – 7. The sorption processes of Cu(II) ions was best described by pseudo-second-order kinetics. Langmuir isotherm had a good fit with the experimental data with 0.97 of correlation coefficient (R2), and the maximum adsorption capacity obtained was 23.14 mg g-1 at 30 ºC. The results obtained from sorption thermodynamic studies suggested that the adsorption process is exothermic and spontaneous. SEM analysis showed tubular voids on the adsorbent. FTIR studies indicated the presence of functional groups like hydroxyl, –C-O, –C=O, and amide groups in the adsorbent, which can probably involve in metal ion adsorption. Therefore, dried bael flowers can be considered an effective low-cost adsorbent for treating Cu(II) ions.

Removal of VOCs Using Sludge-Based Adsorbents

2012 ◽  
Vol 599 ◽  
pp. 305-308 ◽  
Author(s):  
Ping Fang ◽  
Chao Ping Cen ◽  
Hong Tao Zhang ◽  
Zi Jun Tang ◽  
Ding Sheng Chen ◽  
...  
Keyword(s):  
Adsorption Capacity ◽  
Physical Adsorption ◽  
Low Cost ◽  
Fixed Bed ◽  
Cost Effective ◽  
Langmuir Adsorption Isotherm ◽  
Fixed Bed Reactor ◽  
Dynamic Adsorption ◽  
Langmuir Adsorption ◽  
Isotherm Equations

Efficient and cost-effective sludge-based adsorbents were developed and the adsorption of VOCs on the sludge-based adsorbents was studied in a fixed bed reactor. The results indicate that the adsorption of VOCs on sludge-based adsorbents is typical physical adsorption, the dynamic adsorption capacity of VOCs on adsorbents sharply increases as the VOCs concentration is increased at first, then increasing gradually, at last retains stable with the change of VOCs concentration. The dynamic adsorption capacity of sludge-based adsorbents for VOCs is O-Xylene > Butylcetate > Toluene > Ethylacetate > Benzene > Propanone > n-Hexane, the maximum dynamic adsorption capacity is 0.247, 0.225, 0.192, 0.186, 0.180, 0.176, 0.133g/g, respectively. Meanwhile the adsorption of VOCs on sludge-based adsorbents corresponds to the Langmuir adsorption isotherm equations. The sludge-based adsorbent is a low-cost alternative to activated carbon for VOCs treatment, and this technology is a promising method for the VOCs removal.

Insights into the mechanism of methylene blue removed by novel and classic biochars

2019 ◽  
Vol 79 (8) ◽  
pp. 1561-1570
Author(s):  
Wei Chen ◽  
Fengting Chen ◽  
Bin Ji ◽  
Lin Zhu ◽  
Hongjiao Song
Keyword(s):  
Methylene Blue ◽  
Adsorption Capacity ◽  
Ph Value ◽  
Low Cost ◽  
Underlying Mechanism ◽  
Maximum Adsorption Capacity ◽  
Experimental Conditions ◽  
Average Pore ◽  
Adsorption Effect ◽  
Magnolia Grandiflora

Abstract The adsorption behavior and the underlying mechanism of methylene blue (MB) sorption on biochars prepared from different feedstocks at 500 °C were evaluated. The biochar feedstocks included Magnolia grandiflora Linn. leaves biochar (MBC), pomelo (Citrus grandis) peel biochar (PBC) and badam shell biochar (BBC). The results of characterizing and analyzing the samples showed that different biochars had different effects on the adsorption of MB. It could be found that MBC had the best adsorption effect on MB due to its largest average pore diameter of 5.55 nm determined by Brunauer-Emmett-Teller analysis. Under the optimal conditions, the maximum adsorption capacities of BBC, PBC and MBC were 29.7, 85.15 and 99.3 mg/g, respectively. The results showed that the amount of adsorption was affected by the pH value. The maximum adsorption capacity of MBC was 46.99 mg/g when it was at pH of 3, whereas for the same experimental conditions the maximum adsorption capacity of BBC and PBC was 25.29 mg/g at pH of 11 and 36.08 mg/g at pH of 7, respectively. Therefore, MBC was found to be a most efficient low-cost adsorbentl for dye wastewater treatment compared with BBC and PBC, and it had the best removal effect under acidic conditions.

scholarly journals Compressive Alginate Sponge Derived from Seaweed Biomass Resources for Methylene Blue Removal from Wastewater

Polymers ◽  
2019 ◽  
Vol 11 (6) ◽  
pp. 961 ◽  
Author(s):  
Xiaojun Shen ◽  
Panli Huang ◽  
Fengfeng Li ◽  
Xiluan Wang ◽  
Tongqi Yuan ◽  
...  
Keyword(s):  
Methylene Blue ◽  
Water Treatment ◽  
Low Cost ◽  
Fixed Bed ◽  
Polymer Materials ◽  
Batch Adsorption ◽  
Maximum Adsorption Capacity ◽  
Seaweed Biomass ◽  
Biomass Resources ◽  
The Impact

Low cost fabrication of water treatment polymer materials directly from biomass resources is urgently needed in recent days. Herein, a compressive alginate sponge (AS) is prepared from seaweed biomass resources through a green two-step lyophilization method. This material is much different from conventional oven-, air-, vacuum-dried alginate-based adsorbents, which show limitations of shrinkage, rigidness, tight nonporous structure and restricted ions diffusion, hindering its practical applications, and was used to efficiently remove methylene blue (MB), a main colorful contaminant in dye manufacturing, from wastewater. The batch adsorption studies are carried out to determine the impact of pH, contact time and concentration of dye on the adsorption process. The maximum adsorption capacity can be obtained at 1279 mg g−1, and the shape-moldable AS can be facilely utilized as a fixed-bed absorption column, providing an efficient approach for continuous removal of MB within a short time. It is also important that such a compressive AS can be regenerated by a simple squeezing method while retaining about 70% capacity for more than ten cycles, which is convenient to be reused in practical water treatment. Compressive AS demonstrates its merits of high capability, large efficiency and easy to recycle as well as low cost resources, indicating widespread potentials for application in dye contaminant control regarding environmental protection.

Potential of Agricultural Waste Material (Ananas cosmos) as Biosorbent for Heavy Metal Removal in Polluted Water

2020 ◽  
Vol 1010 ◽  
pp. 489-494
Author(s):  
Abdul Hafidz Yusoff ◽  
Rosmawani Mohammad ◽  
Mardawani Mohamad ◽  
Ahmad Ziad Sulaiman ◽  
Nurul Akmar Che Zaudin ◽  
...  
Keyword(s):  
Heavy Metals ◽  
Heavy Metal ◽  
Adsorption Capacity ◽  
Metal Removal ◽  
Low Cost ◽  
Agricultural Waste ◽  
Heavy Metal Removal ◽  
Polluted Water ◽  
Maximum Adsorption Capacity ◽  
Pineapple Peel

Conventional methods to remove heavy metals from polluted water are expensive and not environmentally friendly. Therefore, this study was carried out to investigate the potential of agricultural waste such as pineapple peel (Ananas Cosmos) as low-cost absorbent to remove heavy metals from synthetic polluted water. The results showed that Cd, Cr and Pb were effectively removed by the biosorbent at 12g of pineapple peels in 100 mL solution. The optimum contact time for maximum adsorption was found to be 90 minutes, while the optimum pH for the heavy metal’s adsorption was 9. It was demonstrated that with the increase of adsorbent dosage, the percent of heavy metals removal was also increased due to the increasing adsorption capacity of the adsorbent. In addition, Langmuir model show maximum adsorption capacity of Cd is 1.91 mg/g. As conclusions, our findings show that pineapple peel has potential to remove heavy metal from polluted water.

Sign in / Sign up

Export Citation Format

Share Document