scholarly journals Porosity distribution in metal injection molded parts

2021 ◽  
Vol 46 (1) ◽  
pp. 7-10
Author(s):  
Samir Butković ◽  
Emir Šarić ◽  
Muhamed Mehmedović
Keyword(s):  
Injection Molding ◽  
Cross Section ◽  
Density Variation ◽  
Residual Porosity ◽  
Metal Injection Molding ◽  
Green Density ◽  
Shaped Part ◽  
Molded Parts ◽  
Injection Molded ◽  
Complex Parts

Metal injection molding technology is commonly used in production of small and very complex parts. Residual porosity is unavoidable characteristic of P/M parts, affecting their final properties. During injection molding phase powder-binder separation can occur, causing green density variation through cross section of the part. This behaviour is particularly pronounced as complexity of the parts increases. As a consequence, zones with different density and residual porosity can be seen after sintering. In this regard, porosity and hardness distribution of the sintered ring-shaped part is analysed and presented in the paper.

Direct Sinter Bonding of Metal Injection-Molded Parts to Solid Substrate Through Use of Deformable Surface Microfeatures

2013 ◽  
Vol 1 (1) ◽  
Author(s):  
Thomas Martens ◽  
M. Laine Mears
Keyword(s):  
Injection Molding ◽  
Solid Substrate ◽  
Metal Injection Molding ◽  
Full Density ◽  
Metal Powders ◽  
Molded Parts ◽  
Primary Obstacle ◽  
Injection Molded ◽  
Sinter Bonding ◽  
Micro Features

In the metal injection molding (MIM) process, fine metal powders are mixed with a binder and injected into molds, similar to plastic injection molding. After molding, the binder is removed from the part, and the compact is sintered to almost full density. Though able to create high-density parts of excellent dimensional control and surface finish, the MIM process is restricted in the size of part that can be produced, due to gravitational deformation during high-temperature sintering and maximum thickness requirements to remove the binding agents in the green state. Larger parts could be made by bonding the green parts to a substrate during sintering; however, a primary obstacle to this approach lies in the sinter shrinkage of the MIM part, which can be up to 20%, meaning that the MIM part shrinks during sintering, while the conventional substrate maintains its dimensions. This behavior would typically inhibit bonding and/or cause cracking and deformation of the MIM part. In this work, we present a structure of micro features molded onto the surface of the MIM part, which bonds, deforms, and allows for shrinkage while bonding to the substrate. The micro features tolerate plastic deformation to permit the shrinkage without causing cracks after the initial bonds are established. In a first series of tests, bond strengths of up to 80% of that of resistance welds have been achieved. This paper describes how the authors developed their proposed method of sinter bonding and how they accomplished effective sinter bonds between MIM parts and solid substrates.

scholarly journals Are We Able to Print Components as Strong as Injection Molded?—Comparing the Properties of 3D Printed and Injection Molded Components Made from ABS Thermoplastic

2021 ◽  
Vol 11 (15) ◽  
pp. 6946
Author(s):  
Bartłomiej Podsiadły ◽  
Andrzej Skalski ◽  
Wiktor Rozpiórski ◽  
Marcin Słoma
Keyword(s):  
Tensile Strength ◽  
Injection Molding ◽  
Mechanical Strength ◽  
Cross Section ◽  
Fused Deposition Modeling ◽  
High Strength ◽  
Large Cross Section ◽  
Fused Deposition ◽  
Injection Molded ◽  
The Cross

In this paper, we are focusing on comparing results obtained for polymer elements manufactured with injection molding and additive manufacturing techniques. The analysis was performed for fused deposition modeling (FDM) and single screw injection molding with regards to the standards used in thermoplastics processing technology. We argue that the cross-section structure of the sample obtained via FDM is the key factor in the fabrication of high-strength components and that the dimensions of the samples have a strong influence on the mechanical properties. Large cross-section samples, 4 × 10 mm2, with three perimeter layers and 50% infill, have lower mechanical strength than injection molded reference samples—less than 60% of the strength. However, if we reduce the cross-section dimensions down to 2 × 4 mm2, the samples will be more durable, reaching up to 110% of the tensile strength observed for the injection molded samples. In the case of large cross-section samples, strength increases with the number of contour layers, leading to an increase of up to 97% of the tensile strength value for 11 perimeter layer samples. The mechanical strength of the printed components can also be improved by using lower values of the thickness of the deposited layers.

scholarly journals Effects of Injection Molding Screw Tips on Polymer Mixing

2018 ◽  
Vol 62 (3) ◽  
pp. 241-246 ◽  
Author(s):  
Dániel Török ◽  
József Gábor Kovács
Keyword(s):  
Injection Molding ◽  
Processing Parameters ◽  
Raw Material ◽  
Molding Machine ◽  
Surface Color ◽  
Melt Temperature ◽  
Injection Molding Machine ◽  
Aesthetic Appearance ◽  
Molded Parts ◽  
Injection Molded

In all fields of industry it is important to produce parts with good quality. Injection molded parts usually have to meet strict requirements technically and aesthetically. The aim of the measurements presented in our paper is to investigate the aesthetic appearance, such as surface color homogeneity, of injection molded parts. It depends on several factors, the raw material, the colorants, the injection molding machine and the processing parameters. In this project we investigated the effects of the injection molding machine on surface color homogeneity. We focused on injection molding screw tips and investigated five screw tips with different geometries. We produced flat specimens colored with a masterbatch and investigated color homogeneity. To evaluate the color homogeneity of the specimens, we used digital image analysis software developed by us. After that we measured the plastication rate and the melt temperature of the polymer melt because mixing depends on these factors. Our results showed that the screw tips (dynamic mixers) can improve surface color homogeneity but they cause an increase in melt temperature and a decrease in the plastication rate.

scholarly journals The Effect of the Holding Pressure Profile on the Metal Injection Molded Component Dimensions after Sintering

2020 ◽  
Vol 14 (4) ◽  
pp. 423-427
Author(s):  
Emir Šarić ◽  
Samir Butković ◽  
Muhamed Mehmedović
Keyword(s):  
Injection Molding ◽  
Coordinate Measuring Machine ◽  
Volumetric Flow Rate ◽  
Pressure Profile ◽  
Metal Injection Molding ◽  
Injection Velocity ◽  
Outer Diameter ◽  
N2 Atmosphere ◽  
Measuring Machine ◽  
Injection Molded

The volumetric flow rate (injection velocity) and the holding pressure are metal injection molding (MIM) parameters that have a strong influence on the green parts density and density homogeneity, but their effect on sintered dimensions after sintering is still to a large extent unexplored. To reveal the relationship between the injection molding parameters and sintered dimensions, ring-shaped components were injection molded by using different values of injection velocities in combination with a rump-down and rumpup holding pressure profile. Afterwards, the green components were catalytically debound and sintered in the nitrogen (N2) atmosphere. Finally, the component dimensions: the height, inner and outer diameter were measured by using a coordinate measuring machine. The ready-to-mold granules Catamold 310N made of heat resistant stainless steel X40CrNiSi 25-20 (according to the EN standard) powder and polyacetal based binder were used. The results showed that the interaction between the injection velocity and the holding pressure profile can be used to systematically adjust shrinkage after sintering. This approach is based on the dependence of the binder crystallization temperature on pressure, when the powder/binder proportion changes with the injection velocity.

Study of the Structural Characteristics of Mold for Precise Injection Molding

2011 ◽  
Vol 291-294 ◽  
pp. 610-613
Author(s):  
Hong Lin Li ◽  
Zhi Xin Jia
Keyword(s):  
Injection Molding ◽  
Process Parameters ◽  
Structural Characteristics ◽  
Injection Mold ◽  
Industrial Products ◽  
Balance System ◽  
Molded Parts ◽  
Manufacturing Accuracy ◽  
Injection Molded

With the improvement of accuracy requirements for industrial products, the precise injection molding is replacing the traditional injection molding quickly and widely. Many factors influence the quality of injection-molded parts greatly, such as the property of the plastics, mold structure and the manufacturing accuracy, injecting machine and the injecting process parameters. In this paper, the work is emphasized for the influence of mold structure on the quality of injection-molded parts. Eight portions of injection mold are analyzed, including the cavities and cores, the guide components, the runner system, the ejection system, the side-core pulling mechanism, the temperature balance system, the venting system and the supporting parts. The structural characteristics of the above eight portions are presented.

Binder Design for Fabricating Internal Crack-Free Injection-Molded Si3N4-Based Ceramics

1991 ◽  
Vol 249 ◽  
Author(s):  
Sophia R. Su
Keyword(s):  
Mass Transfer ◽  
Injection Molding ◽  
Cross Section ◽  
Decomposition Temperature ◽  
Internal Crack ◽  
Large Cross Section ◽  
Binder Removal ◽  
Ceramic Injection Molding ◽  
Injection Molded ◽  
The Right

ABSTRACTBinder design is an important issue in ceramic injection molding technology. The binder decomposition mechanism, which involves thermodynamics, kinetics, as well as heat and mass transfer, controls the binder removal process. This process, in turn, is governed by the thermal and physical characteristics of the organic waxes used, and is the most critical step in injection molding ceramics. In this paper, we present the binder design philosophy and the method of binder selection. A systematic binder removal study focusing on heating rate, setter powder, and sublimable materials was carried out with the selected compositions. As a result of this study, we concluded that the fluid wicking controls the binder removal at the molten temperature of the binder, and the diffusion and permeation-controlled mechanism dominate at the decomposition temperature range of the binder. With the right binder selection, it is feasible to produce internal and external crack-free large cross-section injection-molded ceramic parts.

Study on Improving the Life of Stereolithography Injection Mold

2012 ◽  
Vol 468-471 ◽  
pp. 1013-1016 ◽  
Author(s):  
Hua Qing Lai
Keyword(s):  
Injection Molding ◽  
Injection Molding Process ◽  
Injection Mold ◽  
Molding Process ◽  
Molded Parts ◽  
Injection Molded ◽  
Plastic Parts ◽  
Assembly Operations ◽  
Conventional Injection Molding ◽  
Shape And Size

Molding is one of the most versatile and important processes for manufacturing complex plastic parts. It is a method of fabricating plastic parts by utilizing a mold or cavity that has a shape and size similar to the part being produced. Molten polymer is injected into the cavity, resulting in the desired part upon solidification. The injection-molded parts typically have excellent dimensional tolerance and require almost no finishing and assembly operations. But new variations and emerging innovations of conventional injection molding have been continuously developed to offer special features and benefits that cannot be accomplished by the conventional injection molding process. This study aims to improving the life of stereolithography injection mold.

scholarly journals Influence of process parameters and runner geometry on shear heating effect

Mechanik ◽  
2018 ◽  
Vol 91 (1) ◽  
pp. 36-38 ◽  
Author(s):  
Przemysław Poszwa ◽  
Paweł Brzęk ◽  
Marek Szostak
Keyword(s):  
Cross Section ◽  
Thermal Sensitivity ◽  
Processing Parameters ◽  
High Viscosity ◽  
Heating Effect ◽  
Influence Of Process Parameters ◽  
Molded Parts ◽  
Significant Temperature ◽  
Shear Heating ◽  
Injection Molded

Shear heating effect that occurs in melted polymers can cause serious quality problems with production of injection molded parts. The source of this effect is high viscosity of polymers and low thermal conductivity what leads to significant temperature gradients at the cross section of runners. In this work the influence of processing parameters on this phenomenon for difference runner diameters and lengths was presented for two polymers that have different thermal sensitivity.

scholarly journals Reducing the Burn Marks on Injection-Molded Parts by External Gas-Assisted Injection Molding

Polymers ◽  
2021 ◽  
Vol 13 (23) ◽  
pp. 4087
Author(s):  
Jiquan Li ◽  
Wenyong Liu ◽  
Xinxin Xia ◽  
Hangchao Zhou ◽  
Liting Jing ◽  
...  
Keyword(s):  
Image Processing ◽  
Injection Molding ◽  
Delay Time ◽  
Quantitative Method ◽  
Surface Defect ◽  
Processing Method ◽  
Traditional Methods ◽  
Molded Parts ◽  
Injection Molded ◽  
Conventional Injection Molding

A burn mark is a sort of serious surface defect on injection-molded parts. In some cases, it can be difficult to reduce the burn marks by traditional methods. In this study, external gas-assisted injection molding (EGAIM) was introduced to reduce the burn marks, as EGAIM has been reported to reduce the holding pressure. The parts with different severities of burn marks were produced by EGAIM and conventional injection molding (CIM) with the same molding parameters but different gas parameters. The burn marks were quantified by an image processing method and the quantitative method was introduced to discuss the influence of the gas parameters on burn marks. The results show that the burn marks can be eliminated by EGAIM without changing the structure of the part or the mold, and the severity of the burn marks changed from 4.98% with CIM to 0% with EGAIM. Additionally, the gas delay time is the most important gas parameter affecting the burn marks.

scholarly journals Peculiarities of Injection Molding Conducting Composites

2018 ◽  
Vol 248 ◽  
pp. 01006
Author(s):  
Yovial Mahyoedin ◽  
Jaafar Sahari ◽  
Andanastuti Mukhtar ◽  
Norhamidi Mohammad ◽  
Iqbal
Keyword(s):  
Composite Material ◽  
Carbon Black ◽  
Injection Molding ◽  
Test Procedure ◽  
Molded Parts ◽  
Twin Screw ◽  
Probe Test ◽  
Injection Molded ◽  
Conducting Composites

The investigations in this study focused on the characteristic of feedstock in an effort to understand the mechanism of injection molded in composite material. A composite, which has 75% wt. filler, consist of graphite (G), carbon black (CB) and polypropylene copolymer (PP). Twin-screw co-rotating extruder used for mixing materials. The conductivity of the molded parts measured using a four-point probe test procedure. The results showed that the injection molding conducting composites, which aggregated into larger clusters, tended to disperse unevenly into the PP, resulting in fewer particle-particle contacts and, consequently, a lower-conductivity composite in some part of the molded.

Sign in / Sign up

Export Citation Format

Share Document