scholarly journals Influence of elastic 3D printed polymers on the mechanical properties and tribology of textile fabrics

2021 ◽  
Vol 2 (2) ◽  
pp. 115-122
Author(s):  
Andrea Ehrmann ◽  
Pia Steinmetz
Keyword(s):  
Mechanical Properties ◽  
3D Printing ◽  
Tribological Properties ◽  
Surface Resistance ◽  
Thermoplastic Polyurethane ◽  
Textile Fabrics ◽  
3D Printed ◽  
Printed Patterns

Combining textile fabrics with 3D printing has been investigated intensively during the last years. Mostly, research concentrated on the adhesion between both partners of the composite or on the new freedom of design, enabled by combining these techniques. Here, we present examinations of the influence of elastic 3D printed patterns on the elongation and wearing out of elastic textile fabrics as well as on the tribological properties of the textile surface, comparing pure and imprinted textile fabrics. Therefore, thermoplastic polyurethane (TPU) was 3D printed in different patterns on diverse textile fabrics. Our study shows that for a sufficient adhesion, reached by small enough nozzle-fabric distance, elastic 3D printed patterns can indeed improve the surface resistance against wear.

scholarly journals Influence of washing on the adhesion between 3D-printed TPU and woven fabrics

2021 ◽  
Vol 2 (1) ◽  
pp. 34-39
Author(s):  
Jannik Störmer ◽  
Daniel Görmer ◽  
Andrea Ehrmann
Keyword(s):  
3D Printing ◽  
Strong Correlation ◽  
Thermoplastic Polyurethane ◽  
Cotton Fabrics ◽  
Woven Fabrics ◽  
Textile Fabrics ◽  
Fabric Structure ◽  
High Adhesion ◽  
3D Printed ◽  
Textile Fabric

3D printing on textile fabrics can be used to create composites with position-dependent mechanical, water-resistant, magnetic or other properties. An important prerequisite to use such composites technologically or for design purposes is a sufficient adhesion between both materials. While previous studies revealed that soft, elastic printing polymers were advantageous to prepare connections with a high adhesion, not much research has been performed yet on the dependence of the adhesion on textile fabric structure, heat post-treatment, and the influence of washing, which is necessary for most applications of such composites. Here we investigate composites from thermoplastic polyurethane (TPU) 3D-printed on two different woven cotton fabrics. Besides the expected strong correlation of the adhesion with the distance between nozzle and printing bed, we find a higher adhesion on the thinner fabric and an increase in the adhesion after one washing cycle.

scholarly journals The influence of thermal after-treatment on the adhesion of 3D prints on textile fabrics

2020 ◽  
Vol 1 (2) ◽  
pp. 104-110
Author(s):  
Andrea Ehrmann ◽  
Daniel Görmer ◽  
Jannik Störmer
Keyword(s):  
Mechanical Properties ◽  
3D Printing ◽  
Emerging Technologies ◽  
Knitted Fabrics ◽  
New Approach ◽  
Textile Fabrics ◽  
3D Printed ◽  
Printed Materials

3D printing belongs to the emerging technologies of our time. While it enables producing new structures and makes individualized products affordable, 3D printed objects still suffer from low production speed and often insufficient mechanical properties. Both these problems can be tackled by combining 3D printing with substrates prepared by conventional technologies, e.g. textile fabrics. In this case, the adhesion between both partners is most challenging and defines for which possible applications such composites are suitable. Here, we report on a new approach to increase the adhesion between 3D printed materials and warp knitted fabrics, showing that in some cases a thermal after-treatment, in the simplest case performed by ironing, is able to significantly increase the adhesion between both materials.

Physical property of 3D-printed sinusoidal pattern using shape memory TPU filament

2020 ◽  
Vol 90 (21-22) ◽  
pp. 2399-2410 ◽  
Author(s):  
Shahbaj Kabir ◽  
Hyelim Kim ◽  
Sunhee Lee
Keyword(s):  
Mechanical Properties ◽  
Tensile Test ◽  
Shape Memory ◽  
Fused Deposition Modeling ◽  
Loss Modulus ◽  
Thermoplastic Polyurethane ◽  
Heating Process ◽  
Fused Deposition ◽  
3D Printed ◽  
Sinusoidal Pattern

This study has investigated the physical properties of 3D-printable shape memory thermoplastic polyurethane (SMTPU) filament and its 3D-printed sinusoidal pattern obtained by fused deposition modeling (FDM) technology. To investigate 3D filaments, thermoplastic polyurethane (TPU) and SMTPU filament were examined by conducting infrared spectroscopy, x-ray diffraction (XRD), dynamic mechanical thermal analysis (DMTA), differential scanning calorimetry (DSC) and a tensile test. Then, to examine the 3D-printed sinusoidal samples, a sinusoidal pattern was developed and 3D-printed. Those samples went through a three-step heating process: (a) untreated state; (b) 5 min heating at 70°C, cooling for 30 min at room temperature; and (c) a repeat of step 2. The results obtained by the three different heating processes of the 3D-printed sinusoidal samples were examined by XRD, DMTA, DSC and the tensile test to obtain the effect of heating or annealing on the structural and mechanical properties. The results show significant changes in structure, crystallinity and thermal and mechanical properties of SMTPU 3D-printed samples due to the heating steps. XRD showed the increase in crystallinity with heating. In DMTA, storage modulus, loss modulus and the tan σ peak position also changed for various heating steps. The DSC result showed that the Tg for different steps of the SMTPU 3D-printed sample remained almost the same at around 51°C. The tensile property of the TPU 3D-printed sinusoidal sample decreased in terms of both load and elongation with increased heating processes, while for the SMTPU 3D-printed sinusoidal sample, the load decreased but elongation increased about 2.5 times.

Mechanical Properties of 3D-Printed Wood-Plastic Composites

2018 ◽  
Vol 777 ◽  
pp. 499-507 ◽  
Author(s):  
Ossi Martikka ◽  
Timo Kärki ◽  
Qing Ling Wu
Keyword(s):  
Mechanical Properties ◽  
Composite Materials ◽  
3D Printing ◽  
Impact Strength ◽  
Polylactic Acid ◽  
Wood Plastic Composite ◽  
Wood Plastic Composites ◽  
Plastic Composite ◽  
Plastic Composites ◽  
3D Printed

3D printing has rapidly become popular in both industry and private use. Especially fused deposition modeling has increased its popularity due to its relatively low cost. The purpose of this study is to increase knowledge in the mechanical properties of parts made of wood-plastic composite materials by using 3D printing. The tensile properties and impact strength of two 3D-printed commercial wood-plastic composite materials are studied and compared to those made of pure polylactic acid. Relative to weight –mechanical properties and the effect of the amount of fill on the properties are also determined. The results indicate that parts made of wood-plastic composites have notably lower tensile strength and impact strength that those made of pure polylactic acid. The mechanical properties can be considered sufficient for low-stress applications, such as visualization of prototypes and models or decorative items.

Algorithm to Reduce Leading and Lagging in Conformal Direct-Print

2018 ◽  
Vol 140 (10) ◽  
Author(s):  
Morteza Vatani ◽  
Faez Alkadi ◽  
Jae-Won Choi
Keyword(s):  
Additive Manufacturing ◽  
3D Printing ◽  
3D Model ◽  
Three Dimensional ◽  
Motion Direction ◽  
B Spline ◽  
And Topology ◽  
Printing System ◽  
3D Printed ◽  
Printed Patterns

A novel additive manufacturing algorithm was developed to increase the consistency of three-dimensional (3D) printed curvilinear or conformal patterns on freeform surfaces. The algorithm dynamically and locally compensates the nozzle location with respect to the pattern geometry, motion direction, and topology of the substrate to minimize lagging or leading during conformal printing. The printing algorithm was implemented in an existing 3D printing system that consists of an extrusion-based dispensing module and an XYZ-stage. A dispensing head is fixed on a Z-axis and moves vertically, while the substrate is installed on an XY-stage and moves in the x–y plane. The printing algorithm approximates the printed pattern using nonuniform rational B-spline (NURBS) curves translated directly from a 3D model. Results showed that the proposed printing algorithm increases the consistency in the width of the printed patterns. It is envisioned that the proposed algorithm can facilitate nonplanar 3D printing using common and commercially available Cartesian-type 3D printing systems.

scholarly journals Effect of temperature on the mechanical properties of 3D-printed PLA tensile specimens

2018 ◽  
Vol 24 (8) ◽  
pp. 1337-1346 ◽  
Author(s):  
Marzio Grasso ◽  
Lyes Azzouz ◽  
Paula Ruiz-Hincapie ◽  
Mauro Zarrelli ◽  
Guogang Ren
Keyword(s):  
Mechanical Properties ◽  
3D Printing ◽  
Mechanical Test ◽  
Optical Microscope ◽  
Middle Part ◽  
Gauge Length ◽  
Effect Of Temperature ◽  
Content Type ◽  
Relevant Effect ◽  
3D Printed

Purpose Recent advancements of 3D printing technology have brought forward the interest for this technique in many engineering fields. This study aims to focus on mechanical properties of the polylactic acid (PLA) feeding material under different thermal conditions for a typical fusion deposition of 3D printer system. Design/methodology/approach Specimens were tested under static loading within the range 20ºC to 60ºC considering different infill orientations. The combined effect of temperature and filament orientation is investigated in terms of constitutive material parameters and final failure mechanisms. The difference between feeding system before and post-3D printing was also assessed by mechanical test on feeding filament to verify the thermal profile during the deposition phase. Findings The results in terms of Young’s modulus, ultimate tensile strength (UTS), strain at failure (εf) and stress at failure (σf) are presented and discussed to study the influence of process settings over the final deposited material. Fracture surfaces have been investigated using an optical microscope to link the phenomenological interpretation of the failure with the micro-mechanical behaviour. Experimental results show a strong correlation between stiffness and strength with the infill orientation and the temperature values. Moreover, a relevant effect is related to deformed geometry of the filament approaching glass transition region of the polymer according to the deposition orientation. Research limitations/implications The developed method can be applied to optimise the stiffness and strength of any 3D-printed composite according to the infill orientation. Practical implications To avoid the failure of specimens outside the gauge length, a previously proposed modification to the geometry was adopted. The geometry has a parabolic profile with a curvature of 1,000 mm tangent to the middle part of the specimen. Originality/value Several authors have reported the stiffness and strength of 3D-printed parts under static and ambient temperature for different build parameters. However, there is a lack of literature on the combination of the latter with the temperature effects on the mechanical properties which this paper covers.

scholarly journals DESIGN OF A 3D-PRINTED THREE-CLAW ROBOTIC GRIPPER END-EFFECTOR

2021 ◽  
Vol 11 (4) ◽  
pp. 70-79
Author(s):  
Dino Dominic Forte Ligutan ◽  
Argel Alejandro Bandala ◽  
Jason Limon Española ◽  
Richard Josiah Calayag Tan Ai ◽  
Ryan Rhay Ponce Vicerra ◽  
...  
Keyword(s):  
3D Printing ◽  
Polylactic Acid ◽  
Grip Force ◽  
Thermoplastic Polyurethane ◽  
Robotic Arm ◽  
End Effector ◽  
Design Considerations ◽  
3D Printed ◽  
Materials Used ◽  
Metal Work

The development of a novel 3D-printed three-claw robotic gripper shall be described in this paper with the goal of incorporating various design considerations. Such considerations include the grip reliability and stability, grip force maximization, wide object grasping capability. Modularization of its components is another consideration that allows its parts to be easily machined and reusable. The design was realized by 3D printing using a combination of tough polylactic acid (PLA) material and thermoplastic polyurethane (TPU) material. In practice, additional tolerances were also considered for 3D printing of materials to compensate for possible expansion or shrinkage of the materials used to achieve the required functionality. The aim of the study is to explore the design and eventually deploy the three-claw robotic gripper to an actual robotic arm once its metal work fabrication is finished.

A physical investigation of dimensional and mechanical characteristics of 3D printed nut and bolt for industrial applications

2022 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Ramesh Chand ◽  
Vishal S. Sharma ◽  
Rajeev Trehan ◽  
Munish Kumar Gupta
Keyword(s):  
Mechanical Properties ◽  
Shear Strength ◽  
3D Printing ◽  
Surface Properties ◽  
3D Printer ◽  
Content Type ◽  
Safety Issues ◽  
Machine Failure ◽  
Sharp Edges ◽  
3D Printed

Purpose A nut bolt joint is a primary device that connects mechanical components. The vibrations cause bolted joints to self-loosen. Created by motors and engines, leading to machine failure, and there may be severe safety issues. All the safety issues and self-loosen are directly and indirectly the functions of the accuracy and precision of the fabricated nut and bolt. Recent advancements in three-dimensional (3D) printing technologies now allow for the production of intricate components. These may be used technologies such as 3D printed bolts to create fasteners. This paper aims to investigate dimensional precision, surface properties, mechanical properties and scanning electron microscope (SEM) of the component fabricated using a multi-jet 3D printer. Design/methodology/approach Multi-jet-based 3D printed nut-bolt is evaluated in this paper. More specifically, liquid polymer-based nut-bolt is fabricated in sections 1, 2 and 3 of the base plate. Five nuts and bolts are fabricated in these three sections. Findings Dimensional inquiry (bolt dimension, general dimensions’ density and surface roughness) and mechanical testing (shear strength of nut and bolt) were carried out throughout the study. According to the ISO 2768 requirements for the General Tolerances Grade, the nut and bolt’s dimensional examination (variation in bolt dimension, general dimensions) is within the tolerance grades. As a result, the multi-jet 3D printing (MJP)-based 3D printer described above may be used for commercial production. In terms of mechanical qualities, when the component placement moves from Sections 1 to 3, the density of the manufactured part decreases by 0.292% (percent) and the shear strength of the nut and bolt decreases by 30%. According to the SEM examination, the density of the River markings, sharp edges, holes and sharp edges increased from Sections 1 to 3, which supports the findings mentioned above. Originality/value Hence, this work enlightens the aspects causing time lag during the 3D printing in MJP. It causes variation in the dimensional deviation, surface properties and mechanical properties of the fabricated part, which needs to be explored.

Effects of post-curing conditions on mechanical properties of 3D printed clear dental aligners

2020 ◽  
Vol 26 (8) ◽  
pp. 1337-1344 ◽  
Author(s):  
Prashant Jindal ◽  
Mamta Juneja ◽  
Divya Bajaj ◽  
Francesco Luke Siena ◽  
Philip Breedon
Keyword(s):  
Mechanical Properties ◽  
3D Printing ◽  
Mechanical Strength ◽  
Financial Burden ◽  
Experimental Studies ◽  
Cost Savings ◽  
Time Duration ◽  
Content Type ◽  
Curing Conditions ◽  
3D Printed

Purpose 3D printing techniques have been widely used for manufacturing complex parts for various dental applications. For achieving suitable mechanical strength, post-cure processing is necessary, where the relative time duration and temperature specification also needs to be defined. The purpose of this study/paper is to assess the effects of post curing conditions and mechanical properties of 3D printed clear dental aligners Design/methodology/approach Dental long-term clear resin material has been used for 3D printing of dental aligners using a Formlabs 3D printer for direct usage on patients. Post-curing conditions have been varied, all of which have been subjected to mechanical compression loading of 1,000 N to evaluate the curing effects on the mechanical strength of the aligners. Findings The experimental studies provide significant insight into both temperatures and time durations that could provide sufficient compressive mechanical strength to the 3D printed clear dental aligners. It was observed that uncured aligners deformed plastically with large deformations under the loading conditions, whereas aligners cured between 400°C–800°C for 15–20 min deformed elastically before fragmenting into pieces after safely sustaining higher compressive loads between 495 N and 666 N. The compressive modulus ratio for cured aligners ranged between 4.46 and 5.90 as compared to uncured aligners. For shorter cure time durations and lower temperature conditions, an appropriate elevated compressive strength was also achieved. Originality/value Based on initial assessments by dental surgeons, suitable customised clear aligners can be designed, printed and cured to the desired levels based on patient’s requirements. This could result in time, energy and unit production cost savings, which ultimately would help to alleviate the financial burden placed on both the health service and their patients.

On effect of chemical-assisted mechanical blending of barium titanate and graphene in PVDF for 3D printing applications

2020 ◽  
pp. 089270572094537
Author(s):  
Ravinder Sharma ◽  
Rupinder Singh ◽  
Ajay Batish
Keyword(s):  
Mechanical Properties ◽  
Barium Titanate ◽  
3D Printing ◽  
Comparative Study ◽  
Process Parameters ◽  
Processing Temperature ◽  
Melt Mixing ◽  
Twin Screw ◽  
3D Printed ◽  
The Comparative Study

The polyvinylidene difluoride + barium titanate (BaTiO3) +graphene composite (PBGC) is one of the widely explored thermoplastic matrix due to its 4D capabilities. The number of studies has been reported on the process parameters of twin-screw extruder (TSE) setup (as mechanical blending technique) for the development of PBGC in 3D printing applications. But, hitherto, little has been reported on chemical-assisted mechanical blending (CAMB) as solution mixing and melt mixing technique combination for preparation of PBGC. In this work, for preparation of PBGC feedstock filaments, CAMB has been used. Also, the effect of process parameters of TSE on the mechanical, dimensional, morphological, and thermal properties of prepared filament of PBGC have been explored followed by 3D printing. Further, a comparative study has been reported for the properties of prepared filaments with mechanically blended composites. Similarly, the mechanical properties of 3D printed parts of chemically and mechanically blended composites have been compared. The results of tensile testing for CAMB of PBGC show that the filament prepared with 15% BaTiO3 is having maximum peak strength 43.00 MPa and break strength 38.73 MPa. The optical microphotographs of the extruded filaments revealed that the samples prepared at 180°C extruder temperature and 60 r/min screw speed have minimum porosity, as compared to filaments prepared at high extruder temperature. Further, the results of the comparative study revealed that the filaments of CAMB composites show better mechanical properties as compared to the filaments of mechanically mixed composites. However, the dimensional properties were almost similar in both cases. It was also found that the CAMB composites have better properties at low processing temperature, whereas mechanically blended composites show better results at a higher temperature. While comparing 3D printed parts, tensile strength of specimens fabricated from CAMB was more than the mechanically blended PBGC.

Sign in / Sign up

Export Citation Format

Share Document