Scan Chain Debug Using Dynamic Lock-In Thermography

2011 ◽  
Author(s):  
L. Forli ◽  
B. Picart ◽  
A. Reverdy ◽  
R. Schlangen
Keyword(s):  
Failure Analysis ◽  
Efficient Solution ◽  
Use Cases ◽  
Thermal System ◽  
Complementary Technique ◽  
Scan Chain ◽  
Lock In

Abstract In this paper, we demonstrate that lock-in thermography (LIT) appears as a key and complementary technique for Failure Analysis across different use cases. Even if the failure requires a complex emulation setup, thanks to a specific capability of our thermal system, this kind of failure can be addressed. In our FA case study, we will show that LIT is a most efficient solution to address a bridge defect located inside a complex logic area, and furthermore that LIT highlights the defect itself and not only the consequences of the defect.

Case Study—Lock-in Thermography Application in Failure Analysis of a System Level DC-DC μModule Regulator

2017 ◽  
Author(s):  
Vikash Kumar ◽  
Devraj Karthikeyan
Keyword(s):  
Heat Source ◽  
Failure Analysis ◽  
Case Studies ◽  
Fault Localization ◽  
System Level ◽  
Thermal Failure ◽  
Analysis Process ◽  
Lock In

Abstract Fault localization is a common failure analysis process that is used to detect the anomaly on a faulty device. The Infrared Lock-In Thermography (LIT) is one of the localization techniques which can be used on the packaged chips for identifying the heat source which is a result of active damage. This paper extends the idea that the LIT analysis for fault localization is not only limited to the devices within the silicon die but it also highlights thermal failure indications of other components on the PCB (like capacitors, FETs etc on a system level DC-DC μmodule). The case studies presented demonstrate the effectiveness of using LIT in the Failure analysis process of a system level DC-DC μmodule regulator

Enhanced Failure Analysis on Open TSV Interconnects

2012 ◽  
Author(s):  
F. Altmann ◽  
C. Schmidt ◽  
J. Beyersdorfer ◽  
M. Simon-Najasek ◽  
C. Große ◽  
...  
Keyword(s):  
Electron Beam ◽  
High Resolution ◽  
Failure Analysis ◽  
Preparation Technique ◽  
Target Preparation ◽  
Material Analysis ◽  
Highly Efficient ◽  
Lock In

Abstract In this paper different methods and novel tools for failure localisation and high resolution material analysis for open TSV interconnects will be discussed. The paper shows the application of enhanced methods for the localisation of sidewall shorts in open TSV structures by adapted Photoemission Microscopy (PEM), Lock-in Thermography (LIT) and Electron Beam Absorbed Imaging (EBAC). In addition, a new highly efficient target preparation technique is presented, which allows the combination of Laser and FIB milling, in order to access TSV sidewall defects. Finally the use of this technique is demonstrated in a failure analysis case study.

Accurate Defect Localization of Stacked Die Devices by Lock-in Thermography

2018 ◽  
Author(s):  
Ke-Ying Lin ◽  
Chih-Yi Tang ◽  
Yu Chi Wang
Keyword(s):  
Failure Analysis ◽  
Defect Modes ◽  
Defect Localization ◽  
Lock In

Abstract The paper demonstrates the moving of lock-in thermography (LIT) spot location by adjusting the lock-in frequency from low to high. Accurate defect localization in stacked-die devices was decided by the fixed LIT spot location after the lock-in frequency was higher than a specific value depending on the depth of the defect in the IC. Physical failure analysis was performed based on LIT results, which provided clear physical defect modes of the stacked-die devices.

Failure Analysis Case Study of a 1.5 Meter Space Flex Harness

2017 ◽  
Author(s):  
Erick Kim ◽  
Kamjou Mansour ◽  
Gil Garteiz ◽  
Javeck Verdugo ◽  
Ryan Ross ◽  
...  
Keyword(s):  
Failure Analysis ◽  
Failure Modes ◽  
Field Of View ◽  
Area Of Interest ◽  
Air Stream ◽  
Novel Method ◽  
Temperature Controlled ◽  
Non Destructive ◽  
Failure Site

Abstract This paper presents the failure analysis on a 1.5m flex harness for a space flight instrument that exhibited two failure modes: global isolation resistances between all adjacent traces measured tens of milliohm and lower resistance on the order of 1 kiloohm was observed on several pins. It shows a novel method using a temperature controlled air stream while monitoring isolation resistance to identify a general area of interest of a low isolation resistance failure. The paper explains how isolation resistance measurements were taken and details the steps taken in both destructive and non-destructive analyses. In theory, infrared hotspot could have been completed along the length of the flex harness to locate the failure site. However, with a field of view of approximately 5 x 5 cm, this technique would have been time prohibitive.

Failure Analysis of CDM-ESD Damage in a GaAs RFIC

2000 ◽  
Author(s):  
Amy Poe ◽  
Steve Brockett ◽  
Tony Rubalcava
Keyword(s):  
Radio Frequency ◽  
Failure Analysis ◽  
Integrated Circuit ◽  
Production Test ◽  
Analysis Techniques ◽  
Device Model ◽  
Charged Device ◽  
Subsequent Failure

Abstract The intent of this work is to demonstrate the importance of charged device model (CDM) ESD testing and characterization by presenting a case study of a situation in which CDM testing proved invaluable in establishing the reliability of a GaAs radio frequency integrated circuit (RFIC). The problem originated when a sample of passing devices was retested to the final production test. Nine of the 200 sampled devices failed the retest, thus placing the reliability of all of the devices in question. The subsequent failure analysis indicated that the devices failed due to a short on one of two capacitors, bringing into question the reliability of the dielectric. Previous ESD characterization of the part had shown that a certain resistor was likely to fail at thresholds well below the level at which any capacitors were damaged. This paper will discuss the failure analysis techniques which were used and the testing performed to verify the failures were actually due to ESD, and not caused by weak capacitors.

A New Deprocess Flow of Failure Analysis for MEMS Motion Sensor

2013 ◽  
Author(s):  
Chun-An Huang ◽  
Han-Yun Long ◽  
King-Ting Chiang ◽  
Li Chuang ◽  
Kevin Tsui
Keyword(s):  
Failure Analysis ◽  
Optical Microscopy ◽  
Motion Sensor ◽  
Thermal System ◽  
Layer By Layer ◽  
Sensor Failure ◽  
Process Flow ◽  
New Process ◽  
Cutting System ◽  
Successful Observation

Abstract This paper demonstrates a new de-process flow for MEMS motion sensor failure analysis, using layer by layer deprocessing to locate defect points. Analysis tools used in this new process flow include IR optical microscopy, thermal system, SEM and a cutting system to de-process of MEMS motion sensor and successful observation defect points.

Advanced IR-OBIRCH Analysis Technique for High Isb Failure Analysis

2010 ◽  
Author(s):  
Kuo Hsiung Chen ◽  
Wen Sheng Wu ◽  
Yu Hsiang Shu ◽  
Jian Chan Lin
Keyword(s):  
Failure Analysis ◽  
Failure Mechanisms ◽  
Fault Localization ◽  
Resistance Change ◽  
The Real ◽  
Analysis Techniques ◽  
Analysis Technique ◽  
Leakage Failure ◽  
Failure Site

Abstract IR-OBIRCH (Infrared Ray – Optical Beam Induced Resistance Change) is one of the main failure analysis techniques [1] [2] [3] [4]. It is a useful tool to do fault localization on leakage failure cases such as poor Via or contact connection, FEoL or BEoL pattern bridge, and etc. But the real failure sites associated with the above failure mechanisms are not always found at the OBIRCH spot locations. Sometimes the real failure site is far away from the OBIRCH spot and it will result in inconclusive PFA Analysis. Finding the real failure site is what matters the most for fault localization detection. In this paper, we will introduce one case using deep sub-micron process generation which suffers serious high Isb current at wafer donut region. In this case study a BEoL Via poor connection is found far away from the OBIRCH spots. This implies that layout tracing skill and relation investigation among OBIRCH spots are needed for successful failure analysis.

The Electrical Characterization and Physical Failure Analysis for Transistor Gate Leakage

2006 ◽  
Author(s):  
Tsung-Te Li ◽  
Chao-Chi Wu ◽  
Jung-Hsiang Chuang ◽  
Jon C. Lee
Keyword(s):  
Failure Analysis ◽  
Electrical Characterization ◽  
Physical Analysis ◽  
Gate Leakage ◽  
Force Microscopy ◽  
Atomic Force ◽  
Transmission Electron ◽  
Voltage Stress ◽  
Leakage Site

Abstract This article describes the electrical and physical analysis of gate leakage in nanometer transistors using conducting atomic force microscopy (C-AFM), nano-probing, transmission electron microscopy (TEM), and chemical decoration on simulated overstressed devices. A failure analysis case study involving a soft single bit failure is detailed. Following the nano-probing analysis, TEM cross sectioning of this failing device was performed. A voltage bias was applied to exaggerate the gate leakage site. Following this deliberate voltage overstress, a solution of boiling 10%wt KOH was used to etch decorate the gate leakage site followed by SEM inspection. Different transistor leakage behaviors can be identified with nano-probing measurements and then compared with simulation data for increased confidence in the failure analysis result. Nano-probing can be used to apply voltage stress on a transistor or a leakage path to worsen the weak point and then observe the leakage site easier.

Application of Lock-in Thermography on PCB for Fault Localization and Validation of Failure Mechanism Due to External Discrete Component Variation

2010 ◽  
Author(s):  
William Ng ◽  
Kevin Weaver ◽  
Zachary Gemmill ◽  
Herve Deslandes ◽  
Rudolf Schlangen
Keyword(s):  
Failure Mechanism ◽  
Integrated Circuit ◽  
Printed Circuit Board ◽  
Hot Spot ◽  
Circuit Board ◽  
Discrete Component ◽  
Printed Circuit ◽  
Thermal Signature ◽  
Lock In

Abstract This paper demonstrates the use of a real time lock-in thermography (LIT) system to non-destructively characterize thermal events prior to the failing of an integrated circuit (IC) device. A case study using a packaged IC mounted on printed circuit board (PCB) is presented. The result validated the failing model by observing the thermal signature on the package. Subsequent analysis from the backside of the IC identified a hot spot in internal circuitry sensitive to varying value of external discrete component (inductor) on PCB.

Case Study in Fault Isolation of a Metal Short for Yield Enhancement

2010 ◽  
Author(s):  
Sarven Ipek ◽  
David Grosjean
Keyword(s):  
Failure Analysis ◽  
Failure Mechanism ◽  
Photon Emission ◽  
Fault Isolation ◽  
Yield Enhancement ◽  
Analysis Technique ◽  
Laser Signal ◽  
Signal Injection ◽  
Microscopy Techniques

Abstract The application of an individual failure analysis technique rarely provides the failure mechanism. More typically, the results of numerous techniques need to be combined and considered to locate and verify the correct failure mechanism. This paper describes a particular case in which different microscopy techniques (photon emission, laser signal injection, and current imaging) gave clues to the problem, which then needed to be combined with manual probing and a thorough understanding of the circuit to locate the defect. By combining probing of that circuit block with the mapping and emission results, the authors were able to understand the photon emission spots and the laser signal injection microscopy (LSIM) signatures to be effects of the defect. It also helped them narrow down the search for the defect so that LSIM on a small part of the circuit could lead to the actual defect.

Sign in / Sign up

Export Citation Format

Share Document