The Cavitation Resistance of WC-10Co4Cr and WC-20CrC-7Ni HVAF Coatings

2021 ◽  
Author(s):  
S. Korobov ◽  
N.V. Lezhnin ◽  
A.V. Makarov ◽  
H.L. Alwan ◽  
V.I. Shumyakov ◽  
...  
Keyword(s):  
Cavitation Erosion ◽  
The Other ◽  
Grain Structure ◽  
Cavitation Resistance ◽  
Pore Density ◽  
Feedstock Powder ◽  
Surface Layers ◽  
Ni Content ◽  
The Matrix ◽  
Coating Microstructure

Abstract Two kinds of cermet powders, WC-10Co4Cr and WC-20CrC-7Ni, were deposited on 1040 steel via high velocity air fuel (HVAF) spraying to evaluate resistance in cavitation erosion conditions with additional electrochemical effects. Coating microstructure, phase composition, and microhardness were examined along with the topography of eroded surface layers. The cavitation resistance of the WC-20CrC-7Ni coating was found to be approximately 1.3 times greater than that of the other coating, which can be attributed to its finer grain structure, lower pore density, and the presence of high Cr and Ni content in the feedstock powder which serves to strengthen the matrix.

scholarly journals Influence of Nitriding and Laser Remelting on Properties of Austenitic Stainless Steel Type X10CrNi18-8 and Cavitation Erosion Resistance

2016 ◽  
Vol 16 (2) ◽  
pp. 21-31
Author(s):  
A. Sitko ◽  
M. Szkodo ◽  
S. Kucharski
Keyword(s):  
Stainless Steel ◽  
Austenitic Stainless Steel ◽  
Cavitation Erosion ◽  
Erosion Resistance ◽  
Nitriding Process ◽  
Cavitation Resistance ◽  
Laser Remelting ◽  
Surface Layers ◽  
Steel Type ◽  
Cavitation Erosion Resistance

Abstract The paper presents properties of surface layers. Surface layers were obtained by using low temperature glow–discharge nitriding process and laser remelting carried out on austenitic stainless steel type X10CrNi18-8. Investigations were done by using an Ultra Nanoindentation Tester (UNHT) in the Warsaw Institute of Fundamental Technological Research. The influence of the above mentioned treatments on obtained surface layers is shown. The values of the Vickers hardness (HV), the irreversible indentation work (Wir), the reversible work (We) and the maximum depth (hmax) during indentation were determined using the method proposed by Oliver and Pharr [1]. On the basis of mechanical properties, the elasticity (Ie) and ductility (Iir) indexes were calculated. Moreover, microstructure cross-section of the austenitic stainless steel after nitriding process and laser remelting was observed using a scanning electron microscope. Cavitation test was performed at a vibratory rig with stationary specimen. On the basis of erosion curves the cavitation resistance was evaluated.

Pembobotan Berdasarkan Tingkat Kesamaan Semantik pada Metode Fuzzy Semi-Supervised Co-Clustering untuk Pengelompokkan Dokumen Teks

2014 ◽  
Vol 6 (2) ◽  
pp. 46-51
Author(s):  
Galang Amanda Dwi P. ◽  
Gregorius Edwadr ◽  
Agus Zainal Arifin
Keyword(s):  
Supervised Learning ◽  
Semantic Similarity ◽  
The Other ◽  
Classification Result ◽  
Document Similarity ◽  
The Matrix ◽  
Index Terms ◽  
Membership Value ◽  
Degree Of Similarity

Nowadays, a large number of information can not be reached by the reader because of the misclassification of text-based documents. The misclassified data can also make the readers obtain the wrong information. The method which is proposed by this paper is aiming to classify the documents into the correct group.  Each document will have a membership value in several different classes. The method will be used to find the degree of similarity between the two documents is the semantic similarity. In fact, there is no document that doesn’t have a relationship with the other but their relationship might be close to 0. This method calculates the similarity between two documents by taking into account the level of similarity of words and their synonyms. After all inter-document similarity values obtained, a matrix will be created. The matrix is then used as a semi-supervised factor. The output of this method is the value of the membership of each document, which must be one of the greatest membership value for each document which indicates where the documents are grouped. Classification result computed by the method shows a good value which is 90 %. Index Terms - Fuzzy co-clustering, Heuristic, Semantica Similiarity, Semi-supervised learning.

Ni Content Surface Layer Produced by Laser Surface Treatment on Amorphisable Cu Base Alloy

2010 ◽  
Vol 649 ◽  
pp. 101-106
Author(s):  
Mária Svéda ◽  
Dóra Janovszky ◽  
Kinga Tomolya ◽  
Jenő Sólyom ◽  
Zoltán Kálazi ◽  
...  
Keyword(s):  
Surface Layer ◽  
Surface Treatment ◽  
Laser Cladding ◽  
Base Alloy ◽  
Laser Surface ◽  
Laser Alloying ◽  
Laser Surface Treatment ◽  
Ni Content ◽  
Wide Range ◽  
The Matrix

The aim of our research was to comparatively examine Ni content surface layers on amorphisable Cu base alloy produced by different laser surface treatments. Laser surface treatment (LST) techniques, such as laser surface melting, laser alloying and laser cladding, provide a wide range of interesting solutions for the production of wear and corrosion resistant surfaces. [1,2] With LST techniques, the surface can be: i) coated with a layer of another material by laser cladding, ii) the composition of the matrix can be modified by laser alloying. [3] Two kinds of laser surface treatment technologies were used. In the case of coating-melting technology a Ni content surface layer was first developed by galvanization, and then the Ni content layer was melted together with the matrix. In the case of powder blowing technology Ni3Al powder was blown into the layer melted by laser beam and Argon gas. LST was performed using an impulse mode Nd:YAG laser. The laser power and the interaction time were 2 kW and 20÷60 ms. The characterization of the surface layer microstructure was performed by XRD, scanning electron microscopy and microhardness measurements.

Matrix-Mineral Relationships-A. Morphologist's Viewpoint

1979 ◽  
Vol 58 (2_suppl) ◽  
pp. 922-929 ◽  
Author(s):  
M.U. Nylen
Keyword(s):  
Organic Material ◽  
Crucial Role ◽  
Crystal Surface ◽  
Organic Matrix ◽  
The Other ◽  
Enamel Matrix ◽  
Initial Cell ◽  
Cell Product ◽  
Ultrastructural Morphology ◽  
The Matrix

The literature on the ultrastructural morphology of the enamel matrix and its relationship to the crystals is reviewed. Two morphological entities of the matrix are discussed: One is the so-called stippled material which may be the initial cell product; the other, variously described as fibrillar, lamellar, tubular or helical, is thought by many to play a crucial role in nucleation and orientation of the crystals. A number of observations, however, suggest that the latter structures form secondarily to the crystals and that in reality they represent organic material adsorbed to the crystal surface and maintained as independent structures upon removal of the mineral. The need for additional studies is stressed including systematic studies of interactions between constituents of the organic matrix and the apatite crystals.

Modeling the Irradiation Swelling of UO2 at the Fuel Pellet Rim

2013 ◽  
Author(s):  
Lijun Gao ◽  
Bingde Chen ◽  
Zhong Xiao ◽  
Shengyao Jiang ◽  
Jiyang Yu
Keyword(s):  
Pore Size ◽  
Fission Products ◽  
Transformation Process ◽  
Fuel Pellet ◽  
Published Data ◽  
Detailed Calculation ◽  
Pore Density ◽  
The Matrix ◽  
Swelling Rate ◽  
Modeling Code

Irradiation swelling of UO2 at the fuel pellet rim was modeled based on the published theory and data of HBS (High Burnup Structure) formation. Fuel swelling was divided into two parts: fuel matrix swelling and porosity growth. Both solid fission products and fission gas contribute to the fuel matrix swelling prior to HBS transformation, resulting in relatively stable matrix swelling rate of around 1.0% per 10 GWd/tU, but the transformation accompanied by Xe depletion reduces the matrix swelling rate to approximately 0.3% per 10 GWd/tU, only attributed to solid fission products. Considering the direct impact of Xe depletion on the drop of matrix swelling rate, the exponential law of Xe depletion was applied to model the reduction of matrix swelling rate. Pore size and pore density evolution are the two main aspects of porosity growth. Pore size takes the form of lognormal distribution, whose parameters are obtained through fitting the experimental data. Pore density increases in the transformation process but goes down as a result of pore coarsening thereafter. Published data of three pellets were used to verify the correlations modeling pore growth, which were proven generally consistent with each other. The results of this work are ready to be incorporated into fuel performance modeling code as an option for detailed calculation of fuel swelling.

Soil water dynamics after fire in a Portuguese shrubland

2006 ◽  
Vol 15 (1) ◽  
pp. 99 ◽  
Author(s):  
Joaquim S. Silva ◽  
Francisco C. Rego ◽  
Stefano Mazzoleni
Keyword(s):  
Water Content ◽  
Soil Water ◽  
Plant Community ◽  
Root Distribution ◽  
Control Plot ◽  
The Other ◽  
Water Dynamics ◽  
Soil Water Dynamics ◽  
Surface Layers ◽  
Before And After

This paper presents a study where soil water content (SW) was measured before and after an experimental fire in a shrubland dominated by Erica scoparia L. in Portugal. Two plots were established: one was kept as a control plot and the other was burned by an experimental fire in June 2001. Measurements were taken before fire (2000), and after fire (2001, 2002, and 2003) at six depths down to 170 cm, from June to December. Measurements before fire allowed comparison of the two plots in terms of the SW differential, using 2000 as a reference. Results for 2001 showed that SW decreased less during the drying season (June–September) and increased more during the wetting season (October–December) in the burned plot than in the control plot. The magnitude of these effects decreased consistently in 2002 and 2003, especially at surface layers. The maximum gain of SW for the total profile in the burned plot was estimated as 105.5 mm in 2001, 70.2 mm in 2002, and 35.6 mm in 2003. The present paper discusses the mechanisms responsible for the increase in SW taking into account the characteristics of the plant community, including the root distribution, and the results of other studies.

A Yield Criterion of Porous Materials With Anisotropy Caused by Geometry or Distribution of Pores

1991 ◽  
Vol 113 (4) ◽  
pp. 425-429 ◽  
Author(s):  
T. Hisatsune ◽  
T. Tabata ◽  
S. Masaki
Keyword(s):  
Velocity Field ◽  
Porous Materials ◽  
Upper Bound ◽  
Volume Fraction ◽  
Yield Criterion ◽  
Longitudinal Direction ◽  
Axisymmetric Deformation ◽  
The Other ◽  
The Matrix ◽  
Spherical Cells

Axisymmetric deformation of anisotropic porous materials caused by geometry of pores or by distribution of pores is analyzed. Two models of the materials are proposed: one consists of spherical cells each of which has a concentric ellipsoidal pore; and the other consists of ellipsoidal cells each of which has a concentric spherical pore. The velocity field in the matrix is assumed and the upper bound approach is attempted. Yield criteria are expressed as ellipses on the σm σ3 plane which are longer in longitudinal direction with increasing anisotropy and smaller with increasing volume fraction of the pore. Furthermore, the axes rotate about the origin at an angle α from the σm-axis, while the axis for isotropic porous materials is on the σm-axis.

Wounded by reality: emotional deprivation and unresolved trauma in psychoanalytical couple’s therapy

2021 ◽  
Vol 15 (2) ◽  
pp. 253-268
Author(s):  
Hélène Béïnoglou
Keyword(s):  
Romantic Relationships ◽  
Emotional Experience ◽  
Therapeutic Process ◽  
Clinical Work ◽  
The Other ◽  
The Matrix ◽  
Emotional Deprivation ◽  
Unresolved Trauma

In this article, I will focus on highly conflictual couples with extensive emotional deprivation and unresolved trauma, which prevents them from developing healthy romantic relationships and overcoming the challenges entailed in any intimate attachment. I will describe how everyday interactions are experienced as threatening or even lethal movements between the partners. The question which arises in the psychoanalytical therapeutic process is how to help the couple tolerate the sensory reminders of the unresolved trauma as a necessary precursor to any process of symbolisation. In order to provide a safe enough therapeutic attachment bond, extensive time is dedicated to the emotional experience of self and the other in the here-and-now of the session, which validates the emotional experience of the couple as well as contains it. The therapy focuses on the transferential and countertransferential movements inspired by the matrix of the victim, abuser, and uninvolved witness (Davies & Frawley, 1994) to elaborate the intertwining of the unresolved trauma with the couple’s form of attachment. In order to illustrate my argument, I present two examples: one from a fictional narration and another from my clinical work.

Design of a novel HSLA steel with a combination of high strength (140–160 ksi) and excellent toughness

2021 ◽  
Vol 112 (10) ◽  
pp. 800-811
Author(s):  
Mehdi Soltan Ali Nezhad ◽  
Sadegh Ghazvinian ◽  
Mahmoud Amirsalehi ◽  
Amir Momeni
Keyword(s):  
Impact Toughness ◽  
Yield Strength ◽  
Hsla Steel ◽  
Charpy Impact ◽  
High Strength ◽  
Controlled Rolling ◽  
The Other ◽  
Grain Structure ◽  
Charpy Impact Toughness ◽  
Fine Grain

Abstract Three steels were designed based on HSLA-100 with additional levels of Mn, Ni, Cr and Cu. The steels were prepared by controlled rolling and tempered at temperatures in range of 550–700°C. The continuous cooling time curves were shifted to longer times and lower temperatures with the increased tendency for the formation of martensite at lower cooling rates. The microstructures revealed that controlled rolling results in austenite with uniform fine grain structure. The steel with the highest amount of Mn showed the greatest strength after tempering at 750 °C. The top strength was attributed to the formation of Cu-rich particles. The steel with 1.03 wt.% Mn, tempered at 650 °C exhibited the best Charpy impact toughness at –85°C. On the other hand, the steel that contained 2.11 wt.% Mn and tempered at 700 °C showed the highest yield strength of 1 097.5 MPa (∼159 ksi) and an impact toughness of 41.6 J at –85°C.

Sign in / Sign up

Export Citation Format

Share Document