scholarly journals Study on Dust Control Technology in Artillery Working Face

2021 ◽  
Author(s):  
Changfu Zou
Keyword(s):  
Wind Speed ◽  
High Efficiency ◽  
Diffusion Path ◽  
Dust Control ◽  
Prevention Measures ◽  
Working Face ◽  
Reduction Efficiency ◽  
Reduction Effect ◽  
Mining Work ◽  
Dust Reduction

Aiming at the serious problem of dust pollution in blasting work, the dust generation law and dust-bearing air flow time and space evolution law of blasting working face is analyzed and studied, and the optimal dust-exhausting wind speed of blasting work was 1.5 m/s. Combining with the dust production characteristics and wind speed conditions of the 107 blasting face in Dongling Coal Mine, Chongqing, Comprehensive dust prevention measures such as high-efficiency water cannon mud, high-pressure spray dust reduction, and dust concentration over-limit spray dust reduction are adopted to control the dust from the source and cut off the dust diffusion path, and the total dust reduction efficiency reached 94.8%, the respirable dust reduction efficiency reached 92%, and a good dust reduction effect has been achieved, which provides a basic basis for the control of dust in the blast mining work.

scholarly journals Researches on the numerical simulation of the dust pollution characteristics and the optimal dust suppression wind-speed on fully mechanised caving face

2021 ◽  
pp. 014459872110558
Author(s):  
Jinming Mo ◽  
Wei Ma
Keyword(s):  
Numerical Simulation ◽  
Wind Speed ◽  
Wind Velocity ◽  
Mass Concentration ◽  
Dust Control ◽  
Dust Pollution ◽  
Dust Suppression ◽  
Working Face ◽  
Dust Mass ◽  
Wind Velocities

Dust removal by ventilation is a commonly used dust control strategy. This study analyses the characteristics of airflow transport and dust pollution on a fully mechanised top-coal caving face at different inlet wind velocities by using a numerical simulation experiment, and the best wind velocity for dust suppression is obtained. When the inlet wind velocity fluctuates in the range of 0.5 to 3.0 m/s, the overall dust mass concentration on the working face initially increases and then remains stable, but in the range of 2.5 to 3.0 m/s, the changes in the overall dust mass concentration and dust mass concentration of the respiratory zone on the working face are not significant. The dust pollution in the respiratory zone produced by the hydraulic support lowering pillar and moving frame on the working face is quantitatively analysed at different inlet wind velocities of 2.5 to 3.0 m/s to determine the optimum wind velocity for dust suppression on the working face. The optimum wind speed for dust suppression is 2.6 m/s. This study lays a foundation for the ventilation design and dust control in the early stage of a mine and for the establishment of a clean and green production mine.

scholarly journals Study on the Atomization and Dust-Reduction Performance of a New Type of External Pneumatic Vortex Fog Curtain Dust Removal Device in Fully Mechanized Excavation Face

2020 ◽  
Vol 2020 ◽  
pp. 1-15
Author(s):  
Deji Jing ◽  
Rina An ◽  
Jingxu Chen ◽  
Shaocheng Ge ◽  
Liying Sun
Keyword(s):  
Wind Speed ◽  
Dust Removal ◽  
Air Volume ◽  
Reduction Experiment ◽  
Reduction Efficiency ◽  
New Type ◽  
Atomization Performance ◽  
Relationship Of ◽  
Atomization Pressure ◽  
Dust Reduction

To solve the problem of dust pollution in the heading face, a new type of external pneumatic vortex fog curtain dust removal device suitable for a fully mechanized excavation face is designed in this paper. Firstly, dust migration laws at different times are simulated and analyzed by COMSOL software, and the functional relationship of dust concentration distribution above 50 mg/m3 at different heights and different wind speed is derived. Aiming at the dust migration laws of the heading face, a new dust removal device was proposed, and the atomization performance of the new type of external pneumatic vortex fog curtain dust removal device under different jet wind speed, different atomization pressure, and different nozzle working angle is explored through atomization performance experiment. It is found that when jet wind speed is 30 m/s, atomization pressure is 4 MPa, and nozzle working angle is 75°, the atomization performance of the new type of external pneumatic vortex fog curtain dust removal device is the best. Through the simulation of COMSOL software, the influence of air volume on the new type of external pneumatic vortex fog curtain dust removal device is analyzed. It is found that the new type of external pneumatic vortex fog curtain dust removal device is relatively stable when the air volume at the pressure outlet is less than 400 m3/min. The dust-reduction efficiency of the new type of external pneumatic vortex fog curtain dust removal device was investigated through the dust-reduction experiment, and it is found that the new type of external pneumatic vortex fog curtain dust removal device had better dust removal performance under the condition that the ventilation conditions did not interfere with the integrity of the vortex fog curtain.

scholarly journals Photocatalytic reduction of graphene oxide with cuprous oxide film under UV-vis irradiation

2020 ◽  
Vol 59 (1) ◽  
pp. 207-214 ◽  
Author(s):  
Yao Wang ◽  
Jianqing Feng ◽  
Lihua Jin ◽  
Chengshan Li
Keyword(s):  
Graphene Oxide ◽  
Photoelectron Spectroscopy ◽  
Low Cost ◽  
Photocatalytic Reduction ◽  
Force Microscopy ◽  
Atomic Force ◽  
Reduced Graphene ◽  
Reduction Efficiency ◽  
Metal Organic ◽  
Reduction Effect

AbstractWe have grown Cu2O films by different routes including self-oxidation and metal-organic deposition (MOD). The reduction efficiency of Cu2O films on graphene oxide (GO) synthesized by modified Hummer’s method has been studied. Surface morphology and chemical state of as-prepared Cu2O film and GO sheets reduced at different conditions have also been investigated using atomic force microscopy (AFM) and x-ray photoelectron spectroscopy (XPS). Results show that self-oxidation Cu2O film is more effective on phtocatalytic reduction of GO than MOD-Cu2O film. Moreover, reduction effect of self-oxidation Cu2O film to GO is comparable to that of environmental-friendly reducing agent of vitamin C. The present results offer a potentially eco-friendly and low-cost approach for the manufacture of reduced graphene oxide (RGO) by photocatalytic reduction.

Investigation on dust dispersion during support movement in a fully mechanized mining face and the technology with support frame enclosure dust control

2021 ◽  
pp. 095440892110311
Author(s):  
Jinming Mo ◽  
Wei Ma ◽  
Dandan Li ◽  
Sheji Zhang
Keyword(s):  
Wind Speed ◽  
Field Application ◽  
Dust Concentration ◽  
Dust Control ◽  
Average Wind Speed ◽  
Dust Source ◽  
Air Inlet ◽  
Support Frame ◽  
Site Field ◽  
Mining Face

A fully mechanized mining face is characterized by serious dust pollution and dust is a major cause of pneumoconiosis that haunts numerous miners. For a fully mechanized face having large mining heights, the main dust source in the pavement area is produced by the moving support frame. To reduce the amount of dust during support's movement, the distribution and dissipation of dust in this process were studied by combining numerical simulations with underground measurements. The results showed that with an increase of the distance from the air inlet, the wind speed of the sidewalk in the fully mechanized face first increased, then decreased, and finally increased again. At the position of the coal cutter, the highest wind speed was 1.78 m/s and the average wind speed of the roadway was about 0.8 m/s. The dust concentration at the dust source was >1000 mg/m3. An area with a high dust concentration and having a length of 15 m was formed on the rooftop, together with a 50 m long dust belt with a dust concentration of 300 to 450 mg/m3 in the pavement area of 10 m from the dust source. Beyond the 45 m radius from the dust source, the dust concentration was stable at about 250 mg/m3. Based on the dust production characteristics of the support frame, an enclosed dust-guiding device was designed and structure-optimized. Based on the on-site field application test results, it was found that the device has a satisfactory dust-guiding effect during support movement and the dust suppression rate near the dust source reached 94.8%.

scholarly journals Numerical Simulation and Engineering Application of Coalbed Water Injection

2019 ◽  
Vol 2019 ◽  
pp. 1-12 ◽  
Author(s):  
Yijie Shi ◽  
Pengfei Wang ◽  
Ronghua Liu ◽  
Xuanhao Tan ◽  
Wen Zhang
Keyword(s):  
Numerical Simulation ◽  
Process Parameters ◽  
Water Injection ◽  
Engineering Application ◽  
Working Environment ◽  
Engineering Practice ◽  
Characteristic Parameters ◽  
Injection Process ◽  
Working Face ◽  
Dust Reduction

Coalbed water injection is the most basic and effective dust-proof technology in the coal mining face. To understand the influence of coalbed water injection process parameters and coalbed characteristic parameters on coal wetting radius, this paper uses Fluent computational fluid dynamics software to systematically study the seepage process of coalbed water injection under different process parameters and coalbed characteristic parameters, calculation results of which are applied to engineering practice. The results show that the numerical simulation can help to predict the wetness range of coalbed water injection, and the results can provide guidance for the onsite design of coalbed water injection process parameters. The effect of dust reduction applied to onsite coalbed water injection is significant, with the average dust reduction rates during coal cutting and support moving being 67.85% and 46.07%, respectively, which effectively reduces the dust concentration on the working face and improves the working environment.

scholarly journals Airflow Characteristics According to the Change in the Height and Porous Rate of Building Roofs for Efficient Installation of Small Wind Power Generators

2021 ◽  
Vol 13 (10) ◽  
pp. 5688
Author(s):  
Jangyoul You ◽  
Kipyo You ◽  
Minwoo Park ◽  
Changhee Lee
Keyword(s):  
Wind Speed ◽  
Wind Power ◽  
Turbulence Intensity ◽  
Flow Characteristics ◽  
High Porosity ◽  
Power Generators ◽  
Speed Reduction ◽  
Reduction Effect ◽  
Wind Power Generators ◽  
The Impact

In this paper, the air flow characteristics and the impact of wind power generators were analyzed according to the porosity and height of the parapet installed in the rooftop layer. The wind speed at the top was decreasing as the parapet was installed. However, the wind speed reduction effect was decreasing as the porosity rate increased. In addition, the increase in porosity significantly reduced turbulence intensity and reduced it by up to 40% compared to no railing. In the case of parapets with sufficient porosity, the effect of reducing turbulence intensity was also increased as the height increased. Therefore, it was confirmed that sufficient parapet height and high porosity reduce the effect of reducing wind speed by parapets and significantly reducing the turbulence intensity, which can provide homogeneous wind speed during installation of wind power generators.

scholarly journals Determination of Long Horizontal Borehole Height in Roofs and its Application to Gas Drainage

Energies ◽  
2018 ◽  
Vol 11 (10) ◽  
pp. 2647
Author(s):  
Gang Wang ◽  
Cheng Fan ◽  
Hao Xu ◽  
Xuelin Liu ◽  
Rui Wang
Keyword(s):  
Numerical Simulation ◽  
Theoretical Model ◽  
Fracture Zone ◽  
Coalbed Methane ◽  
High Efficiency ◽  
Gas Drainage ◽  
Methane Drainage ◽  
Working Face ◽  
Variation Characteristics

Accurately determining the height of the gas-guiding fracture zone in the overlying strata of the goaf is the key to find the height of the long horizontal borehole in the roof. In order to determine the height, in this study we chose the 6306 working face of Tangkou Coal Mine in China as a research example and used both the theoretical model and discrete element method (DEM) numerical simulation to find the height of the gas-guiding fracture zone and applied the height to drill a long horizontal borehole in the roof of the 6303 working face. Furthermore, the borehole was utilized to deep into the roof for coalbed methane drainage and the results were compared with conventional gas drainage measures from other aspects. The height of the gas-guiding fracture zone was found to be 48.57 m in theoretical model based on the bulk coefficient and the void ratio and to be 51.19 m in the DEM numerical simulation according to the temporal and spatial variation characteristics of porosity. Taking both the results of theoretical analysis and numerical simulation into consideration, we determined that gas-guiding fracture zone is 49.88 m high and applied it to drill a long horizontal borehole deep into the roof in the 6303 working face field. Compared with conventional gas drainage measures, we found that the long horizontal borehole has the high stability, high efficiency and strong adaptability for methane drainage.

scholarly journals Study on the Efficiency and Dynamic Characteristics of an Energy Harvester Based on Flexible Structure Galloping

Energies ◽  
2021 ◽  
Vol 14 (20) ◽  
pp. 6548
Author(s):  
Peng Liao ◽  
Jiyang Fu ◽  
Wenyong Ma ◽  
Yuan Cai ◽  
Yuncheng He
Keyword(s):  
Numerical Simulation ◽  
Wind Speed ◽  
Physical Model ◽  
Energy Harvester ◽  
High Efficiency ◽  
Lateral Displacement ◽  
Maximum Output Power ◽  
Flexible Structure ◽  
Maximum Output ◽  
Cfd Numerical Simulation

According to the engineering phenomenon of the galloping of ice-coated transmission lines at certain wind speeds, this paper proposes a novel type of energy harvester based on the galloping of a flexible structure. It uses the tension generated by the galloping structure to cause periodic strain on the piezoelectric cantilever beam, which is highly efficient for converting wind energy into electricity. On this basis, a physical model of fluid–structure interaction is established, and the Reynolds-averaged Navier–Stokes equation and SST K -ω turbulent model based on ANSYS Fluent are used to carry out a two-dimensional steady computational fluid dynamics (CFD) numerical simulation. First, the CFD technology under different grid densities and time steps is verified. CFD numerical simulation technology is used to simulate the physical model of the energy harvester, and the effect of wind speed on the lateral displacement and aerodynamic force of the flexible structure is analyzed. In addition, this paper also carries out a parameterized study on the influence of the harvester’s behavior, through the wind tunnel test, focusing on the voltage and electric power output efficiency. The harvester has a maximum output power of 119.7 μW/mm3 at the optimal resistance value of 200 KΩ at a wind speed of 10 m/s. The research results provide certain guidance for the design of a high-efficiency harvester with a square aerodynamic shape and a flexible bluff body.

scholarly journals Mechanism and Prevention and Control of Mine Earthquake in Thick and Hard Rock Strata considering the Horizontal Stress Evolution of Stope

2021 ◽  
Vol 2021 ◽  
pp. 1-14
Author(s):  
Ming Zhang ◽  
Xuelong Hu ◽  
Hongtao Huang ◽  
Guangyao Chen ◽  
Shan Gao ◽  
...  
Keyword(s):  
Hard Rock ◽  
Design Method ◽  
Horizontal Stress ◽  
Prevention Measures ◽  
Stress Concentrations ◽  
Estimation Model ◽  
Working Face ◽  
Mining Design ◽  
And Control ◽  
Rock Strata

This study investigated the mechanism, prevention measures, and control methods for earthquake disasters typically occurring in mines with thick and hard rock strata. A mine stope with large faults and thick hard rock strata in Hebei Province was taken as the background study object. Then, theoretical analysis and numerical simulation methods were adopted in conjunction with field monitoring to explore how horizontal stress evolves in the thick and hard hanging roofs of such mines, potentially leading to mining earthquakes. Then, based on the obtained results, a mining design method was proposed to reduce the horizontal stress levels of earthquake mitigation. The results showed that, under the control of large faults, semiopen and semiclosed stopes with thick hard rock strata are formed, which cause influentially pressurized and depressurized zones during the evolution of the overburden movements and horizontal stress. It was determined that the stress concentrations mainly originated from the release and transfer of horizontal stress during the rock fractures and movements in the roof areas, which were calculated using a theoretical estimation model. The horizontal stress concentrations formed “counter torques” at both ends of the thick and hard strata, which prevented the support ending due to tensile failures. As a result, the limit spans were increased. This study proposed a mining strategy of using narrow working faces, strip mining processes, and reasonable mining speeds, which could effectively reduce horizontal stress concentrations and consequently prevent and control mining earthquakes. This study’s research results were successfully applied to the mining practices in working face 16103.

Sign in / Sign up

Export Citation Format

Share Document