scholarly journals Influence of Ag interlayer Thickness on the Optical, Electrical and Mechanical Properties of Ti-doped In2O3/Ag/Ti-doped In2O3 Multilayer Flexible Transparent Conductive Electrode

2021 ◽  
Vol 59 (8) ◽  
pp. 545-550
Author(s):  
Su-Hyeon Choe ◽  
Jin-Kyu Jang ◽  
Hyun-Jin Kim ◽  
Jae-Wook Choi ◽  
Sung-Bo Heo ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Sheet Resistance ◽  
Single Layer ◽  
Rf Magnetron Sputtering ◽  
Xrd Analysis ◽  
Multilayer Films ◽  
Electrical Performance ◽  
Interlayer Thickness ◽  
Transparent Conductive Electrode ◽  
High Flexibility

Transparent and conductive Ti-doped In2O3 (TIO)/Ag/Ti-doped In2O3 (TAT) multilayer films were deposited on colorless poly imide (CPI) substrates by direct current (DC) and radio frequency (RF) magnetron sputtering at room temperature. During deposition the thickness of both the top and bottom TIO layer was fixed at 30 nm, while the thickness of the Ag interlayer was varied, to 5, 10, and 15 nm, to enhance the optical, electrical and mechanical properties of the films. In the XRD analysis the TIO films did not show any characteristic peaks in the diffraction pattern. The 10 nm thick Ag inter layer showed some characteristic peaks of Ag (111), (200), (220) and (311), respectively, and the grain size of the Ag interlayer enlarged as Ag thickness increased. To investigate the most efficient Ag interlayer thickness, a figure of merit (FOM) based on the opto-electrical performance of the transparent conducting films was compared. The films with a 10 nm thick Ag interlayer exhibited a higher FOM of 1.71 × 10-2 Ω-1 than the other films. When the radius of the film's curvature was reduced to 1.7 mm, the TIO single layer films showed a 13 times increase in sheet resistance, while the TAT (30/10/30 nm) films showed an insignificant change in sheet resistance. From the observed results, it was concluded that the Ag interlayer in the TAT multilayer films enhanced the opto-electrical performance of the films and also acted as a potent bridge which assured the high flexibility endurance of the films.

Transparent Electrodes From Graphene/Single Wall Carbon Nanotube Composites

2013 ◽  
Author(s):  
Hossein Sojoudi ◽  
Fernando Reiter ◽  
Samuel Graham
Keyword(s):  
Electrical Properties ◽  
Sheet Resistance ◽  
Composite Films ◽  
Single Layer ◽  
Chemical Vapor ◽  
Optical Transmittance ◽  
Single Layer Graphene ◽  
Atmospheric Conditions ◽  
Transparent Conductive Electrode ◽  
Nanotube Composites

A transparent conductive electrode comprised of alternating layers of graphene grown by chemical vapor deposition (CVD) and metallic single wall nanotubes (M-SWNTs) is presented. It was found that the addition of two single-layer graphene sheets enhances the conduction pathways in the M-SWNT film, yielding up to a 75% decrease in the sheet resistance with little sacrifice in the optical transmittance. Enhancements in the electrical properties of the films were made through a heat treatment process followed by nitric acid and thionyl chloride doping, yielding a sheet resistance of 70 Ω/sq with a transmittance of 78% at 550 nm. Composite films having undergone an annealing step were found to have stable electrical properties upon exposure to atmospheric conditions while doped films demonstrated limited stability.

Cracking at the fold in double layer coated paper: the influence of latex and starch composition

TAPPI Journal ◽  
2019 ◽  
Vol 18 (2) ◽  
pp. 93-99
Author(s):  
SEYYED MOHAMMAD HASHEMI NAJAFI ◽  
DOUGLAS BOUSFIELD, ◽  
MEHDI TAJVIDI
Keyword(s):  
Mechanical Properties ◽  
Double Layer ◽  
Starch Content ◽  
Single Layer ◽  
Double Layers ◽  
Coated Paper ◽  
Coated Papers ◽  
Coating Layers ◽  
Scanned Images ◽  
Packaging Paper

Cracking at the fold of publication and packaging paper grades is a serious problem that can lead to rejection of product. Recent work has revealed some basic mechanisms and the influence of various parameters on the extent of crack area, but no studies are reported using coating layers with known mechanical properties, especially for double-coated systems. In this study, coating layers with different and known mechanical properties were used to characterize crack formation during folding. The coating formulations were applied on two different basis weight papers, and the coated papers were folded. The binder systems in these formulations were different combinations of a styrene-butadiene latex and mixtures of latex and starch for two different pigment volume concentrations (PVC). Both types of papers were coated with single and double layers. The folded area was scanned with a high-resolution scanner while the samples were kept at their folded angle. The scanned images were analyzed within a constant area. The crack areas were reported for different types of papers, binder system and PVC values. As PVC, starch content, and paper basis weight increased, the crack area increased. Double layer coated papers with high PVC and high starch content at the top layer had more cracks in comparison with a single layer coated paper, but when the PVC of the top layer was low, cracking area decreased. No measurable cracking was observed when the top layer was formulated with a 100% latex layer.

Ab Initio Calculation of Mechanical Properties of Stacking Fault in 3C-SiC: Effect of Stress and Doping

2012 ◽  
Vol 717-720 ◽  
pp. 415-418
Author(s):  
Yoshitaka Umeno ◽  
Kuniaki Yagi ◽  
Hiroyuki Nagasawa
Keyword(s):  
Mechanical Properties ◽  
Ab Initio ◽  
Density Functional ◽  
Stacking Faults ◽  
Single Layer ◽  
Local Strain ◽  
Density Functional Theory Calculations ◽  
Stacking Fault ◽  
Functional Theory ◽  
N Doping

We carry out ab initio density functional theory calculations to investigate the fundamental mechanical properties of stacking faults in 3C-SiC, including the effect of stress and doping atoms (substitution of C by N or Si). Stress induced by stacking fault (SF) formation is quantitatively evaluated. Extrinsic SFs containing double and triple SiC layers are found to be slightly more stable than the single-layer extrinsic SF, supporting experimental observation. Effect of tensile or compressive stress on SF energies is found to be marginal. Neglecting the effect of local strain induced by doping, N doping around an SF obviously increase the SF formation energy, while SFs seem to be easily formed in Si-rich SiC.

scholarly journals Composite Material of PDMS with Interchangeable Transmittance: Study of Optical, Mechanical Properties and Wettability

2021 ◽  
Vol 5 (4) ◽  
pp. 110
Author(s):  
Flaminio Sales ◽  
Andrews Souza ◽  
Ronaldo Ariati ◽  
Verônica Noronha ◽  
Elder Giovanetti ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Experimental Study ◽  
Room Temperature ◽  
Casting Process ◽  
Optical Characteristics ◽  
Smart Devices ◽  
Superhydrophobic Coating ◽  
Gravity Casting ◽  
High Flexibility ◽  
Physical And Chemical

Polydimethylsiloxane (PDMS) is a polymer that has attracted the attention of researchers due to its unique properties such as transparency, biocompatibility, high flexibility, and physical and chemical stability. In addition, PDMS modification and combination with other materials can expand its range of applications. For instance, the ability to perform superhydrophobic coating allows for the manufacture of lenses. However, many of these processes are complex and expensive. One of the most promising modifications, which consists of the development of an interchangeable coating, capable of changing its optical characteristics according to some stimuli, has been underexplored. Thus, we report an experimental study of the mechanical and optical properties and wettability of pure PDMS and of two PDMS composites with the addition of 1% paraffin or beeswax using a gravity casting process. The composites’ tensile strength and hardness were lower when compared with pure PDMS. However, the contact angle was increased, reaching the highest values when using the paraffin additive. Additionally, these composites have shown interesting results for the spectrophotometry tests, i.e., the material changed its optical characteristics when heated, going from opaque at room temperature to transparent, with transmittance around 75%, at 70 °C. As a result, these materials have great potential for use in smart devices, such as sensors, due to its ability to change its transparency at high temperatures.

scholarly journals Analysis of Different Complex Multilayer PACVD Coatings on Nanostructured WC-Co Cemented Carbide

Coatings ◽  
2021 ◽  
Vol 11 (7) ◽  
pp. 823
Author(s):  
Danko Ćorić ◽  
Mateja Šnajdar Musa ◽  
Matija Sakoman ◽  
Željko Alar
Keyword(s):  
Mechanical Properties ◽  
Surface Layer ◽  
Base Material ◽  
Single Layer ◽  
Production Costs ◽  
Structural Defects ◽  
Cemented Carbides ◽  
Material System ◽  
Tin Coating ◽  
Ticn Coating

The development of cemented carbides nowadays is aimed at the application and sintering of ultrafine and nano-sized powders for the production of a variety of components where excellent mechanical properties and high wear resistance are required for use in high temperature and corrosive environment conditions. The most efficient way of increasing the tribological properties along with achieving high corrosion resistance is coating. Using surface processes (modification and/or coating), it is possible to form a surface layer/base material system with properties that can meet modern expectations with acceptable production costs. Three coating systems were developed on WC cemented carbides substrate with the addition of 10 wt.% Co using the plasma-assisted chemical vapor deposition (PACVD) method: single-layer TiN coating, harder multilayer gradient TiCN coating composed of TiN and TiCN layers, and the hardest multilayer TiBN coating composed of TiN and TiB2. Physical and mechanical properties of coated and uncoated samples were investigated by means of quantitative depth profile (QDP) analysis, nanoindentation, surface layer characterization (XRD analysis), and coating adhesion evaluation using the scratch test. The results confirm the possibility of obtaining nanostructured cemented carbides of homogeneous structure without structural defects such as eta phase or unbound carbon providing increase in hardness and fracture toughness. The lowest adhesion was detected for the single-layer TiN coating, while coatings with a complex architecture (TiCN, TiBN) showed improved adhesion.

scholarly journals Mineralogical Composition and Physical–Mechanical Properties of Dasht-E-Taatrang Zar Sand Deposits (Afghanistan)

2020 ◽  
Vol 5 (1) ◽  
pp. 2
Author(s):  
Hemayatullah Ahmadi ◽  
Atal Yousufi ◽  
Amir Mohammad Mosazai
Keyword(s):  
Mechanical Properties ◽  
Construction Material ◽  
Mineralogical Composition ◽  
Xrd Analysis ◽  
Sample Collection ◽  
Extensive Field ◽  
Chemical And Mineralogical Composition ◽  
New City ◽  
Two Phases ◽  
Field Works

Sand is a common construction material used for various purposes, e.g., concrete, mortar, render, screed, and asphalt. The usage depends on its fineness, and its fineness is controlled by its mineralogical composition and physical-mechanical properties. This research aims to determine the chemical and mineralogical composition and the physical-mechanical properties of the Dasht-e-Taatrang Zar sand deposits within the Qarabagh and Bagram districts of Kabul and Parwan provinces in Afghanistan. To achieve the objectives of this research, a review of the existing literature has been combined with new extensive field works for macroscopic studies and sample collection, and laboratory analyses. In total, 23 samples during two phases of field works were collected and subjected to lab works for XRF, Schlich, and XRD analysis to determine the chemical and mineralogical composition; moreover, sieve and Atterberg analysis, specific gravity, soundness, and alkali-silica reaction tests were performed for characterization of the physical-mechanical properties of the studied samples. The results of the tests show that the Taatrang Zar sand deposits are considered as a suitable construction material, and due to their simple accessibility, the deposits have high potential as a construction material supplier for the Kabul new city project (Dehsabz) in Kabul and adjacent Parwan and Kapisa provinces.

The Mechanical Properties Comparative Analysis for Socked and Non-Socketed Composite Pile

2014 ◽  
Vol 1061-1062 ◽  
pp. 748-750
Author(s):  
Heng Chen ◽  
Ke Sheng Ma
Keyword(s):  
Mechanical Properties ◽  
Comparative Analysis ◽  
Seismic Performance ◽  
Dynamic Loads ◽  
Vertical Load ◽  
Interlayer Thickness ◽  
Static Loads ◽  
Soil Stress ◽  
Composite Pile ◽  
Static And Dynamic Loads

For socked and non-socketed piles in the different mechanical behavior under static and dynamic loads, the paper use ABAQUS to model, simulate the pile , the soil interlayer thickness between the bottom of the pile and bedrock are 2m, 4m under vertical load and Earthquake, cushion cap, pile and pile soil stress situation found non-socketed piles when the soil interlayer thickness within a certain range, the composite pile small subside under dynamic, static loads, the non-socketed piles can better take advantage of the pile soil has a good seismic performance in the earthquake.

Effects of Welding Wire Composition on Microstructure and Mechanical Properties of Welded Joint in Al-Mg-Si Alloy

2022 ◽  
Vol 905 ◽  
pp. 44-50
Author(s):  
Li Wang ◽  
Ya Ya Zheng ◽  
Shi Hu Hu
Keyword(s):  
Mechanical Properties ◽  
Fusion Zone ◽  
Heat Affected Zone ◽  
Welded Joint ◽  
Weld Zone ◽  
Xrd Analysis ◽  
Metallographic Analysis ◽  
Strengthening Effect ◽  
Welding Wire ◽  
Microstructure And Mechanical Properties

The effects of welding wire composition on microstructure and mechanical properties of welded joint in Al-Mg-Si alloy were studied by electrochemical test, X-ray diffraction (XRD) analysis and metallographic analysis. The results show that the weld zone is composed of coarse columnar dendrites and fine equated grains. Recrystallized grains are observed in the fusion zone, and the microstructure in the heat affected zone is coarsened by welding heat. The hardness curve of welded joint is like W-shaped, the highest hardness point appears near the fusion zone, and the lowest hardness point is in the heat affected zone. The main second phases of welded joints are: matrix α-Al, Mg2Si, AlMnSi, elemental Si and SiO2. The addition of rare earth in welding wire can refine the grain in weld zone obviously, produce fine grain strengthening effect, and improve the electrochemical performance of weld.

Manufacture of thin rice straw particleboards bonded with various polymeric methane diphenyl diisocyanate/ urea formaldehyde resin mixtures

BioResources ◽  
2019 ◽  
Vol 15 (1) ◽  
pp. 935-944
Author(s):  
Peng Luo ◽  
Chuanmin Yang ◽  
Mengyao Li ◽  
Yueqi Wang
Keyword(s):  
Mechanical Properties ◽  
Rice Straw ◽  
Water Resistance ◽  
Urea Formaldehyde ◽  
Single Layer ◽  
Formaldehyde Resin ◽  
Manufacturing Cost ◽  
Board Density ◽  
Layer Medium ◽  
Resin Formulation

Reducing particleboard thickness is one of the major approaches to decrease consumption volume of particleboard for furniture manufacture. This study employed an adhesive mixture of polymeric methane diphenyl diisocyanate (PMDI) and urea formaldehyde (UF) to produce single-layer medium density thin rice straw particleboard. The effects of various PMDI/UF formulations as well as board density on mechanical properties and water resistance of rice straw particleboard were studied. The results indicated that the mechanical properties and water resistance of the thin rice straw particleboard were appreciably affected by resin formulation. The panels bonded with PMDI/UF adhesive mixtures had mechanical properties and water resistance far superior to those bonded with UF. Higher PMDI content levels in resin mixtures led to improved mechanical properties and water resistance. Density influenced mechanical properties and water resistance of the thin rice straw particleboard. Increasing the density of the panel could upgrade the mechanical properties of the thin rice straw particleboard. The experimental outcomes showed that PMDI/UF resin systems had potential to substitute for pure PMDI resin in producing thin rice straw particleboard, which could effectively lower manufacturing cost and bring economic efficiencies due to reduced amount of pricey PMDI.

Sign in / Sign up

Export Citation Format

Share Document