scholarly journals Laser Induced Method to Produce Curcuminoid-Silanol Thin Films for Transdermal Patches Using Irradiation of Turmeric Target

2021 ◽  
Vol 11 (9) ◽  
pp. 4030
Author(s):  
Alexandru Cocean ◽  
Iuliana Cocean ◽  
Nicanor Cimpoesu ◽  
Georgiana Cocean ◽  
Ramona Cimpoesu ◽  
...  
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Pulsed Laser ◽  
Thin Layers ◽  
Silver Layer ◽  
Transdermal Patch ◽  
Laser Technique ◽  
Silanol Groups ◽  
Hemp Fabric ◽  
532 Nm

A new possible method to produce a transdermal patch is proposed in this paper. The study refers to the pulsed laser deposition method (PLD) applied on turmeric target in order to obtain thin layers. Under high power laser irradiation of 532 nm wavelength, thin films containing curcuminoids were obtained on different substrates such as glass and quartz (laboratory investigation) and hemp fabric (practical application). Compared FTIR, SEM-EDS and LIF analyses proved that the obtained thin film chemical composition is mainly demethoxycurcumin and bisdemethoxycurcumin which is evidence that most of the curcumin from turmeric has been demethixylated during laser ablation. Silanol groups with known role into dermal reconstruction are evidenced in both turmeric target and curcuminoid thin films. UV–VIS reflection spectra show the same characteristics for all the curcuminoid thin films, indicating that the method is reproducible. The method proves to be successful for producing a composite material, namely curcuminoid transdermal patch with silanol groups, using directly turmeric as target in the thin film deposited by pulsed laser technique. Double layered patch curcuminoid—silver was produced under this study, proving compatibility between the two deposited layers. The silver layer added on curcuminoid-silanol layer aimed to increase antiseptic properties to the transdermal patch.

Evaluation of Planar-Type Thin Film ZnO Varistors Fabricated Using Pulsed Laser Ablation

2006 ◽  
Vol 320 ◽  
pp. 109-112
Author(s):  
Sayuki Sawa ◽  
Shinzo Yoshikado
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Laser Ablation ◽  
Pulsed Laser ◽  
Pulsed Laser Ablation ◽  
Alumina Substrate ◽  
Laser Ablation Method ◽  
Zno Varistors ◽  
532 Nm ◽  
Deposited Films

Planar-type thin film Bi-Mn-Co-doped ZnO varistors were fabricated on a silica glass substrate or a sintered alumina substrate using a visible light (532 nm) pulsed laser ablation method. The deposited thin films were annealed at 800°C or 900°C in air. For the thin films deposited on alumina substrates and then annealed, the contents of Bi and Mn decreased compared with those of the as-deposited films. Voltage-current (V-I) characteristics of the thin-film varistor fabricated on the alumina substrates and annealed showed nonlinearity. The nonlinearity index α was approximately 10 for the thin film deposited on the alumina substrate and annealed at 800°C in air using a target of ZnO doped with 2.5 mol% Bi2O3, 0.5 mol% MnO2 and 0.2 mol% Co3O4. Moreover, the current density of 20 A/cm3 was relatively high for safety use.

Observations on the growth of YBa2Cu3O7-δ thin films on MgO by pulsed-laser ablation

1991 ◽  
Vol 49 ◽  
pp. 1068-1069
Author(s):  
M. Grant Norton ◽  
C. Barry Carter
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Laser Ablation ◽  
Substrate Surface ◽  
Pulsed Laser ◽  
Pulsed Laser Ablation ◽  
Thin Film Deposition ◽  
Film Deposition ◽  
Laser Ablation Process ◽  
Deposition Parameters

Pulsed-laser ablation has been widely used to produce high-quality thin films of YBa2Cu3O7-δ on a range of substrate materials. The nonequilibrium nature of the process allows congruent deposition of oxides with complex stoichiometrics. In the high power density regime produced by the UV excimer lasers the ablated species includes a mixture of neutral atoms, molecules and ions. All these species play an important role in thin-film deposition. However, changes in the deposition parameters have been shown to affect the microstructure of thin YBa2Cu3O7-δ films. The formation of metastable configurations is possible because at the low substrate temperatures used, only shortrange rearrangement on the substrate surface can occur. The parameters associated directly with the laser ablation process, those determining the nature of the process, e g. thermal or nonthermal volatilization, have been classified as ‘primary parameters'. Other parameters may also affect the microstructure of the thin film. In this paper, the effects of these ‘secondary parameters' on the microstructure of YBa2Cu3O7-δ films will be discussed. Examples of 'secondary parameters' include the substrate temperature and the oxygen partial pressure during deposition.

scholarly journals Deposition pressure-induced microstructure control and plasmonic property tuning in hybrid ZnO-AgxAu1-x thin films

2021 ◽  
Author(s):  
Robynne Lynne PALDI ◽  
Xing Sun ◽  
Xin Li Phuah ◽  
Juanjuan Lu ◽  
Xinghang Zhang ◽  
...  
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Pulsed Laser Deposition ◽  
Pulsed Laser ◽  
Laser Deposition ◽  
Deposition Method ◽  
Hybrid Films ◽  
Deposition Pressure ◽  
Plasmonic Metamaterials ◽  
Film Form

Self-assembled oxide-metallic alloyed nanopillars as hybrid plasmonic metamaterials (e.g., ZnO-AgxAu1-x) in a thin film form are grown using a pulsed laser deposition method. The hybrid films were demonstrated to be...

The Dielectric Properties of Pb0.65Ba0.35ZrO3 Thin Films

2006 ◽  
Vol 306-308 ◽  
pp. 1313-1318
Author(s):  
J.S. Kim ◽  
B.H. Park ◽  
T.J. Choi ◽  
Se Hyun Shin ◽  
Jae Chul Lee ◽  
...  
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Dielectric Properties ◽  
Dielectric Loss ◽  
Deposition Temperature ◽  
Pulsed Laser ◽  
Laser Deposition ◽  
Axis Orientation ◽  
Capacitance Voltage ◽  
Bst Thin Film

Pb0.65Ba0.35ZrO3 (PBZ) thin films have been grown on MgO (001) substrates by pulsed-laser deposition (PLD). We have compared the structural and dielectric properties of PBZ films grown at various temperatures. A highly c-axis orientation has appeared at PBZ film grown at the deposition temperature of 550oC. The c-axis oriented PBZ film has also shown the largest tunability among all the PBZ films in capacitance-voltage measurements. The tunability and dielectric loss of the PBZ film was 20% and 0.00959, respectively. In addition, we have compared the temperature coefficient of capacitance (TCC) of a PBZ film with that of a Ba0.5Sr0.5TiO3 (BST) film which is a well-known material applicable to tunable microwave devices. We have confirmed that TCC value of a PBZ thin film was three-times smaller than that of a BST thin film.

Pulsed Laser Deposition (PLD) Technique to Prepare Biocompatible Thin Films

2006 ◽  
Vol 49 ◽  
pp. 56-61 ◽  
Author(s):  
Joseph J. Beltrano ◽  
Lorenzo Torrisi ◽  
Anna Maria Visco ◽  
Nino Campo ◽  
E. Rapisarda
Keyword(s):  
Thin Films ◽  
Pulsed Laser ◽  
Target Material ◽  
Xrd Analysis ◽  
Spot Size ◽  
Laser Deposition ◽  
Laser Source ◽  
Medical Field ◽  
Hot Plasma ◽  
532 Nm

A Nd:YAG laser is employed to ablate different materials useful in the bio-medical field. The laser source operates in the IR (1064 nm), VIS (532 nm) and UV (355 nm) regions with a pulse duration of 3-9 ns, a pulse energy of 3-300 mJ, a spot size of 1 mm2 and a repetition rate of 1- 30 Hz. Target material of interest are Titanium, Carbon, Hydroxyapatite (HA) and Polyethylene (PE). Laser irradiation occurs in vacuum, where hot plasma is generated, and thin films are deposited on near substrates. Generally, substrates of silicon, titanium, titanium-alloys and polymers were employed. Biocompatible thin films are investigated with different surface techniques, such as IR spectroscopy, Raman spectroscopy, XRD analysis and SEM investigations. Depending of the kind of possible application, films require special properties concerning the grain size, porosity, uniformity, wetting, hardness, adhesion, crystallinity and composition. The obtained results will be presented and discussed with particular regard to HA..

scholarly journals Binary Metal Oxides Thin Films Prepared from Pulsed Laser Deposition

2021 ◽  
Author(s):  
Cyril Robinson Azariah John Chelliah ◽  
Rajesh Swaminathan
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Metal Oxide ◽  
Metal Oxides ◽  
Pulsed Laser ◽  
Primary Objective ◽  
Binary Oxides ◽  
Binary Metal ◽  
Metal Oxide Nanostructures ◽  
Binary Metal Oxide

The semiconductor industry flourished from a simple Si-based metal oxide semiconductor field effect transistor to an era of MOSFET-based smart materials. In recent decades, researchers have been replacing all the materials required for the MOSFET device. They replaced the substrate with durable materials, lightweight materials, translucent materials and so on. They have came up with the possibility of replacing dielectric silicon dioxide material with high-grade dielectric materials. Even then the channel shift in the MOSFET was the new trend in MOSFET science. From the bulk to the atomic level, transistors have been curiously researched across the globe for the use of electronic devices. This research was also inspired by the different semiconductor materials relevant to the replacement of the dielectric channel/gate. Study focuses on diverse materials such as zinc oxides (ZnO), electrochromic oxides such as molybdenum oxides (including MoO3 and MoO2) and other binary oxides using ZnO and MoO3. The primary objective of this research is to study pulsed laser deposited thin films such as ZnO, MoO3, binary oxides such as binary ZnO /MoO3, ZnO /TiO2 and ZnO/V2O5 and to analyse their IV properties for FET applications. To achieve the goal, the following working elements have been set: investigation of pulsed laser deposited thin film of metal oxides and thin film of binary metal oxide nanostructures with effects of laser repetition and deposition temperatures.

scholarly journals The Study of Optical and Electrical Properties of Nanostructured Silicon Carbide Thin Films Grown by Pulsed-Laser Deposition

2021 ◽  
Vol 9 (2) ◽  
pp. 46-50
Author(s):  
Muhanad A. Ahmed ◽  
Mohammed F. Mohammed Sabri ◽  
Wathiq R. Abed
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Silicon Carbide ◽  
Absorption Coefficient ◽  
Pulsed Laser Deposition ◽  
Extinction Coefficient ◽  
Pulsed Laser ◽  
Laser Deposition ◽  
Cutoff Wavelength ◽  
Nanostructured Silicon

In this paper, nanostructured silicon carbide (SiC) thin films are deposited onto glass substrate using pulsed laser deposition technique. Electrical and optical characterizations such as conductivity, resistivity, transmission, Seeback effect, absorption, absorption coefficient, energy band gap, and extinction coefficient as a function of photon energy, and the effect of thin films thickness on transmission are carried out to characterize the prepared samples. Results showed that the prepared SiC thin film is an n-type semiconductor with an indirect bandgap of ~3 eV, 448 nm cutoff wavelength, 3.4395 × 104 cm−1 absorption coefficient and 0.154 extinction coefficient. The surface morphology of the SiC thin films is studied using scanning electron microscope at a substrate temperature of 400 °C and it is found that the grain size of the prepared SiC thin film is about 30 nm. As such, the nano thin films optical and structural characteristics enable the films to be used as gases sensors in many optoelectronic devices such as the environment and ultraviolet photodiode.

Preparation and Characterization of MFM and MFIS Structures Using Sr2(Ta1划x, Nbx)2O7 Thin Film by Pulsed Laser Deposition

2000 ◽  
Vol 655 ◽  
Author(s):  
Masanori Okuyama ◽  
Toshiyuki Nakaiso ◽  
Minoru Noda
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Pulsed Laser Deposition ◽  
Pulsed Laser ◽  
Ferroelectric Thin Films ◽  
Laser Deposition ◽  
Polarization Reversal ◽  
Ambient Gas ◽  
Mfis Structure

AbstractSr2(Ta1划x, Nbx)2O7(STN) ferroelectric thin films have been prepared on SiO2/Si(100) substrates by the pulsed laser deposition (PLD) method. Preferential (110) and (151)-oriented STN thin films are deposited at a low temperature of 600°C in N2O ambient gas at 0.08 Torr. A counterclockwise C-V hysteresis was observed in the metal-ferroelectric-insulator-semiconductor (MFIS) structure using Sr2(Ta0.7, Nb0.3)2O7 on SiO2/Si deposited at 600°C. Memory window in the C-V curve spreads symmetrically towards both positive and negative directions when applied voltage increases and the window does not change in sweep rates ranging from 0.1 to 4.0×103 V/s. The C-V curve of the MFIS structure does not degrade after 1010 cycles of polarization reversal. The gate retention time is about 3.0×103 sec when the voltages and time of write pulse are ±15V and 1.0 sec, respectively, and hold bias was -0.5 V.

scholarly journals The Properties of Zn-Doped AlSb Thin Films Prepared by Pulsed Laser Deposition

Coatings ◽  
2019 ◽  
Vol 9 (2) ◽  
pp. 136
Author(s):  
Ping Tang ◽  
Weimin Wang ◽  
Bing Li ◽  
Lianghuan Feng ◽  
Guanggen Zeng
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Pulsed Laser Deposition ◽  
Band Gap ◽  
Photovoltaic Effect ◽  
Pulsed Laser ◽  
Laser Deposition ◽  
Sem Images ◽  
Glass Substrates ◽  
Substrate Temperatures

Aluminum antimony (AlSb) is a promising photovoltaic material with a band gap of about 1.62 eV. However, AlSb is highly deliquescent and not stable, which has brought great difficulties to the applications. Based on the above situation, there are two purposes for preparing our Zn-doped AlSb (AlSb:Zn) thin films: One is to make P-type AlSb and the other is to find a way to suppress the deliquescence of AlSb. The AlSb:Zn thin films were prepared on glass substrates at different substrate temperatures by using the pulsed laser deposition (PLD) method. The structural, surface morphological, optical, and electrical properties of AlSb:Zn films were investigated. The crystallization of AlSb:Zn thin films was enhanced and the electrical resistivity decreased as the substrate temperature increased. The scanning electron microscopy (SEM) images indicated that the grain sizes became bigger as the substrate temperatures increased. The Raman vibration mode AlSb:Zn films were located at ~107 and ~142 cm−1 and the intensity of Raman peaks was stronger at higher substrate temperatures. In the experiment, a reduced band gap (1.4 eV) of the AlSb:Zn thin film was observed compared to the undoped AlSb films, which were more suitable for thin-film solar cells. Zn doping could reduce the deliquescent speed of AlSb thin films. The fabricated heterojunction device showed the good rectification behavior, which indicated the PN junction formation. The obvious photovoltaic effect has been observed in an FTO/ZnS/AlSb:Zn/Au device.

Pulsed Laser Deposited Oxide Green Emitting Thin Film Phosphors : Optimization of Growth Conditions

2006 ◽  
Vol 988 ◽  
Author(s):  
P. Thiyagarajan ◽  
M. Kottaismay ◽  
M S Ramachandra Rao
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Oxygen Partial Pressure ◽  
Partial Pressure ◽  
Diffuse Reflectance Spectroscopy ◽  
Quartz Substrate ◽  
Pulsed Laser ◽  
Growth Conditions ◽  
Ex Situ ◽  
Morphological Studies

AbstractStructural and photoluminescence (PL) properties of Zn2(1-x)MnxSiO4 (1 ≤ x ≤ 5) and diffuse reflectance spectroscopy (DRS) and morphological studies of ZnGa2O4:Mn thin film green emitting phosphors grown using pulsed laser deposition (PLD) technique have been investigated. Zn2(1-x)MnxSiO4 thin films grown on Si substrate at 700°C in 300 mTorr of oxygen partial pressure, upon ex-situ annealing at higher temperatures exhibit superior PL intensity. ZnGa2O4:Mn phosphor thin films grown on quartz substrate at 650oC and in-situ annealed in 300mTorr of oxygen partial pressure show better emission intensity. For both Zn2SiO4:Mn and ZnGa2O4:Mn phosphors, luminescence can be assigned to 4T1 – 6A1 transition of Mn2+ within the 3d orbital giving rise to emission at 525 and 503 nm, respectively.

Sign in / Sign up

Export Citation Format

Share Document