scholarly journals Microencapsulated Phase Changing Materials for Gypsum Plasters: A Practical Approach

2021 ◽  
Vol 1 (3) ◽  
pp. 188-202
Author(s):  
Vincent Claude ◽  
Stéphane Charron ◽  
Fabrice de Barquin ◽  
Inge Dirkx
Keyword(s):  
Mechanical Properties ◽  
The Other ◽  
Practical Approach ◽  
Thermal Potential ◽  
Gypsum Plaster ◽  
European Standards

Several studies have shown the feasibility and thermal potential of gypsum plaster with microspheres of PCM, but very few of them investigated an approach with practical and standards concern. In this work, different characterizations are performed according to European standards on a standard gypsum plaster and two different gypsum plasters formulated with 20 wt.% of PCM microspheres. A material is experimentally made by mixing conventional gypsum and PCM microspheres, whereas the other is an already prepared commercial mix. For the laboratory material, the addition of PCM increases the consistency of the fresh paste of plaster. In order to reach a consistency in agreement with the standards more water is required. This higher amount of water causes further issues on the densification and cohesion properties. In contrary, the properties of the commercial mix are closer to a common plaster. It is therefore assumed that the commercial material incorporates thinner additives. In view of these results, it is assumed that most of the drawbacks due to the addition of PCM microspheres in gypsum plasters could effectively be encountered by adequate addition of additives in order to reduce the amount of water, and binding resins in order to improve the adhesion and mechanical properties.

Physical and Mechanical Properties of Tenun Pahang Fabrics using Alternative Yarns

2016 ◽  
Vol 13 (2) ◽  
pp. 67
Author(s):  
Engku Liyana Zafirah Engku Mohd Suhaimi ◽  
Jamil Salleh ◽  
Suzaini Abd Ghani ◽  
Mohamad Faizul Yahya ◽  
Mohd Rozi Ahmad
Keyword(s):  
Mechanical Properties ◽  
Physical And Mechanical Properties ◽  
The Other ◽  
Silk Fabrics ◽  
Recovery Angle ◽  
Made In

An investigation on the properties of Tenun Pahang fabric performances using alternative yarns was conducted. The studies were made in order to evaluate whether the Tenun Pahang fabric could be produced economically and at the same time maintain the fabric quality. Traditional Tenun Pahang fabric uses silk for both warp and weft. For this project, two alternative yarns were used which were bamboo and modal, which were a little lower in cost compared to silk. These yarns were woven with two variations, one with the yarns as weft only while maintaining the silk warp and the other with both warp and weft using the alternative yarns. Four (4) physical testings and three (3) mechanical testings conducted on the fabric samples. The fabric samples were evaluated including weight, thickness, thread density, crease recovery angle, stiffness and drapability. The results show that modal/silk and bamboo silk fabrics are comparable in terms of stiffness and drapability, hence they have the potential to replace 100% silk Tenun Pahang.

scholarly journals Eco-Friendly, High-Density Fiberboards Bonded with Urea-Formaldehyde and Ammonium Lignosulfonate

Polymers ◽  
2021 ◽  
Vol 13 (2) ◽  
pp. 220
Author(s):  
Petar Antov ◽  
Viktor Savov ◽  
Ľuboš Krišťák ◽  
Roman Réh ◽  
George I. Mantanis
Keyword(s):  
Mechanical Properties ◽  
Bending Strength ◽  
Urea Formaldehyde ◽  
Physical And Mechanical Properties ◽  
High Density ◽  
Thickness Swelling ◽  
Formaldehyde Content ◽  
Uf Resin ◽  
Natural Wood ◽  
European Standards

The potential of producing eco-friendly, formaldehyde-free, high-density fiberboard (HDF) panels from hardwood fibers bonded with urea-formaldehyde (UF) resin and a novel ammonium lignosulfonate (ALS) is investigated in this paper. HDF panels were fabricated in the laboratory by applying a very low UF gluing factor (3%) and ALS content varying from 6% to 10% (based on the dry fibers). The physical and mechanical properties of the fiberboards, such as water absorption (WA), thickness swelling (TS), modulus of elasticity (MOE), bending strength (MOR), internal bond strength (IB), as well as formaldehyde content, were determined in accordance with the corresponding European standards. Overall, the HDF panels exhibited very satisfactory physical and mechanical properties, fully complying with the standard requirements of HDF for use in load-bearing applications in humid conditions. Markedly, the formaldehyde content of the laboratory fabricated panels was extremely low, ranging between 0.7–1.0 mg/100 g, which is, in fact, equivalent to the formaldehyde release of natural wood.

scholarly journals Influence of artificial aging: mechanical and physicochemical properties of dental composites under static and dynamic compression

2021 ◽  
Author(s):  
D. C. Gornig ◽  
R. Maletz ◽  
P. Ottl ◽  
M. Warkentin
Keyword(s):  
Mechanical Properties ◽  
Water Sorption ◽  
Artificial Aging ◽  
Filler Content ◽  
Dynamic Compression ◽  
The Other ◽  
Chemical Degradation ◽  
Dental Composites ◽  
Compression Tests ◽  
Acid Ph

Abstract Objective The aim of the study was to evaluate the influence of filler content, degradation media and time on the mechanical properties of different dental composites after in vitro aging. Materials and Methods Specimens (1 mm3) of three commercially available composites (GrandioSO®, Arabesk Top®, Arabesk Flow®) with respect to their filler content were stored in artificial aging media: artificial saliva, ethanol (60%), lactic acid (pH 5) and citric acid (pH 5). Parameters (Vickers microhardness, compressive strength, elastic modulus, water sorption and solubility) were determined in their initial state (control group, n = 3 for microhardness, n = 5 for the other parameters) and after 14, 30, 90 and 180 days (n = 3 for microhardness, n = 5 for the other parameters for each composite group, time point and media). Specimens were also characterized with dynamic-mechanical-thermal analysis (compression tests, F =  ± 7 N; f = 0.5 Hz, 1 Hz and 3.3 Hz; t = 0–170 °C). Results Incorporation of fillers with more than 80 w% leads to significantly better mechanical properties under static and dynamic compression tests and a better water sorption behavior, even after chemical degradation. The influence of degradation media and time is of subordinate importance for chemical degradation. Conclusion Although the investigated composites have a similar matrix, they showed different degradation behavior. Since dentine and enamel occur only in small layer thickness, a test specimen geometry with very small dimensions is recommended for direct comparison. Moreover, the use of compression tests to determine the mechanical parameters for the development of structure-compatible and functionally adapted composites makes sense as an additional standard. Clinical relevance Preferential use of highly filled composites for occlusal fillings is recommended.

scholarly journals The Effect of Different Annealing Strategies on the Microstructure Development and Mechanical Response of Austempered Steels

Metals ◽  
2021 ◽  
Vol 11 (7) ◽  
pp. 1041
Author(s):  
Eliseo Hernandez-Duran ◽  
Luca Corallo ◽  
Tanya Ros-Yanez ◽  
Felipe Castro-Cerda ◽  
Roumen H. Petrov
Keyword(s):  
Mechanical Properties ◽  
Retained Austenite ◽  
Mechanical Response ◽  
Steel Grade ◽  
The Other ◽  
Microstructure Development ◽  
Microstructural Refinement ◽  
Heterogeneous Distribution ◽  
Parent Austenite ◽  
Conventional Annealing

This study focuses on the effect of non-conventional annealing strategies on the microstructure and related mechanical properties of austempered steels. Multistep thermo-cycling (TC) and ultrafast heating (UFH) annealing were carried out and compared with the outcome obtained from a conventionally annealed (CA) 0.3C-2Mn-1.5Si steel. After the annealing path, steel samples were fast cooled and isothermally treated at 400 °C employing the same parameters. It was found that TC and UFH strategies produce an equivalent level of microstructural refinement. Nevertheless, the obtained microstructure via TC has not led to an improvement in the mechanical properties in comparison with the CA steel. On the other hand, the steel grade produced via a combination of ultrafast heating annealing and austempering exhibits enhanced ductility without decreasing the strength level with respect to TC and CA, giving the best strength–ductility balance among the studied steels. The outstanding mechanical response exhibited by the UFH steel is related to the formation of heterogeneous distribution of ferrite, bainite and retained austenite in proportions 0.09–0.78–0.14. The microstructural formation after UFH is discussed in terms of chemical heterogeneities in the parent austenite.

Ultrapurified Alginate Gel Containing Bone Marrow Aspirate Concentrate Enhances Cartilage and Bone Regeneration on Osteochondral Defects in a Rabbit Model

2021 ◽  
pp. 036354652110141
Author(s):  
Liang Xu ◽  
Atsushi Urita ◽  
Tomohiro Onodera ◽  
Ryosuke Hishimura ◽  
Takayuki Nonoyama ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Bone Marrow ◽  
Cell Transplantation ◽  
Cartilage Repair ◽  
Subchondral Bone ◽  
Bone Repair ◽  
Bone Marrow Aspirate ◽  
Defect Group ◽  
The Other ◽  
Osteochondral Defects

Background: Ultrapurified alginate (UPAL) gel implantation has been demonstrated as effective in cartilage repair for osteochondral defects; however, cell transplantation within UPAL gels would be required to treat larger defects. Hypothesis: The combination of UPAL gel and bone marrow aspirate concentrate (BMAC) would enhance cartilage repair and subchondral bone repair for large osteochondral defects. Study Design: Controlled laboratory study. Methods: A total of 104 osteochondral defects (1 defect per knee) of 52 rabbits were randomly divided into 4 groups (26 defects per group): defects without any treatment (Defect group), defects treated using UPAL gel alone (UPAL group), defects treated using UPAL gel containing allogenic bone marrow mesenchymal stromal cells (UPAL-MSC group), and defects treated using UPAL gel containing BMAC (UPAL-BMAC group). At 4 and 16 weeks postoperatively, macroscopic and histologic evaluations and measurements of repaired subchondral bone volumes of reparative tissues were performed. Collagen orientation and mechanical properties of the reparative tissue were assessed at 16 weeks. Results: The defects in the UPAL-BMAC group were repaired with hyaline-like cartilage with well-organized collagen structures. The histologic scores at 4 weeks were significantly higher in the UPAL-BMAC group (16.9 ± 2.0) than in the Defect group (4.7 ± 1.9; P < .05), the UPAL group (10.0 ± 3.3; P < .05), and the UPAL-MSC group (12.2 ± 2.9; P < .05). At 16 weeks, the score in the UPAL-BMAC group (24.4 ± 1.7) was significantly higher than those in the Defect group (9.0 ± 3.7; P < .05), the UPAL group (14.2 ± 3.9; P < .05), and the UPAL-MSC group (16.3 ± 3.6; P < .05). At 4 and 16 weeks, the macroscopic evaluations were significantly superior in the UPAL-BMAC group compared with the other groups, and the values of repaired subchondral bone volumes in the UPAL-BMAC group were significantly higher than those in the Defect and UPAL groups. The mechanical properties of the reparative tissues were significantly better in the UPAL-BMAC group than in the other groups. Conclusion: The implantation of UPAL gel containing BMAC-enhanced hyaline-like cartilage repair and subchondral bone repair of osteochondral defects in a rabbit knee model. Clinical Relevance: These data support the potential clinical application of 1-step treatment for large osteochondral defects using biomaterial implantation with cell transplantation.

scholarly journals Effects of water absorption on the mechanical properties of hybrid natural fibre/phenol formaldehyde composites

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Sekar Sanjeevi ◽  
Vigneshwaran Shanmugam ◽  
Suresh Kumar ◽  
Velmurugan Ganesan ◽  
Gabriel Sas ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Impact Strength ◽  
Water Absorption ◽  
Hybrid Composites ◽  
Phenol Formaldehyde ◽  
Natural Fibre ◽  
The Other ◽  
Fibre Reinforcement ◽  
Dry Conditions

AbstractThis investigation is carried out to understand the effects of water absorption on the mechanical properties of hybrid phenol formaldehyde (PF) composite fabricated with Areca Fine Fibres (AFFs) and Calotropis Gigantea Fibre (CGF). Hybrid CGF/AFF/PF composites were manufactured using the hand layup technique at varying weight percentages of fibre reinforcement (25, 35 and 45%). Hybrid composite having 35 wt.% showed better mechanical properties (tensile strength ca. 59 MPa, flexural strength ca. 73 MPa and impact strength 1.43 kJ/m2) under wet and dry conditions as compared to the other hybrid composites. In general, the inclusion of the fibres enhanced the mechanical properties of neat PF. Increase in the fibre content increased the water absorption, however, after 120 h of immersion, all the composites attained an equilibrium state.

scholarly journals Enzymes for Leather Processing: Effect on Pickling and Chroming

Materials ◽  
2021 ◽  
Vol 14 (6) ◽  
pp. 1480
Author(s):  
Renata Biškauskaitė ◽  
Violeta Valeikienė ◽  
Virgilijus Valeika
Keyword(s):  
Mechanical Properties ◽  
Acidic Medium ◽  
Proteolytic Enzymes ◽  
Relative Elongation ◽  
The Other ◽  
Shrinkage Temperature ◽  
Processing Effect ◽  
Leather Processing ◽  
Production Processes ◽  
Pickling Process

Recently, increasing attention has been paid to the application of enzymes in a wide variety of leather production processes. The aim of the present study was to investigate the action of enzymatic pickling on derma’s collagen and the influence of this action on subsequent processes and properties of chromed and finished leather. The application of active in acidic medium proteolytic enzymes in the pickling process led to an additional impact on derma structure: collagen was more strongly affected and the porosity of the pelt dermis was reduced, but the hide became more thermally stable. The enzymatically pickled pelt bonded more chromium and reached higher shrinkage temperature while chroming; dyes penetrated deeper; such leather bonded more fatliquors. On the other hand, the action of enzymes worsened the physical–mechanical properties of the leather, as the experimental leather was weaker than the conventional one. The first was characterised by weaker grain layer and had significantly higher relative elongation. Therefore, as some properties improve and others worsen during such a process, the application of every enzyme should be carefully investigated and optimized to produce a leather with defined properties.

Relationship of Microstructure and Mechanical Properties in Er-Containing Aluminum Alloy

2015 ◽  
Vol 1120-1121 ◽  
pp. 1109-1114
Author(s):  
Xin Lei ◽  
Hui Huang ◽  
S.P. Wen
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Aluminum Alloy ◽  
Treatment Process ◽  
Mg Alloys ◽  
The Other ◽  
Heat Treatment Process ◽  
Comprehensive Performance ◽  
Relationship Of ◽  
Al Mg Alloys

This study investigated the mechanical properties and microstructures of Er-containing Al–Mg alloys. The research found that the H114-T sheet of Er-containing Al–Mg alloys showed a relative good comprehensive performance in mechanical properties. With the special rolling and heat treatment process, this H114-T sheet showed different morphology of microstructures with the other sheets in Er-containing Al–Mg alloys. Grains in H114-T sheet performed irregular shape polygon, a number of subgrains appeared in grains, the amount of dislocations in grains decreased. H114-T sheet possessed a lot of Copper texture, this may be one of important factors influenced the mechanical properties.

scholarly journals EFFECT OF THERMO-MECHANICAL TREATMENT ON PROPERTIES OF PARICA PLYWOODS (Schizolobium amazonicum Huber ex Ducke)

2017 ◽  
Vol 41 (1) ◽  
Author(s):  
Mírian de Almeida Costa ◽  
Cláudio Henrique Soares Del Menezzi
Keyword(s):  
Mechanical Properties ◽  
Mechanical Treatment ◽  
Physical And Mechanical Properties ◽  
The Other ◽  
Modulus Of Rupture ◽  
Thermal Treatments ◽  
Mechanical Compression ◽  
Specific Mass ◽  
Thermo Mechanical Treatment ◽  
Temperature And Pressure

ABSTRACT Thermo-mechanical treatment is a technique for wood modification in which samples are densified by means of heat and mechanical compression, applied perpendicularly to fibers, which under different combinations of time, temperature, and pressure increases wood density and thus improve some of its properties. This study aimed to treat thermo-mechanically parica plywood and observe the effects on its physical and mechanical properties. Specimens were submitted to two treatments, 120 and 150 ºC, remaining under pressure for seven minutes and, subsequently, under zero pressure for 15 minutes. Results showed a significant increase in specific mass from 0.48 g cm-3 to an average of 0.56 g cm-3, and a compression ratio of about 31.7% on average. Physical properties also varied significantly and results showed that treated samples swelled and absorbed more water than those untreated, leading to a greater thickness non-return rate. This indicates the proposed thermal treatments did not release the internal compressive stress generated during panel pressing, not improving its dimensional stability as a result. On the other hand, mechanical properties were positively affected, leading to an increase of 27.5% and 51.8% in modulus of rupture after treatments at 120 and 150 ºC, respectively. Modulus of elasticity and glue-line shear strength did not vary statistically and Janka hardness was 29.7% higher after treatment at 150 ºC.

scholarly journals Efficient interfacial interaction for improving mechanical properties of polydimethylsiloxane nanocomposites filled with low content of graphene oxide nanoribbons

RSC Advances ◽  
2017 ◽  
Vol 7 (36) ◽  
pp. 22045-22053 ◽  
Author(s):  
Neng-Jian Huang ◽  
Jing Zang ◽  
Guo-Dong Zhang ◽  
Li-Zhi Guan ◽  
Shi-Neng Li ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Graphene Oxide ◽  
Filler Content ◽  
Interfacial Interaction ◽  
Solvent Free ◽  
The Other ◽  
Graphene Oxide Nanoribbons ◽  
Free Process ◽  
Reinforcement Efficiency

GONR-filled H-t-PDMS nanocomposites were fabricated by using a facile solvent-free process, and the reinforcement efficiency of GONRs at low filler content is superior to those of the other carbon nano-fillers.

Sign in / Sign up

Export Citation Format

Share Document