scholarly journals Effects of Shoot Size and Genotype on Energy Properties of Poplar Biomass in Short Rotation Crops

Energies ◽  
2019 ◽  
Vol 12 (11) ◽  
pp. 2051 ◽  
Author(s):  
Cristina Eimil-Fraga ◽  
Xurxo Proupín-Castiñeiras ◽  
Jose Antonio Rodríguez-Añón ◽  
Roque Rodríguez-Soalleiro
Keyword(s):  
Moisture Content ◽  
Acid Soil ◽  
Basic Density ◽  
Calorific Value ◽  
Volatile Matter ◽  
Thermochemical Conversion ◽  
Basal Diameter ◽  
Short Rotation ◽  
Shoot Size ◽  
Rotation Crops

Eight poplar genotypes grown in a short rotation forest plantation established in an acid soil in South Europe were sampled at the age of 7 years to determine the energy properties regarding thermochemical conversion. The goal was to address the effect of selection of genotypes or shoot size at harvest on the energy quality of biomass. Between 34 and 50 biomass samples were obtained for each genotype: three disks were systematically sampled along the stem and were pooled together with a subsample of leafless branches representative of the biomass share of this component. Several energy properties were determined: higher calorific value, net calorific value, fresh moisture content, basic density, ash, volatile matter, fixed carbon content and elemental composition. Genotype had a significant effect on most of these properties, and the balsam genotypes displayed superior quality parameters and also higher biomass yield than the Euramerican genotypes. As a covariate, shoot basal diameter had a significant effect on the moisture content, basic density, ash content and on the concentrations of the elements N, K, Ca, Mg, S, Na and C. It was concluded that genotypes with low nutrient requirements planted at low density (<8000 cuttings ha−1) and harvested at a long enough rotation (7 years) produce good yields and high chip quality. Poplar short rotation crops can be grown to produce chips of A2 quality for non-industrial heating use (according to UNE-EN ISO 17225-4), able to be combusted in domestic thermal facilities of <1 MWth power.

scholarly journals USE OF THE INAJÁ STIPE (Attalea maripa (AUBL.) MART.) FOR THE GENERATION OF BIOENERGY

2019 ◽  
Vol 8 (3) ◽  
Author(s):  
Thais Yuri Rodrigues Nagaishi ◽  
Sueo Numazawa ◽  
Marcio Da Silva Cruz Freitas Nagaishi ◽  
Camila Thiemy Dias Numazawa ◽  
Paulo Renato Souza De Oliveira ◽  
...  
Keyword(s):  
Moisture Content ◽  
Basic Density ◽  
Calorific Value ◽  
Volatile Matter ◽  
Palm Tree ◽  
Physical Analysis ◽  
Drying Process ◽  
Stipe Length ◽  
Energetic Analysis ◽  
Bioclimatic Conditions

The objective of this study was to evaluate the bioenergetics aptitude of Inaja stipe. The samples were collected in five sites in the northeast of Pará State: Cametá, Abaetetuba, São João de Pirabas, São Caetano de Odivelas and Capitão Poço. In each area, 25 matrices were identified and evaluated. The breast circumference (CAP) and the stipe length (AE) were collected for physical, chemical and energetic analysis, and a composite sample was collected from three random stipes from each zone. The analyzes were in accordance with the recommended Brazilian standards: ABNT 11940 (1983) for the physical analysis, ABNT 8112 (1986) for chemical analysis, and ABNT 8633 (1983) for energetic analysis. Regarding CAP, an average of 132.43 cm was obtained (CV = 27.81%), and AE had an average of 314.89 cm (CV = 30.67%). These variations may be explained by the different bioclimatic conditions in each region where the populations are located, as well as the different ages of each palm tree. The average values of the physical variables, moisture content and basic density were 50.09% and 0.34 g.cm-³, respectively. Therefore, it is recommended to perform a drying process, and it may be outdoors for the equilibrium moisture content with the region. The chemical tests indicated an average volatile matter of 82.46%, with an ash content of 0.83% and a fixed carbon of 16.76%. The higher calorific value was, on average, 4586.25 kcal.kg-1. The results indicate that Inaja stipe can be suitable for energetic uses, such as heat generation.

scholarly journals Characteristics of Woody Cutting Waste Briquette with Paper Waste Pulp as Binder

2020 ◽  
Vol 190 ◽  
pp. 00030
Author(s):  
Qurrotin Ayunina Maulida Okta Arifianti ◽  
Azmi Alvian Gabriel ◽  
Syarif Hidayatulloh ◽  
Kuntum Khoiro Ummatin
Keyword(s):  
Moisture Content ◽  
Ignition Time ◽  
Combustion Process ◽  
Calorific Value ◽  
Volatile Matter ◽  
Proximate Analysis ◽  
Hydraulic Press ◽  
Combustion Characteristic ◽  
Paper Waste ◽  
Iron Mold

The current research aimed to increase the calorific value of woody cutting waste briquette with paper waste pulp as binder. There were three different binder variation used in this study, they are 5 %, 10 %, and 15 %. To create a briquette, a cylindrical iron mold with diameter of 3.5 cm and height of 3 cm and a hydraulic press with 2 t power were applied. The physical characteristics of the combination woody waste briquette and paper waste pulp, such as moisture content, ash content, volatile matter and carbon fix were examined using proximate analysis. The calorific value of briquetted fuel was tested by bomb calorimeter. The combustion test was performed to determine the combustion characteristic of briquettes, for example initial ignition time, temperature distribution, and combustion process duration. The general result shows that the calorific value of briquette stood in the range of 4 876 kCal kg–1 to 4 993 kCal kg–1. The maximum moisture content of briquette was 5.32 %. The longest burning time was 105 min.

scholarly journals Analysis of the Quality of Mixed Coconut Shell Waste Briquettes with Various Biomass Additives as Alternative Fuels

2021 ◽  
Vol 4 (2) ◽  
Author(s):  
Yusraida Khairani Dalimunthe ◽  
Sugiatmo Kasmungin ◽  
Listiana Satiawati ◽  
Thariq Madani ◽  
Teuku Ananda Rizky
Keyword(s):  
Moisture Content ◽  
Calorific Value ◽  
Volatile Matter ◽  
Matter Content ◽  
Ash Content ◽  
Coconut Shell ◽  
Bamboo Charcoal ◽  
A Value ◽  
Shell Waste

The purpose of this study was to see the best quality of briquettes from the main ingredient of coconut shell waste<br />with various biomass additives to see the calorific value, moisture content, ash content, and volatile matter<br />content of the biomass mixture. Furthermore, further research will be carried out specifically to see the quality of<br />briquettes from a mixture of coconut shell waste and sawdust. The method used in this research is to conduct a<br />literature study of various literature related to briquettes from coconut shell waste mixed with various additives<br />specifically and then look at the best quality briquettes produced from these various pieces of literature. As for<br />what is determined as the control variable of this study is coconut shell waste and as an independent variable,<br />namely coffee skin waste, rice husks, water hyacinth, Bintaro fruit, segon wood sawdust, coconut husk, durian<br />skin, bamboo charcoal, areca nut skin, and leather waste. sago with a certain composition. Furthermore, this<br />paper also describes the stages of making briquettes from coconut shell waste and sawdust for further testing of<br />the calorific value, moisture content, ash content, volatile matter content on a laboratory scale for further<br />research. From various literatures, it was found that the highest calorific value was obtained from a mixture of<br />coconut shell waste and bamboo charcoal with a value of 7110.7288 cal / gr and the lowest calorific value was<br />obtained from a mixture of coconut shell waste and sago shell waste with a value of 114 cal / gr, then for the value<br />The highest water content was obtained from a mixture of coconut shell waste and rice husk with a value of<br />37.70% and the lowest water content value was obtained from a mixture of coconut shell waste 3.80%, then for the<br />highest ash content value was obtained from a mixture of coconut shell waste and coffee skin with a value of<br />20.862% and for the lowest ash content value obtained from a mixture of coconut shell and Bintaro fruit waste,<br />namely 2%, and for the highest volatile matter content value obtained from a mixture of coconut shell and coconut<br />husk waste with a value of 33.45% and for the value of volatile matter levels The lowest was obtained from a<br />mixture of coconut shell waste and sago skin waste with a value of 33 , 45%.

scholarly journals GROWTH AND ENERGY QUALITY OF EUCALYPTUS WOOD IN DIFFERENT CROP-LIVESTOCK-FOREST SPATIAL ARRANGEMENTS

FLORESTA ◽  
2020 ◽  
Vol 50 (4) ◽  
pp. 1707
Author(s):  
Helio Tonini ◽  
Marina Moura Morales ◽  
Flavio Jesus Wruck ◽  
Ronaldo Maran Deliberali
Keyword(s):  
Genetic Material ◽  
Volume Growth ◽  
Basic Density ◽  
Calorific Value ◽  
Volatile Matter ◽  
Ash Content ◽  
High Yield ◽  
Fixed Carbon ◽  
Cropland Area ◽  
Eucalyptus Wood

The aim of the present study was to assess the growth and energetic properties of genetic material of eucalyptus grown in several integrated crop-livestock system spatial arrangements in Barra-do-Garças City (MT). The genetic material of 76-month old Eucalyptus spp from eight spatial arrangements were assessed according to the following properties: diameter, height and volume growth, mortality rate, dry matter yield, sapwood to heartwood ratio, form factor, bark volume, basic density, superior calorific value, ash content, volatile matter, fixed carbon and trunk energy. Data analysis was performed by adjusting growth function, test for model identity and parameters equality and ANOVA tests to Scott-Knott’s mean clustering test. Eucalyptus grandis x E. urophylla clones from recorded the highest energy efficiency due to their high yield volume, which was decisive to determine estimated energy available per tree and cropland area. Growth, stem shape and basic density varied among, and within, the same genetic materials, depending on their respective spatial arrangement. However, solid biomass properties (high calorific value, ash content, fixed carbon and volatile matter) remained stable.

scholarly journals PENGARUH SUHU DAN WAKTU KARBONISASI TERHADAP NILAI KALOR DAN KARAKTERISTIK PADA PEMBUATAN BIOARANG BERBAHAN BAKU PELEPAH AREN (Arenga pinnata)

2015 ◽  
Vol 4 (2) ◽  
pp. 46-52
Author(s):  
Erwin Junary ◽  
Julham Prasetya Pane ◽  
Netti Herlina
Keyword(s):  
Moisture Content ◽  
Carbon Content ◽  
Calorific Value ◽  
Volatile Matter ◽  
Matter Content ◽  
Ash Content ◽  
Alternative Source ◽  
Renewable Biomass ◽  
Volatile Matter Content ◽  
Temperature Variable

The availability of the petroleum fuels that deprived from fossil is depleted with the increase of human population. The challenge for this fuel shortage crisis can certainly be anticipated with the manufacture of fuels deprived from renewable biomass. The study of this research is to create a biocharcoal deprived from sugar palm (Arenga pinnata) with the optimum carbonization time and temperature in order to obtain a biocharcoal with the highest calorific value. Biocharcoal is a charcoal created from biomass. The study of the determination of the optimum conditions for the manufacture of biocharcoal from sugar palm (Arenga pinnata) has a temperature variable of 300, 350, 400, 450 and 500 0C and time variable of 60, 90 and 120 minutes. Sugar palm was first cut into a small pieces and dried up under the sun and then put into a furnace to carbonate it according to the predetermined variables. The product from furnace was then put inside a desicator to cool it off for 30 minutes and then analyze it with moisture content test, ash content test, volatile matter content test, carbon content test and calorific value test. The best result was obtained at the temperature of 350 0C and 120 minutes of carbonization with the calorific value of 8611,2581 cal/gr, moisture content of %, ash content of %, volatile matter content of % and carbon content of %. Based of the calorific value obtained, the result shows that sugar palm (Arenga pinnata) biocharcoal could be utilize as an renewable alternative source fuels

scholarly journals Effect Of Water Content On Characteristics Fuel From The Municipal Solid Waste Through The Pyrolysis Process

2021 ◽  
Vol 5 (2) ◽  
pp. 9-16
Author(s):  
Imron Rosyadi ◽  
Ni Ketut Caturwati ◽  
Ahmad Fauzi
Keyword(s):  
Moisture Content ◽  
Municipal Solid Waste ◽  
Solid Waste ◽  
Water Content ◽  
Biomass Conversion ◽  
Calorific Value ◽  
Treatment Method ◽  
Volatile Matter ◽  
Average Error ◽  
Rice Samples

The increase in the population of Indonesia is proportional to the increase in the amount of waste produced. Municipal solid waste (MSW) especially organic waste, can be used as solid fuel by means of the torefaction process. Torefaction is a thermo-chemical heat treatment method for biomass conversion that takes place at a temperature of 200oC to 300oC under conditions of atmospheric pressure and in the absence of oxygen. The purpose of this study was to determine the effect of moisture content on calorific, proximate and ultimate values ​​of torefaction samples using municipal solid waste. Setting the water content in the mixed sample (30% rice + 70% wood) with variations in moisture content of 30%, 40%, and 50%; and rice and wood samples with variations in moisture content of 40% and 50%. The torefaction was carried out at a temperature of 300oC for one hour and  inert gas  N2. Torefaction products have been tested contain of the calorific value, proximate testing, and ultimate testing. The results obtained were the best calorific value in the rice sample, the moisture content of 40% was 6351.1 cal / g or equivalent to sub-bituminous coal. The proximate and ultimate results of the best heating value are rice samples with 40% moisture content, fixed carbon 62.95%, volatile matter 27.85%, moisture 7.06%, ash 2.14%, carbon 71.85%, hydrogen. 2.80%, nitrogen 3.17%, and sulfur 0.05%. The calorific value calculation method that is almost close to the test results is the Dulong method, with an average error percentage of 1.63%.

scholarly journals THE EFFECT OF BINDER RATIO ON THE PHYSICAL AND COMBUSTION CHARACTERISTICS OF CARBONIZED RICE STALK BRIQUETTES

2020 ◽  
pp. 221-229
Author(s):  
Rapheal Ige ◽  
Elinge Ogala ◽  
Cosmos Moki ◽  
Abdulrahman Habeeb
Keyword(s):  
Moisture Content ◽  
Carbon Content ◽  
Calorific Value ◽  
Volatile Matter ◽  
Ash Content ◽  
Hot Water ◽  
High Concentration ◽  
Fixed Carbon ◽  
Binder Ratio ◽  
Fixed Carbon Content

The selection or choice of agro-waste briquettes for domestic and industrial cottage applications depends on the fuel properties. In this study, the briquette was produced by carbonizing the rice stalk followed by crushing and sieving, the binder was prepared by dissolving the starch in hot water, then mixed with the sieved carbonized rice stalk and then the briquette was produced using the briquetting machine. Proximate analyses, viability, characteristics and combustion were determined to know the average composition of their constituents. From the results obtained it was observed that ash content, moisture content, after glow and ignition propagation decrease as the binder ratio increase while fixed carbon content, volatile matter, calorific value, density and compressive strength increase. The results of this work indicate that briquettes produced using high concentration of the binder would make good biomass fuels. However, it has a high moisture content of 25.00%, high ash content of 23.00%, moderate volatile matter of 44.80%, low fixed carbon content of 32.20%, moderate calorific value of 13.86 MJ/Kg and high density of 0.643g/cm3. The results obtained for all the parameters showed that rice stalks briquettes produced with high concentration of the binder (starch) had a better performance based on their combustion profile.

Thermogravimetric Analysis of the Fuel Properties of Empty Fruit Bunch Briquettes

2014 ◽  
Vol 67 (3) ◽  
Author(s):  
Bemgba Bevan Nyakuma ◽  
Anwar Johari ◽  
Arshad Ahmad ◽  
Tuan Amran Tuan Abdullah
Keyword(s):  
Thermal Decomposition ◽  
Thermogravimetric Analysis ◽  
Moisture Content ◽  
Volatile Matter ◽  
Proximate Analysis ◽  
Matter Content ◽  
Thermochemical Conversion ◽  
Uniform Structure ◽  
Thermochemical Properties ◽  
Empty Fruit Bunch

The thermochemical properties of biomass are largely influenced by the nature, yield and composition of the feedstock. In addition, the low moisture content, energy density and solid uniform structure of briquettes have been reported to improve heat and mass transfer during thermochemical conversion. Hence, this study is aimed at investigating the thermochemical properties of Empty Fruit Bunch (EFB) briquettes using Thermogravimetric analysis (TGA). The heating value (HHV), ultimate and proximate analysis was determined using standard ASTM techniques. Consequently, the thermal decomposition behavior of the fuel was determined by heating the sample from 50°C to 900°C in a thermogravimetric analyzer (TGA) at 10°C per min heating rate. The ultimate and proximate analysis revealed that EFB briquette contains low moisture content, ash content and high fixed carbon, volatile matter content while the HHV was 17.57 MJ/kg. In addition, TGA results indicated thermal decomposition of the fuel occurs in four stages. Devolatization commenced at 206°C with a peak devolatization temperature (Tmax) of 325°C resulting in 70% weight loss.

scholarly journals The Characteristics of Bamboo Charcoal Derived from Bambusa vulgaris Schrad and Arundinaria gigantea (Walter) Muhl Growing in Different Types of Habitats

2018 ◽  
Vol 10 (1) ◽  
pp. 1-10
Author(s):  
Ratri Yuli Lestari, M.Env. ◽  
Dwi Harsono ◽  
Nazarni Rahmi
Keyword(s):  
Moisture Content ◽  
Calorific Value ◽  
Volatile Matter ◽  
Ash Content ◽  
Bamboo Charcoal ◽  
Fixed Carbon ◽  
Arundinaria Gigantea ◽  
Bambusa Vulgaris ◽  
Different Types ◽  
Different Altitudes

Altitude is one of the factors that affect the growth of bamboo. Bamboo species used in this study was Bambusa vulgaris and Arundinaria gigantea. The objectives of this study are to investigate the effect of altitude to the characteristics of bamboo charcoal harvested from three different altitudes (Lumpangi, Banjarbaru/Martapura, Marabahan). Parameters tested in this study were moisture content, ash content, volatile matter, fixed carbon and calorific value. The result showed that altitute significantly affected the characteristics of bamboo charcoal. Bamboo charcoal from Banjarbaru/Martapura had the best characteristics than the charcoal produced from other locations. The moisture content, ash content, volatile matter, fixed carbon and calorific value of B. vulgaris were 0.77 %; 3.49 %; 8.63 %; 87.11 % and 7,331.05 kal/g. The moisture content, ash content, volatile matter, fixed carbon and calorific value of A. gigantea were 0.19 %; 12.46 %; 4.48 %; 87.11 % and 6,640.69 kal/g, respectively.

scholarly journals Hasil Pengujian Proksimasi Dan Gas Buang Pada Briket Campuran Limbah Serutan Kayu, Sekam Padi Dan Bulu Ayam

2021 ◽  
Vol 14 (1) ◽  
pp. 33-39
Author(s):  
Muhamad Rizky Adipratama ◽  
Reza Setiawan ◽  
Najmudin Fauji
Keyword(s):  
Moisture Content ◽  
Rice Husk ◽  
Alternative Energy ◽  
Fossil Fuels ◽  
Calorific Value ◽  
Volatile Matter ◽  
Ash Content ◽  
Biomass Energy ◽  
Fixed Carbon ◽  
Wood Shavings

Biomass energy is one that can be used as an alternative energy as a substitute for fossil fuels and can also be useful for reducing environmental pollution due to increasing waste or waste. The manufacture of briquettes from chicken feather waste, wood shavings and rice husk waste aims to help deal with the problem of waste and use it as an alternative fuel. The making of briquettes is carried out by the process of drying the ingredients, charcoal, milling, sieving, kneading, printing, drying, proximate testing and measuring emissions on the briquettes. In this study, the composition of a mixture of chicken feathers (30%, 40%, 50%), wood shavings and rice husk (35%, 30%, 25%) was treated as well as particle sizes of 30 mesh and 60 mesh. The results of this study indicate that the lowest moisture content is in sample B2 of 4.5%. The lowest levels of volatile matters were in sample A1 of 37.4%. The lowest ash content was found in sample B3 at 10.8%. The highest fixed carbon was found in sample A3 at 45.1%. The highest calorific value (Gross Calorific Value) is found in the B3 sample of 5594 Kcal / Kg. And it has the highest CO, CO2, and HC emissions produced from the briquettes, namely 0.24%, 0.8%, 46 ppm. The properties of briquettes that have met SNI standards are moisture content, calorific value (except for sample A1), and the resulting emissions. And those that have not met SNI standards are the levels of volatile matter, ash content and fixed carbon. The resulting briquette can be used because the calorific value obtained is quiet high, which is above the specified standard of ≥ 5000 Kcal/Kg.

Sign in / Sign up

Export Citation Format

Share Document