scholarly journals Applying Cassava Stems Biochar Produced from Agronomical Waste to Enhance the Yield and Productivity of Maize in Unfertile Soil

Fermentation ◽  
2021 ◽  
Vol 7 (4) ◽  
pp. 277
Author(s):  
Saowanee Wijitkosum ◽  
Thavivongse Sriburi
Keyword(s):  
Pore Diameter ◽  
Total Pore Volume ◽  
Maize Yield ◽  
Low Fertility ◽  
Stable Carbon ◽  
Untreated Soil ◽  
Average Pore ◽  
Nutrient Contents ◽  
Maize Cultivation ◽  
Cassava Stem

Many agronomical wastes are produced annually in significant amounts after cultivation, especially in agricultural countries. This study applied biochar produced from the pyrolysis of cassava stems to improve soil with low fertility for maize cultivation. The effect of soil biochar incorporation on maize yield and productivity was also investigated. Eight experimental plots, each with four replicates, were applied with cassava stem biochar (CSB) at different rates of 0.5 kg/m2 (TB0.5), 2.5 kg/m2 (TB2.5) and 3.0 kg/m2 (TB3.0), fertilizer at 0.56 kg/m2 (TM), fertilizer at 0.56 kg/m2 mixed with CSB at 0.5 kg/m2 (TMB0.5), 2.5 kg/m2 (TMB2.5), 3.0 kg/m2 (TMB3.0) and untreated soil (TC). Pyrolysis of cassava stems at 450–500 °C produced strongly alkaline CSB with pH 9.6 and increased nutrient contents. Specific surface area and total pore volume increased, and pores were classified as mesoporous, while average pore diameter decreased. CSB had a highly stable carbon content of 58.46%, with high aromaticity and polarity obtained from O/C and H/C ratios. Results indicated that CSB enhanced and supported maize growth by improving soil physicochemical properties to suit cultivation. Applying CSB into the soil gave higher maize yield and productivity than cultivation using fertilizer. The highest yield and nutrition contents were obtained in seed from cultivation using fertilizer mixed with biochar at 3.0 kg/m2. Biochar production from cassava stems generated a useful commodity from waste material.

scholarly journals Microstructure Analysis of Synthesized LiBOB

2015 ◽  
Vol 15 (3) ◽  
pp. 242-247 ◽  
Author(s):  
Etty Marti Wigayati ◽  
Christin Rina Ratri ◽  
Ibrahim Purawiardi ◽  
Fadli Rohman ◽  
Titik Lestariningsih
Keyword(s):  
Crystal Structure ◽  
Surface Area ◽  
Pore Diameter ◽  
Active Material ◽  
Total Pore Volume ◽  
Particle Morphology ◽  
Average Pore ◽  
Round Shape ◽  
Ft Ir ◽  
Battery Application

Lithium bis (oxalate) borate or LiBOB is an active material used as the electrolyte for lithium battery application. LiBOB (LiB(C2O4)2) powder was prepared from LiOH, H2C2O4 and H3BO3. The employed method was solid state reaction. LiBOB powder produced from the reaction was then observed using SEM and TEM. Surface area was analyzed using Quantachrome Nova 4200e. From the analysis analyzed using XRD to identify the resulting phases, crystal structure, and crystallite size. The functional groups were analyzed using FT-IR. The particle morphology was result, it was seen that the resulted phases were C4LiBO8 and LiB(C2O4)2.H2O, the crystal structure was orthorhombic with space group Pbca and Pnma. From the particle morphology observation it was shown that micro pores were created irregularly. When the observation was deepened, nanopores with elongated round shape were seen within the micropores. The pore size was approximately 50–100 nm. The surface area, total pore volume, and average pore diameter of LiBOB powder was 88.556 m2/g, 0.4252 cm3/g, and 19.2 nm respectively.

Experimental Research on the Preparation of Porous Activated Carbon from Orange Wastes

2009 ◽  
Vol 79-82 ◽  
pp. 1907-1910
Author(s):  
Zhi Gang Xie
Keyword(s):  
Activated Carbon ◽  
Surface Area ◽  
Pore Volume ◽  
Pore Diameter ◽  
Total Pore Volume ◽  
Carbonization Temperature ◽  
Bet Surface Area ◽  
Average Pore ◽  
Impregnation Ratio ◽  
Heat Preservation

Porous activated carbon was prepared from orange wastes using zinc chloride as an activating agent by one-step carbonization method. Effects of impregnation ratio, carbonization temperature and heat preservation time on pore characteristics of activated carbon were studied. The porous structures of the orange wastes activated carbon were investigated by BET, D-R equations, BJH equations and Kelvin theory. The morphology was observed using transmission electron microscopy (TEM). The mesoporous activated carbon is gained when the impregnation ratio is 3:1; the carbonization temperature is 550°Cand heat preservation time is 1.0 h. The activated carbon has total pore volume 2.098 cm3/g, mesoporous pore volume 1.438 cm3/g, with a high BET surface area 1476m2/g. The pore distribution of the mesoporous activated carbon is very concentrative, with average pore diameter of 3.88nm. While, the high specific surface area activated carbon is gained when the impregnation ratio is 2:1; the carbonization temperature is 550°Cand heat preservation time is 1.0 h. The activated carbon has high BET surface area 1909 m2/g, while the total pore volume is only 1.448cm3/g and microporous pore volume is 0.889cm3/g, with average pore diameter of 2.29 nm.

scholarly journals Possibilities of Graphitization of Unburned Carbon from Coal Fly Ash

Minerals ◽  
2021 ◽  
Vol 11 (9) ◽  
pp. 1027
Author(s):  
Zdzisław Adamczyk ◽  
Joanna Komorek ◽  
Barbara Białecka ◽  
Joanna Całus-Moszko ◽  
Agnieszka Klupa
Keyword(s):  
Fly Ash ◽  
Pore Volume ◽  
Pore Diameter ◽  
Coal Fly Ash ◽  
Total Pore Volume ◽  
Starting Material ◽  
Unburned Carbon ◽  
Active Carbons ◽  
Average Pore ◽  
Graphite Phase

The paper presents the characteristics of products annealing at the temperatures of 2400 and 3000 °C of unburned carbon from coal fly ash in terms of its possible use as a starting material in the graphitization process. An amorphous substance (organic substance) with an admixture of some minerals has been found in samples subjected to graphitization. However, the graphite phase is dominant in products subjected to graphitization. Studies have also shown a diverse grain morphology in individual samples. The presence of plate-shaped and tube-shaped grains was found. As the graphitization temperature of the starting material increases (2400 and 3000 °C), the specific surface area in the graphitization products decreases. The total pore volume in the samples after the graphitization process was significantly lower than the pore volume of active carbons produced from other unburned carbon. Average pore diameter is similar to the pore diameter in active carbons. The reflectance value of the matrix for the sample graphitized at 3000 °C is characteristic for graphite. Unburned carbon from Polish fly ash can be used as the starting material for graphitization.

scholarly journals Hydrocracking of Waste Cooking Oil into Biofuel Using Mesoporous Silica from Parangtritis Beach Sand Synthesis by Sonochemistry

2021 ◽  
Author(s):  
Siti Salamah ◽  
Wega Trisunaryanti ◽  
Indriana Kartini ◽  
Suryo Purwono
Keyword(s):  
Mesoporous Silica ◽  
Surface Area ◽  
Pore Diameter ◽  
Liquid Fraction ◽  
Total Pore Volume ◽  
Waste Cooking Oil ◽  
Diesel Oil ◽  
Beach Sand ◽  
Average Pore ◽  
Stainless Steel Reactor

Abstract High content of silica in beach sand can be synthesized into mesoporous silica (MS) using the sonochemistry method with dodecyl-amine (DDA) as a surfactant template. The preparation began by adding sodium silicate dropwise to DDA solution under the rotation speed of 120 rpm. The mixture was then added with H 2 SO 4 and sonicated at 37 Khz at a temperature of 35 ºC for 20 minutes. The product was then filtered, washed, and dried at 50 °C then calcined at 600 ºC for 5 h. After it was calcined, the sample was characterized by using FTIR, Surface Area Analyzer, XRD, SEM, and TEM as well as the acidity using pyridine vapor adsorption. The synthesized MS was then used as a catalyst in hydrocracking waste cooking oil in a semi-batch stainless steel reactor system at 450 ⁰C for 2 h, under 20 ml min -1 H2 flow rate. The hydrocracking product of the liquid fraction was analyzed using GC-MS. The results showed that the best performance of the MS1 was produced by using the DDA concentration of 0.1 M, had optimum acidity at 1.7 mmolg -1 , specific surface area of 233 m 2 g -1 , total pore volume of 0.4cc/g, and average pore diameter of 7.70 nm.The best MS1 catalyst produced liquid fraction with yield of 31.13 wt.% which consisted of 11.10 % diesel oil and 5.04 % gasoline.

scholarly journals Selective Production of Green Hydrocarbons from the Hydrotreatment of Waste Coconut Oil over Ni- and NiMo-supported on Amine-functionalized Mesoporous Silica

2020 ◽  
Vol 15 (2) ◽  
pp. 415-431 ◽  
Author(s):  
Wega Trisunaryanti ◽  
Savitri Larasati ◽  
Triyono Triyono ◽  
Cahyarani Paramesti ◽  
Nugroho Raka Santoso
Keyword(s):  
Electron Microscopy ◽  
Mesoporous Silica ◽  
Pore Volume ◽  
Pore Diameter ◽  
Coconut Oil ◽  
Total Pore Volume ◽  
Average Pore ◽  
Functionalized Mesoporous Silica ◽  
Amine Functionalized ◽  
Green Fuel

In order to overcome the depletion of energy resources, the production of fuel from a renewable source (green fuel) has aroused attention. The present work serves as a comparative study for green fuel production by utilizing monometallic Ni and bimetallic NiMo loaded on amine-functionalized mesoporous silica (MS). Two types of catalysts, denoted as Ni/NH2-MS and NiMo/NH2-MS, were prepared and evaluated for its catalytic activity in the hydrotreatment of waste coconut oil (WCO) at 450 ℃ under the flow of H2 gas (20 mL.min-1). Each catalysts were characterized by using X-ray Diffraction (XRD), Atomic Absorption Spectrometer (AAS), Transmission Electron Microscopy (TEM), Scanning Electron Microscopy (SEM), and Fourier Transform Infra Red (FTIR). Study of selectivity by GC-MS showed that gasoline-range hydrocarbon, especially n-undecane, was the major compound in the liquid products generated by the two amine-functionalized catalysts prepared in this study. The result showed that monometallic Ni/NH2-MS with surface area, total pore volume, nickel loading and average pore diameter 328.68 m2.g-1, 0.25 cm3.g-1, 1.90 wt%, 3.10 nm, respectively, exhibited the best performance in producing liquid hydrocarbon and generated higher level of liquid product (77.9 wt%) than bimetallic NiMo/NH2-MS (76.3 wt%). However, it is highlighted that adding 1.08 wt% of Mo in bimetallic NiMo/NH2-MS comprising 0.83 wt% of Ni improved the catalyst selectivity towards producing higher level of gasoline-range hydrocarbon (43 wt%). The bimetallic NiMo/NH2-MS prepared was found to have surface area, total pore volume, and average pore diameter of 325.13 m2.g-1, 0.14 cm3.g-1, 3.22 nm, respectively. Copyright © 2020 BCREC Group. All rights reserved 

Fuels Desulphurisation by Adsorbtion on Fe / Bentonite

2017 ◽  
Vol 68 (3) ◽  
pp. 483-486
Author(s):  
Constantin Sorin Ion ◽  
Mihaela Bombos ◽  
Gabriel Vasilievici ◽  
Dorin Bombos
Keyword(s):  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
Pore Volume ◽  
Pore Diameter ◽  
Adsorption Process ◽  
Continuous System ◽  
Gas Oil ◽  
Average Pore ◽  
Atmospheric Distillation

Desulfurisation of atmospheric distillation gasoline and gas oil was performed by adsorption process on Fe/ bentonite. The adsorbent was characterized by determining the adsorption isotherms, specific surface area, pore volume and average pore diameter. Adsorption experiments of atmospheric distillation gasoline and gas oil were performed in continuous system at 280�320oC, 5 atm and volume hourly space velocities of 1�2 h-1. The efficiency of adsorption on Fe / bentonite was better at desulphurisation of gasoline versus gas oil.

scholarly journals Photocatalytic activity of Pr-modified TiO2 for the degradation of bisphenol A

2021 ◽  
Vol 3 (2) ◽  
Author(s):  
Denise S. Cordeiro ◽  
Fernando L. Cassio ◽  
Larissa Ciccotti ◽  
Thiago L. R. Hewer ◽  
Paola Corio ◽  
...  
Keyword(s):  
Photocatalytic Activity ◽  
Bisphenol A ◽  
Pore Diameter ◽  
Sol Gel ◽  
Bandgap Energy ◽  
Photocatalytic Efficiency ◽  
Average Pore ◽  
X Ray ◽  
Vis Spectroscopy ◽  
Adsorption Desorption

AbstractPraseodymium doped TiO2 nanoparticles were successfully prepared by the sol–gel method and characterized by X-ray powder diffraction, N2 adsorption–desorption isotherm, and UV–vis spectroscopy. The effects of the dopant on the crystallite size, specific surface area, average pore diameter, pore volume, and bandgap energy were investigated. The photocatalytic activity of the catalysts was evaluated by bisphenol A degradation and mineralization, which is a representative endocrine disruptor. Furthermore, under visible light irradiation the Pr-modified TiO2 photocatalysts exhibited higher photocatalytic efficiency than unmodified TiO2. When praseodymium was loaded (1.0–5.0%) onto the surface of TiO2, the rates of degradation and mineralization were increased 3–5 times.

scholarly journals Preparation of High-Performance Activated Carbon from Coffee Grounds after Extraction of Bio-Oil

Molecules ◽  
2021 ◽  
Vol 26 (2) ◽  
pp. 257
Author(s):  
Jie Ren ◽  
Nanwei Chen ◽  
Li Wan ◽  
Guojian Li ◽  
Tao Chen ◽  
...  
Keyword(s):  
Activated Carbon ◽  
High Performance ◽  
Average Pore Size ◽  
Total Pore Volume ◽  
Micropore Volume ◽  
Bet Surface Area ◽  
Average Pore ◽  
Activation Temperature ◽  
Coffee Grounds ◽  
Bio Oil

In this study, a new method for economical utilization of coffee grounds was developed and tested. The resulting materials were characterized by proximate and elemental analyses, thermogravimetric analysis (TGA), Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), and N2 adsorption–desorption at 77 K. The experimental data show bio-oil yields reaching 42.3%. The optimal activated carbon was obtained under vacuum pyrolysis self-activation at an operating temperature of 450 °C, an activation temperature of 600 °C, an activation time of 30 min, and an impregnation ratio with phosphoric acid of 150 wt.%. Under these conditions, the yield of activated carbon reached 27.4% with a BET surface area of 1420 m2·g−1, an average pore size of 2.1 nm, a total pore volume of 0.747 cm3·g−1, and a t-Plot micropore volume of 0.428 cm3·g−1. In addition, the surface of activated carbon looked relatively rough, containing mesopores and micropores with large amounts of corrosion pits.

scholarly journals Derivation of Luminescent Mesoporous Silicon Nanocrystals from Biomass Rice Husks by Facile Magnesiothermic Reduction

Nanomaterials ◽  
2021 ◽  
Vol 11 (3) ◽  
pp. 613
Author(s):  
Sankar Sekar ◽  
Sejoon Lee
Keyword(s):  
Brown Rice ◽  
Total Pore Volume ◽  
Cost Effective ◽  
High Porosity ◽  
Magnesiothermic Reduction ◽  
Rice Husks ◽  
Average Pore ◽  
Efficient Catalyst ◽  
Mesoporous Silicon ◽  
Si Nanocrystals

High-quality silicon (Si) nanocrystals that simultaneously had superior mesoporous and luminescent characteristics were derived from sticky, red, and brown rice husks via the facile and cost-effective magnesiothermic reduction method. The Si nanocrystals were confirmed to comprise an aggregated morphology with spherical nanocrystals (e.g., average sizes of 15–50 nm). Due to the surface functional groups formed at the nanocrystalline Si surfaces, the Si nanocrystals clearly exhibited multiple luminescence peaks in visible-wavelength regions (i.e., blue, green, and yellow light). Among the synthesized Si nanocrystals, additionally, the brown rice husk (BRH)-derived Si nanocrystals showed to have a strong UV absorption and a high porosity (i.e., large specific surface area: 265.6 m2/g, small average pore diameter: 1.91 nm, and large total pore volume: 0.5389 cm3/g). These are indicative of the excellent optical and textural characteristics of the BRH-derived Si nanocrystals, compared to previously reported biomass-derived Si nanocrystals. The results suggest that the biomass BRH-derived Si nanocrystals hold great potential as an active source material for optoelectronic devices as well as a highly efficient catalyst or photocatalyst for energy conversion devices.

Diffusion of Heavy Oil in SiO2 Model Catalyst and FCC Catalyst

2012 ◽  
Vol 550-553 ◽  
pp. 158-163 ◽  
Author(s):  
Zi Yuan Liu ◽  
Sheng Li Chen ◽  
Peng Dong ◽  
Xiu Jun Ge
Keyword(s):  
Diffusion Coefficient ◽  
Pore Size ◽  
Effective Diffusion Coefficient ◽  
Pore Diameter ◽  
Effective Diffusion ◽  
Model Catalyst ◽  
Average Pore ◽  
Diffusion Factor ◽  
Fcc Catalyst ◽  
Fcc Catalysts

Through the measured effective diffusion coefficients of Dagang vacuum residue supercritical fluid extraction and fractionation (SFEF) fractions in FCC catalysts and SiO2model catalysts, the relation between pore size of catalyst and effective diffusion coefficient was researched and the restricted diffusion factor was calculated. The restricted diffusion factor in FCC catalysts is less than 1 and it is 1~2 times larger in catalyst with polystyrene (PS) template than in conventional FCC catalyst without template, indicating that the diffusion of SFEF fractions in the two FCC catalysts is restricted by the pore. When the average molecular diameter is less than 1.8 nm, the diffusion of SFEF fractions in SiO2model catalyst which average pore diameter larger than 5.6 nm is unrestricted. The diffusion is restricted in the catalyst pores of less than 8 nm for SFEF fractions which diameter more than 1.8 nm. The tortuosity factor of SiO2model catalyst is obtained to be 2.87, within the range of empirical value. The effective diffusion coefficient of the SFEF fractions in SiO2model catalyst is two orders of magnitude larger than that in FCC catalyst with the same average pore diameter. This indicate that besides the ratio of molecular diameter to the pore diameter λ, the effective diffusion coefficient is also closely related to the pore structure of catalyst. Because SiO2model catalyst has uniform pore size, the diffusion coefficient can be precisely correlated with pore size of catalyst, so it is a good model material for catalyst internal diffusion investigation.

Sign in / Sign up

Export Citation Format

Share Document