scholarly journals Wave Frequency Effects on Damage Imaging in Adhesive Joints Using Lamb Waves and RMS

Materials ◽  
2019 ◽  
Vol 12 (11) ◽  
pp. 1842 ◽  
Author(s):  
Erwin Wojtczak ◽  
Magdalena Rucka
Keyword(s):  
Damage Identification ◽  
Lamb Waves ◽  
Excitation Frequency ◽  
Visual Assessment ◽  
Adhesive Joints ◽  
Ultrasonic Waves ◽  
Steel Plates ◽  
Wave Frequency ◽  
Destructive Testing ◽  
Wide Range

Structural adhesive joints have numerous applications in many fields of industry. The gradual deterioration of adhesive material over time causes a possibility of unexpected failure and the need for non-destructive testing of existing joints. The Lamb wave propagation method is one of the most promising techniques for the damage identification of such connections. The aim of this study was experimental and numerical research on the effects of the wave frequency on damage identification in a single-lap adhesive joint of steel plates. The ultrasonic waves were excited at one point of an analyzed specimen and then measured in a certain area of the joint. The recorded wave velocity signals were processed by the way of a root mean square (RMS) calculation, giving the actual position and geometry of defects. In addition to the visual assessment of damage maps, a statistical analysis was conducted. The influence of an excitation frequency value on the obtained visualizations was considered experimentally and numerically in the wide range for a single defect. Supplementary finite element method (FEM) calculations were performed for three additional damage variants. The results revealed some limitations of the proposed method. The main conclusion was that the effectiveness of measurements strongly depends on the chosen wave frequency value.

scholarly journals Detection of debonding in adhesive joints using Lamb wave propagation

2019 ◽  
Vol 262 ◽  
pp. 10012
Author(s):  
Magdalena Rucka ◽  
Erwin Wojtczak ◽  
Jacek Lachowicz
Keyword(s):  
Wave Propagation ◽  
Lamb Waves ◽  
Visual Assessment ◽  
Guided Wave ◽  
Steel Plates ◽  
Experimental Investigations ◽  
Mechanical Degradation ◽  
Adhesively Bonded ◽  
Destructive Testing ◽  
Out Of Plane

Adhesively bonded joints are widely used in many branches of industry. Mechanical degradation of this type of connections does not have significant symptoms that can be noticed during visual assessment, so non-destructive testing becomes a very important issue. The paper deals with experimental investigations of adhesively bonded steel plates with different defects. Five samples (an intact one and four with damages in the form of partial debonding) were prepared. The inspection was conducted with the use of guided wave propagation method. Lamb waves were excited at one point of the sample, whereas the out-of-plane velocity signals were recorded in a number of points spread over the area of overlap. The processing of signals consisted of calculations of weighted root mean square (WRMS). The results of the analysis showed that the WRMS maps allow for identification and determination of size and shape of debonding areas.

Structural Health Monitoring of Thin Aluminum Plate Using Acoustic Sensors

2012 ◽  
Vol 622-623 ◽  
pp. 1389-1395
Author(s):  
R. Nishanth ◽  
K. Lingadurai ◽  
V. Malolan ◽  
Gowrishankar Wuriti ◽  
M.R.M. Babu
Keyword(s):  
Lamb Wave ◽  
Damage Identification ◽  
Lamb Waves ◽  
Time Domain Analysis ◽  
Ultrasonic Waves ◽  
Aluminum Plate ◽  
Identification System ◽  
Time Frequency ◽  
Thin Aluminum ◽  
Aluminum Plates

SHM is defined as “an emerging technology that can be defined as continuous, autonomous, real time, in-service monitoring of the physical condition of a structure by means of embedded or attached sensors with minimum manual intervention” .SHM provides the ability of a system to detect adverse changes within a system’s structure to enhance reliability and reduce maintenance costs. There are different Non-Destructive techniques like acoustic emission, ultrasonic, acousto-ultrasonic, guided ultrasonic waves or Lamb waves which are nowadays investigated for the development of an efficient and user-friendly damage identification system. This paper deals with the latter which is based on Lamb wave propagation. It has been developed especially for distinguishing different kinds of damages. The Lamb wave-based active SHM method uses piezoelectric (PZT) sensors to transmit and receive Lamb waves in a thin Aluminum plate. The Lamb wave modes (AO &SO) travel into the structure and are reflected by the structural boundaries, discontinuities, and damage. By studying their propagation and reflection, the presence of defect in the structure is determined. Laboratory level experiments have been carried out on thin Aluminum plates with angular, horizontal and vertical defect. The obtained waveform is filtered to avoid unwanted noise & disturbances using Savitzky-Golay filtering. The filtered waveforms are compared to differentiate the defects. Short Time Fourier Transform has been carried out on the acquired waveform. This study provides significant insight into the problem of identifying localized damages in the structure using PZT and dispersion of signal after they interact with different types of damage. Those small defects like the horizontal one that may be nearly missed in time domain analysis can also be clearly identified in the STFT analysis. Moreover the occurrence of So mode is also clearly seen. Thus, Lamb waves generated by PZT sensors and time-frequency analysis techniques could be used effectively for damage detection in aluminum plate. This study has given a complete idea of the working and the basic requirements of SHM system.

Ультразвуковой контроль дефектов металлических изделий сложной формы

2021 ◽  
pp. 31-36
Author(s):  
В.В. Ларионов ◽  
А.М. Лидер ◽  
Д.О. Долматов ◽  
Д.А. Седнев
Keyword(s):  
Test Object ◽  
Degrees Of Freedom ◽  
Surface Profile ◽  
Ultrasonic Waves ◽  
Non Destructive Testing ◽  
Destructive Testing ◽  
Six Degrees Of Freedom ◽  
Wide Range ◽  
Manufactured Products ◽  
Non Destructive

Nowadays, automation is an actual issue in the development of methods and equipment for ultrasonic non-destructive testing. The conditions of modern industrial production require the development and application the automated testing equipment which is versatile to a wide range of manufactured products, which can have a complex shape. In this paper, we propose a technique for ultrasonic testing of complex-shaped objects. Such technique implies the application of six degrees of freedom robotic manipulators to ensure the required refraction angle of ultrasonic waves into the test object at each measuring position. The trajectory of the robot movement during scanning is provided by restoring the surface profile of the test object using optical profilometry and determining the location of the test object relative to the robotic manipulator using a probe tip. Within the framework of this work, the effectiveness of the developed technology is verified experimentally.

Time reversibility of Lamb waves in thin plates with surface-bonded piezoelectric transducers is temperature invariant at the best reconstruction frequency

2020 ◽  
pp. 147592172096512
Author(s):  
Bhabagrahi Natha Sharma ◽  
Santosh Kapuria ◽  
A Arockiarajan
Keyword(s):  
Temperature Dependence ◽  
Lamb Wave ◽  
Lamb Waves ◽  
Dominant Role ◽  
Excitation Frequency ◽  
Piezoelectric Transducers ◽  
Time Reversibility ◽  
Adhesive Layers ◽  
Wide Range ◽  
Reconstructed Signal

The Lamb wave time-reversal method has been widely proposed as a baseline-free method for damage detection in thin-walled structures. Under varying thermal environments, it would require that the time reversibility of Lamb waves is temperature invariant. In this study, we examine the temperature dependence of Lamb waves and its time reversibility using experiments and finite element simulations on isotropic plates with surface-bonded piezoelectric wafer transducers for actuation and sensing. The study is conducted at three different temperatures of the system from 25°C to 75°C for a wide range of excitation frequency. The results indicate that the time reversibility can undergo significant changes due to temperature variations depending on the excitation frequency. However, at the best reconstruction frequency corresponding to the maximum similarity of the reconstructed signal with the original input signal (proposed recently as the probing frequency), the change in the percent similarity with temperature is insignificant. The results also demonstrate that changes in the physical properties of both adhesive layers and piezoelectric transducers with temperature play a dominant role in influencing Lamb wave amplitudes. However, only the change in the characteristics of the adhesive layers is responsible for the temperature dependence of the time reversibility of Lamb waves.

Structural Health Monitoring Using PZT Transducer Network and Lamb Waves

2010 ◽  
Author(s):  
J. Q. Mou ◽  
L. Martua ◽  
Y. Q. Yu ◽  
Z. M. He ◽  
C. L. Du ◽  
...  
Keyword(s):  
Health Monitoring ◽  
Lamb Waves ◽  
Numerical Models ◽  
Excitation Frequency ◽  
Ultrasonic Waves ◽  
Short Time Fourier Transform ◽  
Test Plate ◽  
Optimal Excitation ◽  
Short Time ◽  
To Receive

Structure health monitoring (SHM) using ultrasonic waves is an emerging technology that can be applied to real-time detect, locate and quantify the structural damages in aircraft structures. In this paper, the monitoring of crack growth at rivet holes in an aluminum test plate using a PZT transducer network and Lamb waves is investigated. The thin disc PZT transducers surface mounted at the test plate are used as actuators to transmit the windowed sinewave bursts and sensors to receive the ultrasonic Lamb waves. The symmetrical S0 mode and antisymmetrical A0 mode of the Lamb waves in the structures are studied with correlated theoretical, experimental and numerical analysis. The optimal excitation frequency is determined for the test plate. Finite element method (FEM) numerical models for simulations of the wave propagations and interactions with the holes and cracks in the plate are developed and verified with the experimental results. The wave responses modes and characteristics for detection of the cracks at the rivet holes are analyzed. The Lamb wave signals in the PZT transducer network are processed with the short time Fourier transform (STFT). It is demonstrated that the time of flight and the energy transmission ratio of the S0 wave are sensitive to the cracks in the structure.

scholarly journals Non-Invasive Testing of Physical Systems Using Topological Sensitivity

2021 ◽  
Vol 11 (3) ◽  
pp. 1341
Author(s):  
María Higuera ◽  
José M. Perales ◽  
María-Luisa Rapún ◽  
José M. Vega
Keyword(s):  
Lamb Waves ◽  
General Purpose ◽  
Mathematical Tool ◽  
Non Destructive Testing ◽  
Destructive Testing ◽  
Topological Sensitivity ◽  
Physical Systems ◽  
Non Invasive ◽  
Active Infrared Thermography ◽  
Non Destructive

A review of available results on non-destructive testing of physical systems, using the concept of topological sensitivity, is presented. This mathematical tool estimates the sensitivity of a set of measurements in some given sensors, distributed along the system, to defects/flaws that produce a degradation of the system. Such degradation manifests itself on the properties of the system. The good performance of this general purpose post-processing method is reviewed and illustrated in some applications involving non-destructive testing. These applications include structural health monitoring, considering both elastodynamic ultrasonic guided Lamb waves and active infrared thermography. Related methods can also be used in other fields, such as diagnosis/prognosis of engineering devices, which is also considered.

scholarly journals A Novel Ultrasonic TOF Ranging System Using AlN Based PMUTs

Micromachines ◽  
2021 ◽  
Vol 12 (3) ◽  
pp. 284
Author(s):  
Yihsiang Chiu ◽  
Chen Wang ◽  
Dan Gong ◽  
Nan Li ◽  
Shenglin Ma ◽  
...  
Keyword(s):  
Clock Cycle ◽  
High Accuracy ◽  
Ultrasonic Waves ◽  
Oxide Semiconductor ◽  
Average Error ◽  
Cmos Process ◽  
Clock Frequency ◽  
Time Frequency ◽  
Range Finding ◽  
Wide Range

This paper presents a high-accuracy complementary metal oxide semiconductor (CMOS) driven ultrasonic ranging system based on air coupled aluminum nitride (AlN) based piezoelectric micromachined ultrasonic transducers (PMUTs) using time of flight (TOF). The mode shape and the time-frequency characteristics of PMUTs are simulated and analyzed. Two pieces of PMUTs with a frequency of 97 kHz and 96 kHz are applied. One is used to transmit and the other is used to receive ultrasonic waves. The Time to Digital Converter circuit (TDC), correlating the clock frequency with sound velocity, is utilized for range finding via TOF calculated from the system clock cycle. An application specific integrated circuit (ASIC) chip is designed and fabricated on a 0.18 μm CMOS process to acquire data from the PMUT. Compared to state of the art, the developed ranging system features a wide range and high accuracy, which allows to measure the range of 50 cm with an average error of 0.63 mm. AlN based PMUT is a promising candidate for an integrated portable ranging system.

Estimation of the carcass composition of different cattle breeds and crosses from fatness measurements and visual assessments

1986 ◽  
Vol 106 (2) ◽  
pp. 223-237 ◽  
Author(s):  
A. J. Kempster ◽  
J. P. Chadwick ◽  
D. D. Charles
Keyword(s):  
Subcutaneous Fat ◽  
Visual Assessment ◽  
Carcass Composition ◽  
Beef Breed ◽  
Percentage Unit ◽  
Wide Range ◽  
Fat Thickness ◽  
Substantial Bias ◽  
Visual Assessments ◽  
Thickness Measurements

SUMMARYCarcass data for 1053 steers from the Meat and Livestock Commission's beef breed evaluation programme were used to examine the relative precision of alternative fatness assessments for predicting carcass lean percentage. The data were from four trials and comprised both dairy-bred and suckler-bred cattle by a wide range of sire breeds.A visual assessment of carcass subcutaneous fat content to the nearest percentage unit (SFe) was the single most precise predictor both overall (residual S.d. = 2·28) and within breed (residual S.d. = 2·05). Precision was improved by the addition in multiple regression of the percentage perinephric and retroperitoneal fat (KKCF) in carcass, a visual score of the degree of marbling in the m. longissimus and selected fat thickness measurements taken by calipers on cut surfaces (residual S.d. = 2·11 (overall) and 1·90 (within breed)).When the best overall equation was applied to the breed means, there was substantial bias (predicted – actual carcass lean percentage). Biases ranged from +2·5 (purebred Canadian Holstein and Luing) to – 1·3 (Limousin crosses).Breeds differed significantly in carcass lean content when compared at equal levels of fatness measurements. The differences depended both on the precision with which the measurements predicted carcass lean content and the observed differences in carcass composition that existed before adjustments to equal fatness were made.The robustness of prediction equations was examined by applying them to independent sets of data (a total of 334 carcasses) from four other trials involving steers, heifers, cows and young bulls. Equations were stable for cattle of the same breed, sex and similar levels of fatness but important bias was found between more extreme types of cattle.

Energy Harvesting From the Vibrations of Rotating Systems

2017 ◽  
Vol 140 (2) ◽  
Author(s):  
Christopher G. Cooley ◽  
Tan Chai
Keyword(s):  
Rotation Speed ◽  
Excitation Frequency ◽  
Average Power ◽  
Local Maximum ◽  
Operating Conditions ◽  
Centripetal Acceleration ◽  
Local Maxima ◽  
Closed Form Solutions ◽  
Energy Harvesters ◽  
Wide Range

This study investigates the vibration of and power harvested by typical electromagnetic and piezoelectric vibration energy harvesters when applied to vibrating host systems that rotate at constant speed. The governing equations for these electromechanically coupled devices are derived using Newtonian mechanics and Kirchhoff's voltage law. The natural frequency for these devices is speed-dependent due to the centripetal acceleration from their constant rotation. Resonance diagrams are used to identify excitation frequencies and speeds where these energy harvesters have large amplitude vibration and power harvested. Closed-form solutions are derived for the steady-state response and power harvested. These devices have multifrequency dynamic response due to the combined vibration and rotation of the host system. Multiple resonances are possible. The average power harvested over one oscillation cycle is calculated for a wide range of operating conditions. Electromagnetic devices have a local maximum in average harvested power that occurs near a specific excitation frequency and rotation speed. Piezoelectric devices, depending on their mechanical damping, can have two local maxima of average power harvested. Although these maxima are sensitive to small changes in the excitation frequency, they are much less sensitive to small changes in rotation speed.

Sign in / Sign up

Export Citation Format

Share Document