scholarly journals Investigation of Moisture Dissipation of Water-Foamed Asphalt and Its Influence on the Viscosity

Materials ◽  
2020 ◽  
Vol 13 (23) ◽  
pp. 5325
Author(s):  
Ning Li ◽  
Wei Tang ◽  
Xin Yu ◽  
He Zhan ◽  
Hui Ma ◽  
...  
Keyword(s):  
Water Content ◽  
Asphalt Mixture ◽  
Viscosity Reduction ◽  
Residual Water ◽  
Rotational Viscometer ◽  
Force Microscopy ◽  
Foamed Asphalt ◽  
Foaming Process ◽  
Atomic Force ◽  
Afm Analysis

Water-foamed asphalt is capable of improving the workability of asphalt mixture. It has been extensively used for its energy-saving and emission-reducing features. Water plays an essential part in improving the workability of water-foamed asphalt mixture. However, there is still lack in profound studies of moisture dissipation of the water-foamed asphalt over time and its influence on workability. In this study, the evolutions of residual water content and rotational viscosity of the water-foamed asphalt with time were respectively measured by the analytical balance and modified rotational viscometer (RV). The atomic force microscopy (AFM) analysis was conducted to discuss the mechanism of viscosity reduction of water-foamed asphalt. The results showed that moisture evaporation is significantly influenced by the foaming water content and ambient temperature, which results in the different stabilizing time of water-foamed asphalt. When water-foamed asphalt was stabilized, the residual water inside the asphalt was less than 0.01% relative to the asphalt mass. The AFM analysis showed that the foaming process changed the distribution of wax in the water-foamed asphalt resulting in reduction of viscosity. The viscosity reduction of asphalt is highly related to the initial foaming water content. After the foaming process, the viscosity keeps stable and is independent of moisture dissipation.

scholarly journals Back to Nature: Combating Candida albicans Biofilm, Phospholipase and Hemolysin Using Plant Essential Oils

Antibiotics ◽  
2021 ◽  
Vol 10 (1) ◽  
pp. 81
Author(s):  
Ahmed M. El-Baz ◽  
Rasha A. Mosbah ◽  
Reham M. Goda ◽  
Basem Mansour ◽  
Taranum Sultana ◽  
...  
Keyword(s):  
Candida Albicans ◽  
Essential Oils ◽  
Docking Study ◽  
New Drugs ◽  
Molecular Docking Study ◽  
Plant Essential Oils ◽  
Force Microscopy ◽  
Atomic Force ◽  
Afm Analysis ◽  
Phenotypic Methods

Candida albicans is the causative agent of fatal systemic candidiasis. Due to limitations of antifungals, new drugs are needed. The anti-virulence effect of plant essential oils (EOs) was evaluated against clinical C. albicans isolates including cinnamon, clove, jasmine and rosemary oils. Biofilm, phospholipase and hemolysin were assessed phenotypically. EOs were evaluated for their anti-virulence activity using phenotypic methods as well as scanning electron microscopy (SEM) and atomic force microscopy (AFM). Among the C. albicans isolates, biofilm, phospholipase and hemolysins were detected in 40.4, 86.5 and 78.8% of isolates, respectively. Jasmine oil showed the highest anti-biofilm activity followed by cinnamon, clove and rosemary oils. SEM and AFM analysis showed reduced adherence and roughness in the presence of EOs. For phospholipase, rosemary oil was the most inhibitory, followed by jasmine, cinnamon and clove oils, and for hemolysins, cinnamon had the highest inhibition followed by jasmine, rosemary and clove oils. A molecular docking study revealed major EO constituents as promising inhibitors of the Als3 adhesive protein, with the highest binding for eugenol, followed by 1,8-cineole, 2-phenylthiolane and cinnamaldehyde. In conclusion, EOs have a promising inhibitory impact on Candida biofilm, phospholipase and hemolysin production, hence EOs could be used as potential antifungals that impact virulence factors.

Coupling In-Situ Techniques to Analyze Zinc Deposition and Dissolution for Energy Storage Applications

2013 ◽  
Vol 1491 ◽  
Author(s):  
Jayme Keist ◽  
Christine Orme ◽  
Frances Ross ◽  
Dan Steingart ◽  
Paul Wright ◽  
...  
Keyword(s):  
Liquid Electrolyte ◽  
Scattering Data ◽  
Zinc Deposition ◽  
Ionic Liquid Electrolyte ◽  
Force Microscopy ◽  
In Situ Techniques ◽  
X Ray Scattering ◽  
Atomic Force ◽  
Afm Analysis

ABSTRACTThis investigation describes preliminary results of in-situ analysis of zinc deposition within an ionic liquid electrolyte utilizing electrochemical atomic force microscopy (EC AFM). From the AFM analysis, the morphology of the zinc deposition was analyzed by quantifying the surface roughness using height-height correlation functions. These results will be used to analyze the scattering data obtained from zinc deposition analysis utilizing an electrochemical ultra-small angle x-ray scattering (EC USAXS). The goal of this research is to link the early nucleation and growth behavior to the formation of detrimental morphologies.

Self-assembly layer-by-layer fabrication using porphyrin dye anion and polycation

2009 ◽  
Vol 13 (07) ◽  
pp. 774-778 ◽  
Author(s):  
Byung-Soon Kim ◽  
Young-A Son
Keyword(s):  
Ultrathin Films ◽  
Self Assembly ◽  
Film Surface ◽  
Layer By Layer ◽  
Preparation Technique ◽  
Force Microscopy ◽  
Atomic Force ◽  
Diallyldimethylammonium Chloride ◽  
Afm Analysis ◽  
Progressive Growth

In this study, self-assembled alternating film using poly(diallyldimethylammonium chloride) (PDDAC) and meso-tetrakis(4-carboxyphenyl)porphyrin (MTCP) was prepared as a multilayer deposition on glass substrate. This preparation technique for dye deposition may provide new feasibilities to achieve the manufacture of ultrathin films for nanotechnology application. The deposition films were characterized by UV-vis spectrophotometer and Atomic Force Microscopy (AFM) analysis. The results of UV-vis spectra showed that the absorbance characteristic of the multilayer films linearly increased with an increased number of PDDAC and MTCP bilayers. AFM analysis showed the film surface was relatively uniform and the progressive growth of layers was determined.

scholarly journals Study the Effect of Water Content on the Structure of Electrochemically Prepared TiO2 Nanotubes

2022 ◽  
Author(s):  
Sara Al-Waisawy ◽  
Ahmed Kareem Abdullah ◽  
Hadi A. Hamed ◽  
Ali A. Al-bakri
Keyword(s):  
Water Content ◽  
Pure Titanium ◽  
Electrochemical Anodization ◽  
X Ray Diffraction ◽  
Force Microscopy ◽  
Atomic Force ◽  
Titania Nanotube Arrays ◽  
Anodization Process ◽  
Titania Films ◽  
Average Size

In this research, the pure titanium foil was treated in glycerol base electrolyte with 0.7 wt.% NH4F and a small amount of H2O at 17 V for 2 hours by electrochemical anodization process in order to prepare Titania nanotube arrays at room temperature (~25 ºC), different water content was added to the electrolyte as a tube enhancing agent. The high density uniform arrays are prepared by using organized and well aligned these tubes. The average size of tube diameter, ranging from 57 to 92 nm which found it increases with increasing water content, and the length of the tube ranging from 2.76 to 4.12 µm, also found to increase with increasing water content and ranging in size of wall thickness from 23 to 35 nm. A possible growth mechanism is presented. The X-ray diffraction (XRD), atomic force microscopy (AFM), and scanning electron microscopy (SEM) were utilized to study the structure and morphology of the Titania films.

scholarly journals Synthesis of Metarhizium anisopliae–Chitosan Nanoparticles and Their Pathogenicity against Plutella xylostella (Linnaeus)

2021 ◽  
Vol 10 (1) ◽  
pp. 1
Author(s):  
Jianhui Wu ◽  
Cailian Du ◽  
Jieming Zhang ◽  
Bo Yang ◽  
Andrew G. S. Cuthbertson ◽  
...  
Keyword(s):  
Plutella Xylostella ◽  
Metarhizium Anisopliae ◽  
Chitosan Nanoparticles ◽  
Analytical Techniques ◽  
X Ray ◽  
Synthesis Of Nanoparticles ◽  
Force Microscopy ◽  
Atomic Force ◽  
Afm Analysis

Nanotechnology is increasingly being used in areas of pesticide production and pest management. This study reports the isolation and virulence of a new Metarhizium anisopliae isolate SM036, along with the synthesis and characterization of M. anisopliae–chitosan nanoparticles followed by studies on the efficacy of nanoparticles against Plutella xylostella. The newly identified strain proved pathogenic to P. xylostella under laboratory conditions. The characterization of M. anisopliae–chitosan nanoparticles through different analytical techniques showed the successful synthesis of nanoparticles. SEM and HRTEM images confirmed the synthesis of spherical-shaped nanoparticles; X-ray diffractogram showed strong peaks between 2θ values of 16–30°; and atomic force microscopy (AFM) analysis revealed a particle size of 75.83 nm for M. anisopliae–chitosan nanoparticles, respectively. The bioassay studies demonstrated that different concentrations of M. anisopliae–chitosan nanoparticles were highly effective against second instar P. xylostella under laboratory and semi-field conditions. These findings suggest that M. anisopliae–chitosan nanoparticles can potentially be used in biorational P. xylostella management programs.

scholarly journals Synthesis and electrical properties of conductive polyaniline/ SWCNT nanocomposites

2019 ◽  
Vol 15 (34) ◽  
pp. 106-113
Author(s):  
Estabraq T. Abdulla
Keyword(s):  
Electrical Properties ◽  
In Situ Polymerization ◽  
Pure Pani ◽  
Electron Interaction ◽  
Aniline Monomer ◽  
Force Microscopy ◽  
Atomic Force ◽  
Afm Analysis ◽  
Electrical Conductivities ◽  
Walled Carbon Nanotubes

The synthesis of conducting polyaniline (PANI) nanocomposites containing various concentrations of functionalized single-walled carbon nanotubes (f-SWCNT) were synthesized by in situ polymerization of aniline monomer. The morphological and electrical properties of pure PANI and PANI/SWCNT nanocomposites were examined by using Fourier transform- infrared spectroscopy (FTIR), and Atomic Force Microscopy (AFM) respectively. The FTIR shows the aniline monomers were polymerized on the surface of SWCNTs, depending on the -* electron interaction between aniline monomers and SWCNTs. AFM analysis showed increasing in the roughness with increasing SWCNT content. The AC, DC electrical conductivities of pure PANI and PANI/SWCNT nanocomposite have been measured in frequency range (50Hz - 600KHz) and in the temperature range from (30 to 160K). The results show the electrical conductivity of the nanocomposite is higher than pure PANI.

Improved Functional Capabilities of Quasi-Two-Dimensional Tungsten Oxide Nanostructures

2016 ◽  
Vol 689 ◽  
pp. 55-59
Author(s):  
Serge Zhuiykov
Keyword(s):  
Photoelectron Spectroscopy ◽  
Sol Gel ◽  
X Ray Diffraction ◽  
Current Sensing ◽  
X Ray ◽  
Force Microscopy ◽  
Functional Capabilities ◽  
Atomic Force ◽  
Oxide Nanostructures ◽  
Afm Analysis

Electrical properties and morphology of orthorhombic β–WO3 nano-flakes with thickness of ~7-9 nm were investigated at the nanoscale using energy dispersive X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS) and current sensing force spectroscopy atomic force microscopy (CSFS-AFM, or PeakForce TUNATM). CSFS-AFM analysis established good correlation between the topography of the developed nanostructures and various features of WO3 nano-flakes synthesized via a two-step sol-gel-exfoliation method. It was determined that β–WO3 nano-flakes annealed at 550°C possess distinguished and exceptional thickness-dependent properties in comparison with the bulk, micro- and nano-structured WO3 synthesized at alternative temperatures.

Engineered properties of polyurethane laden with beetroot and cerium oxide for cardiac patch application

2021 ◽  
pp. 152808372110542
Author(s):  
Saravana Kumar Jaganathan ◽  
Mohan Prasath Mani ◽  
Ahmad Fauzi bin Ismail ◽  
Ahmad Zahran Mohd Khudzari ◽  
Ahmad Athif Mohd Faudzi
Keyword(s):  
Cerium Oxide ◽  
Infrared Analysis ◽  
Hemolysis Assay ◽  
Force Microscopy ◽  
Patch Application ◽  
Atomic Force ◽  
Coagulation Study ◽  
Afm Analysis ◽  
Hydrophobic Nature ◽  
Cardiac Patch

The cardiac patch provides appropriate physicochemical properties and mechanical strength for the regeneration of damaged heart tissues. In this work, for the first-time, beetroot (BR) is blended with cerium oxide (CeO2) to produce nanofibrous polyurethane (PU) composite patch using electrospinning. The objective of this work is to fabricate the composite and examine its feasibility for cardiac patch applications. Morphological analysis revealed a dramatic reduction of fiber diameter of PU/BR (233 ± 175 nm) and PU/BR/CeO2 (331 ± 176 mm) compared to the pristine PU (994 ± 113 mm). Fourier transform infrared analysis (FTIR) analysis indicated functional peak intensities of the newly formed composite PU/BR and PU/BR/CeO2 were not similar to PU. The addition of beetroot rendered PU/BR hydrophilic (86° ± 2), whereas PU/BR/CeO2exhibited hydrophobic nature (99° ± 3). Atomic force microscopy (AFM) analysis depicted the reduced surface roughness of the PU/BR (312 ± 12 nm) and PU/BR/CeO2 (390 ± 125 nm) than the pristine PU (854 ± 32 nm). The incorporation of beetroot and CeO2 into PU enhanced the tensile strength compared with the pristine PU. The blood clotting time of PU/BR (APTT-204 ± 3 s and PT-103 ± 2 s) and PU/BR/CeO2 (APTT-205 ± 3 s and PT-105 ± 2s) were delayed significantly than the pristine PU(APTT-176 ± 2 s and PT-94 ± 2 s) as revealed in the coagulation study. Further, hemolysis assay showed the less toxic nature of the fabricated composites than the pristine PU. Hence, it can be inferred that the advanced physicochemical and blood compatible properties of electrospun PU/BR and PU/BR/CeO2 nanocomposite can be engineered successfully for cardiac patch applications.

Sign in / Sign up

Export Citation Format

Share Document