scholarly journals Feed Force and Sawdust Geometry in Particleboard Sawing

Materials ◽  
2021 ◽  
Vol 14 (4) ◽  
pp. 945
Author(s):  
Bartosz Pałubicki ◽  
Luďka Hlásková ◽  
Stephan Frömel-Frybort ◽  
Tomasz Rogoziński
Keyword(s):  
Particle Size ◽  
Feed Rate ◽  
Cutting Forces ◽  
Design And Optimization ◽  
Machine Type ◽  
Feed Force ◽  
Circular Sawing ◽  
Cutting Kinematics ◽  
Mechanical Cutting ◽  
Sawing Process

The measurement of cutting forces permits building of physic-mechanical cutting models for a better understanding of the phenomena observed during cutting. It also permits the design and optimization of processes, machines, tools, and wood preparation. Optimization of cutting conditions of wood-based materials can decrease the cutting forces, which directly relates to the energy consumption and surface quality. The sawdust analysis may serve for analysis of cutting kinematics and occupational health risk. The aim of the study was to estimate the correlation between the feed rate and both feed force and sawdust particle size produced during particleboard circular sawing. A saw machine type K700 was used in experiments. There were three feed rates of 12, 18, and 24 m/min executed by a horizontal pneumatic actuator fixed to the sliding side table of the saw machine. Based on the results of the experiments, a positive correlation was observed between the feed rate in a circular sawing process and feed forces and an unexpected particle size distribution depending on the feed rate.

scholarly journals EFFECT OF CUTTING PARAMETERS ON CUTTING FORCES IN TURNING OF CPM 10V STEEL

2021 ◽  
Vol 24 (2) ◽  
pp. 5-8
Author(s):  
Anđelko Aleksić ◽  
◽  
Milenko Sekulić ◽  
Marin Gostimirović ◽  
Dragan Rodić ◽  
...  
Keyword(s):  
Feed Rate ◽  
Cutting Forces ◽  
Cutting Speed ◽  
Physical And Mechanical Properties ◽  
Cutting Parameters ◽  
Radial Force ◽  
Depth Of Cut ◽  
Feed Force ◽  
Cnc Lathe ◽  
Method Analysis

The objective of this paper is to investigate the effect of cutting parameters on cutting forces during turning of CPM 10V steel with coated cutting tool. Machining of CPM 10V steel and finding a suitable tool is very challenging due to its physical and mechanical properties, especially since the machining of this material has not been extensively researched. The experiments were carried out using an Index GU -600 CNC lathe and the cutting forces were measured in process. A three-factorial three-level experimental design was used for the experiments. Statistical method analysis of variance (ANOVA) is applied to study the effects of cutting speed, feed rate, and depth of cut on cutting forces. The results of this study show that depth of cut has the most significant effect on main force and radial force, while feed rate and cutting speed have the most significant effect on feed force. The developed model can be used in the machining industry to predict and analyze cutting parameters for optimal cutting forces.

Influence of the Cutting Speed and Feed Rate on Torque, Feed Force, Roughness and Shape of the Chips During Deep Hole Drilling

2013 ◽  
Vol 10 (2) ◽  
pp. 11-14
Author(s):  
Martin Letavay ◽  
M. Laluha ◽  
Jozef Pilc
Keyword(s):  
Feed Rate ◽  
Cutting Forces ◽  
Cutting Speed ◽  
Hole Drilling ◽  
Deep Hole ◽  
Deep Hole Drilling ◽  
Feed Force ◽  
Gun Drill ◽  
Steel Grades

Abstract This article describes methodology and realization of the deep hole drilling test. Goal of this trial is to define influence of the cutting speed and feed rate on torque and feed force. As well as during the test here was a focus on roughness and shape of the chips. A gun drill was used for deep hole drilling and we used etalon material, were here is possible to define cutting forces without any further testing of different steel grades. Also there is a description of CNC program, which was used for above mentioned testing and it can be utilized during other different trials.

scholarly journals Analysis of Surface Roughness and Cutting Forces in Hard Turning of 42CrMo4 Steel using Taguchi and RSM Method

Mechanika ◽  
2020 ◽  
Vol 26 (3) ◽  
pp. 231-241 ◽  
Author(s):  
Mustafa ÖZDEMİR ◽  
Mehmet Tuncay KAYA ◽  
Hamza Kemal AKYILDIZ
Keyword(s):  
Surface Roughness ◽  
Feed Rate ◽  
Cutting Forces ◽  
Tangential Force ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Radial Force ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
Feed Force

In this study, effects of cutting speed (V), feed rate (f), depth of cut (a) and tool tip radius (R) on  surface roughness (Ra, Rz, and Rt) and cutting forces (radial force (Fx), tangential force (Fy), and feed force (Fz)) in hard finish turning processes of hardened 42CrMo4 (52 HRC) material was investigated experimentally. Taguchi’s mixed level parameter design (L18) is used for the experimental design (2x1,3x3). The signal-to-noise ratio (S/N) was used in the evaluation of test results.  By using Taguchi method, cutting parameters giving optimum surface roughness and cutting forces were determined. Regression analyses are applied to predict surface roughness and cutting forces. Analysis of variance (ANOVA) is used to determine the effects of the machining parameters on surface roughness and cutting forces. According to ANOVA analysis, the most important cutting parameters were found to be feed rate for surface roughness and depth of cut among cutting forces.  By conducting validation experiments, optimization was seen to be applied successfully.

Modeling and Analysis of Cutting Forces in Hard Turning T250 Steel Using CBN Tools

2010 ◽  
Vol 154-155 ◽  
pp. 694-700
Author(s):  
Yue Ding ◽  
Xi Bin Wang ◽  
Li Jing Xie ◽  
Hao Yang
Keyword(s):  
Cutting Force ◽  
Analysis Of Variance ◽  
Feed Rate ◽  
Cutting Forces ◽  
Hard Turning ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Depth Of Cut ◽  
Modeling And Analysis ◽  
Feed Force

The objective of this paper is to study the cutting forces in hard turning T250 steel with CBN tools. Experiments based on the Box-Behnken design were conducted to develop the cutting forces models by response surface methodology (RSM). Significance tests of the model are performed by the analysis of variance (ANOVA). It is also discussed the effects of cutting parameters (cutting speed, feed rate and depth of cut) on the cutting force components. The results show that the models can fit experimental data via analysis of variance. The most important cutting parameter is depth of cut, followed by feed rate, while the effect of cutting speed can be neglected. Compared to cutting force and feed force, thrust force is the largest. In addition, the cutting forces generated by the uncoated tool are smaller than by the coated one due to tool wear.

Determination of grinding parameters of fenugreek seed

1970 ◽  
Vol 26 (1) ◽  
pp. 16 ◽  
Author(s):  
S Balasubramanian ◽  
Rajkumar Rajkumar ◽  
K K Singh
Keyword(s):  
Particle Size ◽  
Energy Consumption ◽  
Moisture Content ◽  
Specific Energy ◽  
Feed Rate ◽  
Average Particle Size ◽  
Specific Energy Consumption ◽  
Average Particle ◽  
Fenugreek Seeds ◽  
Fenugreek Seed

Experiment to identify ambient grinding conditions and energy consumed was conducted for fenugreek. Fenugreek seeds at three moisture content (5.1%, 11.5% and 17.3%, d.b.) were ground using a micro pulverizer hammer mill with different grinding screen openings (0.5, 1.0 and 1.5 mm) and feed rate (8, 16 and 24 kg h-1) at 3000 rpm. Physical properties of fenugreek seeds were also determined. Specific energy consumptions were found to decrease from 204.67 to 23.09 kJ kg-1 for increasing levels of feed rate and grinder screen openings. On the other hand specific energy consumption increased with increasing moisture content. The highest specific energy consumption was recorded for 17.3% moisture content and 8 kg h-1 feed rate with 0.5 mm screen opening. Average particle size decreased from 1.06 to 0.39 mm with increase of moisture content and grinder screen opening. It has been observed that the average particle size was minimum at 0.5 mm screen opening and 8 kg h-1 feed rate at lower moisture content. Bond’s work index and Kick’s constant were found to increase from 8.97 to 950.92 kWh kg-1 and 0.932 to 78.851 kWh kg-1 with the increase of moisture content, feed rate and grinder screen opening, respectively. Size reduction ratio and grinding effectiveness of fenugreek seed were found to decrease from 4.11 to 1.61 and 0.0118 to 0.0018 with the increase of moisture content, feed rate and grinder screen opening, respectively. The loose and compact bulk densities varied from 219.2 to 719.4 kg m-3 and 137.3 to 736.2 kg m-3, respectively.  

Cutting Temperature and Cutting Forces Investigation Based on the Taguchi Design Method when High-Speed Milling of Titanium Matrix Composites with PCD Tool

2016 ◽  
Vol 836-837 ◽  
pp. 168-174 ◽  
Author(s):  
Ying Fei Ge ◽  
Hai Xiang Huan ◽  
Jiu Hua Xu
Keyword(s):  
Cutting Force ◽  
Feed Rate ◽  
Cutting Forces ◽  
High Speed ◽  
Volume Fraction ◽  
Cutting Temperature ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
High Speed Milling ◽  
Radial Depth

High-speed milling tests were performed on vol. (5%-8%) TiCp/TC4 composite in the speed range of 50-250 m/min using PCD tools to nvestigate the cutting temperature and the cutting forces. The results showed that radial depth of cut and cutting speed were the two significant influences that affected the cutting forces based on the Taguchi prediction. Increasing radial depth of cut and feed rate will increase the cutting force while increasing cutting speed will decrease the cutting force. Cutting force increased less than 5% when the reinforcement volume fraction in the composites increased from 0% to 8%. Radial depth of cut was the only significant influence factor on the cutting temperature. Cutting temperature increased with the increasing radial depth of cut, feed rate or cutting speed. The cutting temperature for the titanium composites was 40-90 °C higher than that for the TC4 matrix. However, the cutting temperature decreased by 4% when the reinforcement's volume fraction increased from 5% to 8%.

FRACTAL-BASED ANALYSIS OF THE VARIATIONS OF CUTTING FORCES ALONG DIFFERENT AXES IN END MILLING OPERATION

Fractals ◽  
2018 ◽  
Vol 26 (06) ◽  
pp. 1850089 ◽  
Author(s):  
HAMIDREZA NAMAZI ◽  
ALI AKHAVAN FARID ◽  
TECK SENG CHANG
Keyword(s):  
Fractal Dimension ◽  
Cutting Force ◽  
Cutting Forces ◽  
End Milling ◽  
Fractal Theory ◽  
Radial Force ◽  
Machining Conditions ◽  
Feed Force ◽  
Milling Operation ◽  
Force Signal

Analysis of cutting forces in machining operation is an important issue. The cutting force changes randomly in milling operation where it makes a signal by plotting over time span. An important type of analysis belongs to the study of how cutting forces change along different axes. Since cutting force has fractal characteristics, in this paper for the first time we analyze the variations of complexity of cutting force signal along different axes using fractal theory. For this purpose, we consider two cutting depths and do milling operation in dry and wet machining conditions. The obtained cutting force time series was analyzed by computing the fractal dimension. The result showed that in both wet and dry machining conditions, the feed force (along [Formula: see text]-axis) has greater fractal dimension than radial force (along [Formula: see text]-axis). In addition, the radial force (along [Formula: see text]-axis) has greater fractal dimension than thrust force (along [Formula: see text]-axis). The method of analysis that was used in this research can be applied to other machining operations to study the variations of fractal structure of cutting force signal along different axes.

scholarly journals Forecasting values of cutting power for the sawing process of impregnated pine wood on band sawing machine

Mechanik ◽  
2018 ◽  
Vol 91 (8-9) ◽  
pp. 766-768 ◽  
Author(s):  
Daniel Chuchała ◽  
Kazimierz A. Orłowski
Keyword(s):  
Fracture Mechanics ◽  
Pinus Sylvestris ◽  
Scots Pine ◽  
Cutting Forces ◽  
Classical Method ◽  
Cutting Power ◽  
Cutting Resistance ◽  
Innovative Method ◽  
Predicted Values ◽  
Sawing Process

In this paper the predicted values of cutting power for band sawing machine (ST100R), which is used in the Polish sawmills, were presented. The values of cutting power were determined for wood of Scots pine (Pinus sylvestris L.), which was impregnated and not impregnated. These values were estimated using an innovative method of forecasting cutting forces, which takes into account the elements of fracture mechanics. The forecasts obtained in this way are compared with the values of cutting power estimated with the use of the classical method, which is based on the specific cutting resistance.

Characterizing the Effect of Cutting Condition, Tool Path, and Heat Treatment on Cutting Forces of Selective Laser Melting Spherical Component in Five-Axis Milling

2018 ◽  
Vol 140 (5) ◽  
Author(s):  
Amir Mahyar Khorasani ◽  
Ian Gibson ◽  
Moshe Goldberg ◽  
Guy Littlefair
Keyword(s):  
Heat Treatment ◽  
Production Process ◽  
Cutting Force ◽  
Feed Rate ◽  
Cutting Forces ◽  
Tool Path ◽  
Annealing Temperature ◽  
Spindle Speed ◽  
Cutting Condition ◽  
Scallop Height

Additive manufacturing (AM), partly due to its compatibility with computer-aided design (CAD) and fabrication of intricate shapes, is an emerging production process. Postprocessing, such as machining, is particularly necessary for metal AM due to the lack of surface quality for as-built parts being a problem when using as a production process. In this paper, a predictive model for cutting forces has been developed by using artificial neural networks (ANNs). The effect of tool path and cutting condition, including cutting speed, feed rate, machining allowance, and scallop height, on the generated force during machining of spherical components such as prosthetic acetabular shell was investigated. Also, different annealing processes like stress relieving, mill annealing and β annealing have been carried out on the samples to better understand the effect of brittleness, strength, and hardness on machining. The results of this study showed that ANN can accurately apply to model cutting force when using ball nose cutters. Scallop height has the highest impact on cutting forces followed by spindle speed, finishing allowance, heat treatment/annealing temperature, tool path, and feed rate. The results illustrate that using linear tool path and increasing annealing temperature can result in lower cutting force. Higher cutting force was observed with greater scallop height and feed rate while for higher finishing allowance, cutting forces decreased. For spindle speed, the trend of cutting force was increasing up to a critical point and then decreasing due to thermal softening.

Predictive Modeling and Optimization of Cutting Forces Through RSM and Taguchi Techniques in the Turning of ASTM B574 (Hastelloy C-22)

2018 ◽  
pp. 398-417
Author(s):  
İsmail Kırbaş ◽  
Musa Peker ◽  
Gültekin Basmacı ◽  
Mustafa Ay
Keyword(s):  
Feed Rate ◽  
Cutting Forces ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Rake Angle ◽  
Orthogonal Experimental Design ◽  
Depth Of Cut ◽  
Effective Parameters ◽  
Factors Affecting ◽  
The Impact

In this chapter, the impact of cutting parameters (depth of cut, cutting speed, feed, flow, rake angle, lead angle) on cutting forces in the turning process with regard to ASTM B574 (Hastelloy C-22) material has been investigated. Variance analysis has been applied in order to determine the factors affecting the cutting forces. The optimization of the parameters affecting the surface roughness has been obtained using response surface methodology (RSM) based on the Taguchi orthogonal experimental design. The accuracy of the developed models required for the estimation of the force values (Fx, Fy, Fz) is quite successful. In this study, where the R2 value has been used as the criterion/measure, accuracy values of 93.35%, 95.03%, and 95.09% have been achieved for Fx, Fy, and Fz, respectively. As a result of the ANOVA analysis, the most effective parameters for Fx at a 95% confidence interval are depth of cut, feed rate, flow, and rake angle. The most effective parameter for Fy is depth of cut, while the most effective parameters for Fz are depth of cut, feed rate, and flow, respectively.

Sign in / Sign up

Export Citation Format

Share Document