scholarly journals Yttrium Oxide Freeze-Casts: Target Materials for Radioactive Ion Beams

Materials ◽  
2021 ◽  
Vol 14 (11) ◽  
pp. 2864
Author(s):  
Eva Kröll ◽  
Miriana Vadalà ◽  
Juliana Schell ◽  
Simon Stegemann ◽  
Jochen Ballof ◽  
...  
Keyword(s):  
Pore Structure ◽  
Yttrium Oxide ◽  
Ion Beam ◽  
Isotope Separation ◽  
Target Material ◽  
Ion Beams ◽  
Radioactive Isotopes ◽  
Solid Loading ◽  
Radioactive Ion Beams ◽  
Freeze Casting

Highly porous yttrium oxide is fabricated as ion beam target material in order to produce radioactive ion beams via the Isotope Separation On Line (ISOL) method. Freeze casting allows the formation of an aligned pore structure in these target materials to improve the isotope release. Aqueous suspensions containing a solid loading of 10, 15, and 20 vol% were solidified with a unidirectional freeze-casting setup. The pore size and pore structure of the yttrium oxide freeze-casts are highly affected by the amount of solid loading. The porosity ranges from 72 to 84% and the crosslinking between the aligned channels increases with increasing solid loading. Thermal aging of the final target materials shows that an operation temperature of 1400 °C for 96 h has no significant effect on the microstructure. Thermo-mechanical calculation results, based on a FLUKA simulation, are compared to measured compressive strength and forecast the mechanical integrity of the target materials during operation. Even though they were developed for the particular purpose of the production of short-lived radioactive isotopes, the yttria freeze-cast scaffolds can serve multiple other purposes, such as catalyst support frameworks or high-temperature fume filters.

scholarly journals The ISOLPHARM project: A New ISOL production method of high specific activity beta-emitting radionuclides as radiopharmaceutical precursors

2018 ◽  
Vol 48 ◽  
pp. 1860103 ◽  
Author(s):  
A. Andrighetto ◽  
F. Borgna ◽  
M. Ballan ◽  
S. Corradetti ◽  
E. Vettorato ◽  
...  
Keyword(s):  
Nuclear Reactions ◽  
Specific Activity ◽  
Isotope Separation ◽  
High Specific Activity ◽  
Target Material ◽  
Mass Range ◽  
Production Method ◽  
Radioactive Isotopes ◽  
Innovative Technology ◽  
On Line

The ISOLPHARM project explores the feasibility of exploiting an innovative technology to produce extremely high specific activity beta-emitting radionuclides as radiopharmaceutical precursors. This technique is expected to produce radiopharmaceuticals that are virtually mainly impossible to obtain in standard production facilities, at lower cost and with less environmental impact than traditional techniques. The groundbreaking ISOLPHARM method investigated in this project has been granted an international patent (INFN). As a component of the SPES (Selective Production of Exotic Species) project at the Istituto Nazionale di Fisica Nucleare–Laboratori Nazionali di Legnaro (INFN–LNL), a new facility will produce radioactive ion beams of neutron-rich nuclei with high purity and a mass range of 80–160 amu. The radioactive isotopes will result from nuclear reactions induced by accelerating 40 MeV protons in a cyclotron to collide on a target of UC[Formula: see text]. The uranium in the target material will be [Formula: see text]U, yielding radioactive isotopes that belong to elements with an atomic number between 28 and 57. Isotope separation on line (ISOL) is adopted in the ISOLPHARM project to obtain pure isobaric beams for radiopharmaceutical applications, with no isotopic contaminations in the beam or subsequent trapping substrate. Isobaric contaminations may potentially affect radiochemical and radionuclide purity, but proper methods to separate chemically different elements can be developed.

Purification of Radioactive Ion Beams by Photodetachment in a RF Quadrupole Ion Beam Cooler

2009 ◽  
Author(s):  
Y. Liu ◽  
C. C. Havener ◽  
T. L. Lewis ◽  
A. Galindo-Uribarri ◽  
J. R. Beene ◽  
...  
Keyword(s):  
Ion Beam ◽  
Ion Beams ◽  
Radioactive Ion Beams

Production of intense radioactive beams at ISAC using low-energy protons

2006 ◽  
Vol 84 (4) ◽  
pp. 325-333 ◽  
Author(s):  
M Trinczek ◽  
S Lapi ◽  
B Guo ◽  
F Ames ◽  
K R Buckley ◽  
...  
Keyword(s):  
Isotope Separation ◽  
Nuclear Astrophysics ◽  
Ion Beams ◽  
Low Energy ◽  
Radioactive Ion Beams ◽  
Radioactive Beams ◽  
On Line ◽  
Mev Protons ◽  
Proof Of Principle

A proof-of-principle approach for the production of intense (~108/s) radioactive ion beams, which differs from the standard ISOL (Isotope Separation On-Line) technique, has been demonstrated successfully using 11C at the TRIUMF laboratory. This approach uses 13 MeV protons produced by a medical cyclotron and should be useful for a range of radioisotopes of interest to the nuclear astrophysics research programme.PACS No.: 29.25.Rm

scholarly journals Porous Silicon as a Platform for Radiation Theranostics Together with a Novel RIB-Based Radiolanthanoid

2019 ◽  
Vol 2019 ◽  
pp. 1-9 ◽  
Author(s):  
Ulrika Jakobsson ◽  
Ermei Mäkilä ◽  
Anu J. Airaksinen ◽  
Osku Alanen ◽  
Asenath Etilé ◽  
...  
Keyword(s):  
Prostate Cancer ◽  
Porous Silicon ◽  
Ex Vivo ◽  
Ion Beam ◽  
Ion Beams ◽  
Radioactive Ion Beams ◽  
Mesoporous Silicon ◽  
Main Site ◽  
The Stability

Mesoporous silicon (PSi) is biocompatible and tailorable material with high potential in drug delivery applications. Here, we report of an evaluation of PSi as a carrier platform for theranostics by delivering a radioactive ion beam- (RIB-) based radioactive lanthanoid into tumors in a mouse model of prostate carcinoma. Thermally hydrocarbonized porous silicon (THCPSi) wafers were implanted with 159Dy at the facility for radioactive ion beams ISOLDE located at CERN, and the resulting [159Dy]THCPSi was postprocessed into particles. The particles were intratumorally injected into mice bearing prostate cancer xenografts. The stability of the particles was studied in vivo, followed by ex vivo biodistribution and autoradiographic studies. We showed that the process of producing radionuclide-implanted PSi particles is feasible and that the [159Dy]THCPSi particles stay stable and local inside the tumor over seven days. Upon release of 159Dy from the particles, the main site of accumulation is in the skeleton, which is in agreement with previous studies on the biodistribution of dysprosium. We conclude that THCPSi particles are a suitable platform together with RIB-based radiolanthanoids for theranostic purposes as they are retained after administration inside the tumor and the radiolanthanoid remains embedded in the THCPSi.

Preparation of Oriented Porous Silicon Carbide Bodies by Freeze-Casting Process

2007 ◽  
Vol 280-283 ◽  
pp. 1287-1290 ◽  
Author(s):  
Jie Tang ◽  
Yu Feng Chen ◽  
Hua Wang ◽  
Hai Lin Liu ◽  
Qi Sheng Fan
Keyword(s):  
Silicon Carbide ◽  
Carbon Black ◽  
Pore Structure ◽  
Pore Size ◽  
Casting Process ◽  
Porous Ceramics ◽  
Solid Loading ◽  
Gradual Change ◽  
Freeze Casting ◽  
Freezing Condition

Porous ceramics green bodies of silicon carbide were formed by freeze-casting of silicon carbide/carbon black aqueous slurries in a mold where temperature distribution was controlled. The influence of solid loading on the pore structure of green bodies was investigated. Pore morphology of green bodies formed from slurries with various solid loading ranging from 25 to 50vol% experienced a gradual change. Appropriate solid loading of silicon carbide/carbon black slurry was concluded for fabrication of SiC ceramics with oriented pore structure. Two means were employed for changing ice crystallizing velocity, so that the influence of ice crystallizing velocity on pore size of green bodies was explored. It was concluded that pore size became larger under slow freezing condition, whereas smaller with the pre-cooling of silicon carbide/carbon black slurry.

scholarly journals Opportunities for nuclear reaction studies at future facilities

2019 ◽  
Vol 22 ◽  
pp. 10
Author(s):  
M. Veselsky ◽  
J. Klimo ◽  
N. Vujisicova ◽  
G. A. Souliotis
Keyword(s):  
Nuclear Reaction ◽  
High Power ◽  
Nuclear Physics ◽  
Nuclear Reactions ◽  
Ion Beam ◽  
Ion Beams ◽  
Radioactive Ion Beams ◽  
High Power Laser ◽  
Power Laser ◽  
The Future

Opportunities for investigations of nuclear reactions at the future nuclear physics facilities such as radioactive ion beam facilities and high-power laser facilities are considered. Post-accelerated radioactive ion beams offer possibilities for study of the role of isospin asymmetry in the reaction mechanisms at various beam energies. Fission barrier heights of neutron-deficient nuclei can be directly determined at low energies. Post-accelerated radioactive ion beams, specifically at the future facilities such as HIE-ISOLDE, SPIRAL-2 or RAON-RISP can be also considered as a candidate for production of very neutron-rich nuclei via mechanism of multi-nucleon transfer. High-power laser facilities such as ELI-NP offer possibilities for nuclear reaction studies with beams of unprecedented properties. Specific cases such as ternary reactions or even production of super-heavy elements are considered.

scholarly journals Atomic Layer Deposition and Vapor Deposited SAMS in a CrossBeam FIB-SEM Platform: A Path To Advanced Materials Synthesis

2009 ◽  
Vol 17 (2) ◽  
pp. 18-25
Author(s):  
E. L. Principe ◽  
Cheryl Hartfield ◽  
Rocky Kruger ◽  
Aaron Smith ◽  
Ray Dubois ◽  
...  
Keyword(s):  
Electron Beam ◽  
Ion Beam ◽  
Three Dimensional ◽  
Target Material ◽  
Chemical Vapor ◽  
Ion Beams ◽  
Two Dimensions ◽  
Nanometer Scale ◽  
Direct Write ◽  
Etch Pattern

Nanopatterning refers to the fabrication of nanometer-scale structures, meaning patterns with at least one lateral dimension between the size of an individual atom and approximately 100 nm. Direct Write or Maskless Lithography as discussed in this article refers to the use of a focused beam, either an ion beam or an electron beam, to create a patterned image directly into (etch), or on top of (deposition), the target material. Both electron beams and ion beams can be used together with gas injection technology to deposit three dimensional structures on the nanometer scale through the process of either electron beam assisted or ion beam assisted chemical vapor deposition (CVD). The deposition occurs only in the vicinity where the electron beam or ion beam is being scanned. Therefore, the deposit will follow the form of the scanned beam in two dimensions. This approach can be applied to produce three-dimensional objects by successively layering upon the two-dimensional pattern. In the case of ion beams in particular, the direct write process can also produce an etch pattern on the nanometer scale as the ion beam physically mills away the material via ion bombardment. This process can also be chemically enhanced for certain materials such as simultaneous use of water to selectively etch carbon.

Preparation of TEM samples by focused ion beams

1995 ◽  
Vol 53 ◽  
pp. 518-519
Author(s):  
John F. Walker ◽  
J C Reiner ◽  
C Solenthaler
Keyword(s):  
Integrated Circuit ◽  
Polycrystalline Silicon ◽  
Field Effect Transistor ◽  
High Spatial Resolution ◽  
Ion Beam ◽  
Ion Beams ◽  
Focused Ion Beams ◽  
Precise Location ◽  
Effect Transistor ◽  
Circuit Technology

The high spatial resolution available from TEM can be used with great advantage in the field of microelectronics to identify problems associated with the continually shrinking geometries of integrated circuit technology. In many cases the location of the problem can be the most problematic element of sample preparation. Focused ion beams (FIB) have previously been used to prepare TEM specimens, but not including using the ion beam imaging capabilities to locate a buried feature of interest. Here we describe how a defect has been located using the ability of a FIB to both mill a section and to search for a defect whose precise location is unknown. The defect is known from electrical leakage measurements to be a break in the gate oxide of a field effect transistor. The gate is a square of polycrystalline silicon, approximately 1μm×1μm, on a silicon dioxide barrier which is about 17nm thick. The break in the oxide can occur anywhere within that square and is expected to be less than 100nm in diameter.

Atomic force microscopy (AFM) of the topography of silicon surfaces exposed to ion beams

1992 ◽  
Vol 50 (2) ◽  
pp. 1132-1133
Author(s):  
Mark Denker ◽  
Jennifer Wall ◽  
Mark Ray ◽  
Richard Linton
Keyword(s):  
Secondary Ion Mass Spectrometry ◽  
Incidence Angle ◽  
Ion Beam ◽  
Depth Profiling ◽  
Depth Resolution ◽  
Ion Beams ◽  
Scanning Tunneling ◽  
Tunneling Microscopy ◽  
Trace Impurities ◽  
Energy Dose

Reactive ion beams such as O2+ and Cs+ are used in Secondary Ion Mass Spectrometry (SIMS) to analyze solids for trace impurities. Primary beam properties such as energy, dose, and incidence angle can be systematically varied to optimize depth resolution versus sensitivity tradeoffs for a given SIMS depth profiling application. However, it is generally observed that the sputtering process causes surface roughening, typically represented by nanometer-sized features such as cones, pits, pyramids, and ripples. A roughened surface will degrade the depth resolution of the SIMS data. The purpose of this study is to examine the relationship of the roughness of the surface to the primary ion beam energy, dose, and incidence angle. AFM offers the ability to quantitatively probe this surface roughness. For the initial investigations, the sample chosen was <100> silicon, and the ion beam was O2+.Work to date by other researchers typically employed Scanning Tunneling Microscopy (STM) to probe the surface topography.

Sign in / Sign up

Export Citation Format

Share Document