scholarly journals Mechanical Properties of Low-Performance Concrete (LPC) and Shear Capacity of Old Unreinforced LPC Squat Walls

Materials ◽  
2021 ◽  
Vol 14 (23) ◽  
pp. 7310
Author(s):  
Rami Eid ◽  
Avraham N. Dancygier ◽  
Ghali Jaber
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Shear Capacity ◽  
Compression Tests ◽  
Diagonal Compression ◽  
Load Carrying ◽  
Mode Of Failure ◽  
Major Principal Stress ◽  
Low Performance ◽  
Squat Walls

Low-performance concrete (LPC) is characterized by its low strength and commonly by the presence of large aggregates. This type of concrete was used for construction of load carrying, commonly unreinforced walls in old buildings. The resistance of these buildings with LPC squat walls (of relatively low height-to-length ratio), to in plane horizontal loads, was experimentally investigated in this study. The low compressive strength of these walls, well below that of standard concrete, requires estimation of the relation between the actual LPC compressive strength and its tensile strength, and identification of their failure mode and corresponding shear capacity when subjected to in plane horizontal loads. In this study, compressive and splitting tensile strengths of authentic LPC specimens were measured, and based on them, a relation between the compressive and tensile strengths is proposed. Then, diagonal compression tests were performed on authentic LPC specimens, as well as specimens made of standard concrete. These tests yielded the expected mode of failure of vertical cracking and their analysis shows that their shear capacity needs to be evaluated based on their tensile strength (rather than the flexural shear capacity of unreinforced concrete beams). Thus, the load-bearing (both horizontal and gravitational) capacity to prevent diagonal tension failure of an unreinforced LPC wall can be evaluated by comparing the LPC tensile strength to the major principal stress caused by the load. Assessment of the tensile strength can be based on the relation between the compressive and tensile strengths proposed in this work.

Improving the structural performance of reinforced geopolymer concrete incorporated with hazardous heavy metal waste ash

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Suresh Kumar Arunachalam ◽  
Muthukannan Muthiah ◽  
Kanniga Devi Rangaswamy ◽  
Arunkumar Kadarkarai ◽  
Chithambar Ganesh Arunasankar
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Medical Waste ◽  
Source Material ◽  
Geopolymer Concrete ◽  
Deformation Capacity ◽  
Cement Concrete ◽  
Content Type ◽  
Load Carrying ◽  
Reinforced Cement

Purpose Demand for Geopolymer concrete (GPC) has increased recently because of its many benefits, including being environmentally sustainable, extremely tolerant to high temperature and chemical attacks in more dangerous environments. Like standard concrete, GPC also has low tensile strength and deformation capacity. This paper aims to analyse the utilization of incinerated bio-medical waste ash (IBWA) combined with ground granulated blast furnace slag (GGBS) in reinforced GPC beams and columns. Medical waste was produced in the health-care industry, specifically in hospitals and diagnostic laboratories. GGBS is a form of industrial waste generated by steel factories. The best option to address global warming is to reduce the consumption of Portland cement production and promote other types of cement that were not a pollutant to the environment. Therefore, the replacement in ordinary Portland cement construction with GPC is a promising way of reducing carbon dioxide emissions. GPC was produced due to an alkali-activated polymeric reaction between alumina-silicate source materials and unreacted aggregates and other materials. Industrial pollutants such as fly ash and slag were used as raw materials. Design/methodology/approach Laboratory experiments were performed on three different proportions (reinforced cement concrete [RCC], 100% GGBS as an aluminosilicate source material in reinforced geopolymer concrete [GRGPC] and 30% replacement of IBWA as an aluminosilicate source material for GGBS in reinforced geopolymer concrete [IGRGPC]). The cubes and cylinders for these proportions were tested to find their compressive strength and split tensile strength. In addition, beams (deflection factor, ductility factor, flexural strength, degradation of stiffness and toughness index) and columns (load-carrying ability, stress-strain behaviour and load-deflection behaviours) of reinforced geopolymer concrete (RGPC) were studied. Findings As shown by the results, compared to Reinforced Cement Concrete (RCC) and 100% GGBS based Reinforced Geopolymer Concrete (GRGPC), 30% IBWA and 70% GGBS based Reinforced Geopolymer Concrete (IGRGPC) (30% IBWA–70% GGBS reinforced geo-polymer concrete) cubes, cylinders, beams and columns exhibit high compressive strength, tensile strength, flexural strength, load-carrying ability, ultimate strength, stiffness, ductility and deformation capacity. Originality/value All the results were based on the experiments done in this research. All the result values obtained in this research are higher than the theoretical values.

Grout Injection Effect on the Shear Behavior of FRCM Strengthened Stone Masonry Panels

2019 ◽  
Vol 817 ◽  
pp. 552-559
Author(s):  
Francesca Ferretti ◽  
Andrea Incerti ◽  
Anna Rosa Tilocca ◽  
Claudio Mazzotti
Keyword(s):  
Shear Capacity ◽  
Stone Masonry ◽  
Masonry Structures ◽  
Compression Tests ◽  
Grout Injection ◽  
Structural Element ◽  
Diagonal Compression ◽  
Two Samples ◽  
Injection Effect

During the last decades, several seismic phenomena have shown the high vulnerability of existing stone masonry structures subject to horizontal actions. Innovative composite materials, such as Fiber Reinforced Cementitious Matrix (FRCM), can be adopted for the retrofitting of masonry structures. The use of these innovative FRCM systems is usually combined with a more traditional retrofitting technique: grout injection. It allows to restore or improve the transversal connection between wall leaves, ensuring a monolithic behavior of the structural element. The objective of this research was to analyze the effect of the quality of the grout injection on the shear response of FRCM strengthened stone masonry panels. Results from an experimental campaign, where stone masonry specimens were subject to diagonal compression tests, are therefore presented in this paper. Two samples were subject to grout injection and one of them was strengthened with Steel Reinforced Grout (SRG). Comparisons between the experimental results showed that grout injection alone, if correctly executed, could determine a significant improvement in the shear capacity of masonry panels. The application of the FRCM strengthening system could further enhance the behavior of the samples, especially influencing the failure mode. Comparisons with analytical formulations for the evaluation of the capacity of strengthened walls are also presented.

scholarly journals Experimental Study on Influence of Methylcellulose on Tensile and Flexural Strength of Normal Strength Ordinary Portland Cement Concrete

2021 ◽  
Vol 40 (4) ◽  
pp. 703-713
Author(s):  
Ali Ahmed ◽  
Shakir Ahmad ◽  
Muhammad Mannal Kaleem ◽  
Muhammad Bilal Zahid
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Flexural Strength ◽  
Control Sample ◽  
Modulus Of Rupture ◽  
Compression Tests ◽  
Portland Cement Concrete ◽  
Concrete Cylinder ◽  
Compressive Strength Of Concrete ◽  
Normal Strength

Current study explores the possibility of improvement in various categories of concrete’s strengths (including tensile strength, flexural strength etc.) by using methylcellulose as an additive. The effect of methylcellulose on concrete’s compressive strength has also been investigated experimentally. Concrete samples were casted with several methylcellulose to binder ratios varying from 0.002 to 0.01 by weight of cement. Several tests were performed on concrete specimens including concrete cylinder and cube compression tests, split cylinder tests and modulus of rupture tests. Results showed that addition of methylcellulose increased the tensile strength of concrete. Addition of 0.2% of methylcellulose increased the tensile strength of concrete by 16%. This increase in tensile strength reached up to 73% of the control sample on addition of 1% methylcellulose. It was observed that the effect of methylcellulose on compressive strength of concrete depends upon the type of samples being tested (cube or cylinder). The compressive strength of concrete cylinders showed a plateau behavior with peak at 0.4% methylcellulose content with an increase of 18.7%. Effect of methylcellulose on concrete cylinder strength becomes insignificant beyond 0.6%. It was observed that addition of methylcellulose reduces the modulus of rupture values. The reduction in MOR was only 3% at 0.2% methylcellulose content but it grew to 30% at 1% methylcellulose content. The research presents an effective way of increasing tensile strength of concrete but without significant effect on concrete’s compressive strength and modulus of rupture values. These findings can be used to determine optimum content of methylcellulose to achieve desired performance from concrete depending upon the intended use.

Experimental and Analytical Investigation of Steel Reinforced Grout (SRG) Strengthened Masonry Panels

2017 ◽  
Vol 747 ◽  
pp. 226-233
Author(s):  
Xuan Wang ◽  
Chi Chiu Lam ◽  
Vai Pan Iu ◽  
Kun Pang Kou
Keyword(s):  
Load Capacity ◽  
Experimental Tests ◽  
Analytical Investigation ◽  
Experimental Program ◽  
Load Carrying Capacity ◽  
Compression Tests ◽  
Clay Brick ◽  
Diagonal Compression ◽  
Load Carrying ◽  
Externally Bonded

This paper illustrates the results of experimental and analytical investigation carried out on masonry panels built by grey clay brick (GCB) from the Lingnan Region, China, reinforced with externally bonded Steel Reinforced Grout (SRG) system. The experimental program involves diagonal compression tests on two unreinforced and two double side reinforced panels. The main outcomes of the experimental tests include load-displacement response, stiffness, load capacity and failure mechanism. The results show that the contribution of the strengthening system to the increase of the load carrying capacity and ductility. Finally, analytical model is proposed and compared with experimental results.

Shear Capacity of Masonry Panels Reinforced with Inorganic Strengthening Systems

2019 ◽  
Vol 817 ◽  
pp. 486-492
Author(s):  
Marta Del Zoppo ◽  
Gennaro Maddaloni ◽  
Alberto Balsamo ◽  
Marco di Ludovico ◽  
Andrea Prota
Keyword(s):  
Composite Materials ◽  
Shear Capacity ◽  
Masonry Walls ◽  
Masonry Buildings ◽  
Compression Tests ◽  
Plane Shear ◽  
Diagonal Compression ◽  
The University ◽  
Fabric Reinforced Cementitious Matrix ◽  
Inorganic Composite

Unreinforced masonry buildings are particularly vulnerable to brittle failures during seismic events due to the poor in-plane shear capacity of masonry walls. The use of strengthening solutions with polymeric matrices is not often recommended for masonry buildings, due to breathability issues, and the adoption of inorganic matrices is sometimes considered preferable. In this paper, the use of inorganic composite materials for improving the in-plane shear capacity of tuff masonry walls is investigated. The experimental data from 83 diagonal compression tests carried out at the University of Naples Federico II in recent years have been collected and the main results are herein discussed to outline the main features of different strengthening techniques with inorganic composite materials such as Reinforced Plaster (RP), Composite Reinforced Mortar (CRM) and Fabric Reinforced Cementitious Matrix (FRCM).

Variasi Penambahan Sika Cim Dan Fiber Kawat Pada Beton Mutu Fc’ 30 Mpa

2018 ◽  
Vol 9 (2) ◽  
pp. 67-73
Author(s):  
M Zainul Arifin
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Curing Temperature ◽  
Test Results ◽  
Concrete Compressive Strength ◽  
Normal Concrete ◽  
Astm Method ◽  
Additive Type ◽  
Composition Variation ◽  
Compressive Strength Of Concrete

This research was conducted to determine the value of the highest compressive strength from the ratio of normal concrete to normal concrete plus additive types of Sika Cim with a composition variation of 0.25%, 0.50%, 0.75%, 1.00%, 1.25%, 1 , 50% and 1.75% of the weight of cement besides that in this study also aims to find the highest tensile strength from the ratio of normal concrete to normal concrete in the mixture of sika cim composition at the highest compressive strength above and after that added fiber wire with a size diameter of 1 mm in length 100 mm with a ratio of 1% of material weight. The concrete mix plan was calculated using the ASTM method, the matrial composition of the normal concrete mixture as follows, 314 kg / m3 cement, 789 kg / m3 sand, 1125 kg / m3 gravel and 189 liters / m3 of water at 10 cm slump, then normal concrete added variations of the composition of sika cim 0.25%, 0.50%, 0.75%, 1.00%, 1.25%, 1.5%, 1.75% by weight of cement and fiber, the tests carried out were compressive strength of concrete and tensile strength of concrete, normal maintenance is soaked in fresh water for 28 days at 30oC. From the test results it was found that the normal concrete compressive strength at the age of 28 days was fc1 30 Mpa, the variation in the addition of the sika cim additive type mineral was achieved in composition 0.75% of the cement weight of fc1 40.2 Mpa 30C. Besides that the tensile strength test results were 28 days old with the addition of 1% fiber wire mineral to the weight of the material at a curing temperature of 30oC of 7.5%.

A method for measuring the in-plane compressive strength and the compression behavior of coating layers

TAPPI Journal ◽  
2011 ◽  
Vol 10 (7) ◽  
pp. 29-34
Author(s):  
TEEMU PUHAKKA ◽  
ISKO KAJANTO ◽  
NINA PYKÄLÄINEN
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Calcium Carbonate ◽  
Coating Layer ◽  
Test Methods ◽  
Coating Films ◽  
Precipitated Calcium Carbonate ◽  
Coating Color ◽  
Mineral Coatings ◽  
Styrene Butadiene

Cracking at the fold is a quality defect sometimes observed in coated paper and board. Although tensile and compressive stresses occur during folding, test methods to measure the compressive strength of a coating have not been available. Our objective was to develop a method to measure the compressive strength of a coating layer and to investigate how different mineral coatings behave under compression. We used the short-span compressive strength test (SCT) to measure the in-plane compressive strength of a free coating layer. Unsupported free coating films were prepared for the measurements. Results indicate that the SCT method was suitable for measuring the in-plane compressive strength of a coating layer. Coating color formulations containing different kaolin and calcium carbonate minerals were used to study the effect of pigment particles’ shape on the compressive and tensile strengths of coatings. Latices having two different glass transition temperatures were used. Results showed that pigment particle shape influenced the strength of a coating layer. Platy clay gave better strength than spherical or needle-shaped carbonate pigments. Compressive and tensile strength decreased as a function of the amount of calcium carbonate in the coating color, particularly with precipitated calcium carbonate. We also assessed the influence of styrene-butadiene binder on the compressive strength of the coating layer, which increased with the binder level. The compressive strength of the coating layer was about three times the tensile strength.

Effect of combined drink cans and steel fibers on the impact resistance and mechanical properties of concrete

2020 ◽  
Vol 14 (2) ◽  
pp. 6734-6742
Author(s):  
A. Syamsir ◽  
S. M. Mubin ◽  
N. M. Nor ◽  
V. Anggraini ◽  
S. Nagappan ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Reinforced Concrete ◽  
Impact Resistance ◽  
Fiber Reinforced Concrete ◽  
Steel Fibers ◽  
Fiber Reinforced ◽  
Indirect Tensile ◽  
The Impact

This study investigated the combine effect of 0.2 % drink cans and steel fibers with volume fractions of 0%, 0.5%, 1%, 1.5%, 2%, 2.5% and 3% to the mechanical properties and impact resistance of concrete. Hooked-end steel fiber with 30 mm and 0.75 mm length and diameter, respectively was selected for this study.  The drinks cans fiber were twisted manually in order to increase friction between fiber and concrete. The results of the experiment showed that the combination of steel fibers and drink cans fibers improved the strength performance of concrete, especially the compressive strength, flexural strength and indirect tensile strength. The results of the experiment showed that the combination of steel fibers and drink cans fibers improved the compressive strength, flexural strength and indirect tensile strength by 2.3, 7, and 2 times as compare to batch 1, respectively. Moreover, the impact resistance of fiber reinforced concrete has increase by 7 times as compared to non-fiber concretes. Moreover, the impact resistance of fiber reinforced concrete consistently gave better results as compared to non-fiber concretes. The fiber reinforced concrete turned more ductile as the dosage of fibers was increased and ductility started to decrease slightly after optimum fiber dosage was reached. It was found that concrete with combination of 2% steel and 0.2% drink cans fibers showed the highest compressive, split tensile, flexural as well as impact strength.    

MEEHANITE GB300

Alloy Digest ◽  
2020 ◽  
Vol 69 (11) ◽  
Keyword(s):  
Thermal Conductivity ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Gray Cast Iron ◽  
High Strength ◽  
Heat Treating ◽  
Spheroidal Graphite ◽  
Cast Irons ◽  
Test Pieces ◽  
Temperature Performance

Abstract Meehanite GB300 is a pearlitic gray cast iron that has a minimum tensile strength of 300 MPa (44 ksi), when determined on test pieces machined from separately cast, 30 mm (1.2 in.) diameter test bars. This grade exhibits high strength while still maintaining good thermal conductivity and good machinability. It is generally used for applications where the thermal conductivity requirements preclude the use of other higher-strength materials, such as spheroidal graphite cast irons, which have inferior thermal properties. This datasheet provides information on physical properties, hardness, tensile properties, and compressive strength as well as fatigue. It also includes information on low and high temperature performance as well as heat treating, machining, and joining. Filing Code: CI-75. Producer or source: Meehanite Metal Corporation.

Sign in / Sign up

Export Citation Format

Share Document