scholarly journals Experimental Correlation of Mechanical Properties of the Ti-6Al-4V Alloy at Different Length Scales

Metals ◽  
2021 ◽  
Vol 11 (1) ◽  
pp. 104
Author(s):  
Víctor Tuninetti ◽  
Andrés Felipe Jaramillo ◽  
Guiomar Riu ◽  
Carlos Rojas-Ulloa ◽  
Amna Znaidi ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Flow Stress ◽  
Stress Fields ◽  
Analytical Relationship ◽  
Strain Hardening Exponent ◽  
Intrinsic Properties ◽  
Length Scales ◽  
Nanoindentation Testing ◽  
Α Phase ◽  
Composite Hardness

This article focuses on a systematic study of a Ti-6Al-4V alloy in order to extensively characterize the main mechanical properties at the macro-, micro- and submicrometric length scale under different stress fields. Hardness, elastic modulus, true stress–strain curves and strain-hardening exponent are correlated with the intrinsic properties of the α- and β-phases that constitute this alloy. A systematic characterization process followed, considering the anisotropic effect on both orthogonal crystallographic directions, as well as determining the intrinsic properties for the α-phase. An analytical relationship was established between the flow stress determined under different stress fields, testing geometries and length scales, highlighting that it is possible to estimate flow stress under compression and/or tensile loading from the composite hardness value obtained by instrumented nanoindentation testing.

Methodology of studying the mechanical properties of composite materials (reinforced concrete)

2018 ◽  
Vol 84 (12) ◽  
pp. 61-67
Author(s):  
V. A. Eryshev
Keyword(s):  
Mechanical Properties ◽  
Reinforced Concrete ◽  
Experimental Studies ◽  
Analytical Relationship ◽  
Hardened Concrete ◽  
Deformation Model ◽  
Joint Work ◽  
Concrete Shrinkage ◽  
Axial Tension ◽  
Tension And Compression

The mechanical properties of a complex composite material formed by steel and hardened concrete, are studied. A technique of operative quality control of new credible concrete and reinforcement, both in laboratory and field conditions is developed for determination of the strength and strain characteristics of materials, as well as cohesion forces determining their joint operation under load. The design of the mobile unit is presented. The unit provides a possibility of changing the direction of loading and testing the reinforced element of the given shape both for tension and compression. Moreover, the nomenclature of testing equipment and the number of molds for manufacturing concrete samples substantially decrease. Using the values of forcing resulting in concrete cracking when the joint work of concrete and reinforcement is disrupted the values of the inherent stresses and strains attributed to the concrete shrinkage are determined. An analytical relationship between the forces and deformations of the reinforced concrete sample with central reinforcement is derived for axial tension and compression, with allowance for strains and stresses in the reinforcement and concrete resulted from concrete shrinkage. The results of experimental studies are presented, including tension diagrams and diagrams of developing axial deformations with an increase in the load under the central loading of the reinforced elements. A methodology of accounting for stresses and deformations resulted from concrete shrinkage is developed. The applicability of the derived analytical relationships between stresses and deformations on the material diagrams to calculations of the reinforced concrete structures in the framework of the deformation model is estimated.

scholarly journals Microstructure and Mechanical Properties of Dissimilar Friction Welding Ti-6Al-4V Alloy to Nitinol

Metals ◽  
2021 ◽  
Vol 11 (1) ◽  
pp. 109
Author(s):  
Ateekh Ur Rehman ◽  
Nagumothu Kishore Babu ◽  
Mahesh Kumar Talari ◽  
Yusuf Siraj Usmani ◽  
Hisham Al-Khalefah
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Flow Stress ◽  
Intermetallic Compound ◽  
Ultimate Tensile Strength ◽  
Friction Welding ◽  
Welding Process ◽  
Weld Interface ◽  
Dissimilar Joints ◽  
Dissimilar Alloys

In the present study, a friction welding process was adopted to join dissimilar alloys of Ti-Al-4V to Nitinol. The effect of friction welding on the evolution of welded macro and microstructures and their hardnesses and tensile properties were studied and discussed in detail. The macrostructure of Ti-6Al-4V and Nitinol dissimilar joints revealed flash formation on the Ti-6Al-4V side due to a reduction in flow stress at high temperatures during friction welding. The optical microstructures revealed fine grains near the Ti-6Al-4V interface due to dynamic recrystallization and strain hardening effects. In contrast, the area nearer to the nitinol interface did not show any grain refinement. This study reveals that the formation of an intermetallic compound (Ti2Ni) at the weld interface resulted in poor ultimate tensile strength (UTS) and elongation values. All tensile specimens failed at the weld interface due to the formation of intermetallic compounds.

Modeling of Size Effects on the Flow Stress of Type 304 Stainless Steel and Application in Coining Process

2007 ◽  
Author(s):  
Gap-Yong Kim ◽  
Muammer Koc ◽  
Jun Ni
Keyword(s):  
Grain Size ◽  
Stainless Steel ◽  
Flow Stress ◽  
Size Effect ◽  
Size Effects ◽  
Specimen Size ◽  
304 Stainless Steel ◽  
Length Scales ◽  
Type 304 ◽  
Type 304 Stainless Steel

Application of microforming in various research areas has received much attention due to the increased demand for miniature metallic parts that require mass production. For the accurate analysis and design of microforming process, proper modeling of material behavior at the micro/meso-scale is necessary by considering the size effects. Two size effects are known to exist in metallic materials. One is the “grain size” effect, and the other is the “feature/specimen size” effect. This study investigated the “feature/specimen size” effect and introduced a scaling model which combined both feature/specimen and grain size effects. Predicted size effects were compared with experiments obtained from previous research and showed a very good agreement. The model was also applied to forming of micro-features by coining. A flow stress model for Type 304 stainless steel taking into consideration the effect of the grain and feature size was developed and implemented into a finite element simulation tool for an accurate numerical analysis. The scaling model offered a simple way to model the size effect down to length scales of a couple of grains and extended the use of continuum plasticity theories to micro/meso-length scales.

scholarly journals The Effect of Heat Treatment on the Microstructure and Mechanical Properties of the Novel Low-Cost Ti-3Al-5Mo-4Cr-2Zr-1Fe Alloy

Materials ◽  
2020 ◽  
Vol 13 (17) ◽  
pp. 3798
Author(s):  
Meng Sun ◽  
Dong Li ◽  
Yanhua Guo ◽  
Ying Wang ◽  
Yuecheng Dong ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Aging Time ◽  
Volume Fraction ◽  
Low Cost ◽  
Solution Treatment ◽  
Solution Temperature ◽  
The Novel ◽  
Α Phase ◽  
The Cost

In order to reduce the cost of titanium alloys, a novel low-cost Ti-3Al-5Mo-4Cr-2Zr-1Fe (Ti-35421) titanium alloy was developed. The influence of heat treatment on the microstructure characteristics and mechanical properties of the new alloy was investigated. The results showed that the microstructure of Ti-35421 alloy consists of a lamina primary α phase and a β phase after the solution treatment at the α + β region. After aging treatment, the secondary α phase precipitates in the β matrix. The precipitation of the secondary α phase is closely related to heat treatment parameters—the volume fraction and size of the secondary α phase increase when increasing the solution temperature or aging time. At the same solution temperature and aging time, the secondary α phase became coarser, and the fraction decreased with increasing aging temperature. When Ti-35421 alloy was solution-treated at the α + β region for 1 h with aging surpassing 8 h, the tensile strength, yield strength, elongation and reduction of the area were achieved in a range of 1172.7–1459.0 MPa, 1135.1–1355.5 MPa, 5.2–11.8%, and 7.5–32.5%, respectively. The novel low-cost Ti-35421 alloy maintains mechanical properties and reduces the cost of materials compared with Ti-3Al-5Mo-5V-4Cr-2Zr (Ti-B19) alloy.

scholarly journals Mechanical properties of wrought magnesium alloys

2021 ◽  
Author(s):  
Sanjida Begum
Keyword(s):  
Mechanical Properties ◽  
Strain Rate ◽  
Magnesium Alloys ◽  
Bauschinger Effect ◽  
Fatigue Crack Initiation ◽  
Hysteresis Loops ◽  
Cyclic Hardening ◽  
Strain Ratio ◽  
Strain Hardening Exponent ◽  
Lower Strain

Lightweight magnesium alloys are being increasingly used in automotive and other transportation industries to achieve energy efficiency. The objective of this thesis was to study the mechanical properties of two wrought alloys AZ31 and AM30. With increasing strain rate the yield strength and ultimate tensile strength increased and the strain hardening exponent decreased for AM30 and increased for AZ31. Both alloys exhibited stable cyclic characteristics at lower strain amplitudes and cyclic hardening characteristics at higher strain amplitudes. The Bauschinger effect was pronounced at higher strain amplitudes, resulting in asymmetric hysteresis loops in both alloys. The influence of strain ratio (Rs), strain rate, and initial straining direction on the cyclic deformation characteristics and fatigue life was evaluated. At low Rs, both alloys exhibited strong cyclic hardening, which decreased as Rs increased. Fatigue crack initiation was observed to occur from the specimen surface and crack propagation was basically characterized by striation-like features.

Constitutive Analysis of the High-Temperature Deformation Behavior of Single Phase α-Ti and α+β Ti-6Al-4V Alloy

2007 ◽  
Vol 539-543 ◽  
pp. 3607-3612 ◽  
Author(s):  
Jeoung Han Kim ◽  
Jong Taek Yeom ◽  
Nho Kwang Park ◽  
Chong Soo Lee
Keyword(s):  
High Temperature ◽  
Flow Stress ◽  
Deformation Behavior ◽  
Single Phase ◽  
Volume Fraction ◽  
High Temperature Deformation ◽  
Temperature Deformation ◽  
Β Phase ◽  
Α Phase ◽  
Self Consistent

The high-temperature deformation behavior of the single-phase α (Ti-7.0Al-1.5V) and α + β (Ti-6Al-4V) alloy were determined and compared within the framework of self-consistent scheme at various temperature ranges. For this purpose, isothermal hot compression tests were conducted at temperatures between 650°C ~ 950°C to determine the effect of α/β phase volume fraction on average flow stress under hot-working condition. The flow behavior of α phase was estimated from the compression test results of single-phase α alloy whose chemical composition is close to that of α phase of Ti-6Al-4V alloy. On the other hand, the flow stress of β phase in Ti-6Al-4V was predicted by using self-consistent method. The flow stress of α phase was higher than that of β phase above 750°C, while the β phase revealed higher flow stress than α phase at 650°C. Also, at temperature above 750°C, the predicted strain rate of β phase was higher than that of α phase. It was found that the relative strength between α and β phase significantly varied with temperature.

Influences of Solution Temperatures on Microstructure and Mechanical Properties of near α Titanium Alloy

2021 ◽  
Vol 1035 ◽  
pp. 89-95
Author(s):  
Chao Tan ◽  
Zi Yong Chen ◽  
Zhi Lei Xiang ◽  
Xiao Zhao Ma ◽  
Zi An Yang
Keyword(s):  
Mechanical Properties ◽  
Titanium Alloy ◽  
High Temperature ◽  
Room Temperature ◽  
Solution Temperature ◽  
Vacuum Induction Melting ◽  
Induction Melting ◽  
Β Phase ◽  
Α Phase ◽  
New Type

A new type of Ti-Al-Sn-Zr-Mo-Si series high temperature titanium alloy was prepared by a water-cooled copper crucible vacuum induction melting method, and its phase transition point was determined by differential thermal analysis to be Tβ = 1017 °C. The influences of solution temperature on the microstructures and mechanical properties of the as-forged high temperature titanium alloy were studied. XRD results illustrated that the phase composition of the alloy after different heat treatments was mainly α phase and β phase. The microstructures showed that with the increase of the solution temperature, the content of the primary α phase gradually reduced, the β transformation structure increased by degrees, then, the number and size of secondary α phase increased obviously. The tensile results at room temperature (RT) illustrated that as the solution temperature increased, the strength of the alloy gradually increased, and the plasticity decreased slightly. The results of tensile test at 650 °C illustrated that the strength of the alloy enhanced with the increase of solution temperature, the plasticity decreased first and then increased, when the solution temperature increased to 1000 °C, the alloy had the best comprehensive mechanical properties, the tensile strength reached 714.01 MPa and the elongation was 8.48 %. Based on the room temperature and high temperature properties of the alloy, the best heat treatment process is finally determined as: 1000 °C/1 h/AC+650 °C/6 h/AC.

scholarly journals Study on Grain Refinement Mechanisms and Mechanical Properties of bi-Modal Ti-55511 Titanium Alloy during Hot Rolling

Materials ◽  
2020 ◽  
Vol 13 (15) ◽  
pp. 3351 ◽  
Author(s):  
Wei Chen ◽  
Xiaoyong Zhang ◽  
YongCheng Lin ◽  
Kechao Zhou
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Scanning Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Hot Rolling ◽  
Shear Bands ◽  
High Ductility ◽  
Α Phase ◽  
Transmission Electron ◽  
Scanning Electron

Multi-pass hot rolling was performed on bi-modal Ti-55511 alloy with 50% rolling reduction at 700 °C. Mechanical properties were evaluated by tensile test, and microstructure evolution was characterized by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The results show that the Ti-55511 alloy with bi-modal microstructure exhibits good strength and high ductility (1102 MPa, 21.7%). Comparatively, after 50% hot rolling, an enhanced strength and decreased ductility were obtained. The refinement of α phases leads to the increased tensile strength, while the fragmentation of the equiaxed α phase results in a decreased ductility. The fragmentation process of equiaxed α phases followed the sequence of: elongation of α phases → formation of grooves and localized shear bands → the final fragmentation accomplished via deepening grooves.

scholarly journals Influence of the Mechanical Properties of Elastoplastic Materials on the Nanoindentation Loading Response

Materials ◽  
2020 ◽  
Vol 13 (21) ◽  
pp. 4842
Author(s):  
Huanping Yang ◽  
Wei Zhuang ◽  
Wenbin Yan ◽  
Yaomian Wang
Keyword(s):  
Mechanical Properties ◽  
Finite Element Method ◽  
Finite Element ◽  
The Other ◽  
Equivalent Model ◽  
Strain Hardening Exponent ◽  
Mechanical Parameters ◽  
The Finite Element Method ◽  
Fem Simulations ◽  
Elastoplastic Materials

The nanoindentation loading response of elastoplastic materials was simulated by the finite element method (FEM). The influence of the Young’s modulus E, yield stress σy, strain hardening exponent n and Poisson’s ratio ν on the loading response was investigated. Based on an equivalent model, an equation with physical meaning was proposed to quantitatively describe the influence. The calculations agree well with the FEM simulations and experimental results in literature. Comparisons with the predictions using equations in the literature also show the reliability of the proposed equation. The investigations show that the loading curvature C increases with increasing E, σy, n and ν. The increase rates of C with E, σy, n and ν are different for their different influences on the flow stress after yielding. It is also found that the influence of one of the four mechanical parameters on C can be affected by the other mechanical parameters.

Sign in / Sign up

Export Citation Format

Share Document