scholarly journals Effect of Nanoparticle Content on the Microstructural and Mechanical Properties of Forged and Heat-Treated TiC/2219 Nanocomposites

Metals ◽  
2019 ◽  
Vol 9 (9) ◽  
pp. 982 ◽  
Author(s):  
Yilong Yang ◽  
Ripeng Jiang ◽  
Xiaoqian Li ◽  
Yun Zhang ◽  
Ruiqing Li
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Aluminum Matrix ◽  
Aging Treatment ◽  
Aluminum Matrix Composites ◽  
Electron Backscattered Diffraction ◽  
Scanning Calorimetry ◽  
Multidirectional Forging ◽  
Nanoparticle Content ◽  
Tic Nanoparticle

In this study, castings of TiC nanoparticle reinforced 2219 aluminum matrix composites with different TiC nanoparticle contents (0, 0.5, 0.9, 1.3, and 1.7 wt.%) prepared using an ultrasound-assisted stirring technology were deformed by multidirectional forging at 510 °C followed by T6 aging treatment. The microstructural evolution and mechanical properties of the 2219 alloy and its composites were investigated and compared. Optical microscopy and scanning electron microscopy revealed that the composite with 0.9 wt.% TiC nanoparticle content possessed finer grains and the lowest amount of Al2Cu phases. The electron backscattered diffraction (EBSD) was used to characterize the sub-grains. The precipitation microstructures of the 2219 alloy and composites with different nanoparticle contents were characterized by differential scanning calorimetry and transmission electron microscopy. It was found that 0.9 wt.% TiC/2219 nanocomposites contained the highest amount of θ″ and θ′ phases with shorter lengths. This might imply that the nanoparticles uniformly dispersed in the matrix could facilitate the precipitation of θ″ and θ′ phases during aging. Thus, the 0.9 wt.% TiC/2219 nanocomposite showed the best mechanical properties. The ultimate tensile strength, yield strength, and elongation of the 0.9 wt.% TiC/2219 nanocomposite increased by 24.2, 46.1, and 37.2%, respectively, compared to those of the 2219 alloy.

scholarly journals Effect of T6 Heat Treatment on Microstructure and Hardness of Nanosized Al2O3 Reinforced 7075 Aluminum Matrix Composites

Metals ◽  
2019 ◽  
Vol 9 (1) ◽  
pp. 44 ◽  
Author(s):  
Peng-Xiang Zhang ◽  
Hong Yan ◽  
Wei Liu ◽  
Xiu-Liang Zou ◽  
Bin-Bing Tang
Keyword(s):  
Electron Microscopy ◽  
Heat Treatment ◽  
Solution Treatment ◽  
Aluminum Matrix ◽  
Aging Treatment ◽  
Aluminum Matrix Composites ◽  
Matrix Composites ◽  
X Ray ◽  
T6 Heat Treatment ◽  
The Matrix

In this study, 7075 aluminum matrix composites reinforced with 1.5 wt.% nanosized Al2O3 were fabricated by ultrasonic vibration. The effect of T6 heat treatment on both microstructure and hardness of nanosized Al2O3 reinforced 7075 (Al2O3np/7075) composites were studied via scanning electron microscopy, energy dispersive X-ray spectrometry, X-ray diffraction, transmission electron microscopy, and hardness tests. The Mg(Zn,Cu,Al)2 phases gradually dissolved into the matrix under solution treatment at 480 °C for 5 h. However, the morphology and size of Al7Cu2Fe phases remained unchanged due to their high melting points. Furthermore, the slenderness strips MgZn2 phases precipitated under aging treatment at 120 °C for 24 h. Compared to as-cast composites, the hardness of the sample under T6 heat treatment was increased ~52%. The strengthening mechanisms underlying the achieved hardness of composites are revealed.

scholarly journals Evolution of Microstructure and Mechanical Properties of LM25–HEA Composite Processed through Stir Casting with a Bottom Pouring System

Materials ◽  
2021 ◽  
Vol 15 (1) ◽  
pp. 230
Author(s):  
Mekala Chinababu ◽  
Nandivelegu Naga Krishna ◽  
Katakam Sivaprasad ◽  
Konda Gokuldoss Prashanth ◽  
Eluri Bhaskara Rao
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Tensile Strength ◽  
Aluminum Matrix ◽  
Stir Casting ◽  
Significant Loss ◽  
Aluminum Matrix Composites ◽  
High Entropy Alloy ◽  
High Entropy ◽  
The Matrix

Aluminum matrix composites reinforced by CoCrFeMnNi high entropy alloy (HEA) particulates were fabricated using the stir casting process. The as-cast specimens were investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), and transmission electron microscopy (TEM). The results indicated that flake-like silicon particles and HEA particles were distributed uniformly in the aluminum matrix. TEM micrographs revealed the presence of both the matrix and reinforcement phases, and no intermetallic phases were formed at the interface of the matrix and reinforcement phases. The mechanical properties of hardness and tensile strength increased with an increase in the HEA content. The Al 6063–5 wt.% HEA composite had a ultimate tensile strength (UTS) of approximately 197 MPa with a reasonable ductility (around 4.05%). The LM25–5 wt.% HEA composite had a UTS of approximately 195 Mpa. However, the percent elongation decreased to roughly 3.80%. When the reinforcement content increased to 10 wt.% in the LM25 composite, the UTS reached 210 MPpa, and the elongation was confined to roughly 3.40%. The fracture morphology changed from dimple structures to cleavage planes on the fracture surface with HEA weight percentage enhancement. The LM25 alloy reinforced with HEA particles showed enhanced mechanical strength without a significant loss of ductility; this composite may find application in marine and ship building industries.

Effect of Titanium Carbide Particles on Mechanical Properties of Aluminum Matrix Composites

2017 ◽  
Vol 5 (2) ◽  
pp. 20-30
Author(s):  
Zaman Khalil Ibrahim
Keyword(s):  
Mechanical Properties ◽  
Titanium Carbide ◽  
Compression Strength ◽  
Volume Fraction ◽  
Aluminum Matrix ◽  
Aluminum Matrix Composites ◽  
Matrix Composites ◽  
Powder Metallurgy Technique ◽  
Carbide Particles ◽  
Properties Of Composites

In this research aluminum matrix composites (AMCs) was reinforced by titanium carbide (TiC) particles and was produced. Powder metallurgy technique (PM) has been used to fabricate AMCs reinforced with various amounts (0%, 4%, 8%, 12%, 16% and 20% volume fraction) of TiC particles to study the effect of different volume fractions on mechanical properties of the Al-TiC composites. Measurements of compression strength and hardness showed that mechanical properties of composites increased with an increase in volume fraction of TiC Particles. Al-20 % vol. TiC composites exhibited the best properties with hardness value (97HRB) and compression strength value (275Mpa).

scholarly journals Effects of Aging under Stress on Mechanical Properties and Microstructure of EN AW 7075 Alloy

Metals ◽  
2021 ◽  
Vol 11 (7) ◽  
pp. 1142
Author(s):  
S. V. Sajadifar ◽  
P. Krooß ◽  
H. Fröck ◽  
B. Milkereit ◽  
O. Kessler ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Screening Tool ◽  
Precipitation Kinetics ◽  
Scanning Calorimetry ◽  
Aging Precipitation ◽  
Precipitation Processes ◽  
External Stresses ◽  
7075 Alloy ◽  
Effects Of Aging

In the present study, microstructural and mechanical properties of EN AW 7075 following stress-aging were assessed. For this purpose, properties of stress-aged samples were compared with values obtained for conventionally aged counterparts. It is revealed that the strength and hardness of EN AW 7075 can be increased by the presence of external stresses during aging. Precipitation kinetics were found to be accelerated. The effects of conventional and stress-aging on the microstructure were analyzed using synergetic techniques: the differently aged samples were probed by differential scanning calorimetry (DSC) in order to characterize the precipitation processes. DSC was found to be an excellent screening tool for the analysis of precipitation processes during aging of this alloy with and without the presence of external stresses. Furthermore, using electron microscopy it was revealed that an improvement in mechanical properties can be correlated to changes in the morphologies and sizes of precipitates formed.

The Effect of Aging Heat Treatment on the Microstructure and Mechanical Properties of 10Cr20Ni25Mo1.5NbN Austenitic Steel

2016 ◽  
Vol 35 (1) ◽  
pp. 1-7 ◽  
Author(s):  
Zhiyuan Liang ◽  
Wanhua Sha ◽  
Qinxin Zhao ◽  
Chongbin Wang ◽  
Jianyong Wang ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Heat Treatment ◽  
Austenitic Steel ◽  
Treatment Time ◽  
Aging Treatment ◽  
Secondary Phases ◽  
Aging Heat Treatment ◽  
Microstructure And Mechanical Properties ◽  
The Impact

AbstractThe effect of aging heat treatment on the microstructure and mechanical properties of 10Cr20Ni25Mo1.5NbN austenitic steel was investigated in this article. The microstructure was characterized by scanning electron microscopy, energy dispersive spectrometry and transmission electron microscopy. Results show that the microstructure of 10Cr20Ni25Mo1.5NbN austenitic is composed of austenite. This steel was strengthened by precipitates of secondary phases that were mainly M23C6 carbides and NbCrN nitrides. As aging treatment time increased, the tensile strength first rose (0–3,000 h) and then fell (3,000–5,000 h) due to the decrease of high density of dislocations. The impact absorbed energy decreased sharply, causing the sulfides to precipitate at the grain boundary. Therefore, the content of sulfur should be strictly controlled in the steelmaking process.

Research on compatibility and surface of high impact bio-based polyamide

2021 ◽  
pp. 095400832110055
Author(s):  
Yang Wang ◽  
Yuhui Zhang ◽  
Yuhan Xu ◽  
Xiucai Liu ◽  
Weihong Guo
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Scanning Electron Microscopy ◽  
Differential Scanning Calorimetry ◽  
Crystallization Behavior ◽  
High Impact ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Scanning Electron

The super-tough bio-based nylon was prepared by melt extrusion. In order to improve the compatibility between bio-based nylon and elastomer, the elastomer POE was grafted with maleic anhydride. Scanning Electron Microscopy (SEM) and Thermogravimetric Analysis (TGA) were used to study the compatibility and micro-distribution between super-tough bio-based nylon and toughened elastomers. The results of mechanical strength experiments show that the 20% content of POE-g-MAH has the best toughening effect. After toughening, the toughness of the super-tough nylon was significantly improved. The notched impact strength was 88 kJ/m2 increasing by 1700%, which was in line with the industrial super-tough nylon. X-ray Diffraction (XRD) and Differential Scanning Calorimetry (DSC) were used to study the crystallization behavior of bio-based PA56, and the effect of bio-based PA56 with high crystallinity on mechanical properties was analyzed from the microstructure.

Sign in / Sign up

Export Citation Format

Share Document