scholarly journals High-Performance Resistive Switching in Solution-Derived IGZO:N Memristors by Microwave-Assisted Nitridation

Nanomaterials ◽  
2021 ◽  
Vol 11 (5) ◽  
pp. 1081
Author(s):  
Shin-Yi Min ◽  
Won-Ju Cho
Keyword(s):  
Resistive Switching ◽  
Photoelectron Spectroscopy ◽  
High Performance ◽  
Electric Pulse ◽  
Chemical Species ◽  
Optical Absorption Coefficient ◽  
Microwave Assisted ◽  
Synthesis Strategy ◽  
Metal Insulator Metal ◽  
Switching Characteristics

In this study, we implemented a high-performance two-terminal memristor device with a metal/insulator/metal (MIM) structure using a solution-derived In-Ga-Zn-Oxide (IGZO)-based nanocomposite as a resistive switching (RS) layer. In order to secure stable memristive switching characteristics, IGZO:N nanocomposites were synthesized through the microwave-assisted nitridation of solution-derived IGZO thin films, and the resulting improvement in synaptic characteristics was systematically evaluated. The microwave-assisted nitridation of solution-derived IGZO films was clearly demonstrated by chemical etching, optical absorption coefficient analysis, and X-ray photoelectron spectroscopy. Two types of memristor devices were prepared using an IGZO or an IGZO:N nanocomposite film as an RS layer. As a result, the IGZO:N memristors showed excellent endurance and resistance distribution in the 103 repeated cycling tests, while the IGZO memristors showed poor characteristics. Furthermore, in terms of electrical synaptic operation, the IGZO:N memristors possessed a highly stable nonvolatile multi-level resistance controllability and yielded better electric pulse-induced conductance modulation in 5 × 102 stimulation pulses. These findings demonstrate that the microwave annealing process is an effective synthesis strategy for the incorporation of chemical species into the nanocomposite framework, and that the microwave-assisted nitridation improves the memristive switching characteristics in the oxide-based RS layer.

scholarly journals Multi-level characteristics of TiOx transparent non-volatile resistive switching device by embedding SiO2 nanoparticles

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Sera Kwon ◽  
Min-Jung Kim ◽  
Kwun-Bum Chung
Keyword(s):  
Resistive Switching ◽  
High Performance ◽  
Sio2 Nanoparticles ◽  
Visible Range ◽  
Resistive State ◽  
Switching Device ◽  
Structural Density ◽  
Multi Level ◽  
Switching Characteristics ◽  
Switching Devices

AbstractTiOx-based resistive switching devices have recently attracted attention as a promising candidate for next-generation non-volatile memory devices. A number of studies have attempted to increase the structural density of resistive switching devices. The fabrication of a multi-level switching device is a feasible method for increasing the density of the memory cell. Herein, we attempt to obtain a non-volatile multi-level switching memory device that is highly transparent by embedding SiO2 nanoparticles (NPs) into the TiOx matrix (TiOx@SiO2 NPs). The fully transparent resistive switching device is fabricated with an ITO/TiOx@SiO2 NPs/ITO structure on glass substrate, and it shows transmittance over 95% in the visible range. The TiOx@SiO2 NPs device shows outstanding switching characteristics, such as a high on/off ratio, long retention time, good endurance, and distinguishable multi-level switching. To understand multi-level switching characteristics by adjusting the set voltages, we analyze the switching mechanism in each resistive state. This method represents a promising approach for high-performance non-volatile multi-level memory applications.

scholarly journals Resistive Switching Characteristics of Li-Doped ZnO Thin Films Based on Magnetron Sputtering

Materials ◽  
2019 ◽  
Vol 12 (8) ◽  
pp. 1282 ◽  
Author(s):  
Zhao ◽  
Li ◽  
Ai ◽  
Wen
Keyword(s):  
Thin Films ◽  
Magnetron Sputtering ◽  
Resistive Switching ◽  
Photoelectron Spectroscopy ◽  
Lattice Structure ◽  
Zno Thin Films ◽  
Bipolar Resistive Switching ◽  
X Ray ◽  
Doped Zno ◽  
Switching Characteristics

A kind of devices Pt/Ag/ZnO:Li/Pt/Ti with high resistive switching behaviors were prepared on a SiO2/Si substrate by using magnetron sputtering method and mask technology, composed of a bottom electrode (BE) of Pt/Ti, a resistive switching layer of ZnO:Li thin film and a top electrode (TE) of Pt/Ag. To determine the crystal lattice structure and the Li-doped concentration in the resulted ZnO thin films, X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS) tests were carried out. Resistive switching behaviors of the devices with different thicknesses of Li-doped ZnO thin films were studied at different set and reset voltages based on analog and digital resistive switching characteristics. At room temperature, the fabricated devices represent stable bipolar resistive switching behaviors with a low set voltage, a high switching current ratio and a long retention up to 104 s. In addition, the device can sustain an excellent endurance more than 103 cycles at an applied pulse voltage. The mechanism on how the thicknesses of the Li-doped ZnO thin films affect the resistive switching behaviors was investigated by installing conduction mechanism models. This study provides a new strategy for fabricating the resistive random access memory (ReRAM) device used in practice.

WOx resistive memory elements for scaled Flash memories

2011 ◽  
Vol 1337 ◽  
Author(s):  
S. Gorji Ghalamestani ◽  
L. Goux ◽  
D.E. Díaz-Droguett ◽  
D. Wouters ◽  
J. G. Lisoni
Keyword(s):  
Resistive Switching ◽  
Photoelectron Spectroscopy ◽  
Time Windows ◽  
Electrical Measurement ◽  
Thin Layers ◽  
Switching Behavior ◽  
Elastic Recoil ◽  
X Ray ◽  
Bipolar Switching ◽  
Switching Characteristics

ABSTRACTWe investigated the resistive switching behavior of WOx films. WOx was obtained from the thermal oxidation of W thin layers. The parameters under investigation were the influence of the temperature (450-500 °C) and time (30-220 s) used to obtain the WOx on the resistive switching characteristics of Si\W\WOx\Metal_electrode ReRAM cells. The metal top electrodes (TE) tested were Pt, Ni, Cu and Au. The elemental composition and microstructure of the samples were characterized by means of elastic recoil detection analysis (ERD), X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM), X-ray diffraction (XRD) and X-ray reflectivity (XRR).Electrical measurement of the WOx-based memory elements revealed bipolar and unipolar switching and this depended upon the oxidation conditions and TE selected. Indeed, switching events were observed in WOx samples obtained either at 450 °C or 500 °C in time windows of 180-200 s and 30-60 s, respectively. Pt and Au TE promoted bipolar switching while unipolar behavior was observed with Ni TE only; no switching events were observed with Cu TE. Good switching characteristics seems not related to the overall thickness, crystallinity and composition of the oxide, but on the W6+/W5+ ratio present on the WOx surface, surface in contact with the TE material. Interestingly, W6+/W5+ ratio can be tuned through the oxidation conditions, showing a path for optimizing the properties of the WOx-based ReRAM cells.

scholarly journals Understanding the Resistive Switching Phenomena of Stacked Al/Al2O3/Al Thin Films from the Dynamics of Conductive Filaments

Complexity ◽  
2017 ◽  
Vol 2017 ◽  
pp. 1-10 ◽  
Author(s):  
Joel Molina-Reyes ◽  
Luis Hernandez-Martinez
Keyword(s):  
Resistive Switching ◽  
Atomic Layer ◽  
Memory Device ◽  
Switching Behavior ◽  
Processing Temperature ◽  
Force Microscopy ◽  
Atomic Force ◽  
Layer Deposition ◽  
Metal Insulator Metal ◽  
Switching Characteristics

We present the resistive switching characteristics of Metal-Insulator-Metal (MIM) devices based on amorphous Al2O3 which is deposited by Atomic Layer Deposition (ALD). A maximum processing temperature for this memory device is 300°C, making it ideal for Back-End-of-Line (BEOL) processing. Although some variations in the forming, set, and reset voltages (VFORM, VSET, and VRESET) are obtained for many of the measured MIM devices (mainly due to roughness variations of the MIM interfaces as observed after atomic-force microscopy analysis), the memristor effect has been obtained after cyclic I-V measurements. These resistive transitions in the metal oxide occur for both bipolar and unipolar conditions, while the IOFF/ION ratio is around 4–6 orders of magnitude and is formed at gate voltages of Vg<4 V. In unipolar mode, a gradual reduction in VSET is observed and is related to combined (a) incomplete dissolution of conductive filaments (made of oxygen vacancies and metal ions) which leaves some residuals and (b) thickening of chemically reduced Al2O3 during localized Joule heating. This is important because, by analyzing the macroscopic resistive switching behavior of this MIM structure, we could indirectly relate it to microscopic and/or nanoscopic phenomena responsible for the physical mechanism upon which most of these devices operate.

Multilevel characteristics of TiOx transparent non-volatile resistive switching device by embedding SiO2 nanoparticles

2021 ◽  
Author(s):  
Sera Kwon ◽  
Min-Jung Kim ◽  
Kwun-Bum Chung
Keyword(s):  
Resistive Switching ◽  
High Performance ◽  
Sio2 Nanoparticles ◽  
Visible Range ◽  
Resistive State ◽  
Switching Device ◽  
Structural Density ◽  
Multi Level ◽  
Switching Characteristics ◽  
Switching Devices

Abstract TiOx-bsed resistive switching devices have recently attracted attention as a promising candidate for next-generation non-volatile memory devices. A number of studies have attempted to increase the structural density of resistive switching devices. The fabrication of a multi-level switching device is a feasible method for increasing the density of the memory cell. Herein, we attempt to obtain a non-volatile multi-level switching memory device that is highly transparent by embedding SiO2 nanoparticles (NPs) into the TiOx matrix (TiOx@SiO2 NPs). The fully transparent resistive switching device is fabricated with an ITO/TiOx@SiO2 NPs/ITO structure on glass substrate, and it shows transmittance over 95 % in the visible range. The TiOx@SiO2 NPs device shows outstanding switching characteristics, such as a high on/off ratio, long retention time, good endurance, and distinguishable multi-level switching. To understand multi-level switching characteristics by adjusting the set voltages, we analyze the switching mechanism in each resistive state. This method represents a promising approach for high-performance non-volatile multi-level memory applications.

scholarly journals Switching Characteristics and Mechanism Using Al2O3 Interfacial Layer in Al/Cu/GdOx/Al2O3/TiN Memristor

Electronics ◽  
2020 ◽  
Vol 9 (9) ◽  
pp. 1466
Author(s):  
Chiao-Fan Chiu ◽  
Sreekanth Ginnaram ◽  
Asim Senapati ◽  
Yi-Pin Chen ◽  
Siddheswar Maikap
Keyword(s):  
Resistive Switching ◽  
Photoelectron Spectroscopy ◽  
Interfacial Layer ◽  
Stable State ◽  
Schematic Model ◽  
Bipolar Resistive Switching ◽  
Al2o3 Layer ◽  
X Ray ◽  
Resistance State ◽  
Switching Characteristics

Resistive switching characteristics by using the Al2O3 interfacial layer in an Al/Cu/GdOx/Al2O3/TiN memristor have been enhanced as compared to the Al/Cu/GdOx/TiN structure owing to the insertion of Al2O3 layer for the first time. Polycrystalline grain, chemical composition, and surface roughness of defective GdOx film have been investigated by transmission electron microscope (TEM), X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD), and atomic force microscopy (AFM). For bipolar resistive switching (BRS) characteristics, the conduction mechanism of high resistance state (HRS) is a space-charge limited current for the Al/Cu/GdOx/TiN device while the Al/Cu/GdOx/Al2O3/TiN device shows Schottky emission. However, both devices show Ohmic at a low resistance state (LRS). After the device has been SET, the Cu filament evidences by both TEM and elemental mapping. Oxygen-rich at the Cu/GdOx interface and Al2O3 layer are confirmed by energy dispersive X-ray spectroscopy (EDS) line profile. The Al/Cu/GdOx/Al2O3/TiN memristor has lower RESET current, higher speed operation of 100 ns, long read pulse endurance of >109 cycles, good data retention, and the memristor with a large resistance ratio of >105 is operated at a low current of 1.5 µA. The complementary resistive switching (CRS) characteristics of the Al/Cu/GdOx/Al2O3/TiN memristor show also a low current operation as compared to the Al/Cu/GdOx/TiN device (300 µA vs. 3.1 mA). The transport mechanism is the Cu ion migration and it shows Ohmic at low field and hopping at high field regions. A larger hopping distance of 1.82 nm at the Cu/GdOx interface is obtained as compared to a hopping distance of 1.14 nm in the Al2O3 layer owing to a larger Cu filament length at the Cu/GdOx interface than the Al2O3 layer. Similarly, the CRS mechanism is explained by using the schematic model. The CRS characteristics show a stable state with long endurance of >1000 cycles at a pulse width of 1 µs owing to the insertion of Al2O3 interfacial layer in the Al/Cu/GdOx/Al2O3/TiN structure.

scholarly journals Chemical Nature of Electrode and the Switching Response of RF-Sputtered NbOx Films

Nanomaterials ◽  
2020 ◽  
Vol 10 (11) ◽  
pp. 2164
Author(s):  
Jamal Aziz ◽  
Honggyun Kim ◽  
Shania Rehman ◽  
Muhammad Farooq Khan ◽  
Deok-kee Kim
Keyword(s):  
Resistive Switching ◽  
Photoelectron Spectroscopy ◽  
Dominant Role ◽  
Interface Layer ◽  
Spectroscopy Analysis ◽  
X Ray ◽  
Inert Electrode ◽  
Switching Characteristics ◽  
Different Characteristics

In this study, the dominant role of the top electrode is presented for Nb2O5-based devices to demonstrate either the resistive switching or threshold characteristics. These Nb2O5-based devices may exhibit different characteristics depending on the selection of electrode. The use of the inert electrode (Au) initiates resistive switching characteristics in the Au/Nb2O5/Pt device. Alternatively, threshold characteristics are induced by using reactive electrodes (W and Nb). The X-ray photoelectron spectroscopy analysis confirms the presence of oxide layers of WOy and NbOx at interfaces for W and Nb as top electrodes. However, no interface layer between the top electrode and active layer is detected in X-ray photoelectron spectroscopy for Au as the top electrode. Moreover, the dominant phase is Nb2O5 for Au and NbO2 for W and Nb. The threshold characteristics are attributed to the reduction of Nb2O5 phase to NbO2 due to the interfacial oxide layer formation between the reactive top electrode and Nb2O5. Additionally, reliability tests for both resistive switching and threshold characteristics are also performed to confirm switching stabilities.

Sign in / Sign up

Export Citation Format

Share Document