scholarly journals Effect of Cinnamon Extraction Oil (CEO) for Algae Biofilm Shelf-Life Prolongation

Polymers ◽  
2018 ◽  
Vol 11 (1) ◽  
pp. 4 ◽  
Author(s):  
Maizatulnisa Othman ◽  
Haziq Rashid ◽  
Nur Jamal ◽  
Sharifah Shaharuddin ◽  
Sarina Sulaiman ◽  
...  
Keyword(s):  
Tensile Strength ◽  
Shelf Life ◽  
Moisture Absorption ◽  
Morphological Structure ◽  
Strength Properties ◽  
Casting Technique ◽  
Swelling Rate ◽  
Solution Casting Technique ◽  
Algae Biofilm ◽  
Life Prolongation

This study was conducted to improve the life-span of the biofilm produced from algae by evaluating the decomposition rate with the effect of cinnamon extraction oil (CEO). The biofilm was fabricated using the solution casting technique. The soil burying analysis demonstrated low moisture absorption of the biofilm, thus decelerating the degradation due to low swelling rate and micro-organism activity, prolonging the shelf-life of the biofilm. Hence, the addition of CEO also affects the strength properties of the biofilm. The maximum tensile strength was achieved with the addition of 5% CEO, which indicated a good intermolecular interaction between the biopolymer (algae) and cinnamon molecules. The tensile strength, which was measured at 4.80 MPa, correlated with the morphological structure. The latter was performed using SEM, where the surface showed the absence of a separating phase between the biofilm and cinnamon blend. This was evidenced by FTIR analysis, which confirmed the occurrence of no chemical reaction between the biofilm and CEO during processing. The prolongation shelf-life rate of biofilm with good tensile properties are achievable with the addition of 5% of CEO.

scholarly journals Properties of Biocomposite Film Based on Whey Protein Isolate Filled with Nanocrystalline Cellulose from Pineapple Crown Leaf

Polymers ◽  
2021 ◽  
Vol 13 (24) ◽  
pp. 4278
Author(s):  
Fitriani Fitriani ◽  
Sri Aprilia ◽  
Nasrul Arahman ◽  
Muhammad Roil Bilad ◽  
Hazwani Suhaimi ◽  
...  
Keyword(s):  
Tensile Strength ◽  
Whey Protein ◽  
Food Packaging ◽  
Water Solubility ◽  
Moisture Absorption ◽  
Principal Component ◽  
Whey Protein Isolate ◽  
Protein Isolate ◽  
Nanocrystalline Cellulose ◽  
Casting Technique

Among the main bio-based polymer for food packaging materials, whey protein isolate (WPI) is one of the biopolymers that have excellent film-forming properties and are environmentally friendly. This study was performed to analyse the effect of various concentrations of bio-based nanocrystalline cellulose (NCC) extracted from pineapple crown leaf (PCL) on the properties of whey protein isolate (WPI) films using the solution casting technique. Six WPI films were fabricated with different loadings of NCC from 0 to 10 % w/v. The resulting films were characterised based on their mechanical, physical, chemical, and thermal properties. The results show that NCC loadings increased the thickness of the resulting films. The transparency of the films decreased at higher NCC loadings. The moisture content and moisture absorption of the films decreased with the presence of the NCC, being lower at higher NCC loadings. The water solubility of the films decreased from 92.2% for the pure WPI to 65.5% for the one containing 10 % w/v of NCC. The tensile strength of the films peaked at 7% NCC loading with the value of 5.1 MPa. Conversely, the trend of the elongation at break data was the opposite of the tensile strength. Moreover, the addition of NCC produced a slight effect of NCC in FTIR spectra of the WPI films using principal component analysis. NCC loading enhanced the thermal stability of the WPI films, as shown by an increase in the glass transition temperature at higher NCC loadings. Moreover, the morphology of the films turned rougher and more heterogeneous with small particle aggregates in the presence of the NCC. Overall, the addition of NCC enhanced the water barrier and mechanical properties of the WPI films by incorporating the PCL-based NCC as the filler.

Increased dryness after pressing and wet web strength by utilizing foam application technology

TAPPI Journal ◽  
2016 ◽  
Vol 15 (11) ◽  
pp. 731-738 ◽  
Author(s):  
KARITA KINNUNEN-RAUDASKOSKI ◽  
KRISTIAN SALMINEN ◽  
JANI LEHMONEN ◽  
TUOMO HJELT
Keyword(s):  
Tensile Strength ◽  
Guar Gum ◽  
Paper Industry ◽  
Reference Sample ◽  
Strength Properties ◽  
Cellulose Microfibrils ◽  
Application Technology ◽  
Ethylene Vinyl Alcohol ◽  
Wet Pressing ◽  
Web Strength

Production cost savings by lowering basis weight has been a trend in papermaking. The strategy has been to decrease the amount of softwood kraft pulp and increase use of fillers and recycled fibers. These changes have a tendency to lower strength properties of both the wet and dry web. To compensate for the strength loss in the paper, a greater quantity of strength additives is often required, either dosed at the wet end or applied to the wet web by spray. In this pilot-scale study, it was shown how strength additives can be effectively applied with foam-based application technology. The technology can simultaneously increase dryness after wet pressing and enhance dry and wet web strength properties. Foam application of polyvinyl alcohol (PVA), ethylene vinyl alcohol (EVOH), carboxymethyl cellulose (CMC), guar gum, starch, and cellulose microfibrils (CMF) increased web dryness after wet pressing up to 5.2%-units compared to the reference sample. The enhanced dewatering with starch, guar gum, and CMF was detected with a bulk increase. Additionally, a significant increase in z-directional tensile strength of dry web and and in-plane tensile strength properties of wet web was obtained. Based on the results, foam application technology can be a very useful technology for several applications in the paper industry.

A Bottom-Up Approach to Solution-Processed, Atomically Precise Graphitic Cylinders on Surfaces

2018 ◽  
Author(s):  
Erik Leonhardt ◽  
Jeff M. Van Raden ◽  
David Miller ◽  
Lev N. Zakharov ◽  
Benjamin Aleman ◽  
...  
Keyword(s):  
Self Assembly ◽  
Carbon Nanostructures ◽  
Carbon Nanomaterials ◽  
Circle Packing ◽  
Pyrolytic Graphite ◽  
Building Blocks ◽  
Bottom Up ◽  
Casting Technique ◽  
New Class ◽  
Solution Casting Technique

Extended carbon nanostructures, such as carbon nanotubes (CNTs), exhibit remarkable properties but are difficult to synthesize uniformly. Herein, we present a new class of carbon nanomaterials constructed via the bottom-up self-assembly of cylindrical, atomically-precise small molecules. Guided by supramolecular design principles and circle packing theory, we have designed and synthesized a fluorinated nanohoop that, in the solid-state, self-assembles into nanotube-like arrays with channel diameters of precisely 1.63 nm. A mild solution-casting technique is then used to construct vertical “forests” of these arrays on a highly-ordered pyrolytic graphite (HOPG) surface through epitaxial growth. Furthermore, we show that a basic property of nanohoops, fluorescence, is readily transferred to the bulk phase, implying that the properties of these materials can be directly altered via precise functionalization of their nanohoop building blocks. The strategy presented is expected to have broader applications in the development of new graphitic nanomaterials with π-rich cavities reminiscent of CNTs.

scholarly journals Evaluation of the Impact of Organic Fillers on Selected Properties of Organosilicon Polymer

Polymers ◽  
2021 ◽  
Vol 13 (7) ◽  
pp. 1103
Author(s):  
Sara Sarraj ◽  
Małgorzata Szymiczek ◽  
Tomasz Machoczek ◽  
Maciej Mrówka
Keyword(s):  
Tensile Strength ◽  
Natural Fiber ◽  
Accelerated Aging ◽  
Strength Properties ◽  
Visual Observation ◽  
Walnut Shell ◽  
Pistachio Shell ◽  
Thermoplastic Matrix ◽  
Static Tensile ◽  
The Impact

Eco-friendly composites are proposed to substitute commonly available polymers. Currently, wood–plastic composites and natural fiber-reinforced composites are gaining growing recognition in the industry, being mostly on the thermoplastic matrix. However, little data are available about the possibility of producing biocomposites on a silicone matrix. This study focused on assessing selected organic fillers’ impact (ground coffee waste (GCW), walnut shell (WS), brewers’ spent grains (BSG), pistachio shell (PS), and chestnut (CH)) on the physicochemical and mechanical properties of silicone-based materials. Density, hardness, rebound resilience, and static tensile strength of the obtained composites were tested, as well as the effect of accelerated aging under artificial seawater conditions. The results revealed changes in the material’s properties (minimal density changes, hardness variation, overall decreasing resilience, and decreased tensile strength properties). The aging test revealed certain bioactivities of the obtained composites. The degree of material degradation was assessed on the basis of the strength characteristics and visual observation. The investigation carried out indicated the impact of the filler’s type, chemical composition, and grain size on the obtained materials’ properties and shed light on the possibility of acquiring ecological silicone-based materials.

Mechanical characterization of LM25 alloy matrix composite reinforced with boron carbide

2021 ◽  
pp. 002199832110055
Author(s):  
Zeeshan Ahmad ◽  
Sabah Khan
Keyword(s):  
Tensile Strength ◽  
Boron Carbide ◽  
Mechanical Characterization ◽  
Stir Casting ◽  
Surface Mapping ◽  
Alloy Matrix ◽  
Casting Technique ◽  
The Matrix ◽  
Carbide Particles

Alumnium alloy LM 25 based composites reinforced with boron carbide at different weight fractions of 4%, 8%, and 12% were fabricated by stir casting technique. The microstructures and morphology of the fabricated composites were studied by scanning electron microscopy and energy dispersive spectroscopy. Elemental mapping of all fabricated composites were done to demonstrate the elements present in the matrix and fabricated composites. The results of microstructural analyses reveal homogenous dispersion of reinforcement particles in the matrix with some little amount of clustering found in composites reinforced with 12% wt. of boron carbide. The mechanical characterization is done for both alloy LM 25 and all fabricated composites based on hardness and tensile strength. The hardness increased from 13.6% to 21.31% and tensile strength 6.4% to 22.8% as reinforcement percentage of boron carbide particles increased from 0% to 12% wt. A fractured surface mapping was also done for all composites.

scholarly journals Tannic-Acid-Cross-Linked and TiO2-Nanoparticle-Reinforced Chitosan-Based Nanocomposite Film

Polymers ◽  
2021 ◽  
Vol 13 (2) ◽  
pp. 228
Author(s):  
Swarup Roy ◽  
Lindong Zhai ◽  
Hyun Chan Kim ◽  
Duc Hoa Pham ◽  
Hussein Alrobei ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tannic Acid ◽  
Nanocomposite Film ◽  
Food Packaging ◽  
Titanium Dioxide Nanoparticles ◽  
Casting Technique ◽  
Active Food Packaging ◽  
Reinforcing Agent ◽  
Solution Casting Technique ◽  
Cross Linker

A chitosan-based nanocomposite film with tannic acid (TA) as a cross-linker and titanium dioxide nanoparticles (TiO2) as a reinforcing agent was developed with a solution casting technique. TA and TiO2 are biocompatible with chitosan, and this paper studied the synergistic effect of the cross-linker and the reinforcing agent. The addition of TA enhanced the ultraviolet blocking and mechanical properties of the chitosan-based nanocomposite film. The reinforcement of TiO2 in chitosan/TA further improved the nanocomposite film’s mechanical properties compared to the neat chitosan or chitosan/TA film. The thermal stability of the chitosan-based nanocomposite film was slightly enhanced, whereas the swelling ratio decreased. Interestingly, its water vapor barrier property was also significantly increased. The developed chitosan-based nanocomposite film showed potent antioxidant activity, and it is promising for active food packaging.

scholarly journals Adhesive Resins with High Shelf-Life Stability Based on Tetra Unsaturated Monomers with Tertiary Amines Moieties

Polymers ◽  
2021 ◽  
Vol 13 (12) ◽  
pp. 1944
Author(s):  
Alma Antonia Pérez-Mondragón ◽  
Carlos Enrique Cuevas-Suárez ◽  
Jesús García-Serrano ◽  
Nayely Trejo-Carbajal ◽  
A. Lobo-Guerrero ◽  
...  
Keyword(s):  
Tensile Strength ◽  
Double Bond ◽  
Shelf Life ◽  
Polymerization Rate ◽  
Tertiary Amines ◽  
Adhesive Systems ◽  
Double Bond Conversion ◽  
Initiator System ◽  
Ft Ir ◽  
Shelf Life Stability

This work reports the use of two monomers with two tertiary amines and four methacrylic (TTME) or acrylic (TTAC) terminal groups as co-initiators in the formulation of experimental resin adhesive systems. Both monomers were characterized by FT-IR and 1H NMR spectroscopies. The control adhesive was formulated with BisGMA, TEGDMA, HEMA, and the binary system CQ-EDAB as a photo-initiator system. For the experimental adhesives, the EDAB was completely replaced for the TTME or the TTAC monomers. The adhesives formulated with TTME or TTAC monomers achieved double bond conversion values close to 75%. Regarding the polymerization rate, materials formulated with TTME or TTAC achieved lower values than the material formulated with EDAB, giving them high shelf-life stability. The degree of conversion after shelf simulation was only reduced for the EDAB material. Ultimate tensile strength, translucency parameter, and micro-tensile bond strength to dentin were similar for control and experimental adhesive resins. Due to their characteristics, TTME and TTAC monomers are potentially useful in the formulation of photopolymerizable resins for dental use with high shelf-life stability.

scholarly journals Antimicrobial Active Bioplastics Using Triangular Silver Nanoplate Integrated Polycaprolactone and Polylactic Acid Films

Materials ◽  
2021 ◽  
Vol 14 (5) ◽  
pp. 1132
Author(s):  
Eduardo Lanzagorta Garcia ◽  
Olivia A. Attallah ◽  
Marija Mojicevic ◽  
Declan M Devine ◽  
Margaret Brennan Fournet
Keyword(s):  
Polylactic Acid ◽  
Scale Up ◽  
Composite Films ◽  
Antimicrobial Properties ◽  
Morphological Structure ◽  
Antimicrobial Effect ◽  
Solvent Casting ◽  
Local Surface Plasmon Resonance ◽  
Casting Technique ◽  
Triangular Silver Nanoplates

An innovative antimicrobial technology for plastic surfaces is presented. We report the synthesis and scale-up of triangular silver nanoplates (TSNPs) and their integration into polycaprolactone (PCL) and polylactic acid (PLA) polymers through a solvent-casting technique. The TSNPs have a high geometric aspect ratio and strong local surface plasmon resonance (LSPR) response, which provides an effective tool for monitoring their integrity during processing and integration with the biodegradable plastics. An aqueous-based seed-mediated chemical method was used to synthesize the TSNPs, and characterisation was carried out using TEM and UV (Ultraviolet)-VIS (Visible) spectroscopy to measure LSPR profiles. The UV-VIS spectra of silver seeds and TSNPs exhibited characteristic peaks at 395 and 600 nm respectively. Synthesized TSNPs were coated with thiol-terminated polyethylene glycol (SH-PEG) and transferred into chloroform in order to effect compatibility with PCL and PLA. TSNP/PCL and TSNP/PLA composite films were prepared by solvent casting. The morphological structure, thermal, mechanical, and antimicrobial properties of the TSNP-incorporated composite films were evaluated. Results showed the TSNP-treated films had a rougher surface than the bare films. Insignificant changes in the thermal properties of TSNP-treated films compared to bare ones were also observed, which indicated the thermal stability of the composite films. The tensile strength and antimicrobial properties of the composite films were increased after TSNP incorporation. TSNP/PCL and TSNP/PLA films exhibited improved antimicrobial activity against Escherichia coli and Staphylococcus aureus with antimicrobial effect (AE) values ranging between 0.10 and 0.35. The obtained results and demonstrated TSNP production scalability validate the TSNP treated PCL and PLA films as a composite material with desirable antimicrobial effect for wide-ranging surface applications.

scholarly journals Sulfonated poly(arylene ether sulfone) functionalized polysilsesquioxane hybrid membranes with enhanced proton conductivity

e-Polymers ◽  
2020 ◽  
Vol 20 (1) ◽  
pp. 430-442 ◽  
Author(s):  
Rajdeep Mukherjee ◽  
Arun Kumar Mandal ◽  
Susanta Banerjee
Keyword(s):  
Proton Conductivity ◽  
Sol Gel ◽  
Composite Membranes ◽  
Casting Technique ◽  
Force Microscopy ◽  
Arylene Ether ◽  
Transmission Electron ◽  
Uniform Dispersion ◽  
Solution Casting Technique ◽  
Sulfonated Poly

AbstractSulfopropylated polysilsesquioxane and –COOH containing fluorinated sulfonated poly(arylene ether sulfone) composite membranes (SPAES-SS-X) have been prepared via an in situ sol–gel reaction through the solution casting technique. The composite membranes showed excellent thermal and chemical stability, compared to the pristine SPAES membrane. The uniform dispersion of the sulfonated SiOPS nanoparticles on the polymer matrix was observed from the scanning electron microscope images. Atomic force microscopy and transmission electron microscopy images indicated significantly better phase-separated morphology and connectivity of the ionic domains of the composite membranes than the pristine SPAES membrane. The composite membranes showed considerable improvement in proton conductivity and oxidative stability than the pristine copolymer membrane under similar test conditions.

Sign in / Sign up

Export Citation Format

Share Document