scholarly journals Evaluation of the Impact of Organic Fillers on Selected Properties of Organosilicon Polymer

Polymers ◽  
2021 ◽  
Vol 13 (7) ◽  
pp. 1103
Author(s):  
Sara Sarraj ◽  
Małgorzata Szymiczek ◽  
Tomasz Machoczek ◽  
Maciej Mrówka
Keyword(s):  
Tensile Strength ◽  
Natural Fiber ◽  
Accelerated Aging ◽  
Strength Properties ◽  
Visual Observation ◽  
Walnut Shell ◽  
Pistachio Shell ◽  
Thermoplastic Matrix ◽  
Static Tensile ◽  
The Impact

Eco-friendly composites are proposed to substitute commonly available polymers. Currently, wood–plastic composites and natural fiber-reinforced composites are gaining growing recognition in the industry, being mostly on the thermoplastic matrix. However, little data are available about the possibility of producing biocomposites on a silicone matrix. This study focused on assessing selected organic fillers’ impact (ground coffee waste (GCW), walnut shell (WS), brewers’ spent grains (BSG), pistachio shell (PS), and chestnut (CH)) on the physicochemical and mechanical properties of silicone-based materials. Density, hardness, rebound resilience, and static tensile strength of the obtained composites were tested, as well as the effect of accelerated aging under artificial seawater conditions. The results revealed changes in the material’s properties (minimal density changes, hardness variation, overall decreasing resilience, and decreased tensile strength properties). The aging test revealed certain bioactivities of the obtained composites. The degree of material degradation was assessed on the basis of the strength characteristics and visual observation. The investigation carried out indicated the impact of the filler’s type, chemical composition, and grain size on the obtained materials’ properties and shed light on the possibility of acquiring ecological silicone-based materials.

scholarly journals Karakterisasi Mekanik Komposit Matriks Polipropilena High Impact Dengan Serat Alam Acak Dengan Metode Hand Lay Up Untuk Komponen Automotive

2020 ◽  
Vol 3 (3) ◽  
Author(s):  
Alfan Ekajati Latief ◽  
Nuha Desi Anggraeni ◽  
Dedy Hernady
Keyword(s):  
Tensile Strength ◽  
Natural Fiber ◽  
Volume Fraction ◽  
Natural Fibers ◽  
Mesh Size ◽  
High Impact ◽  
Hemp Fiber ◽  
Polypropylene Matrix ◽  
The Impact ◽  
Pineapple Leaves

ABSTRAK Serat alam yang berfungsi sebagai penguat memiliki sifat yang lebih ringan, mudah dibentuk, tahan korosi, harga murah dan memiliki kekuatan yang sama dengan material logam. Serat bahan alami yang memiliki kekuatan tarik, tekan dan impak yang baik diantaranya serat rami dan daun nanas. Untuk matriks Polipropilena high impact (PPHI) yang banyak digunakan dalam industri otomotif.. Pada penelitian ini dipelajari pengaruh fraksi volume serat alami terhadap sifat mekanik komposit PPHI berpenguat serat alami. Komposit PPHI dibuat dengan menggunakan metode Hand Lay Up pada temperatur 2500C dengan fraksi volume serat alami sebesar 10%, dimana serat dibuat digunting halus hingga memiliki ukuran mesh 120/170, 170/200 dan dibawah 200 mesh, Kekuatan tarik komposit diukur dengan mengacu pada standar ASTM 3039, kekuatan tekan diukur mengacu pada ASTM D 695. Harga Impak dari komposit diukur dengan mengacu pada ASTM D 6110-04. Pada penelitian ini dapat disimpulkan, fraksi volume 10 % serat alami yang baik ketika dicampur dengan matriks polipropilena high impact adalah serat nanas dengan meshing 170/200 dapat meningkatkan kekuatan tarik PPHI sebesar 40 % dan meningkatkan harga impak PPHI sebesar 50,8 % jika dilihat penelitan sebelumnya yakni menggunakan serat rami dibawah mesh 1200 dengan matriks PPHI. Kata Kunci: Rami, Daun Nanas, Polipropilena High Impact, Hand Lay Up. ABSTRACT Natural fibers that function as reinforcement have lighter properties, are easily formed, are corrosion resistant, are cheap and have the same strength as metal materials. Natural fiber which has good tensile, compressive and impact strength including Ramie and pineapple leaves. For high impact polypropylene matrix (PPHI) which is widely used in the automotive industry. In this study the effect of volume fraction of natural fibers on the mechanical properties of PPHI composites with natural fiber reinforced properties was studied. PPHI composites are made using the Hand Lay Up method at a temperature of 2500C with a volume fraction of natural fibers of 10%, where fibers are made finely shaved to have a mesh size of 120/170, 170/200 and below 200 mesh, the tensile strength of the composite is measured by reference to the standard ASTM 3039, compressive strength measured refers to ASTM D 695. The impact price of the composite is measured with reference to ASTM D 6110-04. In this study it can be concluded, a good volume fraction of 10% natural fiber when mixed with high impact polypropylene matrix is pineapple fiber with meshing 170/200 can increase the tensile strength of PPHI by 40% and increase the impact price of PPHI by 50.8% if seen by research previously that used hemp fiber under mesh 1200 with PPHI matrix. Keywords: Ramie Pineapple, High Impact Polypropylene, Hand Lay Up.

Impact of Process Parameters on the Tensile Properties of DLP Additively Manufactured ELAST-BLK 10 UV-Curable Elastomer

2021 ◽  
Author(s):  
Asma Ul Hosna Meem ◽  
Kyle Rudolph ◽  
Allyson Cox ◽  
Austin Andwan ◽  
Timothy Osborn ◽  
...  
Keyword(s):  
Tensile Strength ◽  
Elastic Modulus ◽  
Ultimate Tensile Strength ◽  
Tensile Properties ◽  
Process Parameters ◽  
Uv Light ◽  
Uv Curable ◽  
Build Orientation ◽  
Static Tensile ◽  
The Impact

Abstract Digital light processing (DLP) is an emerging vatphotopolymerization-based 3D-printing technology where full layers of photosensitive resin are irradiated and cured with projected ultraviolet (UV) light to create a three-dimensional part layer-by-layer. Recent breakthroughs in polymer chemistry have led to a growing number of UV-curable elastomeric photoresins developed exclusively for vat photopolymerization additive manufacturing (AM). Coupled with the practical manufacturing advantages of DLP AM (e.g., industry-leading print speeds and sub-micron-level print resolution), these novel elastomeric photoresins are compelling candidates for emerging applications requiring extreme flexibility, stretchability, conformability, and mechanically-tunable stiffness (e.g., soft robotic actuators and stretchable electronics). To advance the role of DLP AM in these novel and promising technological spaces, a fundamental understanding of the impact of DLP manufacturing process parameters on mechanical properties is requisite. This paper highlights our recent efforts to explore the process-property relationship for ELAST-BLK 10, a new commercially-available UV-curable elastomer for DLP AM. A full factorial design of experiments is used to investigate the effect of build orientation and layer thickness on the quasi-static tensile properties (i.e., small-strain elastic modulus, ultimate tensile strength, and elongation at fracture) of ELAST-BLK 10. Statistical results, based on a general linear model via ANOVA methods, indicate that specimens with a flat build orientation exhibit the highest elastic modulus, ultimate tensile strength, and elongation at fracture, likely due to a larger surface area that enhances crosslink density during the curing process. Several popular hyperelastic constitutive models (e.g., Mooney-Rivlin, Yeoh, and Gent) are calibrated to our quasi-static tensile data to facilitate component-level predictive analyses (e.g., finite-element modeling) of soft robotic actuators and other emerging soft-matter applications.

scholarly journals Mechanical Properties for Elephant Dung and its Utilization as a Raw Material Composites Sheet: A Study

2021 ◽  
Vol 10 (1) ◽  
pp. 1-7
Author(s):  
Rohit Kumar ◽  
Ramratan . ◽  
Anupam Kumar ◽  
Rajinder Singh Smagh
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Impact Strength ◽  
Polymer Composite ◽  
Natural Fiber ◽  
Testing Machine ◽  
Raw Material ◽  
Weight Percentage ◽  
The Impact ◽  
Elephant Dung

Elephant dung is an excellent source of cellulosic fiber that is a basic requirement for paper making. But they contributed to very small percentage production of elephant dung. So, researchers are trying to find a new area of utilization of elephant dung fiber pulp as in reinforcement’s polymer composite. In this experiment element dung fiber pulp in the natural fiber component chemically treated with alkaline and soda AQ solution in this study, it has been aimed to use elephant dung fiber pulp in composite material and to study mechanical properties of the produced material. The produced composite samples were then characterized using tensile test, Izod impact test, thickness test. The fracture surface of the polymer composite sample was also inspected with the help of SEM. The content of elephant dung fiber pulp is varied (35%, 45%, 55%) weight percentage whereas the epoxy resin is varied (50%, 40%, 30%) percentage is kept constant 15% in hardener. The entire sample has been tested in a universal testing machine as per ASTM standard for tensile strength and impact strength. It is observed that composite with 35% fiber pulp is having the highest tensile strength of 4mm 6.445 Mpa and 8mm 11.80 Mpa. The impact strength of composite with 35% fiber pulp washes highest than 45% to 55% dung fiber pulp. This produces composite sheet will be used for the surfboards, sporting goods, building panel this not only reduces the cost but also save from environmental pollution.

Impact of Alkali Treatment Conditions on Kenaf Fiber Polyester Composite Tensile Strength

2014 ◽  
Vol 660 ◽  
pp. 285-289 ◽  
Author(s):  
Mohd Yussni Hashim ◽  
Mohd Nazrul Roslan ◽  
Shahruddin Mahzan ◽  
Mohd Zin ◽  
Saparudin Ariffin
Keyword(s):  
Tensile Strength ◽  
Immersion Time ◽  
Natural Fiber ◽  
Alkali Treatment ◽  
Solution Temperature ◽  
Type I ◽  
Kenaf Fiber ◽  
Treatment Conditions ◽  
Polyester Composite ◽  
The Impact

The increase of environmental issues awareness has accelerated the utilization of renewable resources like plant fiber to be used as reinforced material in polymer composite. However, there are significant problems of compatibility between the fiber and the matrix due to weakness in the interfacial adhesion of the natural fiber with the synthetic matrices. One of the solutions to overcome this problem is using chemical modification like alkali treatment. In this study, the impact of alkali treatment conditions on short randomly oriented kenaf fiber reinforced polyester matrix composite tensile strength was investigated. The experimental design setting was based on 2 level factorial experiments. Two parameters were selected during alkali treatment process which are kenaf fiber immersion duration (at 30 minute and 480 minute) and alkali solution temperature (at 40°C and 80°C). Alkali concentration was fixed at 2% (w/v) and the kenaf polyester volume fraction ratio was 10:90. The composite specimens were tested to determine the tensile properties according to ASTM D638-10 Type I. JOEL scanning electron microscopy (SEM) was used to study the microstructure of the material. The result showed that alkali treatment conditions setting do have the impact on tensile strength of short randomly oriented kenaf polyester composite. The interaction factors between immersion time and temperature was found to have prominent factors to the tensile strength of composite followed by the immersion time factor.

scholarly journals Transformative Use of Additive Technology in Design and Manufacture of Hydraulic Actuator for Fly-by-Wire System

2021 ◽  
Vol 11 (11) ◽  
pp. 4772
Author(s):  
Krzysztof Warzocha ◽  
Jerzy Szura ◽  
Piotr Bąk ◽  
Paweł Rzucidło ◽  
Tomasz Rogalski
Keyword(s):  
Flight Control ◽  
Tensile Testing ◽  
High Performance ◽  
Strength Properties ◽  
Hydraulic Actuator ◽  
Aircraft Flight Control ◽  
Static Tensile ◽  
Goodman Diagram ◽  
Design And Manufacture ◽  
The Impact

In this paper, the results of research on additively manufactured aerospace parts made of maraging steel are presented. This state-of-the-art technology seems to have the highest potential for practical use in the field of ultra-light and high-performance aerospace hydraulic parts. The strength properties of representative specimens made with steel 1.2709 were investigated. The researchers conducted static tensile testing, fatigue tensile testing, and pressure impulse testing. A Goodman diagram was plotted to visualize the impact of the building orientation vs. load character on the fatigue strength of the additive manufacturing (AM) specimens. Based on the research carried out on the strength of the AM samples, an aircraft flight control actuator was designed to achieve the highest level of safety integrity along with the greatest simplicity and lowest weight relative to hydraulic actuators manufactured using classical methods. The entire design process was integrated with the manufacturing process to achieve this target.

scholarly journals Impact of Design Parameters on the Ratio of Compressive to Split Tensile Strength of Self-Compacting Concrete with Recycled Aggregate

Materials ◽  
2021 ◽  
Vol 14 (13) ◽  
pp. 3480
Author(s):  
Rebeca Martínez-García ◽  
P. Jagadesh ◽  
Gabriel Búrdalo-Salcedo ◽  
Covadonga Palencia ◽  
María Fernández-Raga ◽  
...  
Keyword(s):  
Tensile Strength ◽  
Strength Properties ◽  
Recycled Aggregate ◽  
Recycled Aggregates ◽  
Design Parameters ◽  
Fine Aggregate ◽  
Strength Ratio ◽  
Self Compacting Concrete ◽  
Split Tensile Strength ◽  
The Impact

Most concrete studies are concentrated on mechanical properties especially strength properties either directly or indirectly (fresh and durability properties). Hence, the ratio of split tensile strength to compressive strength plays a vital role in defining the concrete properties. In this review, the impact of design parameters on the strength ratio of various grades of Self-Compacting Concrete (SCC) with recycled aggregate is assessed. The design parameters considered for the study are Water to Cement (W/C) ratio, Water to Binder (W/B) ratio, Total Aggregates to Cement (TA/C) ratio, Fine Aggregate to Coarse Aggregate (FA/CA) ratio, Water to Solid (W/S) ratio in percentage, superplasticizer (SP) content (kg/cu.m), replacement percentage of recycled coarse aggregates (RCA), replacement percentage of recycled fine aggregates (RFA), fresh density and loading area of the specimen. It is observed that the strength ratio of SCC with recycled aggregates is affected by design parameters.

scholarly journals The Effects of Sodium Hydroxide and Soda AQ Content on Mechanical and Physical Properties of Waste Flax Fibre Pulp Reinforced Polymer Composite Sheet

2020 ◽  
Vol 9 (2) ◽  
pp. 8-15
Author(s):  
Anupam Kumar ◽  
Ramratan . ◽  
Rohit Kumar
Keyword(s):  
Tensile Strength ◽  
Impact Strength ◽  
Epoxy Resin ◽  
Natural Fiber ◽  
Testing Machine ◽  
Flax Fiber ◽  
Alkaline Solutions ◽  
Volume Percentage ◽  
Flax Fibres ◽  
The Impact

The aim of this study is utilized agricultural waste which may be profitable, pollution free and economically viable for the farmer and industries. In this experiment short flax fiber pulp is the natural fiber component chemically treated with alkaline solutions. Six specimens will be prepared in different volume percentage of flax fiber pulp and epoxy resin in order to get more accurate results. In this study it has been aimed to use flax fibres in composite materials and to study the mechanical properties of the produced samples. The mechanical tests results (thickness test, Tensile strength and impact strength tests) and SEM micrographs indicated flax fibres as an alternative natural fibre source for developing reinforced composites for various industries. The content of short flax fiber pulp is varied (35%, 45%, 55%) weight percentage whereas the epoxy resin is varied (50%, 40%, 30%) percentage is kept constant 15% in hardener. All the sample have been tested in universal testing machine as per ASTM standard for tensile strength and impact strength it is observed that composite with 35% flax fiber pulp is having highest tensile strength of 4 mm (4.57 Mpa) and 8 mm (6.04 Mpa). The impact strength of composite with 35% flax fiber pulp was highest than 45% to 55% flax fiber pulp.

scholarly journals Effect of Al2O3 on the Tensile and Impact Strength of Flax/Unsaturated Polyester Composite with Emphasis on Automobile Body Applications

2021 ◽  
Vol 2021 ◽  
pp. 1-9
Author(s):  
Gebre Fenta Aynalem ◽  
Belete Sirahbizu
Keyword(s):  
Impact Strength ◽  
Polyester Resin ◽  
Natural Fiber ◽  
Resin Composite ◽  
Unsaturated Polyester ◽  
Fiber Material ◽  
Strength Properties ◽  
Unsaturated Polyester Resin ◽  
Molding Process ◽  
The Impact

This study has endeavored to develop an Al2O3-filled natural fiber reinforced polymer composite which is intended to substitute the most widely used synthetic E-glass fiber material. To attain the desired objective of the work, 0, 5, 10, and 15 wt% Al2O3-filled chopped flax/unsaturated polyester resin composite have been developed by the conventional hand-lay-up method followed by a compression molding process. Consequently, characterization and mechanical property tests are conducted based on the ASTM standard. The results revealed that both tensile and impact strength properties of the base chopped flax/unsaturated polyester resin composite are all affected due to the inclusion and variation of the content of Al2O3 in 15 and 25 wt% fiber loading cases. It has been noticed that a 39.06% increase in the ultimate tensile strength of the composite in 25/UPR-5 composition has been gained. The effect of Al2O3 on the impact strength of the base composite has also been analyzed and a 45% increase has been observed in 15/UPR-10 composition. The findings also witnessed that the newly developed composite can be applied to make automotive parts such as mud guard and engine undercover.

scholarly journals Fabrication of Epoxy Composites Reinforced with Bamboo Fibers

2020 ◽  
pp. 1-7
Author(s):  
Mohammed Khazal ◽  
Salman H. Abbas ◽  
Younis M. Younis ◽  
Thabit Jamel
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Impact Strength ◽  
Bending Strength ◽  
Natural Fiber ◽  
Natural Fibers ◽  
Percentage Increase ◽  
High Mechanical Strength ◽  
Bamboo Fibers ◽  
The Impact

This study aims to enhance the mechanical properties of polymer material using type of natural fiber. Bamboo fiber considered the strongest between the natural fibers group, it have low density, high mechanical strength in addition to its availability makes it economically viable and have potential for used as engineering material. The study is concerned with evaluate some of the mechanical properties (Tensile strength, Bending strength, Impact strength) for the resultant composite reinforced with 10, 20 and 30 vol.% of bamboo fibers, as compared with received material. With the natural reinforcement, the optimum mechanical properties in comparison with the as received epoxy were achieved. The results indicated that the tensile strength increased from 13.51 MPa to 33.50 MPa (that is a percentage increase of 150 %), also the bending strength increased from 24.25 MPa to 44.5 MPa (that is a percentage increase about 83 %), as well as, the increase of the impact strength from 41 kJ/m2 to 69 kJ/m2 (that is a percentage increase about 68 %).

The influence of alkaline treatment on acoustical, morphological, tensile and thermal properties of Kenaf natural fibers

2020 ◽  
pp. 152808372094424
Author(s):  
Seyed Ehsan Samaei ◽  
Hasan Asilian Mahabadi ◽  
Seyyed Mohammad Mousavi ◽  
Ali Khavanin ◽  
Mohammad Faridan ◽  
...  
Keyword(s):  
Tensile Strength ◽  
Sound Absorption ◽  
Hybrid Composites ◽  
Natural Fibers ◽  
Alkaline Treatment ◽  
Strength Properties ◽  
Absorption Coefficients ◽  
Surface Appearance ◽  
Kenaf Fibers ◽  
The Impact

Among fibers with lignocellulosic origin, Kenaf fiber, because of its advantages and as a sustainable alternative to synthetic fibers has received increasing attention for manufacturing hybrid composites with reasonable acoustical and physical properties. The present study deals with the impact of chemical treatment of Kenaf fibers on the overall properties of hybrid composites fabricated from these fibers. Also, the results from predictive analytical model of sound absorption for these composites were employed for comparison with the experimental findings. Kenaf fibers were treated at room temperature with 6% concentration of sodium hydroxide (NaOH) and 4 h immersion time. Having manufactured the composites with the treated and untreated fibers, the normal sound absorption coefficients and tensile strength properties of these sample composites were determined according to ISO 10534-2 and ASTM C1557 − 14, respectively. The SEM analysis of the treated and untreated fibers revealed that in terms of fiber diameter and morphology the former was thinner and had better surface appearance. The experimental measurement of acoustic absorption coefficients of the composites made of treated fibers demonstrated superior sound absorption properties and tensile strength. The revised empirical models proposed by Delany & Bazley and Garai & Pompoli along with Nelder-Mead simplex method were employed and well predicted the sound absorption coefficients of the sample composites. There was also a fair consistency between the experimental and predicted results.

Sign in / Sign up

Export Citation Format

Share Document