scholarly journals Effect of DMPA and Molecular Weight of Polyethylene Glycol on Water-Soluble Polyurethane

Polymers ◽  
2019 ◽  
Vol 11 (12) ◽  
pp. 1915 ◽  
Author(s):  
Eyob Wondu ◽  
Hyun Woo Oh ◽  
Jooheon Kim
Keyword(s):  
Molecular Weight ◽  
Contact Angle ◽  
Polyethylene Glycol ◽  
Photoelectron Spectroscopy ◽  
Water Solubility ◽  
Soft Segment ◽  
Water Soluble ◽  
Size Exclusion ◽  
Resonance Spectroscopy ◽  
Scanning Calorimetry

In this study water-soluble polyurethane (WSPU) was synthesized from isophorone diisocyanate (IPDI), and polyethylene glycol (PEG), 2-bis(hydroxymethyl) propionic acid or dimethylolpropionic acid (DMPA), butane-1,4-diol (BD), and triethylamine (TEA) using an acetone process. The water solubility was investigated by solubilizing the polymer in water and measuring the contact angle and the results indicated that water solubility and contact angle tendency were increased as the molecular weight of the soft segment decreased, the amount of emulsifier was increased, and soft segment to hard segment ratio was lower. The contact angle of samples without emulsifier was greater than 87°, while that of with emulsifier was less than 67°, indicating a shift from highly hydrophobic to hydrophilic. The WSPU was also analyzed using Fourier transform infrared spectroscopy (FT-IR) to identify the absorption of functional groups and further checked by X-ray photoelectron spectroscopy (XPS). The molecular weight of WSPU was measured using size-exclusion chromatography (SEC). The structure of the WSPU was confirmed by nuclear magnetic resonance spectroscopy (NMR). The thermal properties of WSPU were analyzed using thermogravimetric analysis (TGA), and differential scanning calorimetry (DSC).

Synthesis and Characterization of Poly (styrene-co-butyl acrylate)/Silica Aerogel Nanocomposites by in situ AGET ATRP: Investigating Thermal Properties

2017 ◽  
Vol 36 (10) ◽  
pp. 955-962 ◽  
Author(s):  
Khezrollah Khezri ◽  
Yousef Fazli
Keyword(s):  
Molecular Weight ◽  
Butyl Acrylate ◽  
Silica Aerogel ◽  
Size Exclusion ◽  
Proton Nuclear Magnetic Resonance ◽  
Molar Ratio ◽  
Resonance Spectroscopy ◽  
Gravimetric Analysis ◽  
Scanning Calorimetry ◽  
Exclusion Chromatography

AbstractHydrophilic silica aerogel nanoparticles surface was modified with hexamethyldisilazane. Then, the resultant modified nanoparticles were used in random copolymerization of styrene and butyl acrylate via activators generated by electron transfer for atom transfer radical polymerization. Conversion and molecular weight determinations were performed using gas and size exclusion chromatography respectively. Addition of modified nanoparticles by 3 wt% results in a decrease of conversion from 68 to 46 %. Molecular weight of copolymer chains decreases from 12,500 to 7,500 g.mol–1 by addition of 3 wt% modified nanoparticles; however, PDI values increase from 1.1 to 1.4. Proton nuclear magnetic resonance spectroscopy results indicate that the molar ratio of each monomer in the copolymer chains is approximately similar to the initial selected mole ratio of them. Increasing thermal stability of the nanocomposites is demonstrated by thermal gravimetric analysis. Differential scanning calorimetry also shows a decrease in glass transition temperature by increasing modified silica aerogel nanoparticles.

scholarly journals Recoverable Water-soluble Polyethylene Glycol-immobilized N-hydroxyphthalimide Mediated Oxidation of Cellulose in the Presence of NaBr and NaClO

2021 ◽  
Author(s):  
Huimin Wang ◽  
Xiaoying Wang ◽  
Tingting Sun ◽  
Peixin Li ◽  
Xiaomeng Chu ◽  
...  
Keyword(s):  
Polyethylene Glycol ◽  
Water Solubility ◽  
Cellulose Degradation ◽  
Catalytic Performance ◽  
Water Soluble ◽  
Resonance Spectroscopy ◽  
Oxidized Cellulose ◽  
Carboxyl Content ◽  
Selective Catalytic Oxidation ◽  
Mediated Oxidation

Abstract As a highly efficient nitroxide radical catalyst for selective catalytic oxidation of cellulose, N-hydroxyphthalimide (NHPI) has attracted much attention because of its low price and light cellulose degradation. However, NHPI is insoluble in water and is difficult to recycle because of its small molecular weight. To address the above issues, the water-soluble polyethylene glycol (PEG)-immobilized NHPI catalyst (PEG-NHPI) was designed and prepared in this work. Fourier transform infrared spectroscopy (FT-IR), nuclear magnetic resonance spectroscopy (NMR), gel permeation chromatography (GPC) and UV-vis light spectroscopy were used to characterize PEG-NHPI. The results showed that PEG-NHPI catalysts with good water solubility and adjustable NHPI loading amounts were successfully synthesized. Using NaBr as promoter and NaClO as oxidant, PEG-NHPI mediated oxidation of cellulose was carried out and good catalytic performance was found. The catalytic performance of PEG-NHPI mediated oxidation of cellulose in water was higher than that in acetonitrile-water. The carboxyl content of PEG-NHPI oxidized cellulose could reach the level of free NHPI oxidized cellulose, and was equivalent to 68% of 2,2,6,6-tetramethyl-1-piperidinyloxy (TEMPO) oxidized cellulose, while the degradation degree of cellulose was greatly reduced by more than 40%. The catalytic performance did not decrease significantly after six oxidation cycles. The structure of recycled PEG-NHPI was not changed. These results indicated that immobilizing NHPI onto PEG can achieve the unification of high catalytic performance and good recyclability.

Structure of a shear-thickening polysaccharide extracted from the New Zealand black tree fern, Cyathea medullaris

2020 ◽  
Author(s):  
M Wee ◽  
M Mastrangelo ◽  
Susan Carnachan ◽  
Ian Sims ◽  
K Goh
Keyword(s):  
New Zealand ◽  
Uronic Acid ◽  
Average Molecular Weight ◽  
Shear Thickening ◽  
Water Soluble ◽  
Size Exclusion ◽  
Resonance Spectroscopy ◽  
Tree Fern ◽  
13C Nuclear Magnetic Resonance ◽  
Exclusion Chromatography

A shear-thickening water-soluble polysaccharide was purified from mucilage extracted from the fronds of the New Zealand black tree fern (Cyathea medullaris or 'mamaku' in Māori) and its structure characterised. Constituent sugar analysis by three complementary methods, combined with linkage analysis (of carboxyl reduced samples) and 1H and 13C nuclear magnetic resonance spectroscopy (NMR) revealed a glucuronomannan comprising a backbone of 4-linked methylesterified glucopyranosyl uronic acid and 2-linked mannopyranosyl residues, branched at O-3 of 45% and at both O-3 and O-4 of 53% of the mannopyranosyl residues with side chains likely comprising terminal xylopyranosyl, terminal galactopyranosyl, non-methylesterified terminal glucopyranosyl uronic acid and 3-linked glucopyranosyl uronic acid residues. The weight-average molecular weight of the purified polysaccharide was ~1.9×106Da as determined by size-exclusion chromatography coupled with multi-angle laser light scattering (SEC-MALLS). The distinctive rheological properties of this polysaccharide are discussed in relation to its structure. © 2014 Elsevier B.V.

scholarly journals Impact of Macrodiols on the Morphological Behavior of H12MDI/HDO-Based Polyurethane Elastomer

Polymers ◽  
2021 ◽  
Vol 13 (13) ◽  
pp. 2060
Author(s):  
Shazia Naheed ◽  
Mohammad Zuber ◽  
Mahwish Salman ◽  
Nasir Rasool ◽  
Zumaira Siddique ◽  
...  
Keyword(s):  
Molecular Weight ◽  
Contact Angle ◽  
Chain Length ◽  
Microphase Separation ◽  
Soft Segment ◽  
Group Identification ◽  
Degree Of Crystallinity ◽  
Polyurethane Elastomers ◽  
Hard Segments ◽  
Morphological Behavior

In this study, we evaluated the morphological behavior of polyurethane elastomers (PUEs) by modifying the soft segment chain length. This was achieved by increasing the soft segment molecular weight (Mn = 400–4000 gmol−1). In this regard, polycaprolactone diol (PCL) was selected as the soft segment, and 4,4′-cyclohexamethylene diisocyanate (H12MDI) and 1,6-hexanediol (HDO) were chosen as the hard segments. The films were prepared by curing polymer on Teflon surfaces. Fourier transform infrared spectroscopy (FTIR) was utilized for functional group identification in the prepared elastomers. FTIR peaks indicated the disappearance of −NCO and −OH groups and the formation of urethane (NHCOO) groups. The morphological behavior of the synthesized polymer samples was also elucidated using scanning electron microscopy (SEM) and atomic force microscopy (AFM) techniques. The AFM and SEM results indicated that the extent of microphase separation was enhanced by an increase in the molecular weight of PCL. The phase separation and degree of crystallinity of the soft and hard segments were described using X-ray diffraction (XRD). It was observed that the degree of crystallinity of the synthesized polymers increased with an increase in the soft segment’s chain length. To evaluate hydrophilicity/hydrophobicity, the contact angle was measured. A gradual increase in the contact angle with distilled water and diiodomethane (38.6°–54.9°) test liquids was observed. Moreover, the decrease in surface energy (46.95–24.45 mN/m) was also found to be inconsistent by increasing the molecular weight of polyols.

scholarly journals Enhanced Water Solubility and Oral Bioavailability of Paclitaxel Crystal Powders through an Innovative Antisolvent Precipitation Process: Antisolvent Crystallization Using Ionic Liquids as Solvent

Pharmaceutics ◽  
2020 ◽  
Vol 12 (11) ◽  
pp. 1008 ◽  
Author(s):  
Qilei Yang ◽  
Chang Zu ◽  
Wengang Li ◽  
Weiwei Wu ◽  
Yunlong Ge ◽  
...  
Keyword(s):  
Oral Bioavailability ◽  
High Performance ◽  
Water Solubility ◽  
Water Soluble ◽  
Precipitation Process ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
Antisolvent Precipitation ◽  
Antisolvent Crystallization ◽  
Artificial Gastric Juice

Paclitaxel (PTX) is a poor water-soluble antineoplastic drug with significant antitumor activity. However, its low bioavailability is a major obstacle for its biomedical applications. Thus, this experiment is designed to prepare PTX crystal powders through an antisolvent precipitation process using 1-hexyl-3-methylimidazolium bromide (HMImBr) as solvent and water as an antisolvent. The factors influencing saturation solubility of PTX crystal powders in water in water were optimized using a single-factor design. The optimum conditions for the antisolvent precipitation process were as follows: 50 mg/mL concentration of the PTX solution, 25 °C temperature, and 1:7 solvent-to-antisolvent ratio. The PTX crystal powders were characterized via scanning electron microscopy, Fourier transform infrared spectroscopy, high-performance liquid chromatography–mass spectrometry, X-ray diffraction, differential scanning calorimetry, thermogravimetric analysis, Raman spectroscopy, solid-state nuclear magnetic resonance, and dissolution and oral bioavailability studies. Results showed that the chemical structure of PTX crystal powders were unchanged; however, precipitation of the crystalline structure changed. The dissolution test showed that the dissolution rate and solubility of PTX crystal powders were nearly 3.21-folds higher compared to raw PTX in water, and 1.27 times higher in artificial gastric juice. Meanwhile, the bioavailability of PTX crystal increased 10.88 times than raw PTX. These results suggested that PTX crystal powders might have potential value to become a new oral PTX formulation with high bioavailability.

Formulation and Evaluation of Benidipine Nanosuspension

2021 ◽  
pp. 4111-4116
Author(s):  
Sejal Patel ◽  
Anita P. Patel
Keyword(s):  
Particle Size ◽  
Water Solubility ◽  
Polymer Concentration ◽  
Oral Route ◽  
Water Soluble ◽  
In Vitro Dissolution ◽  
Scanning Calorimetry ◽  
23 Factorial Design ◽  
Selection Of

In the interest of administration of dosage form oral route is most desirable and preferred method. After oral administration to get maximum therapeutic effect, major challenge is their water solubility. Water insoluble drug indicate insufficient bioavailability as well dissolution resulting in fluctuating plasma level. Benidipine (BND) is poorly water soluble antihypertensive drug has lower bioavailability. To improve bioavailability of Benidipine HCL, BND nanosuspension was formulated using media milling technique. HPMC E5 was used to stabilize nanosuspension. The effect of different important process parameters e.g. selection of polymer concentration X1(1.25 mg), stirring time X2 (800 rpm), selection of zirconium beads size X3 (0.4mm) were investigated by 23 factorial design to accomplish desired particle size and saturation solubility. The optimized batch had 408 nm particle size Y1, and showed in-vitro dissolution Y2 95±0.26 % in 30 mins and Zeta potential was -19.6. Differential scanning calorimetry (DSC) and FT-IR analysis was done to confirm there was no interaction between drug and polymer.

A study on the kinetics and thermal properties of polystyrene/diatomite nanocomposites prepared via in situ ATRP

2018 ◽  
Vol 33 (2) ◽  
pp. 180-197 ◽  
Author(s):  
Khezrollah Khezri ◽  
Yousef Fazli
Keyword(s):  
Molecular Weight ◽  
In Situ Polymerization ◽  
Structural Characteristics ◽  
Nitrogen Adsorption ◽  
Linear Increase ◽  
Size Exclusion ◽  
Scanning Calorimetry ◽  
Morphological Studies ◽  
Exclusion Chromatography

Pristine mesoporous diatomite was employed to prepare polystyrene/diatomite composites. Diatomite platelets were used for in situ polymerization of styrene by atom transfer radical polymerization to synthesize tailor-made polystyrene nanocomposites. X-Ray fluorescence spectrometer analysis and thermogravimetric analysis (TGA) were employed for evaluating some inherent properties of pristine diatomite platelets. Nitrogen adsorption/desorption isotherm is applied to examine surface area and structural characteristics of the diatomite platelets. Evaluation of pore size distribution and morphological studies were also performed by scanning and transmission electron microscopy. Conversion and molecular weight determinations were carried out using gas and size exclusion chromatography, respectively. Linear increase of ln ( M0/M) with time for all the samples shows that polymerization proceeds in a living manner. Addition of 3 wt% pristine mesoporous diatomite leads to an increase of conversion from 72% to 89%. Molecular weight of polystyrene chains increases from 11,326 g mol−1 to 14134 g mol−1 with the addition of 3 wt% pristine mesoporous diatomite; however, polydispersity index values increases from 1.13 to 1.38. Increasing thermal stability of the nanocomposites is demonstrated by TGA. Differential scanning calorimetry shows an increase in glass transition temperature from 81.9°C to 87.1°C by adding 3 wt% of mesoporous diatomite platelets.

Preparation and Characterization of Ni2+-Montmorillonite/Polyvinyl Alcohol Water-Soluble Nanocomposite Film

2005 ◽  
Vol 13 (8) ◽  
pp. 839-846 ◽  
Author(s):  
Li-Ping Wang ◽  
Yun-Pu Wang ◽  
Fa-Ai Zhang
Keyword(s):  
Polyvinyl Alcohol ◽  
Photoelectron Spectroscopy ◽  
Thermal Characteristics ◽  
Water Soluble ◽  
Scanning Calorimetry ◽  
Xps Spectra ◽  
X Ray ◽  
Alcohol Water ◽  
Ft Ir ◽  
Silicate Layers

A new type of nano-composite film was prepared from polyvinyl alcohol, Ni2+-montmorillonite (Ni2+-MMT), defoamer, a levelling agent and a plasticizer. Its thermal characteristics were studied by Differential Scanning Calorimetry (DSC). The intermolecular interactions were measured by Fourier transform infrared spectroscopy (FT-IR) and X-ray photoelectron spectroscopy (XPS), and the tensile strength (TS) and elongation at break (%E) were measured. The microstructures were studied by X-ray diffraction (XRD) and atomic force microscopy (AFM). FT-IR and XPS spectra indicated that cross-linking has taken place between PVA and Ni2+-MMT. XRD and AFM indicate that the PVA molecules had inserted themselves into the silicate layers of MMT, exfoliating them and dispersing them randomly into the PVA matrix. Compared to pure PVA film, the TS of the films was increased and %E decreased when the Ni2+-Montmorillonite was added and the dissolution temperature of the film was also reduced.

scholarly journals Solubility and Dissolution Enhancement of Atorvastatin Calcium using Solid Dispersion Adsorbate Technique

2019 ◽  
Vol 28 (2) ◽  
pp. 105-114
Author(s):  
Samer K. Ali ◽  
Eman B. H. Al-Khedairy
Keyword(s):  
Polyethylene Glycol ◽  
Solid Dispersion ◽  
Water Solubility ◽  
Drug Carrier ◽  
Solid Dispersions ◽  
Poloxamer 407 ◽  
Dissolution Enhancement ◽  
Drug Solubility ◽  
Scanning Calorimetry ◽  
Poorly Soluble

            Atorvastatin (ATR) is poorly soluble anti-hyperlipidemic drug; it belongs to the class II group according to the biopharmaceutical classification system (BCS) with low bioavailability due to its low solubility. Solid dispersions adsorbate is an effective technique for enhancing the solubility and dissolution of poorly soluble drugs.           The present study aims to enhance the solubility and dissolution rate of ATR using solid dispersion adsorption technique in comparison with ordinary solid dispersion. polyethylene glycol 4000 (PEG 4000), polyethylene glycol 6000 (PEG 6000), Poloxamer188 and Poloxamer 407were used as hydrophilic carriers and Aerosil 200, Aerosil 300 and magnesium aluminium silicate (MAS) as adsorbents.            All solid dispersion adsorbate (SDA) formulas  were prepared in ratios of 1:1:1  (drug: carrier: adsorbent) and evaluated for their water solubility, percentage yield, drug content,  , dissolution, crystal structure using  X-ray powder diffraction (XRD) and Differential Scanning Calorimetry (DSC)  studies and Fourier Transform Infrared Spectroscopy (FTIR) for determination the drug-carrier- adsorbate interaction.                The prepared (SDA) showed significant improvement of drug solubility in all prepared formula. Best result was obtained with formula SDA12(ATR :Poloxamer407 : MAS 1:1:1) that showed 8.07 and 5.38  fold increase in solubility compared to  solubility of pure ATR and  solid dispersion(SD4) (Atorvastatin: Poloxamer 407 1:1) respectively due to increased wettability and reduced crystallinity of the drug which leads to improve drug solubility  and  dissolution .

scholarly journals Preparation and Characterization of PEG4000 Palmitate/PEG8000 Palmitate-Solid Dispersion Containing the Poorly Water-Soluble Drug Andrographolide

2020 ◽  
Vol 2020 ◽  
pp. 1-7
Author(s):  
Qingyun Zeng ◽  
Liquan Ou ◽  
Guowei Zhao ◽  
Ping Cai ◽  
Zhenggen Liao ◽  
...  
Keyword(s):  
Thermal Stability ◽  
Molecular Weight ◽  
Dissolution Rate ◽  
Solid Dispersion ◽  
Water Solubility ◽  
Water Soluble ◽  
Carrier Material ◽  
Water Soluble Drug ◽  
Poorly Water Soluble ◽  
Poorly Water Soluble Drug

Solid dispersion (SD) is the effective approach to improve the dissolution rate and bioavailability of class II drugs with low water solubility and high tissue permeability in the Biopharmaceutics Classification System. This study investigated the effects of polyethylene glycol (PEG) molecular weight in carrier material PEG palmitate on the properties of andrographolide (AG)-SD. We prepared SDs containing the poorly water-soluble drug AG by the freeze-drying method. The SDs were manufactured from two different polymers, PEG4000 palmitate and PEG8000 palmitate. The physicochemical properties of the AG-SDs were characterized by Fourier transform infrared spectroscopy, thermogravimetric analysis, differential scanning calorimetry, powder X-ray diffraction, scanning electron microscopy, dissolution testing, and so on. We found that AG-PEG4000 palmitate-SD and AG-PEG8000 palmitate-SD were similar in the surface morphology, specific surface area, and pore volume. Compared with the AG-PEG4000 palmitate-SD, the intermolecular interaction between PEG8000 palmitate and AG was stronger, and the thermal stability of AG-PEG8000 palmitate-SD was better. In the meanwhile, the AG relative crystallinity was lower and the AG dissolution rate was faster in AG-PEG8000 palmitate-SD. The results demonstrate that the increasing PEG molecular weight in the PEG palmitate can improve the compatibility between the poorly water-soluble drug and carrier material, which is beneficial to improve the SD thermal stability and increases the dissolution rate of poorly water-soluble drug in the SD.

Sign in / Sign up

Export Citation Format

Share Document