scholarly journals Interlayer Adhesion Analysis of 3D-Printed Continuous Carbon Fibre-Reinforced Composites

Polymers ◽  
2021 ◽  
Vol 13 (10) ◽  
pp. 1653
Author(s):  
Tomas Kuncius ◽  
Marius Rimašauskas ◽  
Rūta Rimašauskienė
Keyword(s):  
Shear Strength ◽  
Carbon Fibre ◽  
Line Width ◽  
Composite Structures ◽  
Shear Force ◽  
Fused Deposition Modelling ◽  
Layer Height ◽  
Fused Deposition ◽  
3D Printed ◽  
Shear Area

Carbon fibre-reinforced materials are becoming more and more popular in various fields of industries because of their lightweight and perfect mechanical properties. Additive manufacturing technologies can be used for the production of complex parts from various materials including composites. Fused deposition modelling (FDM) is an excellent technology for the production of composite structures reinforced with short or continuous carbon fibre. In this study, modified FDM technology was used for the production of composites reinforced with continuous carbon fibre. The main aim of this study is to evaluate the shear strength of 3D-printed composite structures. The influence of printing layer height and line width on shear strength was analysed. Results showed that layer height has a significant influence on shear strength, while the influence of printing line width on shear strength is slightly smaller. Reduction of layer height from 0.4 mm to 0.3 mm allows increasing shear strength by about 40 percent. Moreover, the influence of the shear area and overlap length on shear force showed linear dependency, in which the shear area is increasing the shear force increasing proportionally. Finally, the results obtained can be used for the design and development of new 3D-printed composite structures.

scholarly journals Effect of Sanding and Plasma Treatment of 3D-Printed Parts on Bonding to Wood with PVAc Adhesive

Polymers ◽  
2021 ◽  
Vol 13 (8) ◽  
pp. 1211
Author(s):  
Mirko Kariž ◽  
Daša Krapež Tomec ◽  
Sebastian Dahle ◽  
Manja Kitek Kuzman ◽  
Milan Šernek ◽  
...  
Keyword(s):  
Shear Strength ◽  
Plasma Treatment ◽  
Polylactic Acid ◽  
Wood Flour ◽  
Surface Preparation ◽  
Contact Angles ◽  
Fused Deposition Modelling ◽  
Water Contact ◽  
Fused Deposition ◽  
3D Printed

Additive manufacturing is becoming increasingly important for manufacturing end products, not just prototyping. However, the size of 3D-printed products is limited due to available printer sizes and other technological limitations. For example, making furniture from 3D-printed parts and wooden elements requires adequate adhesive joints. Since materials for 3D printing usually do not bond very well with adhesives designed for woodworking, they require special surface preparation to improve adhesion. In this study, fused deposition modelling (FDM) 3D-printed parts made of polylactic acid (PLA), polylactic acid with wood flour additive (Wood-PLA), and acrylonitrile-butadiene-styrene (ABS) polymers were bonded to wood with polyvinyl acetate (PVAc) adhesive. The surfaces of the samples were bonded as either non-treated, sanded, plasma treated, or sanded and plasma treated to evaluate the effect of each surface preparation on the bondability of the 3D-printed surfaces. Different surface preparations affected the bond shear strength in different ways. The plasma treatment significantly reduced water contact angles on all tested printing materials and increased the bond tensile shear strength of the adhesive used. The increase in bond strength was highest for the surfaces that had been both sanded and plasma treated. The highest increase was found for the ABS material (untreated 0.05 MPa; sanded and plasma treated 4.83 MPa) followed by Wood-PLA (from 0.45 MPa to 3.96 MPa) and PLA (from 0.55 MPa to 3.72 MPa). Analysis with a scanning electron microscope showed the smooth surfaces of the 3D-printed parts, which became rougher with sanding with more protruded particles, but plasma treatment partially melted the surface structures on the thermoplastic polymer surfaces.

scholarly journals Influence of the Infill Geometry of 3D-Printed Tablets on Drug Dissolution

2021 ◽  
Vol 5 (1) ◽  
pp. 15
Author(s):  
Nuno Venâncio ◽  
Gabriela G. Pereira ◽  
João F. Pinto ◽  
Ana I. Fernandes
Keyword(s):  
Three Dimensional ◽  
Drug Dissolution ◽  
Fused Deposition Modelling ◽  
Three Dimensional Printing ◽  
Preliminary Results ◽  
Fused Deposition ◽  
3D Printed ◽  
Dimensional Printing ◽  
Hot Melt ◽  
Patient Centric

Patient-centric therapy is especially important in pediatrics and may be attained by three-dimensional printing. Filaments containing 30% w/w of theophylline were produced by hot-melt extrusion and printed using fused deposition modelling to produce tablets. Here, preliminary results evaluating the effect of infill geometry (cross, star, grid) on drug content and release are reported.

Investigations of process parameters during dissolution studies of drug loaded 3D printed tablets

2021 ◽  
pp. 095441192199358
Author(s):  
Varun Sharma ◽  
Khaja Moinuddin Shaik ◽  
Archita Choudhury ◽  
Pramod Kumar ◽  
Prateek Kala ◽  
...  
Keyword(s):  
Dissolution Rate ◽  
Process Parameters ◽  
Empirical Relation ◽  
Three Dimensional ◽  
Critical Parameters ◽  
Fused Deposition Modelling ◽  
Fused Deposition ◽  
Rate Of Dissolution ◽  
3D Printed ◽  
Percentage Release

The present research paper attempts to study the effect of different process parameters on the dissolution rate during 3D printed tablets. Three-dimensional printing has the potential of serving tailored made tablets to cater personalized drug delivery systems. Fluorescein loaded PVA filaments through impregnation route was used to fabricate tablets based on Taguchi based design of experimentation using Fused Deposition Modelling (FDM). The effect of print speed, infill percentage and layer thickness were analyzed to study the effect on rate of dissolution. Infill percentage followed by print speed were found to be critical parameters affecting dissolution rate. The data analysis provided an insight into the study of interaction among different 3D printing parameters to develop an empirical relation for percentage release of the drug in human body.

Effect of heat treatment on mechanical properties of 3D printed polylactic acid parts

2021 ◽  
Vol 63 (1) ◽  
pp. 73-78
Author(s):  
Pulkin Gupta ◽  
Sudha Kumari ◽  
Abhishek Gupta ◽  
Ankit Kumar Sinha ◽  
Prashant Jindal
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Polylactic Acid ◽  
Recrystallization Temperature ◽  
Fused Deposition Modelling ◽  
Fused Deposition ◽  
Dog Bone ◽  
Heat Treated ◽  
Maximum Decrease ◽  
3D Printed

Abstract Fused deposition modelling (FDM) is a layer-by-layer manufacturing process type of 3D-printing (3DP). Significant variation in the mechanical properties of 3D printed specimens is observed because of varied process parameters and interfacial bonding between consecutive layers. This study investigates the influence of heat treatment on the mechanical strength of FDM 3D printed Polylactic acid (PLA) parts with constant 3DP parameters and ambient conditions. To meet the objectives, 7 sets, each containing 5 dog-bone shaped samples, were fabricated from commercially available PLA filament. Each set was subjected to heat treatment at a particular temperature for 1 h and cooled in the furnace itself, while one set was left un-treated. The temperature for heat treatment (Th) varied from 30 °C to 130 °C with increments of 10 °C. The heat-treated samples were characterized under tensile loading of 400 N and mechanical properties like Young’s modulus (E), Strain % ( ε ) and Stiffness (k) were evaluated. On comparing the mechanical properties of heat-treated samples to un-treated samples, significant improvements were observed. Heat treatment also altered the geometries of the samples. Mechanical properties improved by 4.88 % to 10.26 % with the maximum being at Th of 110 °C and below recrystallization temperature (Tr) of 65 °C. Deformations also decreased significantly at higher temperatures above 100 °C, by a maximum of 36.06 %. The dimensions of samples showed a maximum decrease of 1.08 % in Tr range and a maximum decrease of 0.31 % in weight at the same temperature. This study aims to benefit the society by establishing suitable Th to recover the lost strength in PLA based FDM 3D printed parts.

scholarly journals Strength Comparison of FDM 3D Printed PLA Made by Different Manufacturers

TEM Journal ◽  
2020 ◽  
pp. 966-970
Author(s):  
Damir Hodžić ◽  
Adi Pandžić ◽  
Ismar Hajro ◽  
Petar Tasić
Keyword(s):  
Experimental Study ◽  
Additive Manufacturing ◽  
Fused Deposition Modelling ◽  
Fused Deposition ◽  
Manufacturing Technique ◽  
Plastic Materials ◽  
Wide Range ◽  
3D Printed ◽  
The Difference ◽  
Printing Parameters

Widely used additive manufacturing technique for plastic materials is Fused Deposition Modelling (FDM). The FDM technology has gained interest in industry for a wide range of applications, especially today when large number of different materials on the market are available. There are many different manufacturers for the same FDM material where the difference in price goes up to 50%. This experimental study investigates possible difference in strength of the 3D printed PLA material of five different manufacturers. All specimens are 3D printed on Ultimaker S5 printer with the same printing parameters, and they are all the same colour.

scholarly journals 3D Printing of Thermo-Sensitive Drugs

Pharmaceutics ◽  
2021 ◽  
Vol 13 (9) ◽  
pp. 1524
Author(s):  
Sadikalmahdi Abdella ◽  
Souha H. Youssef ◽  
Franklin Afinjuomo ◽  
Yunmei Song ◽  
Paris Fouladian ◽  
...  
Keyword(s):  
3D Printing ◽  
Three Dimensional ◽  
Fused Deposition Modelling ◽  
Future Directions ◽  
Digital Light Processing ◽  
Fused Deposition ◽  
Printing Technique ◽  
3D Printed ◽  
Semi Solid ◽  
Selection Of

Three-dimensional (3D) printing is among the rapidly evolving technologies with applications in many sectors. The pharmaceutical industry is no exception, and the approval of the first 3D-printed tablet (Spiratam®) marked a revolution in the field. Several studies reported the fabrication of different dosage forms using a range of 3D printing techniques. Thermosensitive drugs compose a considerable segment of available medications in the market requiring strict temperature control during processing to ensure their efficacy and safety. Heating involved in some of the 3D printing technologies raises concerns regarding the feasibility of the techniques for printing thermolabile drugs. Studies reported that semi-solid extrusion (SSE) is the commonly used printing technique to fabricate thermosensitive drugs. Digital light processing (DLP), binder jetting (BJ), and stereolithography (SLA) can also be used for the fabrication of thermosensitive drugs as they do not involve heating elements. Nonetheless, degradation of some drugs by light source used in the techniques was reported. Interestingly, fused deposition modelling (FDM) coupled with filling techniques offered protection against thermal degradation. Concepts such as selection of low melting point polymers, adjustment of printing parameters, and coupling of more than one printing technique were exploited in printing thermosensitive drugs. This systematic review presents challenges, 3DP procedures, and future directions of 3D printing of thermo-sensitive formulations.

Use of polymer concrete for large-scale 3D printing

2021 ◽  
Vol 27 (3) ◽  
pp. 465-474
Author(s):  
Martin Krčma ◽  
David Škaroupka ◽  
Petr Vosynek ◽  
Tomáš Zikmund ◽  
Jozef Kaiser ◽  
...  
Keyword(s):  
3D Printing ◽  
Large Scale ◽  
Mechanical Performance ◽  
Construction Material ◽  
Polymer Concrete ◽  
Fused Deposition Modelling ◽  
Cast State ◽  
Content Type ◽  
Fused Deposition ◽  
3D Printed

Purpose This paper aims to focus on the evaluation of a polymer concrete as a three-dimensional (3D) printing material. An associated company has developed plastic concrete made from reused unrecyclable plastic waste. Its intended use is as a construction material. Design/methodology/approach The concrete mix, called PolyBet, composed of polypropylene and glass sand, is printed by the fused deposition modelling process. The process of material and parameter selection is described. The mechanical properties of the filled material were compared to its cast state. Samples were made from castings and two different orientations of 3D-printed parts. Three-point flex tests were carried out, and the area of the break was examined. Computed tomography of the samples was carried out. Findings The influence of the 3D printing process on the material was evaluated. The mechanical performance of the longitudinal samples was close to the cast state. There was a difference in the failure mode between the states, with cast parts exhibiting a tougher behaviour, with fractures propagating in a stair-like manner. The 3D-printed samples exhibited high degrees of porosity. Originality/value The results suggest that the novel material is a good fit for 3D printing, with little to no degradation caused by the process. Layer adhesion was shown to be excellent, with negligible effect on the finished part for the longitudinal orientation. That means, if large-scale testing of buildability is successful, the material is a good fit for additive manufacturing of building components and other large-scale structures.

Photonic curing of silver paths on 3D printed polymer substrate

Circuit World ◽  
2019 ◽  
Vol 45 (1) ◽  
pp. 9-14
Author(s):  
Jakub Krzeminski ◽  
Bartosz Blicharz ◽  
Andrzej Skalski ◽  
Grzegorz Wroblewski ◽  
Małgorzata Jakubowska ◽  
...  
Keyword(s):  
Polymer Substrate ◽  
Fused Deposition Modelling ◽  
Content Type ◽  
Fused Deposition ◽  
Photonic Curing ◽  
Structural Electronics ◽  
Jet Printing ◽  
3D Printed ◽  
Aerosol Jet Printing ◽  
Photonic Sintering

Purpose Despite almost limitless possibilities of rapid prototyping, the idea of 3D printed fully functional electronic device still has not been fulfilled – the missing point is a highly conductive material suitable for this technique. The purpose of this paper is to present the usage of the photonic curing process for sintering highly conductive paths printed on the polymer substrate. Design/methodology/approach This paper evaluates two photonic curing processes for the conductive network formulation during the additive manufacturing process. Along with the xenon flash sintering for aerosol jet-printed paths, this paper examines rapid infrared sintering for thick-film and direct write techniques. Findings This paper proves that the combination of fused deposition modeling, aerosol jet printing or paste deposition, along with photonic sintering, is suitable to obtain elements with low resistivity of 3,75·10−8 Ωm. Presented outcomes suggest the solution for fabrication of the structural electronics systems for daily-use applications. Originality/value The combination of fused deposition modelling (FDM) and aerosol jet printing or paste deposition used with photonic sintering process can fill the missing point for highly conductive materials for structural electronics.

Sign in / Sign up

Export Citation Format

Share Document