scholarly journals Biomedical PEVA Nanocomposite with Dual Clay Nanofiller: Cytotoxicity, Mechanical Properties, and Biostability

Polymers ◽  
2021 ◽  
Vol 13 (24) ◽  
pp. 4345
Author(s):  
Tuty Fareyhynn Mohammed Fitri ◽  
Azlin Fazlina Osman ◽  
Eid M. Alosime ◽  
Rahimah Othman ◽  
Fatimah Hashim ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Tensile Test ◽  
Test Data ◽  
Basal Spacing ◽  
Physical Treatment ◽  
Surface Degradation ◽  
Morphological Studies ◽  
Tensile Test Data

Poly(ethylene-vinyl acetate) (PEVA) nanocomposite incorporating dual clay nanofiller (DCN) of surface modified montmorillonite (S-MMT) and bentonite (Bent) was studied for biomedical applications. In order to overcome agglomeration of the DCN, the S-MMT and Bent were subjected to a physical treatment prior to being mixed with the copolymer to form nanocomposite material. The S-MMT and Bent were physically treated to become S-MMT(P) and Bent(pH-s), respectively, that could be more readily dispersed in the copolymer matrix due to increments in their basal spacing and loosening of their tactoid structure. The biocompatibility of both nanofillers was assessed through a fibroblast cell cytotoxicity assay. The mechanical properties of the neat PEVA, PEVA nanocomposites, and PEVA-DCN nanocomposites were evaluated using a tensile test for determining the best S-MMT(P):Bent(pH-s) ratio. The results were supported by morphological studies by transmission electron microscopy (TEM) and scanning electron microscopy (SEM). Biostability evaluation of the samples was conducted by comparing the ambient tensile test data with the in vitro tensile test data (after being immersed in simulated body fluid at 37 °C for 3 months). The results were supported by surface degradation analysis. Our results indicate that the cytotoxicity level of both nanofillers reduced upon the physical treatment process, making them safe to be used in low concentration as dual nanofillers in the PEVA-DCN nanocomposite. The results of tensile testing, SEM, and TEM proved that the ratio of 4:1 (S-MMT(P):Bent(pH-s)) provides a greater enhancement in the mechanical properties of the PEVA matrix. The biostability assessment indicated that the PEVA-DCN nanocomposite can achieve much better retention in tensile strength after being subjected to the simulated physiological fluid for 3 months with less surface degradation effect. These findings signify the potential of the S-MMT(P)/Bent(pH-s) as a reinforcing DCN, with simultaneous function as biostabilizing agent to the PEVA copolymer for implant application.

Design resistance of helical seam pipe columns with limited tensile test data

2021 ◽  
Vol 183 ◽  
pp. 106724
Author(s):  
Won-Hee Kang ◽  
Stephen J. Hicks ◽  
Brian Uy ◽  
Farhad Aslani
Keyword(s):  
Tensile Test ◽  
Test Data ◽  
Design Resistance ◽  
Tensile Test Data

Constitutive Modeling of Biaxial Mechanical Response of Arteries Subjected to Gradual Elastin Degradation

2013 ◽  
Author(s):  
Shahrokh Zeinali-Davarani ◽  
Ming-Jay Chow ◽  
Raphaël Turcotte ◽  
Katherine Yanhang Zhang
Keyword(s):  
Tensile Test ◽  
Mechanical Behavior ◽  
Test Data ◽  
Constitutive Modeling ◽  
Mechanical Response ◽  
Collagen Fibers ◽  
Biaxial Tensile Test ◽  
Elastin Degradation ◽  
Adaptive Processes ◽  
Tensile Test Data

The passive mechanical response of arteries is believed to be mainly dominated by elastin and collagen fibers. Many arterial diseases are accompanied by significant changes in quantity and as well as the microstructure of these constituents due to the mechanical and biological adaptive processes. In this study we focus on the biaxial tensile test data of elastase-treated porcine aortic tissues [1]. We study the mechanical behavior of aortic tissues under gradual elastin degradation through constitutive modeling and associate the mechanical response with the microstructure of collagen observed in the microscopic images of fresh and digested tissues.

scholarly journals Enhancement of Mechanical and Thermal Properties of Polylactic Acid/Polycaprolactone Blends by Hydrophilic Nanoclay

2013 ◽  
Vol 2013 ◽  
pp. 1-11 ◽  
Author(s):  
Chern Chiet Eng ◽  
Nor Azowa Ibrahim ◽  
Norhazlin Zainuddin ◽  
Hidayah Ariffin ◽  
Wan Md. Zin Wan Yunus ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Polylactic Acid ◽  
Mechanical Analysis ◽  
Basal Spacing ◽  
Mechanical And Thermal Properties ◽  
X Ray Diffraction ◽  
Transmission Electron ◽  
The Matrix ◽  
Thermal Stability Of

The effects of hydrophilic nanoclay, Nanomer PGV, on mechanical properties of Polylactic Acid (PLA)/Polycaprolactone (PCL) blends were investigated and compared with hydrophobic clay, Montmorillonite K10. The PLA/PCL/clay composites were prepared by melt intercalation technique and the composites were characterized by X-ray Diffraction (XRD), Fourier Transform Infrared Spectroscopy (FTIR), Thermogravimetric Analysis (TGA), Dynamic Mechanical Analysis (DMA), Scanning Electron Microscopy (SEM), and Transmission Electron Microscopy (TEM). FTIR spectra indicated that formation of hydrogen bond between hydrophilic clay with the matrix. XRD results show that shifting of basal spacing when clay incorporated into polymer matrix. TEM micrographs reveal the formation of agglomerate in the composites. Based on mechanical properties results, addition of clay Nanomer PGV significantly enhances the flexibility of PLA/PCL blends about 136.26%. TGA showed that the presence of clay improve thermal stability of blends. DMA show the addition of clay increase storage modulus and the presence of clay Nanomer PGV slightly shift two Tg of blends become closer suggest that the presence of clay slightly compatibilizer the PLA/PCL blends. SEM micrographs revealed that presence of Nanomer PGV in blends influence the miscibility of the blends. The PLA/PCL blends become more homogeneous and consist of single phase morphology.

Effect of Nanocellulose Loading on Tensile Properties of Nitrile Rubber

2017 ◽  
Vol 264 ◽  
pp. 112-115
Author(s):  
Erfan Suryani Abdul Rashid ◽  
Wageeh Abdulhadi Yehye ◽  
Nurhidayatullaili Muhd Julkapli ◽  
Sharifah Bee O.A. Abdul Hamid
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Scanning Electron Microscopy ◽  
Tensile Strength ◽  
Tensile Test ◽  
Tensile Properties ◽  
Mechanical Performance ◽  
Butadiene Rubber ◽  
Fracture Surfaces ◽  
Scanning Electron

Nanocellulose (NCC) is incorporated into nitrile butadiene rubber (NBR) latex with the composition 0 to 5 phr using dipping method. Mechanical properties of NBR/NCC composites using tensile test was used to characterize their mechanical performance and the fracture surfaces post tensile test were studied. The tensile strength of NBR/NCC composites increase significantly with the addition of nanocellulose. This could be anticipated due to the presence of Van der Waals interaction between hydrophilic natures of nanocellulose with hydrophobic of NBR consequently limits the tearing propagation. The result was supported with the fracture surfaces morphology viewed under Fourier Emission Scanning Electron Microscopy (FESEM).

scholarly journals Enhancement the Osseo Integration Properties of Polymer for Human Body Implants

2020 ◽  
Vol 23 (4) ◽  
pp. 331-337
Author(s):  
Dhurgham Majid Rasheed ◽  
Dunya Abdulsahib Hamdi
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Scanning Electron Microscopy ◽  
Grain Boundaries ◽  
Mechanical Performance ◽  
Wear Test ◽  
High Energy ◽  
In Vitro Test ◽  
Scanning Electron

In this research, polymer polymethyl methacrylate PMMA composite with nano ceramic Zr and HAp material were used to manufacture one part of the implant system (femoral ball head of hip implant). Three set of hybrid materials were fabricated and tested for this study; the first mixtures which contains 100% (PMMA), the second mixtures which contains (90% (PMMA) + 8% (Zr) + 2% (HAp)), and the third mixtures which contains (80% (PMMA) + 18% (Zr) + 2% (HAp)) were investigated. The mechanical properties for these mixtures increased with the increasing of nano ceramic concentration (Zr and HAp) composite material in the polymer compared to pure polymer PMMA sample. However, an increase in the concentration of Zr from 8% to 18% content cause a considerable decrease of the hardness where a drop of homogeneity in Zr- matrix PMMA contact occurred, V Hardness value are (68 ,80 and 70) Kg.mm for three mixture respectively. The wear test was in agreement with results of the hardness test. The weight loss of the above samples of the wear test were (0.041, 0.035 and 0.037) respectively. According to mechanical properties, the best sample contains (90% (PMMA) + 8% (Zr) + 2% (HAp)). The Scanning electron microscopy resolute showed the particles forming semi-continuous network along grain boundaries polymer for second sample mixtures containing (90% (PMMA) + 8% (Zr) + 2% (HAp)), provides a low atomic packing and high energy. This will make the grain boundaries more reactive and strengthen mechanical performance. The Optical microscopy, Scanning electron microscopy and Xray spectroscopy analysis for In vitro test using SBF shows the growth of HAp layer with an increase in concentration of Ca and P elements formed on the surface of the second sample. This display of good results is a proof of the biocompatibility of the polymer sample.

Goodness-of-Fit of the Ramberg-Osgood Analytic Stress-Strain Curve to Tensile Test Data

1982 ◽  
Vol 10 (6) ◽  
pp. 263 ◽  
Author(s):  
R Horstman ◽  
KA Peters ◽  
RL Meltzer ◽  
M Bruce Vieth ◽  
R Papirno
Keyword(s):  
Tensile Test ◽  
Test Data ◽  
Goodness Of Fit ◽  
Strain Curve ◽  
Stress Strain Curve ◽  
Stress Strain ◽  
Tensile Test Data

scholarly journals Fabrication, Mechanical Properties and In-Vitro Behavior of Akermanite Bioceramic

Materials ◽  
2020 ◽  
Vol 13 (21) ◽  
pp. 4887
Author(s):  
Fariborz Tavangarian ◽  
Caleb A. Zolko ◽  
Sorour Sadeghzade ◽  
Marwan Fayed ◽  
Keivan Davami
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Subsequent Annealing ◽  
Apatite Formation ◽  
X Ray ◽  
Transmission Electron ◽  
Powder Samples ◽  
Sbf Solution ◽  
Scanning Electron

Pure nanocrystalline akermanite (Ca2MgSi2O7) powder was synthesized by mechanical activation with subsequent annealing of talc, calcium carbonate, and silicate powders as the initial materials. Powder samples were characterized by X-ray diffractometry (XRD), scanning electron microscopy (SEM), thermogravimetric analysis (TGA), and transmission electron microscopy (TEM) techniques. The results showed that pure nanocrystalline akermanite with a crystalline size of 35 nm was synthesized after ball milling the initial powders for 20 h with subsequent annealing at 900 °C for 1 h. Mechanical properties of bulk akermanite samples were studied as well. The results showed that the produced akermanite tablets sintered at 1200 °C for 5 h had a Young’s modulus of 3800 MPa, an ultimate compressive strength of 24.7 MPa, and a density of 2.489 g/cm3. The in-vitro behavior of the produced akermanite was evaluated by soaking the samples in an SBF solution. The results showed that the produced akermanite had the apatite formation ability on its surface and can be a good candidate for bone tissue engineering applications.

Sign in / Sign up

Export Citation Format

Share Document