scholarly journals Natural Frequency Sensitivity Analysis of Fire-Fighting Jet System with Adaptive Gun Head

Processes ◽  
2019 ◽  
Vol 7 (11) ◽  
pp. 808 ◽  
Author(s):  
Xiaoming Yuan ◽  
Xuan Zhu ◽  
Chu Wang ◽  
Lijie Zhang ◽  
Yong Zhu
Keyword(s):  
Sensitivity Analysis ◽  
Natural Frequency ◽  
Natural Frequencies ◽  
Fire Fighting ◽  
Mode Analysis ◽  
Mode Shapes ◽  
Design Parameters ◽  
Parameter Method ◽  
First Order ◽  
Typical Design

The gun head is the end effector of the fire-fighting jet system. Compared with a traditional fixed gun head, an adaptive gun head has the advantages of having an adjustable nozzle opening, a wide applicable flow range, and a high fire-extinguishing efficiency. Thus, the adaptive gun head can extinguish large fires quickly and efficiently. The fire-fighting jet system with an adaptive gun head has fluid-structure interaction and discrete-continuous coupling characteristics, and the influence of key design parameters on its natural frequencies needs to be determined by a sensitivity analysis. In this paper, the dynamic model and equations of the jet system were established based on the lumped parameter method, and the sensitivity calculation formulas of the natural frequency of the jet system to typical design parameters were derived. Natural frequencies and mode shapes of the jet system were determined based on a mode analysis. The variation law of the sensitivity of the natural frequency of the jet system to typical design parameters was revealed by the sensitivity analysis. The results show that the fluid mass inside the spray core within a certain initial gas content is the most important factor affecting the natural frequency of the jet system. There was only a 0.51% error between the value of the first-order natural frequency of the jet system determined by the modal experiment and the theoretical one, showing that good agreement with the first-order natural frequency of the jet system was found. This paper provides a theoretical basis for the dynamic optimization design of the adaptive gun head of the fire water monitor.

scholarly journals Analysis of Free Vibration of Hydraulic Opposing Cylinder Controlled by Servo Valve

2021 ◽  
Author(s):  
Xiaoming Yuan ◽  
Weiqi Wang ◽  
Xuan Zhu ◽  
Bing Du ◽  
Lijie Zhang
Keyword(s):  
Free Vibration ◽  
Natural Frequency ◽  
Natural Frequencies ◽  
Transmission System ◽  
Normal Operation ◽  
Design Parameters ◽  
Analytical Relationship ◽  
Parameter Method ◽  
Mechanical Transmission ◽  
Servo Valve

Abstract The fluid transmission medium has large compressibility and low rigidity, and its physical properties are extremely sensitive to state parameters such as flow, pressure and temperature. Therefore, compared with the mechanical transmission system, the natural frequency of the fluid transmission system is relatively low and has time-varying characteristics. After a wide frequency range changing of the load frequency and long-term operation, the excitation frequency of the fluid transmission system is more likely to approach its natural frequency and causes resonance, which seriously affects the normal operation of the system. Therefore, taking the hydraulic opposing cylinder controlled by servo valve as the research object, based on the analytical relationship between the dynamic bulk modulus and the equivalent stiffness of oil, the vibration dynamics models and equations of the system is established by using the lumped parameter method. Through the free vibration analysis, the natural frequencies and main vibration modes of the system are determined and the sensitivity changes of the natural frequencies to the design parameters are revealed. The maximum error between the theoretical modal frequency and the experimental one is 3.77%, which verifies the correctness of the dynamic model of the system. This research can provide a theoretical reference for the optimization of the dynamic performance of the hydraulic transmission system.

scholarly journals The approximate calculation of the natural frequencies of a Stockbridge type vibration damper and analysis of natural frequencies' sensitivity to the structural parameters

2021 ◽  
Vol 12 (2) ◽  
pp. 863-873
Author(s):  
Qing Yin ◽  
Jianli Zhao ◽  
Yong Liu ◽  
Yisheng Zhang
Keyword(s):  
Sensitivity Analysis ◽  
Approximate Calculation ◽  
Natural Frequencies ◽  
Second Order ◽  
Design Parameters ◽  
Gyration Radius ◽  
Vibration Damper ◽  
First Order ◽  
Highly Sensitive ◽  
Eccentric Distance

Abstract. Vibration damper is widely used in overhead transmission lines to alleviate aeolian vibration. Its natural frequencies are important parameters for a vibration damper. In this paper, the approximate calculation formulas of natural frequencies of the one-side subsystem of a Stockbridge type vibration damper were derived and the design sensitivity analysis of the natural frequencies was studied using partial differential equations with respect to each concerned parameter including the length of the steel strand, the mass of the counterweight, the eccentric distance, and the radius of gyration of the counterweight. Through a case study that considered a variation of up to ±30 % in the values of the design parameters, the exact calculation and approximate calculation results of the natural frequencies were analysed, and the sensitivity of the vibration damper's natural frequencies to the design parameters was studied. The results show that, within the range of the parameters used in this study, the approximately calculated first-order frequency is lower than the exact values, whereas the approximately calculated second-order frequency is larger than the exact values. The sensitivity analysis indicates that the first-order frequency is highly sensitive to the steel strand's length, whereas it is moderately sensitive to the counterweight's mass and slightly sensitive to the eccentric distance and the gyration radius of the counterweight; the second-order frequency is highly sensitive to the steel strand's length and the gyration radius of the counterweight, moderately sensitive to the counterweight's mass, and slightly sensitive to the eccentric distance. It will provide theoretical guidance and approximate analysis method in engineering for the design of the vibration damper.

scholarly journals Effects of Elliptical Hole on the Correlation of Natural Frequency with Buckling Load of Basalt Laminates Composite Plates

2020 ◽  
Vol 27 (1) ◽  
pp. 216-225
Author(s):  
Buntheng Chhorn ◽  
WooYoung Jung
Keyword(s):  
Free Vibration ◽  
Natural Frequency ◽  
Natural Frequencies ◽  
Basalt Fiber ◽  
Orientation Angle ◽  
Elliptical Hole ◽  
Composite Plates ◽  
Buckling Load ◽  
Mode Shapes ◽  
Geometric Ratio

AbstractRecently, basalt fiber reinforced polymer (BFRP) is acknowledged as an outstanding material for the strengthening of existing concrete structure, especially it was being used in marine vehicles, aerospace, automotive and nuclear engineering. Most of the structures were subjected to severe dynamic loading during their service life that may induce vibration of the structures. However, free vibration studied on the basalt laminates composite plates with elliptical cut-out and correlation of natural frequency with buckling load has been very limited. Therefore, effects of the elliptical hole on the natural frequency of basalt/epoxy composite plates was performed in this study. Effects of stacking sequence (θ), elliptical hole inclination (ϕ), hole geometric ratio (a/b) and position of the elliptical hole were considered. The numerical modeling of free vibration analysis was based on the mechanical properties of BFRP obtained from the experiment. The natural frequencies as well as mode shapes of basalt laminates composite plates were numerically determined using the commercial program software (ABAQUS). Then, the determination of correlation of natural frequencies with buckling load was carried out. Results showed that elliptical hole inclination and fiber orientation angle induced the inverse proportion between natural frequency and buckling load.

Vibration of Beams with a Single Delamination under Axial Loading

2011 ◽  
Vol 675-677 ◽  
pp. 477-480
Author(s):  
Dong Wei Shu
Keyword(s):  
Free Vibration ◽  
Natural Frequency ◽  
Analytical Solutions ◽  
Axial Load ◽  
Natural Frequencies ◽  
Axial Loading ◽  
Composite Beams ◽  
Mode Shapes ◽  
Equilibrium Conditions ◽  
Monotonic Relation

In this work analytical solutions are developed to study the free vibration of composite beams under axial loading. The beam with a single delamination is modeled as four interconnected Euler-Bernoulli beams using the delamination as their boundary. The continuity and the equilibrium conditions are satisfied between the adjoining beams. The studies show that the sizes and the locations of the delaminations significantly influence the natural frequencies and mode shapes of the beam. A monotonic relation between the natural frequency and the axial load is predicted.

Split Vibration Modes in Acoustically-Coupled Disk Stacks

1995 ◽  
Author(s):  
Jung-Ge Tseng ◽  
Jonathan Wickert
Keyword(s):  
Natural Frequencies ◽  
Three Dimensional ◽  
System Level ◽  
Thin Plates ◽  
Mode Shapes ◽  
Design Parameters ◽  
Phase System ◽  
Acoustic Coupling ◽  
Annular Plates ◽  
Vibration Model

Abstract Vibration of an array of stacked annular plates, in which adjacent plates couple weakly through an acoustic layer, is investigated through experimental and theoretical methods. Such acoustic coupling manifests itself through split natural frequencies, beating in the time responses of adjacent or separated plates, and system-level modes in which plates in the array vibrate in- or out-of-phase at closely-spaced frequencies. Laboratory measurements, including a technique in which the frequency response function of all in-phase modes but no out-of-phase modes, or visa versa, is measured, demonstrate the contribution of coupling to the natural frequency spectrum, and identify the combinations of design parameters for which it is important. For the lower modes of primary interest here, the natural frequencies of the out-of-phase system modes decrease as the air layer becomes thinner, while those of the in-phase mode remain sensibly constant at the in vacuo values. A vibration model comprising N classical thin plates that couple through the three-dimensional acoustic fields established in the annular cavities between plates is developed, and its results are compared with measurements of the natural frequencies and mode shapes.

A Note on the Lowest Natural Frequency of a Square Plate Point-Supported at the Corners

1962 ◽  
Vol 66 (616) ◽  
pp. 240-241 ◽  
Author(s):  
C. L. Kirk
Keyword(s):  
Natural Frequency ◽  
Natural Frequencies ◽  
Present Note ◽  
Flexural Vibration ◽  
Approximate Solutions ◽  
Mode Shapes ◽  
Electronic Digital Computer ◽  
Isotropic Plates ◽  
Four Corners ◽  
Square Plate

Recently Cox and Boxer determined natural frequencies and mode shapes of flexural vibration of uniform rectangular isotropic plates, that have free edges and pinpoint supports at the four corners. In their analysis, they obtain approximate solutions of the differential equation through the use of finite difference expressions and an electronic digital computer. In the present note, the frequency expression and mode shape for a square plate, vibrating at the lowest natural frequency, are determined by considerations of energy. The values obtained are compared with those given in reference.

A Vibrational Mode Analysis of Free Finite-Length Thick Cylinders Using the Finite Element Method

1998 ◽  
Vol 120 (2) ◽  
pp. 371-377 ◽  
Author(s):  
Huan Wang ◽  
Keith Williams ◽  
Wei Guan
Keyword(s):  
Finite Length ◽  
Natural Frequencies ◽  
Three Dimensional ◽  
Mode Analysis ◽  
Mode Shapes ◽  
Vibrational Modes ◽  
The Finite Element Method ◽  
Cylinder Length ◽  
Radial Thickness ◽  
Thick Cylinder

Based on their three-dimensional mode shapes, the vibrational modes of free finite length thick cylinders can be classified into 6 categories, consisting of pure radial, radial motion with radial shearing, extensional, circumferential, axial bending, and global modes. This classification, together with the numbers of both the circumferential and the longitudinal nodes, is sufficient to identify each mode of a finite length thick cylinder. The mode classification was verified experimentally by measurements on a thick cylinder. According to the displacement distribution ratio in the radial, tangential and longitudinal directions, the effect of varying cylinder length on the vibrational modes is such that all the modes can be broadly categorized as either pure radial modes, or non pure radial modes. The natural frequencies and mode shapes of the former are dependent upon only the radial dimensions of the models, while the natural frequencies and mode shapes of the latter are dependent upon both the axial length and radial thickness.

scholarly journals High-Fidelity Sensitivity Analysis of Modal Properties of Mistuned Bladed Disks Regarding Material Anisotropy

2018 ◽  
Author(s):  
Adam Koscso ◽  
Guido Dhondt ◽  
E. P. Petrov
Keyword(s):  
Sensitivity Analysis ◽  
Finite Element ◽  
Natural Frequencies ◽  
Mode Shapes ◽  
Finite Element Models ◽  
Coordinate Systems ◽  
Bladed Disks ◽  
Bladed Disk ◽  
Material Orientation

A new method has been developed for sensitivity calculations of modal characteristics of bladed disks made of anisotropic materials. The method allows the determination of the sensitivity of the natural frequencies and mode shapes of mistuned bladed disks with respect to anisotropy angles that define the crystal orientation of the monocrystalline blades using full-scale finite element models. An enhanced method is proposed to provide high accuracy for the sensitivity analysis of mode shapes. An approach has also been developed for transforming the modal sensitivities to coordinate systems used in industry for description of the blade anisotropy orientations. The capabilities of the developed methods are demonstrated on examples of a single blade and a mistuned realistic bladed disk finite element models. The modal sensitivity of mistuned bladed disks to anisotropic material orientation is thoroughly studied.

scholarly journals Vibrational Analysis on Hemp and Okra Fibres Mixed Glass Fiber Polyester Composite

2021 ◽  
Vol 8 (11) ◽  
pp. 55-62
Author(s):  
Putti Venkata Siva Teja ◽  
Badatala Ooha ◽  
Kondeti Sravanth
Keyword(s):  
Glass Fiber ◽  
Natural Frequency ◽  
Natural Frequencies ◽  
Fiber Composite ◽  
Fem Analysis ◽  
Vibration Characteristics ◽  
Mode Shapes ◽  
Machine Component ◽  
Free System ◽  
Glass Fiber Composite

In transverse vibrations the element moves to and fro in a direction perpendicular to the direction of the advance of the wave. To determine the vibration characteristics i.e., natural frequencies and mode shapes, modal analysis is a process for a structure or a machine component while is being designed. In real life, aero planes, missiles, rockets, space vehicles, satellites, sub marines etc are modeled as free-free mechanical systems. In this paper an attempt was made to compare natural frequency for two composite materials- ladies finger with Glass fiber composite and Hemp with Glass fiber composite by taking as cantilever beams. The cantilever beam which is fixed at one end is vibrated to obtain the natural frequency, mode shapes at four different modes. A simple low cost demonstration experiment is performed in this paper by using common apparatus in order to compare theoretical, numerical (FEM analysis) profiles of two free-free thin two rectangular composite beams of dimensions 305*49.5* 7 in mm. Keywords: Natural frequencies, Mode shapes, Vibration characteristics, Ladies finger fiber, Hemp fiber, Glass fiber, FEM analysis, Free-Free system.

scholarly journals Design optimization of vehicle asynchronous motors based on fractional harmonic response analysis

2021 ◽  
Vol 12 (1) ◽  
pp. 689-700
Author(s):  
Ao Lei ◽  
Chuan-Xue Song ◽  
Yu-Long Lei ◽  
Yao Fu
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Natural Frequency ◽  
Asynchronous Motor ◽  
Element Model ◽  
Design Parameters ◽  
Response Analysis ◽  
Harmonic Response ◽  
First Order ◽  
Harmonic Response Analysis

Abstract. To make vehicles more reliable and efficient, many researchers have tried to improve the rotor performance. Although certain achievements have been made, the previous finite element model did not reflect the historical process of the motor rotor well, and the rigidity and mass in rotor optimization are less discussed together. This paper firstly introduces fractional order into a finite element model to conduct the harmonic response analysis. Then, we propose an optimal design framework of a rotor. In the framework, objective functions of rigidity and mass are defined, and the relationship between high rigidity and the first-order frequency is discussed. In order to find the optimal values, an accelerated optimization method based on response surface (ARSO) is proposed to find the suitable design parameters of rigidity and mass. Because the higher rigidity can be transformed into the first-order natural frequency by objective function, this paper analyzes the first-order frequency and mass of a motor rotor in the experiment. The results proved that not only is the fractional model effective, but also the ARSO can optimize the rotor structure. The first-order natural frequency of asynchronous motor rotor is increased by 11.2 %, and the mass is reduced by 13.8 %, which can realize high stiffness and light mass of asynchronous motor rotors.

Sign in / Sign up

Export Citation Format

Share Document