scholarly journals Design of Respiration Rate Meter Using Flexible Sensor

2020 ◽  
Vol 2 (1) ◽  
pp. 13-18
Author(s):  
Sarah Aghnia Miyagi ◽  
Muhammad Ridha Mak’ruf ◽  
Endang Dian Setioningsih ◽  
Tark Das
Keyword(s):  
Respiratory Rate ◽  
Respiration Rate ◽  
Measurement Data ◽  
Average Error ◽  
Physiological Parameter ◽  
Left Chest ◽  
Chest Cavity ◽  
Measurement Results ◽  
The Right ◽  
Signal Conditioning Circuit

Respiration rate is an important physiological parameter that helps to provide important information about the patient's health status, especially from the human respiratory system. So it is necessary to measure the human respiratory rate by calculating the number of respiratory frequencies within 1 minute. The respiratory rate meter is a tool used to calculate the respiratory rate by counting the number of breaths for 1 minute. The author makes a tool to detect human respiratory rate by using a sensor that detects the ascend and descend of the chest cavity based on a microcontroller so that the operator can measure the breathing rate more practically and accurately. Component tool contains analog signal conditioning circuit and microcontroller circuit accompanied by display in the form of LCD TFT. The results of measurement data on 10 respondents obtained an average error value, namely the position of the right chest cavity 6.6%, middle chest cavity 7.92%, and left chest cavity 6.85%. This value is still below the error tolerance limit of 10%. It can be concluded that to obtain the best measurement results, the sensor is placed in the position of the right chest cavity.

scholarly journals Measuring Respiration Rate Via Android

2019 ◽  
Vol 1 (1) ◽  
pp. 20-26
Author(s):  
Shofiyah Shofiyah ◽  
I Dewa Gede Hari Wisana ◽  
Triwiyanto Triwiyanto ◽  
Sari Luthfiyah
Keyword(s):  
Respiratory Rate ◽  
Respiration Rate ◽  
Liquid Crystal Display ◽  
Human Stomach ◽  
Average Error ◽  
Breathing Cycle ◽  
Minimum Threshold ◽  
Minimum Error ◽  
Measurement Results ◽  
Flex Sensors

Abstract-Respiratory rate is the total number of breath or breathing cycle, which occurs every minute. Abnormal respiratory rate is a sensitive indicator for danger patients requiring medical treatment immediately. The objective of the study is to design respiration rate monitor via Anroid mobile phone. In this study, we used flex sensors to detect the respiration rate. The flex sensors was placed in the human stomach diaphragm which detects the changes in the human stomach diaphragm during breathing. The measurement results are displayed on the liquid crystal display (LCD) 2 x 16. The data  will be sent via a Bluetooth connection to the android to display the values ​​and graphs. The comparison between the design and standart showed that the maximum erros is 4.69% while the minimum error is 1.52%. The average error for all measurement is 2.83%. It can be concluded that the tool wear is eligible because it is still below the minimum threshold of 10% error.

scholarly journals Measuring Respiration Rate Based Android

2019 ◽  
Vol 1 (1) ◽  
pp. 39-44
Author(s):  
I Kadek Eman Giyana Mahardika ◽  
Torib Hamzah ◽  
Triana Rahmawati ◽  
Liliek Soetjiatie
Keyword(s):  
Respiratory Rate ◽  
Measurement Data ◽  
Average Error ◽  
Measurement Tool ◽  
Rate Measurement ◽  
The Media ◽  
Method Of Measurement ◽  
The Mind ◽  
Average Average

Respiratory rate measurement tool is a technique used to determine the number of respiratory activity a person every minute. In the classification of the number of breathing per minute someone, can be divided into three groups, namely the so-called eupnea/normal, above average breathing called tachypnea, while below the average so-called bradypnea. This method is highly dependent on the concentration of the mind and senses actor sensitivity measurement / observation. Therefore human nature is easy to forget, tired and bored, so now developed a method of measurement or observation of respiratory rate electronically. In this study, respiratory rate measurement making use flex sensor by placing the sensor in the patient's stomach and will detect the curvature of the patient's stomach. Results from the patient's respiratory displayed on the LCD Character and android using HC-05 Bluetooth as the media sender. The results of the measurement data of the 10 respondents indicated the average - average error of 3.2%. After testing and data collection can be concluded that the appliance is eligible to use because it is still within the tolerance range of 10%.

scholarly journals Nine Channel Temperature Data Logger in Measuring the Effectiveness of the Sterilization Process of Medical Instruments with Dry Sterilization

2021 ◽  
Vol 1 (1) ◽  
pp. 26-33
Author(s):  
Nurul Al Istigho Farola ◽  
Her Gumiwang ◽  
Sumber Sumber
Keyword(s):  
Measurement Data ◽  
Temperature Data ◽  
Average Error ◽  
Data Logger ◽  
Channel Temperature ◽  
Measurement Results ◽  
Temperature Data Logger ◽  
Sterilization Process ◽  
Thermocouple Temperature ◽  
Sd Card

Measuring the temperature on the dry sterilizer is very necessary because the temperature inside the dry sterilizer has the possibility that the temperature is not the same as the temperature that has been set and is displayed on the display. If the temperature in the dry sterilizer does not match the standard setting temperature for the sterilization process, then the sterilization process is said to be imperfect The purpose of this study is to record and monitor whether the distributed temperature in the sterilization chamber corresponds to the setting temperature. The workings of the temperature data logger tool is that the type K thermocouple temperature sensor will detect the temperature which then enters the analog signal conditioning circuit which then enters the ATMegga 2560 which has been given a program and processed in such a way, then the temperature will be displayed on a 4x20 character LCD. Temperature measurement data will be saved to the SD Card every 10 seconds in the form of a TXT file. This research has been used to record 2 sterilizers and compared with the Madgetech OctTemp2000 data logger. Based on data measurements and comparisons, the average error was obtained at a temperature of 50ºC with the smallest error value of 0.7% and the largest value of 3.9%. At a temperature of 100ºC, the smallest error value is 1.6% and the largest is 10.5%. Then at a temperature of 120ºC the smallest error value is 0.0% and the largest is 8.5%. This research can be used to help analyze the distribution of temperature in a room. With these measurement results, it can be said that this study still has afairly high error value at several measurement points.

scholarly journals Modeling of German Low Voltage Cables with Ground Return Path

Energies ◽  
2021 ◽  
Vol 14 (5) ◽  
pp. 1265 ◽  
Author(s):  
Johanna Geis-Schroer ◽  
Sebastian Hubschneider ◽  
Lukas Held ◽  
Frederik Gielnik ◽  
Michael Armbruster ◽  
...  
Keyword(s):  
Low Voltage ◽  
Measurement Data ◽  
Analytical Calculation ◽  
Laboratory Measurement ◽  
Model Parameters ◽  
Calculation Methods ◽  
Modeling Approach ◽  
Measurement Results ◽  
Simulation Results ◽  
Return Path

In this contribution, measurement data of phase, neutral, and ground currents from real low voltage (LV) feeders in Germany is presented and analyzed. The data obtained is used to review and evaluate common modeling approaches for LV systems. An alternative modeling approach for detailed cable and ground modeling, which allows for the consideration of typical German LV earthing conditions and asymmetrical cable design, is proposed. Further, analytical calculation methods for model parameters are described and compared to laboratory measurement results of real LV cables. The models are then evaluated in terms of parameter sensitivity and parameter relevance, focusing on the influence of conventionally performed simplifications, such as neglecting house junction cables, shunt admittances, or temperature dependencies. By comparing measurement data from a real LV feeder to simulation results, the proposed modeling approach is validated.

scholarly journals Inverse Infiltration Modeling of Dike Covers Made of Dredged Material Using PEST and AMALGAM

Geosciences ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 41
Author(s):  
Tim Jurisch ◽  
Stefan Cantré ◽  
Fokke Saathoff
Keyword(s):  
Large Scale ◽  
Measurement Data ◽  
Fine Grained ◽  
Dredged Materials ◽  
Measurement Results ◽  
Large Scale Field ◽  
Eigenvalue Ratio ◽  
Ill Posed ◽  
Materials Used ◽  
Installation Technology

A variety of studies recently proved the applicability of different dried, fine-grained dredged materials as replacement material for erosion-resistant sea dike covers. In Rostock, Germany, a large-scale field experiment was conducted, in which different dredged materials were tested with regard to installation technology, stability, turf development, infiltration, and erosion resistance. The infiltration experiments to study the development of a seepage line in the dike body showed unexpected measurement results. Due to the high complexity of the problem, standard geo-hydraulic models proved to be unable to analyze these results. Therefore, different methods of inverse infiltration modeling were applied, such as the parameter estimation tool (PEST) and the AMALGAM algorithm. In the paper, the two approaches are compared and discussed. A sensitivity analysis proved the presumption of a non-linear model behavior for the infiltration problem and the Eigenvalue ratio indicates that the dike infiltration is an ill-posed problem. Although this complicates the inverse modeling (e.g., termination in local minima), parameter sets close to an optimum were found with both the PEST and the AMALGAM algorithms. Together with the field measurement data, this information supports the rating of the effective material properties of the applied dredged materials used as dike cover material.

scholarly journals Design of Monitoring Tool Heartbeat Rate and Human Body Temperature Based on WEB

2018 ◽  
Vol 164 ◽  
pp. 01017 ◽  
Author(s):  
Jalinas ◽  
Wahyu Kusuma Raharja ◽  
Bobby Putra Emas Wijaya
Keyword(s):  
Heart Rate ◽  
Body Temperature ◽  
Human Body ◽  
Average Error ◽  
Web Pages ◽  
Test Results ◽  
Pulse Sensor ◽  
Measurement Results ◽  
Human Body Temperature ◽  
Error Percentage

The heart is one of the most important organs in the human body. One way to know heart health is to measure the number of heart beats per minute and body temperature also shows health, many heart rate and body temperature devices but can only be accessed offline. This research aims to design a heart rate detector and human body temperature that the measurement results can be accessed via web pages anywhere and anytime. This device can be used by many users by entering different ID numbers. The design consists of input blocks: pulse sensor, DS18B20 sensor and 3x4 keypad button. Process blocks: Arduino Mega 2560 Microcontroller, Ethernet Shield, router and USB modem. And output block: 16x2 LCD and mobile phone or PC to access web page. Based on the test results, this tool successfully measures the heart rate with an average error percentage of 2.702 % when compared with the oxymeter tool. On the measurement of body temperature get the result of the average error percentage of 2.18 %.

scholarly journals Measurement experiences with FluxSet digital D/I station

2017 ◽  
Vol 6 (2) ◽  
pp. 279-284 ◽  
Author(s):  
László Hegymegi ◽  
János Szöllősy ◽  
Csaba Hegymegi ◽  
Ádám Domján
Keyword(s):  
Measurement Method ◽  
Measurement Data ◽  
Digital Form ◽  
New Instrument ◽  
Measurement Results ◽  
Inclination Angles ◽  
Flux Gate

Abstract. Geomagnetic observatories use classical theodolites equipped with single-axis flux-gate magnetometers known as declination–inclination magnetometers (DIM) to determine absolute values of declination and inclination angles. This instrument and the measurement method are very reliable but need a lot of handwork and experience. The authors developed and built a non-magnetic theodolite which gives all measurement data in digital form. Use of this instrument significantly decreases the possibility of observation errors and minimises handwork. The new instrument is presented in this paper together with first measurement results in comparison to the classical DIM.

scholarly journals Prototype Sistem Deteksi Partial Discharge Pada Isolasi Kabel Menggunakan Sensor Microphone (Prototype Of Partial Discharge Detection System In Cable Isolation Using Microphone Sensor)

2019 ◽  
Vol 3 (2) ◽  
pp. 206
Author(s):  
Mochamad Zaeynuri Setiawan ◽  
Fachrudin Hunaini ◽  
Mohamad Mukhsim
Keyword(s):  
Detection System ◽  
Partial Discharge ◽  
Measurement Data ◽  
Negative Ions ◽  
High Sensitivity ◽  
Sound Waves ◽  
Cable Insulation ◽  
Insulation Failure ◽  
Measurement Results ◽  
Discharge Detection

The phenomenon that often arises in a substation is the problem of partial discharge in outgoing cable insulation. Partial discharge is a jump of positive and negative ions that are not supposed to meet so that it can cause a spark jump. If a partial discharge is left too long it can cause insulation failure, the sound of snakes like hissing and the most can cause a flashover on the outgoing cable. Then a partial discharge detection prototype was made in the cable insulation in order to anticipate the isolation interference in the outgoing cable. Can simplify the work of substation operators to check the reliability of insulation on the outgoing side of each cubicle. So it was compiled as a method for measuring sound waves caused by partial discharge in the process of measuring using a microphone sensor, the Arduino Mega 2560 module as a microcontroller, the LCD TFT as a monitoring and the MicroSD card module as its storage. The microphone sensor is a sensor that has a high sensitivity to sound, has 2 analog and digital readings, and is easily designed with a microcontroller. Basically the unit of measure measured at partial discharge is Decibels. The results of the prototype can be applied to the cubicle and the way it works is to match the prototype to the outgoing cubicle cable then measure from the cable boots connector to the bottom of the outgoing cable with a distance of 1 meter. Then the measurement results will be monitored on the TFT LCD screen in the form of measurement results, graphs and categories on partial discharge. In this design the measurement data made by the microphone can be stored with microSD so that it can make an evaluation of partial discharge handling in outgoing cable insulation.

scholarly journals Apnea Monitor based on Bluetooth with Android Interface

2020 ◽  
Vol 1 (2) ◽  
pp. 50-56
Author(s):  
I Dewa Made Wirayuda ◽  
I Dewa Gede Hari Wisana ◽  
Priyambada Cahya Nugraha
Keyword(s):  
Risk Factors ◽  
Cardiovascular Disease ◽  
Obstructive Sleep Apnea ◽  
Sleep Apnea ◽  
Sudden Death ◽  
Respiration Rate ◽  
Average Error ◽  
Obstructive Sleep ◽  
Testing And Measurement ◽  
Mit App Inventor

Apnea monitor is a device that is used to give a warning if there is stop breathing. Stop breathing while sleeping is one form of obstructive sleep apnea. This cessation of breath cannot be underestimated, this is related to the main risk factors for health implications and increased cardiovascular disease and sudden death. The purpose of this study is to design an apnea monitor with the Android interface. This device allows the users to get how many times sleep apnea happens while sleeping and got data to analysis before continuing with a more expensive and advanced sleep test. This device used a flex sensor to detect the respiration rate, the sensor placed on the abdomen or belly so it can measure expand and deflate while breathing. The microcontroller uses an Arduino chip called AT-Mega328. Bluetooth HC-05 used to send respiration data to Android, MIT app inventor used for the android programmer, and on the android, there are plotting of respiration value and when the device detected apnea so the android also gives a warning to the user. Based on the results of testing and measurement then compare with another device, the results of the average% error were 3.61%. This apnea monitor design is portable but there are needs some improvement by using another sensor for detected respiration and using a module other than Bluetooth.

scholarly journals Making roundness measurement applications and control systems on the Roundness Tester Machine

2019 ◽  
Vol 63 (3) ◽  
pp. 17-21
Author(s):  
Dodi Sofyan Arief ◽  
◽  
Eko Jadmiko ◽  
Adhy Prayitno ◽  
Muftil Badri ◽  
...  
Keyword(s):  
Control Systems ◽  
Measurement Data ◽  
Rotating Speed ◽  
Center Point ◽  
Global Quality ◽  
Measurement Results ◽  
Roundness Deviation ◽  
And Control ◽  
Dial Indicator ◽  
Roundness Measurement

Dial indicator is a comparison device usually used in industrial activities, especially in production. To make measurements at this time must be supported by technology that can facilitate operators when using it and when analyzing measurement results. Involving the programme and microcontroller are a solution to developing in roundness measurement, and then the results can be more accurate or thorough between the readable values read from the measuring instrument with the actual value of varying the amount of data. Roundness application is a program that can input measurement data automatically and can do calculations directly. Then, it can display a reference circle, a table that calculates the values of X, Y, R, X’, Y’, R’, Roundness Deviation, Run out Concentricity or a shift in the center point and also the center point shift or Theta. In measuring roundness, the test object is used the Standard Mandrel which has been certified by PT. Global Quality Indonesia, by determining three points or positions, namely in the first position the amount of data is 180, in the second position the amount of data is 90 and in the third position, the amount of data is 60 with a rotating speed of 15 mm/s. The results of the reference circle can be seen in each calculation in each position, in the second position the roundness deviation values are approaching of the Mandrel.

Sign in / Sign up

Export Citation Format

Share Document