scholarly journals Experimental of Mechanical Properties in Glass Fiber by using Epoxy and Polyester Resin

2020 ◽  
Vol 8 (4S5) ◽  
pp. 299-301
Keyword(s):  
Mechanical Properties ◽  
Glass Fiber ◽  
Zirconium Dioxide ◽  
Impact Test ◽  
Polyester Resin ◽  
Glass Fibers ◽  
Physical And Mechanical Properties ◽  
Hardness Test ◽  
Water Absorption Test ◽  
Test Impact

Alkali Resistant Glass Fibers are designed specifically for use in concrete. It is made from a specially developed glass composition of zirconium dioxide which is appropriately used in concrete. It is to evaluate and compare the physical and mechanical properties of laminates prepared of different composition of Glass fiber. In this experiment, two specimens with different composition was taken and prepared by using hand layup method. Tensile test, Impact test and Brinell hardness test were carried out and their performances were evaluated. In this experiment, composite was subjected to water absorption test. From the result, property of two specimen was compared and analyzed.

Fabrication and Characterization of E-Glass Fiber Reinforced Unsaturated Polyester Resin Based Composite Materials

2019 ◽  
Vol 24 ◽  
pp. 1-7
Author(s):  
Md. Naimul Islam ◽  
Harun Ar-Rashid ◽  
Farhana Islam ◽  
Nanda Karmaker ◽  
Farjana A. Koly ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Glass Fiber ◽  
Bending Strength ◽  
Polyester Resin ◽  
Unsaturated Polyester ◽  
Glass Fibers ◽  
Tensile Modulus ◽  
Unsaturated Polyester Resin ◽  
Fiber Reinforced ◽  
Bending Modulus

E-glass fiber mat reinforced Unsaturated Polyester Resin (UPR)-based composites were fabricated by conventional hand lay-up technique. The fiber content was varied from 5 to 50% by weight. Mechanical properties (tensile and bending) of the fabricated composites were investigated. The tensile strength (TS) of the 5% and 50% fiber reinforced composites was 32 MPa and 72 MPa, respectively. Similarly, tensile modulus, bending strength and bending modulus of the composites were increased by the increase of fiber loading. Interfacial properties of the composites were investigated by scanning electron microscopy (SEM) and the results revealed that the interfacial bond between fiber and matrix was excellent. Keywords: Unsaturated Polyester Resin, Mechanical Properties, E-glass Fibers, Composites, Polymer.

scholarly journals Mechanical properties of composite material laminates reinforced by woven and non-woven glass fibers

2020 ◽  
Vol 175 ◽  
pp. 12005 ◽  
Author(s):  
Amer Karnoub ◽  
Hajian Huang ◽  
Imad Antypas
Keyword(s):  
Mechanical Properties ◽  
Composite Material ◽  
Glass Fiber ◽  
Mechanical Characteristics ◽  
Polyester Resin ◽  
Mechanical Performance ◽  
Glass Fibers ◽  
Mechanical Tests ◽  
Impact Behavior ◽  
The Impact

The purpose of this work is to study the mechanical characteristics in 3-point bending and in traction; static; and the impact behavior of three specimens of laminates made of glass fiber and polyester resin non-woven and woven, with the aim of using them in the repair of boat hulls and enhancing their value in the naval industry. Three types of laminates were developed by contact molding. These different specimens of laminates made of woven, non-woven and combined glass fiber (woven and non-woven) were subjected to mechanical tests (traction and 3-point bending). Analysis of the results of the tests carried out on these three types of laminate shows that one specimen stands out and gives higher mechanical performance than the othertwo.

scholarly journals Mechanical Properties of Longitudinal Basalt/Woven-Glass-Fiber-reinforced Unsaturated Polyester-Resin Hybrid Composites

Polymers ◽  
2020 ◽  
Vol 12 (10) ◽  
pp. 2211
Author(s):  
S.M. Sapuan ◽  
H.S. Aulia ◽  
R.A. Ilyas ◽  
A. Atiqah ◽  
T.T. Dele-Afolabi ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Glass Fiber ◽  
Polyester Resin ◽  
Hybrid Composites ◽  
Unsaturated Polyester ◽  
Glass Fibers ◽  
Unsaturated Polyester Resin ◽  
Fiber Reinforced ◽  
Glass Fiber Reinforced ◽  
Woven Glass Fiber

This work represents a study to investigate the mechanical properties of longitudinal basalt/woven-glass-fiber-reinforced unsaturated polyester-resin hybrid composites. The hybridization of basalt and glass fiber enhanced the mechanical properties of hybrid composites. The unsaturated polyester resin (UP), basalt (B) and glass fibers (GF) were fabricated using the hand lay-up method in six formulations (UP, GF, B7.5/G22.5, B15/G15, B22.5/G7.5 and B) to produce the composites, respectively. This study showed that the addition of basalt to glass-fiber-reinforced unsaturated polyester resin increased its density, tensile and flexural properties. The tensile strength of the B22.5/G7.5 hybrid composites increased by 213.92 MPa compared to neat UP, which was 8.14 MPa. Scanning electron microscopy analysis was used to observe the fracture mode and fiber pullout of the hybrid composites.

scholarly journals Mechanical behavior of transparent fiber reinforced polyester composites at extreme temperatures

2018 ◽  
Author(s):  
◽  
Saad Ramadhan Ahmed
Keyword(s):  
Mechanical Properties ◽  
Glass Fiber ◽  
Polyester Resin ◽  
Unsaturated Polyester ◽  
Glass Fibers ◽  
Fiber Reinforced Polymers ◽  
Extreme Conditions ◽  
Fiber Reinforced ◽  
Glass Fiber Reinforced ◽  
The Impact

Selecting materials for harsh or extreme environmental conditions can be a challenge. The combination of a harsh environment, large forces over extended periods and the need for lowest possible cost restricts the choice of materials. One potential material is glass fiber reinforced polymers that are widely used in structural systems as load bearing elements, they are relatively low cost and can be tailored to achieve a range of mechanical properties. This investigation presents the preparation of transparent glass fiber reinforced unsaturated polyester composite and the evaluation of its optical and mechanical properties under extreme conditions of temperature. The polyester resin was reinforced with E-glass fibers to manufacture a composite using the hand layup method. Transparency was achieved by modifying the refractive index of the polyester resin to match that of the glass fibers. This investigation also presents the evaluation of glass fiber reinforced unsaturated polyester under quasi-static tension loading and puncture testing using a drop weight at extreme conditions. The results showed that the reinforced composite had a higher fracture stress and chord modulus at all temperatures ranging from +60 [degree]C to -80 [degree]C as compared to the unreinforced polyester matrix. The unreinforced polyester has a higher stiffness at lower temperatures due to reduced polymer chain mobility and higher clamping pressure of the matrix on the glass fiber reinforcement. The damage created by the impact reduces with decreasing temperatures, while the energy absorb remains constant with temperature.

Physical and mechanical properties of unsaturated polyester resin matrix from recycled PET (based PG ) with corn straw fiber

2021 ◽  
pp. 51305
Author(s):  
Nora Abigail Wilson García ◽  
Jorge Luis Almaral Sánchez ◽  
Ramón Álvaro Vargas Ortiz ◽  
Abel Hurtado Macías ◽  
Nelly Flores Ramírez ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Polyester Resin ◽  
Unsaturated Polyester ◽  
Physical And Mechanical Properties ◽  
Unsaturated Polyester Resin ◽  
Resin Matrix ◽  
Corn Straw ◽  
Recycled Pet

scholarly journals Effects of Different Types of Fibers on the Physical and Mechanical Properties of MICP-Treated Calcareous Sand

Materials ◽  
2021 ◽  
Vol 14 (2) ◽  
pp. 268
Author(s):  
Jitong Zhao ◽  
Huawei Tong ◽  
Yi Shan ◽  
Jie Yuan ◽  
Qiuwang Peng ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Water Absorption ◽  
Glass Fiber ◽  
Physical And Mechanical Properties ◽  
Polyester Fiber ◽  
Engineering Properties ◽  
Fiber Types ◽  
Calcite Precipitation ◽  
Calcareous Sand ◽  
Hemp Fiber

Microbial-induced calcite precipitation (MICP) has been a promising method to improve geotechnical engineering properties through the precipitation of calcium carbonate (CaCO3) on the contact and surface of soil particles in recent years. In the present experiment, water absorption and unconfined compressive strength (UCS) tests were carried out to investigate the effects of three different fiber types (glass fiber, polyester fiber, and hemp fiber) on the physical and mechanical properties of MICP-treated calcareous sand. The fibers used were at 0%, 0.10%, 0.15%, 0.20%, 0.25%, 0.30%, 0.35%, and 0.40% relative to the weight of the sand. The results showed that the failure strain and ductility of the samples could be improved by adding fibers. Compared to biocemented sand (BS), the water absorption of these three fiber-reinforced biocemented sands were, respectively, decreased by 11.60%, 21.18%, and 7.29%. UCS was, respectively, increased by 24.20%, 60.76%, and 6.40%. Polyester fiber produced the best effect, followed by glass fiber and hemp fiber. The optimum contents of glass fiber and polyester fiber were 0.20% and 0.25%, respectively. The optimum content of hemp fiber was within the range of 0.20–0.25%. Light-emitting diode (LED) microscope and scanning electron microscope (SEM) images lead to the conclusion that only a little calcite precipitation had occurred around the hemp fiber, leading to a poor bonding effect compared to the glass and polyester fibers. It was therefore suggested that polyester fiber should be used to improve the properties of biocemented sand.

Experimental investigation of the mechanical behavior of glass fiber/high fluidity polyamide-based composites for automotive market

2021 ◽  
pp. 073168442110140
Author(s):  
Hossein Ramezani-Dana ◽  
Moussa Gomina ◽  
Joël Bréard ◽  
Gilles Orange
Keyword(s):  
Mechanical Properties ◽  
Glass Fiber ◽  
Mechanical Performance ◽  
Physical And Mechanical Properties ◽  
Ultimate Strain ◽  
Uniaxial Tensile ◽  
Compression Tests ◽  
Automotive Market ◽  
Glass Fiber Reinforced ◽  
Glass Fiber Reinforcement

In this work, we examine the relationships between the microstructure and the mechanical properties of glass fiber–reinforced polyamide 6,6 composite materials ( V f = 54%). These materials made by thermocompression incorporate different grades of high fluidity polyamide-based polymers and two types of quasi-UD glass fiber reinforcement. One is a classic commercial fabric, while the other specially designed and manufactured incorporates weaker tex glass yarns (the spacer) to increase the planar permeability of the preform. The effects of the viscosity of the polymers and their composition on the wettability of the reinforcements were analyzed by scanning electron microscopy observations of the microstructure. The respective influences of the polymers and the spacer on the mechanical performance were determined by uniaxial tensile and compression tests in the directions parallel and transverse to the warp yarns. Not only does the spacer enhance permeability but it also improves physical and mechanical properties: tensile longitudinal Young’s modulus increased from 38.2 GPa to 42.9 GPa (13% growth), tensile strength increased from 618.9 MPa to 697 MPa (3% growth), and decrease in ultimate strain from 1.8% to 1.7% (5% reduction). The correlation of these results with the damage observed post mortem confirms those acquired from analyses of the microstructure of composites and the rheological behaviors of polymers.

scholarly journals The Mechanical Properties and Damage Evolution of UHPC Reinforced with Glass Fibers and High-Performance Polypropylene Fibers

Materials ◽  
2021 ◽  
Vol 14 (9) ◽  
pp. 2455
Author(s):  
Jiayuan He ◽  
Weizhen Chen ◽  
Boshan Zhang ◽  
Jiangjiang Yu ◽  
Hang Liu
Keyword(s):  
Mechanical Properties ◽  
Glass Fiber ◽  
Damage Evolution ◽  
High Performance ◽  
High Performance Concrete ◽  
Glass Fibers ◽  
Ultra High Performance Concrete ◽  
Concrete Damaged Plasticity ◽  
The Difference ◽  
Experimental Values

Due to the sharp and corrosion-prone features of steel fibers, there is a demand for ultra-high-performance concrete (UHPC) reinforced with nonmetallic fibers. In this paper, glass fiber (GF) and the high-performance polypropylene (HPP) fiber were selected to prepare UHPC, and the effects of different fibers on the compressive, tensile and bending properties of UHPC were investigated, experimentally and numerically. Then, the damage evolution of UHPC was further studied numerically, adopting the concrete damaged plasticity (CDP) model. The difference between the simulation values and experimental values was within 5.0%, verifying the reliability of the numerical model. The results indicate that 2.0% fiber content in UHPC provides better mechanical properties. In addition, the glass fiber was more significant in strengthening the effect. Compared with HPP-UHPC, the compressive, tensile and flexural strength of GF-UHPC increased by about 20%, 30% and 40%, respectively. However, the flexural toughness indexes I5, I10 and I20 of HPP-UHPC were about 1.2, 2.0 and 3.8 times those of GF-UHPC, respectively, showing that the toughening effect of the HPP fiber is better.

Optically Transparent Polymethyl Methacrylate Composites made with Glass Fibers of Varying Refractive Index

1997 ◽  
Vol 12 (4) ◽  
pp. 1091-1101 ◽  
Author(s):  
Seunggu Kang ◽  
Hongy Lin ◽  
Delbert E. Day ◽  
James O. Stoffer
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Refractive Index ◽  
Mechanical Strength ◽  
Glass Fiber ◽  
Polymethyl Methacrylate ◽  
Optical Transmission ◽  
Annealing Temperature ◽  
Glass Fibers ◽  
Optically Transparent

The dependence of the optical and mechanical properties of optically transparent polymethyl methacrylate (PMMA) composites on the annealing temperature of BK10 glass fibers was investigated. Annealing was used to modify the refractive index (R.I.) of the glass fiber so that it would more closely match that of PMMA. Annealing increased the refractive index of the fibers and narrowed the distribution of refractive index of the fibers, but lowered their mechanical strength so the mechanical properties of composites reinforced with annealed fibers were not as good as for composites containing as-pulled (chilled) glass fibers. The refractive index of as-pulled 17.1 μm diameter fibers (R.I. = 1.4907) increased to 1.4918 and 1.4948 after annealing at 350 °C to 500 °C for 1 h or 0.5 h, respectively. The refractive index of glass fibers annealed at 400 °C/1 h best matched that of PMMA at 589.3 nm and 25 °C, so the composite reinforced with those fibers had the highest optical transmission. Because annealed glass fibers had a more uniform refractive index than unannealed fibers, the composites made with annealed fibers had a higher optical transmission. The mechanical strength of annealed fiber/PMMA composites decreased as the fiber annealing temperature increased. A composite containing fibers annealed at 450 °C/1 h had a tensile strength 26% lower than that of a composite made with as-pulled fibers, but 73% higher than that for unreinforced PMMA. This decrease was avoided by treating annealed fibers with HF. Composites made with annealed and HF (10 vol. %)-treated (for 30 s) glass fibers had a tensile strength (∼200 MPa) equivalent to that of the composites made with as-pulled fibers. However, as the treatment time in HF increased, the tensile strength of the composites decreased because of a significant reduction in diameter of the glass fiber which reduced the volume percent fiber in the composite.

scholarly journals INVESTIGATION INTO PHYSICAL AND MECHANICAL PROPERTIES OF POLYMERIC SAND USED FOR COWSHED FLOORING

2019 ◽  
Vol 54 (4) ◽  
pp. 116-123
Author(s):  
P.V. Dorodov ◽  
◽  
M.R. Kudrin ◽  
A.V. Kostin ◽  
V.A. Nikolaev ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Cast Iron ◽  
Mechanical Characteristics ◽  
Dynamic Stress ◽  
Impact Test ◽  
Gray Cast Iron ◽  
Physical And Mechanical Properties ◽  
Floor Covering ◽  
Carbon Structural Steel ◽  
Impact Viscosity

Physical and mechanical properties of the polymeric sand used as floor covering in cattle stalls were investigated. Samples of the polymeric sand were tested under static and dynamic stress, an impact test was done, mechanical characteristics were measured, and the material structural efficiency was evaluated. The polymeric sand tile appeared strong, reliable and durable material. The study material exhibited viscoelasticity. The polymeric sand samples demonstrated impact viscosity in the range 242,3– 548,3 kJ/m2 . The figure was 3,5–13,7 times higher than that of gray cast iron and was comparable with some classes of carbon structural steel. Mechanical properties of the polymeric sand were analysed. The characteristics revealed in the analysis can be used in dimensioning and designing products made from polymeric sand under various strength indices.

Sign in / Sign up

Export Citation Format

Share Document