scholarly journals TINJAUAN HUBUNGAN KUAT TEKAN DAN LENTUR BETON DENGAN BAHAN TAMBAH SERAT BAJA UNTUK PERKERASAN PAKU

2019 ◽  
Vol 3 (1) ◽  
pp. 1-5
Author(s):  
Hermansyah Hermansyah ◽  
Muhammad Fauzie Siswanto ◽  
Ashar Saputra
Keyword(s):  
Compressive Strength ◽  
Flexural Strength ◽  
Steel Fiber ◽  
Concrete Mixture ◽  
Director General ◽  
Normal Concrete ◽  
Rigid Pavement ◽  
Concrete Quality ◽  
Relationship Of ◽  
The Relationship

The Director General of Highways issued the 2010 revision 3 specification concerning minimum flexural strength for rigid pavement of 45 kg/cm2 or approximately 4.5 MPa, but the reality of obtaining such flexural strength should be using  high enough concrete quality and it will incur considerably high cost also. In this study was using a normal concrete method with the purpose of research to know  the relationship of compressive strength and flexural of concrete with the addition of variation of fiber 0%, 0,5%, 0,65% and 0,8% from weight of the concrete mixture. The results from this research showed that the compressive strength and flexure had increased successively in the fiber variation 0%, 0.5% and 0.65% amount 31.23 MPa, 33.06 MPa, 35.23 MPa and 4.58 MPa, 4.75 MPa, 5.04 MPa. It is because the fiber contained in the concrete has a fairly even distribution of fiber and does not have clumping. When variations of fiber above 0.65% such as 0.8% variation in the direction of fiber are difficult to control and at the time of mixing occurs clumping, So the value of compressive strength and flexural of concrete are decreases. The relation of compressive strength and flexural of concrete using a variation of steel fiber to obtain equation fs = 0,1226.fc '+ 0,7173 with value R2 = 0,9915 and α 0,82. The results obtained from the test is a rather good when compared with ACI and SNI T- 15-1991-03 method.

scholarly journals PERBANDINGAN KEKUATAN BETON DENGAN CAMPURAN DRAMIX STEEL FIBER DAN TULANGAN WIREMESH PADA RIGID PAVEMENT (Comparison of the Strength of Concrete with a mixture of Dramix Steel Fiber and Wiremesh Reinforcement on Rigid Pavement)

2018 ◽  
Vol 1 (2) ◽  
Author(s):  
Two Puji Guntur A ◽  
Yosef Cahyo ◽  
Sigit Winarto
Keyword(s):  
Compressive Strength ◽  
Flexural Strength ◽  
Bending Strength ◽  
Steel Fiber ◽  
Strength Test ◽  
Concrete Mixture ◽  
Rigid Pavement ◽  
Beam Sample ◽  
Compressive Loads ◽  
Average Compressive Strength

ABSTRACTConcrete has a weakness that is having a low tensile strength and brittle so that the concrete is given steel reinforcement to anticipate it. In this study, the concrete mixture was added with dramix steel fiber. This addition was carried out to study and determine the effect of dramix steel fiber on compressive strength, flexural strength on normal quality concrete with the addition of 0%, 10%, 20% and 30% in compressive loads. Compressive strength specimens in the form of cylinders with a diameter of 15 cm and a height of 30 cm and bending strength test specimens in the form of blocks with a length of 60 cm, width of 15 cm and height of 15 cm. Testing is done after 28 days. Concrete with the addition of dramix steel fiber is 30% more capable of producing a higher compressive strength than the others. The addition of dramix steel fiber resulted in an average compressive strength of 0%, 29.07 MPa, 10%, 29.33 MPa, 20%, 29.40 MPa, 30%, 29.58 MPa. For the highest flexural strength of concrete in the 15/15/60 beam sample, that is in the concrete mixture and the addition of dramix steel fiber of 5.44 MPa, it is higher than the addition of reinforcement iron m8, which is 4.96 MPa.Keywords:Dramix Steel Fiber, compressive strength, concrete flexural strength, m8 wiremesh

scholarly journals PENELITIAN UJI KUAT TEKAN BETON DENGAN MEMANFAATKAN AIR LIMBAH TETES TEBU DAN ZAT ADDITIVE CONCRETE

2019 ◽  
Vol 2 (1) ◽  
pp. 16
Author(s):  
Mochamad Ahsin Ansori ◽  
Ahmad Ridwan ◽  
Yosef Cahyo
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Flexural Strength ◽  
Sugar Cane ◽  
Steel Reinforcement ◽  
Concrete Mixture ◽  
Normal Concrete ◽  
Beam Sample ◽  
Compressive Loads

Concrete has a weakness that is having a low tensile strength and brittle so that the concrete is given steel reinforcement to anticipate it. This addition was carried out to study and determine the effect of sugarcane waste on compressive strength, flexural strength on normal quality concrete with the addition of 0%, 10%, 20% and 30% in compressive loads. Testing is done after 28 days. Concrete with the addition of 30% sugar cane is more capable of producing high flexural strength than the others. Addition of sugar cane drops resulted in optimum compressive strength of 10%, 16.75MPa, 20%, 16.55MPa, 30%, 16.40MPa. For the highest flexural strength of concrete in the 15/15/60 beam sample, the concrete mixture was added to 30% sugar cane by 5.00 MPa, higher than normal concrete 4.96 MPa.Beton mempunyai kelemahan yaitu mempunyai kuat tarik yang rendah dan bersifat getas (brittle) sehingga beton diberi tulangan baja untuk mengantisipasinya. Penambahan ini dilakukan untuk mempelajari dan mengetahui pengaruh limbah tetes tebu terhadap kuat tekan, kuat lentur pada beton mutu normal dengan penambahan 0%, 10%, 20% dan 30% pada beban tekan. Pengujian dilakukan setelah 28 hari. Beton dengan penambahan tetes tebu 30% lebih mampu menghasilkan nilai kuat lentur tinggi dari pada yang lainya. Penambahan limbah tetes tebu menghasilakan kuat tekan optimum yaitu,10%,16,75MPa, 20%,16,55MPa, 30%,16,40MPa. Untuk kuat lentur beton pada sampel balok 15/15/60 yang paling tinggi yaitu pada campuran beton penambahan tetes tebu 30% sebesar 5,00 MPa, lebih tinggi dari pada beton normal 4,96 MPa. 

An evaluation of ECT sample height for small flute board grades and Box Manufacturer’s Certification compliance

TAPPI Journal ◽  
2009 ◽  
Vol 8 (6) ◽  
pp. 24-28
Author(s):  
CORY JAY WILSON ◽  
BENJAMIN FRANK
Keyword(s):  
Compressive Strength ◽  
Compressive Load ◽  
Test Sample ◽  
Test Methods ◽  
Test Method ◽  
Initial Development ◽  
Sample Height ◽  
Relationship Of ◽  
The Relationship ◽  
Corrugated Fiberboard

TAPPI test T811 is the specified method to ascertain ECT relative to box manufacturer’s certification compliance of corrugated fiberboard under Rule 41/ Alternate Item 222. T811 test sample heights were derived from typical board constructions at the time of the test method’s initial development. New, smaller flute sizes have since been developed, and the use of lighter weight boards has become more common. The T811 test method includes sample specifications for typical A-flute, B-flute, and C-flute singlewall (and doublewall and triplewall) structures, but not for newer thinner E-flute or F-flute structures. This research explores the relationship of ECT sample height to measured compressive load, in an effort to determine valid E-flute and F-flute ECT sample heights for use with the T811 method. Through this process, it identifies challenges present in our use of current ECT test methods as a measure of intrinsic compressive strength for smaller flute structures. The data does not support the use of TAPPI T 811 for ECT measurement for E and F flute structures, and demonstrates inconsistencies with current height specifi-cations for some lightweight B flute.

scholarly journals Pengaruh Pemanfaatan Abu Tumbuhan Perumpung Terhadap Peningkatan Kuat Tekan Beton K300

Jurnal Tekno ◽  
2021 ◽  
Vol 18 (2) ◽  
pp. 11-20
Author(s):  
Ahmad Junaidi ◽  
R Dewo Hiraliyamaesa Hariyanto
Keyword(s):  
Compressive Strength ◽  
Test Object ◽  
Concrete Mixture ◽  
Wild Plant ◽  
Concrete Compressive Strength ◽  
Normal Concrete ◽  
Compressive Strength Of Concrete ◽  
Test Objects

Perumpung (Eulalia japonica) is a wild plant that usually grows on the banks of river. The locals consider this plant as a waste/pest, but the authors are interested in researching perumpung because they are similar to bamboo, sugarcane and other fibrous plants. In this study, the authors aims to compare the compressive strength of normal concrete with the compressive strength of concrete added with Perumpung ash at 28-days-old K-300. The study used a cube-shaped test object (15 x 15 x 15 cm) with 6 samples for each condition. The total number of test objects is 48, which consists of 8 conditions, namely normal conditions and 5%, 7.5%, 10%, 12.5%, 15%, 17.5% and 20% addition of perumpung ash by cement weight. The results obtained that the compressive strength of 28-days-old concrete under normal conditions was 316,060 kg/cm2 and the addition of 5% ash was 331.583 kg/cm2, 7.5% was 337.181 kg/cm2, 10% was 341.813 kg/cm2, 12 ,5% is 347,045 kg/cm2, 15% is 353,889 kg/cm2, 17.5% is 311,160 kg/cm2 and 20% is 298.44 kg/cm2. From the results above it can be concluded that the addition of 15% Perumpung Ash to the concrete mixture increases the maximum characteristic concrete compressive strength by 353.889 kg/cm2.

scholarly journals PENGARUH PENAMBAHAN SERAT ECENG GONDOK PADA KUAT TEKAN PAVING BLOCK K-200

UKaRsT ◽  
2019 ◽  
Vol 3 (1) ◽  
pp. 21
Author(s):  
Muttaqin Fauzin Istighfarin ◽  
Rasio Hepiyanto
Keyword(s):  
Compressive Strength ◽  
Water Hyacinth ◽  
Building Materials ◽  
Rigid Pavement ◽  
Cast Concrete ◽  
Additional Water ◽  
Materials Used ◽  
Relationship Of ◽  
Water Hyacinth Fiber

Abstract Paving block is one of the products of building materials used as the top layer of the street structure, compared to other pavements like cast concrete and asphalt, paving block has been widely chosen especially to the streets used to traversed by low-speeed vehicles. This study aims to know and analyze how strong the influence of additional water hyacinth fiber to the compressive strength of K-200 paving block. Method used in this study is experimental method, with the comparison of mix design reffering to the comparison of concrete quality mixture K-200 (SNI 7394-2008). The result is K-200 paving block decreases its compressive strength after given the mixture of water hyacinth fiber. The precentage of the lowest decrease is in the 0,2 mixture of 55,69% and the highest decrease is in the mixture of 0,8 with the decline presentage of of 82,39%. The score of compressive strength for each test object is: Normal of 209,53 kg/cm², 2% of 92,86 kg/cm², 4% of 84,53 kg/cm², 6% of 58,33 kg/cm², and 8% of 36,90 kg/cm². The relationship of non-linear regression can be seen in R² = 1 on  polinomial orde 4. Paving block with with code objects test “Normal” classified as in the quality of paving block B with compressive strength of 209,53 kg/cm² (17,03 Mpa), while for paving block with extra water hyacinth fiber, it is below the compressive strength standard according to SNI 03-0691-1996. Keywords: Rigid Pavement, Paving Block, Water Hyacinth, Compressive Strength.

Influence the Carbonation Resistance and Mechanical Properties of Shotcrete by Accelerated Carbonation Test

2014 ◽  
Vol 1065-1069 ◽  
pp. 1985-1989
Author(s):  
Jia Bin Wang ◽  
Di Tao Niu ◽  
Rui Ma ◽  
Ze Long Mi
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Steel Fiber ◽  
Splitting Tensile Strength ◽  
Construction Technology ◽  
Accelerated Carbonation ◽  
Carbonation Depth ◽  
Normal Concrete ◽  
Carbonation Resistance

In order to investigate the carbonation resistance of shotcrete and the mechanical properties after carbonation, the accelerated carbonation test was carried out. The results indicate that the carbonation resistance of shotcrete is superior to that of normal concrete. With the increasing of carbonation depth, compressive strength and splitting tensile strength of shotcrete grew rapidly. The admixing of steel fiber can further improve the carbonation resistance, reduce the carbonation rate, and increase the splitting tensile strength of shotcrete greatly. Besides, based on analyzing the effects of construction technology and steel fiber of concrete for the carbonation resistance, a carbonation depth model for shotcrete was established. Key words: shotcrete; carbonation; steel fiber; mechanical properties

Strength and Toughness of Steel Fiber Reinforced Heavy Concrete

2012 ◽  
Vol 512-515 ◽  
pp. 2908-2913 ◽  
Author(s):  
Yu Cheng Kan ◽  
Hsuan Chih Yang ◽  
Kuang Chih Pei
Keyword(s):  
Experimental Study ◽  
Compressive Strength ◽  
Power Plant ◽  
Nuclear Power Plant ◽  
Nuclear Power ◽  
Iron Ore ◽  
Steel Fiber ◽  
Test Results ◽  
Spent Fuel ◽  
Normal Concrete

This paper presents an experimental study dealing with the toughness of heavy concrete based on the ASTM C1018. Mixtures including 0%, 0.5%, 1.0% and 1.5% of steel fiber content by volume are designated, which are developed based on a mixture used in Kuosheng nuclear power plant in Taiwan. Metallic aggregates of iron shots and iron ore take 48.8% by volume in that mixture. Test results reveal that the compressive strength and rupture modulus of heavy concrete turn out higher than those of normal concrete. In addition, flexural toughness of heavy concrete grow with the steel fiber fraction, which is valid and appropriate for construction of shielding structure and spent fuel cask.

Research on the Main Mechanical Capability of Steel Fibers Concrete of Deck Pavement

2011 ◽  
Vol 374-377 ◽  
pp. 1619-1622
Author(s):  
Ling Zhang ◽  
Zhi Qiang Shi
Keyword(s):  
Compressive Strength ◽  
Shear Strength ◽  
Service Life ◽  
Flexural Strength ◽  
Steel Fiber ◽  
Mechanical Performance ◽  
Volume Ratio ◽  
Steel Fibers ◽  
Fiber Types ◽  
Splitting Strength

In this article, based on a certain actual project, the main physical and mechanical performance including compressive strength, splitting strength, flexural strength and shear strength are studied in detail through the experiments. Different fiber types and volume ratio are chosen in the experiments for the purpose of determining the best quantities and types of steel fiber in concrete to lengthen the service life of deck pavements. It is showed that the research has some referential value for similar projects.

Orthogonal Experimental Study on Properties of Hybrid Fiber Reinforced Cement Mortar

2010 ◽  
Vol 168-170 ◽  
pp. 456-459
Author(s):  
Hai Yan Yuan ◽  
Shui Zhang ◽  
Guo Zhong Li
Keyword(s):  
Compressive Strength ◽  
Flexural Strength ◽  
Steel Fiber ◽  
Cement Mortar ◽  
Polypropylene Fiber ◽  
Fiber Reinforced ◽  
Hybrid Fiber ◽  
Factors Affecting ◽  
Fiber Fraction ◽  
Reinforced Cement

By adopting the method of orthogonal experimental design, the effect of three independent variables, that is steel fiber fraction, polypropylene fiber fraction and silica fume fraction on the compressive strength, flexural strength and shrinkage of cement mortar was studied. The results indicate that steel fiber is one of the most important factors affecting compressive strength and shrinkage, and polypropylene fiber is one of the most important factors affecting flexural strength and shrinkage of cement mortar. By using deviation analysis to analyze the orthogonal experiment results, the optimized mix proportion of hybrid fiber reinforced cement mortar is determined. The hybrid effect of steel fiber and polypropylene fiber on the properties of cement mortar is discussed.

Research on Impact Behavior of Reactive Powder Concrete

2010 ◽  
Vol 150-151 ◽  
pp. 779-782
Author(s):  
Qing Xin Zhao ◽  
Zhao Yang Liu ◽  
Jin Rui Zhang ◽  
Ran Ran Zhao
Keyword(s):  
Compressive Strength ◽  
Impact Toughness ◽  
Flexural Strength ◽  
Steel Fiber ◽  
Volume Fraction ◽  
Impact Behavior ◽  
Reactive Powder Concrete ◽  
Flexural Toughness ◽  
Reactive Powder ◽  
The Impact

By means of the three-point bending impact equipment, with the measurement of ultrasonic velocity, the impact behavior and damage evolution of reactive powder concrete (RPC) with 0, 1%, 2% and 3% volume fraction of steel fiber were tested. The results showed that steel fiber significantly improved the compressive strength, flexural strength, flexural toughness and impact toughness of RPC matrix. The compressive strength, flexural strength, flexural toughness of RPC with 3% steel fiber increased by 40.1%, 102.1%, and 37.4 times than that of plain concrete, respectively, and simultaneously, the impact toughness of RPC with 3% steel fiber was 93.2 times higher than that with 1% steel fiber. RPC with 2% and 3% steel fiber dosage both had relatively high compressive strength, flexural strength and flexural toughness; however, compared with the sample with 2% steel fiber dosage, the impact toughness of RPC with 3% steel fiber dosage increased by more than 10 times. Therefore, taking economy and applicability into consideration, if we mainly emphasis on the compressive strength, flexural strength and flexural toughness, RPC with 2% steel fiber is optimal. While if impact toughness is critical, RPC with 3% steel fiber would be the best choice.

Sign in / Sign up

Export Citation Format

Share Document