scholarly journals Analysis of Some Mechanical Properties of Hybrid Matrix Composites Reinforced by Linen Fabric. Orthopaedic Applications

2021 ◽  
Vol 58 (3) ◽  
pp. 148-159
Author(s):  
Vlad Alexandru Georgeanu ◽  
Dumitru Bolcu ◽  
Marius Marinel Stanescu ◽  
Ion Ciuca ◽  
Victorita Stefanescu ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Composite Materials ◽  
Tensile Tests ◽  
Matrix Composites ◽  
Characteristic Curves ◽  
Elongation At Break ◽  
Fabric Reinforcement ◽  
Hybrid Matrix ◽  
Linen Fabric

Great interest has been shown lately in bio-composite materials because they are inexpensive and sustainable. Composites with matrices and natural reinforcers have been little studied. Here, we study certain mechanical properties of composite materials with a Dammar-based matrix (also named hybrid matrix) and flax fabric reinforcement. To be precise, we examine three types of resins where Dammar is the major component, with a volume proportion of 55%, 65% and 75%. In this respect, we have made composite materials reinforced by two types of flax fabric and we have measured the characteristic curves and some mechanical properties, such as the Young�s modulus, tensile strength and elongation at break using tensile tests. Based on the obtained properties, it is proposed or possible to use these materials in orthopedics.

The Effects of a Compatibilizer for Improving Mechanical Properties on Polymer Matrix Composites

2021 ◽  
Vol 877 ◽  
pp. 3-8
Author(s):  
Prathumrat Nuyang ◽  
Atiwat Wiriya-Amornchai ◽  
Watthanaphon Cheewawuttipong
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Impact Strength ◽  
Young’S Modulus ◽  
Polymer Matrix ◽  
Polymer Matrix Composites ◽  
Fine Powder ◽  
Matrix Composites ◽  
Elongation At Break ◽  
The Impact

The effect of compatibilizer agent was studied when adding Aluminum fine powder (Al) to reinforce in Polypropylene (PP) by compared between polymer matrix composites (PMCs) and PMCs added Polypropylene graft maleic anhydride (PP-g-MAH).The average particle size of the aluminum fine powder was around 75 μm filled in polypropylene with different proportions of 2.5, 5, 7.5 and 10wt%. PMCs were prepared using the internal mixer. The results found that when the amount of aluminum fine powder increased, the mechanical properties had changed, i.e., tensile strength, and Young’s Modulus increased, while the impact strength and elongation at break decreased. But, when adding compatibilizer 1wt% it was found that the trend of tensile strength, and Young’s Modulus increased that compared with non-compatibilizer, but the impact strength and elongation at break decreased. The part of the morphology of PMCs with non-compatibilizer was found that the particle of aluminum fine powder dispersed in the matrix phase, but there were many microvoids between filler and matrix. But, PMCs with compatibilizer caused the microvoids between filler and matrix to be reduced.

Physico-Mechanical Properties of Banana Fiber Reinforced Polymer Composite as an Alternative Building Material

2015 ◽  
Vol 650 ◽  
pp. 131-138 ◽  
Author(s):  
Himadri Das ◽  
Pallav Saikia ◽  
Dipul Kalita
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Composite Materials ◽  
Flexural Strength ◽  
Polymer Composite ◽  
Natural Fiber ◽  
Strength Properties ◽  
Banana Fiber ◽  
Elongation At Break ◽  
Ldpe Composites

Utilization of natural fiber as reinforcing material is the latest trend in polymer science to produce higher strength with lower weight composite materials having wide range of applications. As a natural fiber, banana fiber is getting importance in recent years in the reinforcement arena of polymer composite. Two species of banana vizMusa sapientumandMusa paradisicaavailable in North East India were selected considering their higher fiber yield and adequate strength properties of the fibers. The chemical compositions, spectroscopic and thermal properties of these fibers were studied in order to study their suitability for commercial exploration. Low density polyethylene (LDPE)-banana fiber reinforced composites were prepared using hydraulic hot press. Physico-mechanical properties (e.g. tensile strength, flexural strength, elongation at break, Young's modulus) of the prepared composites were determined. The tensile strengths and flexural strengths of the composites increased while using LDPE 10 to 30 % of the fiber and then started to decrease gradually. Young moduli of the composites increased with the increase of fiber mass. Water absorption also increased accordingly with the increase of the fiber weight. The elongation at break decreased with increasing fiber quantity. The mechanical strength properties of chemically treated banana fiber-LDPE composites were slightly higher than the mechanically extracted fiber-LDPE composites. Structural analyses of the treated fibers were carried out by FTIR and XRD. These studied revealed due to the removal of noncellulosic constituents such as hemicelluloses and lignin the crystalline properties of the fibers were increased. All the properties of composite like tensile strength, flexural strength, water absorption capacity etc. plays a significant role in these polymer composite materials. Hence it can be concluded that banana fiber can be used as reinforced agent successfully in the composite industry as a sustainable building material.

scholarly journals Manufacturing Technology of Some Impact Resistant Materials

2021 ◽  
Vol 44 (1) ◽  
pp. 54-58
Author(s):  
Iulian PĂDURARU ◽  
Vasile BRIA ◽  
Adrian CÎRCIUMARU
Keyword(s):  
Mechanical Properties ◽  
Composite Materials ◽  
Composite Structures ◽  
Impact Resistance ◽  
Polymeric Materials ◽  
Tensile Tests ◽  
Manufacturing Technology ◽  
Matrix Composites ◽  
Polymeric Matrix Composites ◽  
Key Parameter

In this paper impact resistance is a key parameter for composite materials. Composite structures can experience impact loads either accidentally in the designed life or in an anticipated hostile service environment. That is why the manufacturing technology is very important. For materials manufacture were established: the type of polymer matrix, the types of fabrics and additives which will be used to improve impact resistance and also analysis of mechanical properties of formed composite materials (bending and tensile tests). Knowledge of the mechanical properties of polymeric materials is necessary in all areas of their applicability. Thus, rigidity and mechanical strength are key properties for most applications in which polymeric matrix composites are used.

Mechanical and Morphology Properties of Polypropylene/ Nano-CaCO3 Composites

2013 ◽  
Vol 774-776 ◽  
pp. 625-628
Author(s):  
Teng Fei Shen ◽  
Fa Chao Wu
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Electron Microscope ◽  
Maleic Anhydride ◽  
Interfacial Adhesion ◽  
Tensile Tests ◽  
Melt Blending ◽  
Elongation At Break ◽  
High Fraction ◽  
Scanning Electron

To provide polypropylene (PP) with better excellent mechanical properties, nanoCaCO3 particles are incorporated into PP matrix by melt blending in this work. To improve the mophology between PP and nanoCaCO3, maleic-anhydride grafted PP (PP-g-MAH) was added as a compatibiliser. The results showed that PP-g-MAH indeed enhanced the interfacial adhesion of PP /nanoCaCO3 composites, which is demonstrated by the measurement of scanning electron microscope (SEM). The results of tensile tests revealed that the inclusion of nanoCaCO3 slightly increased modulus and decreased tensile strength and significantly increased the elongation at break. At high fraction of nanoCaCO3, the elongation at break was declined. The nanosized feature, shape and dispersion conditions of nanoCaCO3, played important roles in determining the performances of PP/nanoCaCO3 composites.

scholarly journals A Study of the Mechanical Properties of Composite Materials with a Dammar-Based Hybrid Matrix and Two Types of Flax Fabric Reinforcement

Polymers ◽  
2020 ◽  
Vol 12 (8) ◽  
pp. 1649
Author(s):  
Dumitru Bolcu ◽  
Marius Marinel Stănescu
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Composite Materials ◽  
Chemical Properties ◽  
Point Of View ◽  
Damping Factor ◽  
Hybrid Resin ◽  
Hybrid Matrix ◽  
Electron Microscopy Analysis ◽  
Specific Frequency

The need to protect the environment has generated, in the past decade, a competition at the producers’ level to use, as much as possible, natural materials, which are biodegradable and compostable. This trend and the composite materials have undergone a spectacular development of the natural components. Starting from these tendencies we have made and studied from the point of view of mechanical and chemical properties composite materials with three types of hybrid matrix based on the Dammar natural hybrid resin and two types of reinforcers made of flax fabric. We have researched the mechanical properties of these composite materials based on their tensile strength and vibration behavior, respectively. We have determined the characteristic curves, elasticity modulus, tensile strength, elongation at break, specific frequency and damping factor. Using SEM (Scanning Electron Microscopy) analysis we have obtained images of the breaking area for each sample that underwent a tensile test and, by applying FTIR (Fourier Transform Infrared Spectroscopy) and EDS (Energy Dispersive Spectroscopy) analyzes, we have determined the spectrum bands and the chemical composition diagram of the samples taken from the hybrid resins used as a matrix for the composite materials under study. Based on the results, we have suggested that these composite materials could be used in different fields of activity.

scholarly journals The Structure and Mechanical Properties of Hemp Fibers-Reinforced Poly(ε-Caprolactone) Composites Modified by Electron Beam Irradiation

2021 ◽  
Vol 11 (12) ◽  
pp. 5317
Author(s):  
Rafał Malinowski ◽  
Aneta Raszkowska-Kaczor ◽  
Krzysztof Moraczewski ◽  
Wojciech Głuszewski ◽  
Volodymyr Krasinskyi ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Electron Beam ◽  
Impact Strength ◽  
Flexural Modulus ◽  
Natural Fibers ◽  
High Energy ◽  
Electron Radiation ◽  
Elongation At Break ◽  
Hemp Fibers

The need for the development of new biodegradable materials and modification of the properties the current ones possess has essentially increased in recent years. The aim of this study was the comparison of changes occurring in poly(ε-caprolactone) (PCL) due to its modification by high-energy electron beam derived from a linear electron accelerator, as well as the addition of natural fibers in the form of cut hemp fibers. Changes to the fibers structure in the obtained composites and the geometrical surface structure of sample fractures with the use of scanning electron microscopy were investigated. Moreover, the mechanical properties were examined, including tensile strength, elongation at break, flexural modulus and impact strength of the modified PCL. It was found that PCL, modified with hemp fibers and/or electron radiation, exhibited enhanced flexural modulus but the elongation at break and impact strength decreased. Depending on the electron radiation dose and the hemp fibers content, tensile strength decreased or increased. It was also found that hemp fibers caused greater changes to the mechanical properties of PCL than electron radiation. The prepared composites exhibited uniform distribution of the dispersed phase in the polymer matrix and adequate adhesion at the interface between the two components.

scholarly journals Influence of Hydrostatic Extrusion on the Mechanical Properties of the Model Al-Mg Alloys

2021 ◽  
Author(s):  
Aleksandra Towarek ◽  
Wojciech Jurczak ◽  
Joanna Zdunek ◽  
Mariusz Kulczyk ◽  
Jarosław Mizera
Keyword(s):  
Mechanical Properties ◽  
Plastic Deformation ◽  
Tensile Strength ◽  
Microstructural Analysis ◽  
Tensile Tests ◽  
Hydrostatic Extrusion ◽  
Microstructure Formation ◽  
Initial State ◽  
Degree Of Deformation ◽  
Al Mg Alloys

AbstractTwo model aluminium-magnesium alloys, containing 3 and 7.5 wt.% of Mg, were subjected to plastic deformation by means of hydrostatic extrusion (HE). Two degrees of deformation were imposed by two subsequent reductions of the diameter. Microstructural analysis and tensile tests of the materials in the initial state and after deformation were performed. For both materials, HE extrusion resulted in the deformation of the microstructure—formation of the un-equilibrium grain boundaries and partition of the grains. What is more, HE resulted in a significant increase of tensile strength and decrease of the elongation, mostly after the first degree of deformation.

scholarly journals Effect of Moisture Content on the Processing and Mechanical Properties of a Biodegradable Polyester

Polymers ◽  
2021 ◽  
Vol 13 (10) ◽  
pp. 1616
Author(s):  
Vincenzo Titone ◽  
Antonio Correnti ◽  
Francesco Paolo La Mantia
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Moisture Content ◽  
Mechanical Testing ◽  
Hydrolytic Degradation ◽  
Slight Reduction ◽  
Biodegradable Polyester ◽  
Molding Process ◽  
Elongation At Break ◽  
Effect Of Moisture

This work is focused on the influence of moisture content on the processing and mechanical properties of a biodegradable polyester used for applications in injection molding. The pellets of the biodegradable polyester were exposed under different relative humidity conditions at a constant temperature before being compression molded. The compression-molded specimens were again placed under the above conditions before the mechanical testing. With all these samples, it is possible to determine the effect of moisture content on the processing and mechanical properties separately, as well as the combined effect of moisture content on the mechanical properties. The results obtained showed that the amount of absorbed water—both before processing and before mechanical testing—causes an increase in elongation at break and a slight reduction of the elastic modulus and tensile strength. These changes have been associated with possible hydrolytic degradation during the compression molding process and, in particular, with the plasticizing action of the moisture absorbed by the specimens.

scholarly journals Mimicking the Mechanical Properties of Aortic Tissue with Pattern-Embedded 3D Printing for a Realistic Phantom

Materials ◽  
2020 ◽  
Vol 13 (21) ◽  
pp. 5042
Author(s):  
Jaeyoung Kwon ◽  
Junhyeok Ock ◽  
Namkug Kim
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
3D Printing ◽  
Mechanical Characteristics ◽  
Aortic Wall ◽  
Tensile Tests ◽  
Human Aorta ◽  
Aortic Tissue ◽  
Medical Field ◽  
Base Materials

3D printing technology has been extensively applied in the medical field, but the ability to replicate tissues that experience significant loads and undergo substantial deformation, such as the aorta, remains elusive. Therefore, this study proposed a method to imitate the mechanical characteristics of the aortic wall by 3D printing embedded patterns and combining two materials with different physical properties. First, we determined the mechanical properties of the selected base materials (Agilus and Dragonskin 30) and pattern materials (VeroCyan and TPU 95A) and performed tensile testing. Three patterns were designed and embedded in printed Agilus–VeroCyan and Dragonskin 30–TPU 95A specimens. Tensile tests were then performed on the printed specimens, and the stress-strain curves were evaluated. The samples with one of the two tested orthotropic patterns exceeded the tensile strength and strain properties of a human aorta. Specifically, a tensile strength of 2.15 ± 0.15 MPa and strain at breaking of 3.18 ± 0.05 mm/mm were measured in the study; the human aorta is considered to have tensile strength and strain at breaking of 2.0–3.0 MPa and 2.0–2.3 mm/mm, respectively. These findings indicate the potential for developing more representative aortic phantoms based on the approach in this study.

Effect of Castor Oil Impregnation on the Physical and Mechanical Properties of Bacterial Cellulose

2012 ◽  
Vol 3 (1) ◽  
pp. 13-26
Author(s):  
Myrtha Karina ◽  
Lucia Indrarti ◽  
Rike Yudianti ◽  
Indriyati
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Bacterial Cellulose ◽  
Young’S Modulus ◽  
Castor Oil ◽  
Young's Modulus ◽  
Physical And Mechanical Properties ◽  
Scanning Electron Micrographs ◽  
Elongation At Break ◽  
Acetone Water

The effect of castor oil on the physical and mechanical properties of bacterial cellulose is described. Bacterial cellulose (BC) was impregnated with 0.5–2% (w/v) castor oil (CO) in acetone–water, providing BCCO films. Scanning electron micrographs revealed that the castor oil penetrated the pores of the bacterial cellulose, resulting in a smoother morphology and enhanced hydrophilicity. Castor oil caused a slight change in crystallinity indices and resulted in reduced tensile strength and Young's modulus but increased elongation at break. A significant reduction in tensile strength and Young's modulus was achieved in BCCO films with 2% castor oil, and there was an improvement in elongation at break and hydrophilicity. Impregnation with castor oil, a biodegradable and safe plasticiser, resulted in less rigid and more ductile composites.

Sign in / Sign up

Export Citation Format

Share Document