Stability of Ceramic Glazes Obtained by Valorification of Anorganic Pigments Extracted from Electroplating Sludge

2018 ◽  
Vol 69 (3) ◽  
pp. 571-574
Author(s):  
Mihaela Andreea Mitiu ◽  
Maria Iuliana Marcus ◽  
Maria Vlad ◽  
Cristina Mihaela Balaceanu

This paper presents the results of the research activity in order to etablish the stability and leaching potential of ceramic tiles which have been developed using glazes colored with pigments obtained by the extraction of chromium and iron metals from electroplating sludge. All these ceramic tiles contain various amounts of heavy metals in their glazes due to the pigments composition. The ceramic samples have been subjected to leaching tests in order to detect if various elements of relevance such as chromium, lead, cadmium, zinc or iron migrated to any great extent into test solutions. Leaching tests have been performed following the international standard SR ISO 10545-15 method for specific metals leaching into 4% acetic acid solutions at 220C after a 24h period and the international standard SR EN 12457/1-4 method with distilled water as leaching agent at LSR of 10 l/kg, for 24h period. Amounts of heavy metals have been negligible or non-detectable (iron) in the leaching solutions, being well below the limit values established by the legislation in force.

Pharmaceutics ◽  
2021 ◽  
Vol 13 (2) ◽  
pp. 271
Author(s):  
Lucía Yepes-Molina ◽  
José A. Hernández ◽  
Micaela Carvajal

Pomegranate extract (PG-E) has been reported to exert a protective effect on the skin due to its antioxidant activity. Ingredients rich in phenolic compounds are unstable in extract solutions, and, therefore, the use of a suitable nanosystem to encapsulate this type of extract could be necessary in different biotechnological applications. Thus, we investigated the capacity of Brassica oleracea L. (cauliflower) inflorescence vesicles (CI-vesicles) to encapsulate PG-E and determined the stability and the antioxidant capacity of the system over time. In addition, the protective effect against UV radiation and heavy metals in HaCaT cells was also tested. The CI-vesicles had an entrapment efficiency of around 50%, and accelerated stability tests did not show significant changes in the parameters tested. The results for the HaCaT cells showed the non-cytotoxicity of the CI-vesicles containing PG-E and their protection against heavy metals (lead acetate and mercuric chloride) and UV-B radiation through a reduction of oxidative stress. The reduction of the percentage of deleted mtDNA (mtDNA4977, “common deletion”) in UV-treated HaCaT cells due to the presence of CI-vesicles containing PG-E indicated the mechanism of protection. Therefore, the effects of CI-vesicles loaded with PG-E against oxidative stress support their utilization as natural cosmeceuticals to protect skin health against external damage from environmental pollution and UV radiation.


2011 ◽  
Vol 194-196 ◽  
pp. 2365-2375
Author(s):  
Jai Houng Leu ◽  
Li Fong Wu ◽  
Ay Su

This research investigated and explored the overall technical and legal suggestions on mixed ash (bottom ash + fly ash) from the first BOT(built-operation then transfer) incineration plant in south Taoyuan of Taiwan, with the hope of serving as the reference for treating ash from urban refuse incinerator and making sustainable operation management policies in Taiwan. Both bottom ash and fly ash contain high-content harmful metals like lead, chrome, and cadmium, with the lead content exceeding standard value. Plasma fusing technology may effectively settle toxic heavy metals and reduce their dissolution rate. The results show that the increase in percentage of bottom ash could maintain post-fusing strength and produce solidification effect, but this reduced the stability of toxic heavy metals and raised their dissolution rate. Suitable mixture ratio of bottom ash and fly ash was 2:1, volume reduction ratio 0.349, and weight reduction ratio 0.4936. The mixture was fulvous and dense with gloss and adequate strength. The dissolution test of lava products complied with national standards, and they might be used for recycling aggregates and solidifying cement.


2015 ◽  
Vol 73 (4) ◽  
pp. 890-898 ◽  
Author(s):  
Huimin Wu ◽  
Meng Li ◽  
Lei Zhang ◽  
Chao Sheng

Thermal hydrolysis (TH) has been used to improve anaerobic digestion performance as well as the stability of heavy metals in sludge. Because the toxicity of heavy metals is closely related to both the concentration and the chemical speciation, more exhaustive studies on speciation distribution are urgently needed. This research aimed to investigate the effects of TH treatment (especially the time and temperature) on the concentration and stability of heavy metals in sludge, and to define the optimal TH conditions. The TH experiment indicated that the content of the stable form of Cu and Zn reached 83% and 47.4%, respectively, with TH at 210°C and 30 min. Compared with the raw sludge, the proportion of Cu and Zn increased by 11.88% and 7.3%, respectively. Results indicated that the heavy metals were combined with sludge in a more stable form with the pretreatment of TH, which improved the stability of heavy metals.


2012 ◽  
Vol 65 (1) ◽  
pp. 76-99 ◽  
Author(s):  
K. Haarstad ◽  
H. J. Bavor ◽  
T. Mæhlum

A literature review shows that more than 500 compounds occur in wetlands, and also that wetlands are suitable for removing these compounds. There are, however, obvious pitfalls for treatment wetlands, the most important being the maintenance of the hydraulic capacity and the detention time. Treatment wetlands should have an adapted design to target specific compounds. Aquatic plants and soils are suitable for wastewater treatment with a high capacity of removing nutrients and other substances through uptake, sorption and microbiological degradation. The heavy metals Cd, Cu, Fe, Ni and Pb were found to exceed limit values. The studies revealed high values of phenol and SO4. No samples showed concentrations in sediments exceeding limit values, but fish samples showed concentrations of Hg exceeding the limit for fish sold in the European Union (EU). The main route of metal uptake in aquatic plants was through the roots in emergent and surface floating plants, whereas in submerged plants roots and leaves take part in removing heavy metals and nutrients. Submerged rooted plants have metal uptake potential from water as well as sediments, whereas rootless plants extracted metals rapidly only from water. Caution is needed about the use of SSF CWs (subsurface flow constructed wetlands) for the treatment of metal-contaminated industrial wastewater as metals are shifted to another environmental compartment, and stable redox conditions are required to ensure long-term efficiency. Mercury is one of the most toxic heavy metals and wetlands have been shown to be a source of methylmercury. Methyl Hg concentrations are typically approximately 15% of Hgt (total mercury). In wetlands polycyclic aromatic hydrocarbons (PAH), bisphenol A, BTEX, hydrocarbons including diesel range organics, glycol, dichlorodiphenyltrichloroethane (DDT), polychlorinated biphenyls (PCB), cyanide, benzene, chlorophenols and formaldehyde were found to exceed limit values. In sediments only PAH and PCB were found exceeding limit values. The pesticides found above limit values were atrazine, simazine, terbutylazine, metolachlor, mecoprop, endosulfan, chlorfenvinphos and diuron. There are few water quality limit values of these compounds, except for some well-known endocrine disrupters such as nonylphenol, phtalates, etc.


2002 ◽  
Vol 11 (4) ◽  
pp. 285-300 ◽  
Author(s):  
V. MÄNTYLAHTI ◽  
P. LAAKSO

Increasing concentrations of arsenic and heavy metals in agricultural soils are becoming a growing problem in industrialized countries. These harmful elements represent the basis of a range of problems in the food chain, and are a potential hazard for animal and human health. It is therefore important to gauge their absolute and relative concentrations in soils that are used for crop production. In this study the arsenic and heavy metal concentrations in 274 mineral soil samples and 38 organogenic soil samples taken from South Savo province in 2000 were determined using the aqua regia extraction technique. The soil samples were collected from 23 farms.The elements analyzed were arsenic, cadmium, chromium, copper, mercury, nickel, lead and zinc. The median concentrations in the mineral soils were:As 2.90 mg kg –1, Cd 0.084 mg kg –1, Cr 17.0 mg kg –1, Cu 13.0 mg kg –1, Hg 0.060 mg kg –1, Ni 5.4 mg kg –1, Pb 7.7 mg kg –1, Zn 36.5 mg kg –1. The corresponding values in the organogenic soils were:As 2.80 mg kg –1, Cd 0.265 mg kg –1, Cr 15.0 mg kg –1, Cu 29.0 mg kg –1, Hg 0.200 mg kg –1, Ni 5.9 mg kg –1, Pb 11.0 mg kg –1, Zn 25.5 mg kg –1. The results indicated that cadmium and mercury concentrations in the mineral and organogenic soils differed. Some of the arsenic, cadmium and mercury concentrations exceeded the normative values but did not exceed limit values. Most of the agricultural fields in South Savo province contained only small amounts of arsenic and heavy metals and could be classified as “Clean Soil”. A draft for the target values of arsenic and heavy metal concentrations in “Clean Soil” is presented.;


2012 ◽  
Vol 14 (1) ◽  
pp. 52
Author(s):  
Reginawanti Hindersah ◽  
Rija Sudirja

Azotobacter might be used as biological agents in bioremediation of heavy metal-contaminated soil since this rhizobacteria produceexopolysachharides (EPS) that mobilize soil heavy metals, and phytohormones that regulate root growth. So that heavy metal uptake bythe roots could be increased. The objective of this research was to verify the stability of EPS and phytohormones in Azotobacter liquidinoculants during four months in different temperature storage. Liquid inoculants has been produced in EPS-induced media and stored in200C and room temperature (24-270C) during four months. The results showed that the better temperature storage was room temperatureinstead of 20 0C since pH, total N, and EPS and phytohormones content was relatively stable during storage.


2019 ◽  
Vol 35 (5) ◽  
pp. 1508-1513
Author(s):  
Noura Yahya El Mehbad

This paper aims to investigate removal of aromatic and heavy metals compounds from fuels using cement kiln dust, and a cationic surfactant. The effect of a cationic surfactant and the composition of kiln dust on the stability of fuel was studied. The optimum conditions of adsorption were investigated. The stability of fuels was improved after adsorption because of the absorption of heavy metals, which act as catalysts. The concentrations of kiln dust and additives are effective for the absorption of heteroatoms of polar and nonpolar molecules. The addition of different concentrations of the cationic surfactant to kiln dust enhances the removal of polar molecules in fuel. The relation between the efficiency of the cationic surfactant and the enhanced removal of polar molecules was established. This study suggests a new mechanism to remove polar molecules according to the structure of the additive. Several parameters that affect the performance of the removal process were investigated under all optimum conditions. A complete chemical analysis of the fuels before and after treatment was performed, and the stability of the fuel was evaluated at different conditions. The prepared additive could enhance the oil quality and is environmentally safe. The adsorption behaviour of kiln dust was investigated to find a new mechanism of its efficiency. The results confirm the role of the cationic surfactant in the purification of fuels and the effectiveness of kiln dust in improving the stability of fuels, which depend on the concentration of the cationic surfactant and the nature of the kiln dust.


2021 ◽  
pp. 2947-2956
Author(s):  
Nazym Kozhanova ◽  
Nurzhan Sarsembayeva ◽  
Bozena Lozowicka ◽  
Zhassulan Kozhanov

Background and Aim: The quality of food, especially animal-based food, is crucial for human health. However, the quality of milk and other animal products has become an acute cause for concern in Kazakhstan . Technogenic dispersion of heavy metals (HMs) causes adverse effects on living organisms and creates unfavorable conditions for the existence of humans, animals, and plants. The purpose of this study was to analyze the content of several HMs in samples of soil, horse feed (hay, mixed feed, and bran), mare's milk, and manure to assess bioaccumulation and possible adverse effects on the bodies of horses. An additional purpose was to identify areas with acceptable conditions for obtaining environmentally safe horse breeding products in the agricultural zones of the Almaty region, Kazakhstan. Materials and Methods: Samples were obtained from two farms in the Almaty region in 2020 (spring, summer, and autumn). In total, 72 soil samples were analyzed, which were taken from the upper humus horizon to the depth of the arable layer. Eighty-six samples were taken from the feed of horses. Green feed was represented by perennial and annual grasses (alsike clover, Medicago sativa, sweet yellow clover, as well as pea and oat mix). Barley and wheat bran stored in the warehouses of the farm were sampled for the research as feed supplements. The mixed feed comprised components such as maize and sunflower. In addition, 46 samples of mare's milk and 28 samples of horse manure were collected. The HM analysis was performed in the laboratory of the Kazakh-Japanese Innovation Center. The residual amounts of HMs were determined using an absorption spectrometer with a voltammetric analyzer. The content of cadmium (Cd), lead (Pb), mercury (Hg), and arsenic (As) in all the studied samples of soil, feed, mare's milk, and manure did not exceed the threshold limit values (TLVs), suggesting that the intake of these toxic elements into the human body with food was low. Results: The average Cd concentration was in the range of 0.29-0.31 mg/kg in soil samples and in the range of 0.20-0.27 mg/kg in feed samples. In milk, the Cd concentration varied from 0.01 to 0.02 mg/L and was lower in summer and higher in fall. The total average Cd content in horse manure was 0.1844 mg/kg. The concentration of Pb in soil samples ranged from 1.09 to 1.30 mg/kg with the lowest value in spring and the highest in fall. In the feed, the concentration of Pb varied from 0.14 to 0.76 mg/kg and in milk from 0.03 to 0.15 mg/L. The average concentrations of Hg and As in soil samples averaged 0.022 and 0.019 mg/kg, respectively, and were within the TLVs. Conclusion: In the study areas, the calculated transition rates in the soil–feed–milk–manure system revealed that the greatest transition of HMs was observed for Pb and Cd, and a smaller migration was observed for Hg and As. The tendency of accumulation of trace elements continued in the feed.


2018 ◽  
Vol 26 (3) ◽  
pp. 233-238
Author(s):  
E. I. Popova

We conducted a complex investigation of anthropogenic roadside phytocoenoses. For the study, 8 plots (birch and pine forests) were selected, close to roads in the south of Tyumen region within the five administrative districts: Uporovsky, Zavodoukovsky, Yalutorovskiy, Yarkovsky, and Tobolsk. As a result of the studies, 75 species of vascular plants from 21 families were noted in the plant communities. It was found that the majority of the total projective cover of the plant communities was provided by synanthropic species. In the synanthropic fraction of the flora, 33 species belonging to 11 families were identified, those with the most species being: Scrophulariaceae, Compositeae, Rubiaceae, Poaceae, Fabaceae, Polygonaceae, Umbellíferae. The index of synanthropization of the flora of the studied phytocenoses is in the range from 43% to 64%. Among the identified pollutants accumulated in the phytocenoses, the group of heavy metals was identified (Cr, Cu, Ni, Pb, Sr, Zn). Needles of Pinus sylvestris L. mainly accumulate Cr, Cu, Ni, Sr. The greatest concentration of Pb and Zn was found in the leaves of Betula pendula Roth. The content of other heavy metals in the leaves of Betula pendula Roth. during the growing season was relatively stable. Accumulation of heavy metals in the studied components of forest ecosystems can be displayed structurally: soil > leaves < phytomass (birch forests), soil < needles > phytomass (pine forests). Methodological approaches to conducting a complex of long-term observations of natural ecosystems have been formulated, substantiated and justified. To evaluate the absorption efficiency of heavy metals, the biological absorption coefficient was calculated. The obtained results can be used as a control in the study of migration and accumulation of heavy metals and for assessing the degree of anthropogenic load on phytocenoses of roadside ecosystems and predict the extent of probable changes in them. The forecast of the results will facilitate the elaboration of a necessary system of measures aimed at increasing the stability of plant communities.


Sign in / Sign up

Export Citation Format

Share Document