Dämpfungsmaße in Lagerpassungen*/Identification of damping values for spindle bearing interfaces

2019 ◽  
Vol 109 (05) ◽  
pp. 342-346
Author(s):  
C. Brecher ◽  
T. Motschke ◽  
M. Fey
Keyword(s):  
Dynamic Simulation ◽  
State Of The Art ◽  
Mechanical Systems ◽  
Journal Bearings ◽  
Hertzian Contact ◽  
Analytical Models ◽  
Ball Bearings ◽  
The Past ◽  
Spindle Bearing ◽  
Stiffness And Damping

Die präzise Simulation mechanischer Systeme erfordert neben Steifigkeitswerten für Koppelelemente, die Kenntnis von Dämpfungswerten. Im Gegenteil zu Gleitlagern sind die physikalischen Effekte in Wälzlagern, die zur Energiedissipation führen, nur mit sehr großem rechnerischen Aufwand numerisch beschreibbar und experimentell validierte Modelle besitzen nur in engen Betriebsgrenzen Gültigkeit. Als Hauptdämpfungsquellen wurden bisher Kugel-Laufbahn-Kontakte sowie die Passungen der Lagerringe identifiziert. Letztere werden in diesem Beitrag untersucht. Ziel ist eine Aussage über Grenzen, innerhalb derer sich der Einfluss von Fugendämpfung bewegt   The dynamic simulation of mechanical systems requires reliable stiffness and damping values to enable meaningful results. Especially the inclusion of coupling elements into the simulation always leads to challenges regarding the interpretation of predicted results. Unlike journal bearings, there are no analytical models for roller and ball bearings that allow the prediction of damping values, whereas the prediction of stiffness values is already state of the art. In the past, the Hertzian contact as well as the bearing interfaces were identified as the main damping sources, but till today, no reliable models have been derived. This article deals therefore with a method to quantify the influence of bearing interface damping parameters.

A Macintosh Interface for the Cameca Camebax-Micro Electron Microprobe

1990 ◽  
Vol 48 (1) ◽  
pp. 438-439
Author(s):  
Carl E. Henderson
Keyword(s):  
Electron Microprobe ◽  
Processing Speed ◽  
Word Processing ◽  
State Of The Art ◽  
Computer Control ◽  
Third Party ◽  
Disk Storage ◽  
The Past ◽  
User Facility ◽  
Instrument Control

Over the past few years it has become apparent in our multi-user facility that the computer system and software supplied in 1985 with our CAMECA CAMEBAX-MICRO electron microprobe analyzer has the greatest potential for improvement and updating of any component of the instrument. While the standard CAMECA software running on a DEC PDP-11/23+ computer under the RSX-11M operating system can perform almost any task required of the instrument, the commands are not always intuitive and can be difficult to remember for the casual user (of which our laboratory has many). Given the widespread and growing use of other microcomputers (such as PC’s and Macintoshes) by users of the microprobe, the PDP has become the “oddball” and has also fallen behind the state-of-the-art in terms of processing speed and disk storage capabilities. Upgrade paths within products available from DEC are considered to be too expensive for the benefits received. After using a Macintosh for other tasks in the laboratory, such as instrument use and billing records, word processing, and graphics display, its unique and “friendly” user interface suggested an easier-to-use system for computer control of the electron microprobe automation. Specifically a Macintosh IIx was chosen for its capacity for third-party add-on cards used in instrument control.

Classifying the Past: Discriminant Analysis and its Application to Medieval Farming Systems

1996 ◽  
Vol 8 (1) ◽  
pp. 1-10 ◽  
Author(s):  
Ken Bartley
Keyword(s):  
Cluster Analysis ◽  
Discriminant Analysis ◽  
Processing Time ◽  
Farming Systems ◽  
Frame Of Reference ◽  
Analytical Models ◽  
Successful Implementation ◽  
Medieval Period ◽  
The Past ◽  
Livestock Management

This paper discusses the need for nationally based analytical models of the medieval period. The use of cluster analysis as a method for classifying demesne farms, by the crops they grew and their livestock management, is explained. Successful implementation of cluster analysis requires both the existence of a large base sample, to permit isolation of specific groupings within the data, and access to considerable processing time. The paper concludes by demonstrating how discriminant analysis can provide an efficient and systematic way of classifying even a single manor within a national frame of reference.

scholarly journals Improved design criterion for frictionally engaged contacts in overrunning clutches

2021 ◽  
Author(s):  
Nadine Nagler ◽  
Armin Lohrengel
Keyword(s):  
Design Process ◽  
Contact Area ◽  
Axial Load ◽  
State Of The Art ◽  
Tangential Force ◽  
Design Criterion ◽  
Hertzian Contact ◽  
Loss Of Function ◽  
Axial Loads ◽  
Improved Design

AbstractOverrunning clutches, also known as freewheel clutches, are frictionally engaged, directional clutches; they transmit torque depending on the Freewheel clutch rings’ rotation directions. The torque causes a tangential force in the Hertzian contact area. The hitherto “state-of-the-art design criterion” bases on this load situation. In practice, axial loads additionally act on the frictionally engaged Hertzian contact area. This additional axial load can cause the loss of the friction connection and so the freewheel clutch slips. This publication presents an improved design criterion for frictionally engaged contacts in freewheel clutches. It allows to consider tangential as well as axial loads during the design process. Additionally, it offers the possibility to estimate the probability of frictional engagement loss and gross slip based on the freewheel clutch’s application scenario. This publication points out how to use the improved design criterion to design freewheel clutches that are more robust against a loss of function.

scholarly journals Constitutive Models for the Tensile Behaviour of TRM Materials: Literature Review and Experimental Verification

Materials ◽  
2021 ◽  
Vol 14 (3) ◽  
pp. 700
Author(s):  
Maria Concetta Oddo ◽  
Giovanni Minafò ◽  
Lidia La Mendola
Keyword(s):  
State Of The Art ◽  
Constitutive Models ◽  
Stress Transfer ◽  
Theoretical Models ◽  
Tensile Tests ◽  
Analytical Models ◽  
Tensile Behaviour ◽  
Tensile Response ◽  
Textile Reinforced Mortar ◽  
Inorganic Matrix

In recent years, the scientific community has focused its interest on innovative inorganic matrix composite materials, namely TRM (Textile Reinforced Mortar). This class of materials satisfies the need of retrofitting existing masonry buildings, by keeping the compatibility with the substrate. Different recent studies were addressed to improve the knowledge on their mechanical behaviour and some theoretical models were proposed for predicting the tensile response of TRM strips. However, this task is complex due to the heterogeneity of the constituent materials and the stress transfer mechanism developed between matrix and fabric through the interface in the cracked stage. This paper presents a state-of-the-art review on the existing constitutive models for the tensile behavior of TRM composites. Literature experimental results of tensile tests on TRM coupons are presented and compared with the most relevant analytical models proposed until now. Finally, a new experimental study is presented and its results are used to further verify the reliability of the literature expressions.

scholarly journals Inflammation, epigenetics, and metabolism converge to cell senescence and ageing: the regulation and intervention

2021 ◽  
Vol 6 (1) ◽  
Author(s):  
Xudong Zhu ◽  
Zhiyang Chen ◽  
Weiyan Shen ◽  
Gang Huang ◽  
John M. Sedivy ◽  
...  
Keyword(s):  
Cell Fate ◽  
Cellular Response ◽  
State Of The Art ◽  
Cell Senescence ◽  
Therapeutic Interventions ◽  
Cell Fate Decision ◽  
The Past ◽  
Fate Decision ◽  
The Individual ◽  
Remarkable Progress

AbstractRemarkable progress in ageing research has been achieved over the past decades. General perceptions and experimental evidence pinpoint that the decline of physical function often initiates by cell senescence and organ ageing. Epigenetic dynamics and immunometabolic reprogramming link to the alterations of cellular response to intrinsic and extrinsic stimuli, representing current hotspots as they not only (re-)shape the individual cell identity, but also involve in cell fate decision. This review focuses on the present findings and emerging concepts in epigenetic, inflammatory, and metabolic regulations and the consequences of the ageing process. Potential therapeutic interventions targeting cell senescence and regulatory mechanisms, using state-of-the-art techniques are also discussed.

scholarly journals Security assurance cases—state of the art of an emerging approach

2021 ◽  
Vol 26 (4) ◽  
Author(s):  
Mazen Mohamad ◽  
Jan-Philipp Steghöfer ◽  
Riccardo Scandariato
Keyword(s):  
State Of The Art ◽  
Tool Support ◽  
Security Assurance ◽  
The Past ◽  
Depth Analysis ◽  
Structured Argumentation ◽  
Security Properties ◽  
Standards And Regulations ◽  
Assurance Cases ◽  
Security Standards

AbstractSecurity Assurance Cases (SAC) are a form of structured argumentation used to reason about the security properties of a system. After the successful adoption of assurance cases for safety, SAC are getting significant traction in recent years, especially in safety-critical industries (e.g., automotive), where there is an increasing pressure to be compliant with several security standards and regulations. Accordingly, research in the field of SAC has flourished in the past decade, with different approaches being investigated. In an effort to systematize this active field of research, we conducted a systematic literature review (SLR) of the existing academic studies on SAC. Our review resulted in an in-depth analysis and comparison of 51 papers. Our results indicate that, while there are numerous papers discussing the importance of SAC and their usage scenarios, the literature is still immature with respect to concrete support for practitioners on how to build and maintain a SAC. More importantly, even though some methodologies are available, their validation and tool support is still lacking.

scholarly journals The state of the art in soybean transcriptomics resources and gene coexpression networks

2021 ◽  
Author(s):  
Fabricio Almeida-Silva ◽  
Kanhu C Moharana ◽  
Thiago M Venancio
Keyword(s):  
State Of The Art ◽  
The State ◽  
Gene Coexpression Network ◽  
Rna Seq ◽  
Transcriptomic Data ◽  
The Past ◽  
Gene Coexpression ◽  
Genomics Research ◽  
Public Repositories ◽  
Coexpression Networks

Abstract In the past decade, over 3000 samples of soybean transcriptomic data have accumulated in public repositories. Here, we review the state of the art in soybean transcriptomics, highlighting the major microarray and RNA-seq studies that investigated soybean transcriptional programs in different tissues and conditions. Further, we propose approaches for integrating such big data using gene coexpression network and outline important web resources that may facilitate soybean data acquisition and analysis, contributing to the acceleration of soybean breeding and functional genomics research.

scholarly journals Mobility Method Applied to Calculate the Lubrication Properties of Bearing under Dynamic Loads

2013 ◽  
Vol 2013 ◽  
pp. 1-5 ◽  
Author(s):  
Tao He ◽  
Xiqun Lu ◽  
Jingzhi Zhu
Keyword(s):  
Dynamic Analysis ◽  
Mechanical Systems ◽  
Journal Bearings ◽  
Numerical Results ◽  
Dynamic Loads ◽  
Analysis Program ◽  
Computational Program ◽  
Dynamically Loaded ◽  
Mobility Method ◽  
Lubrication Properties

The analytical mobility method for dynamically loaded journal bearings was presented, with the intent to include it in a general computational program, such as the dynamic analysis program, that has been developed for the dynamic analysis of general mechanical systems. An illustrative example and numerical results were presented, with the efficiency of the method being discussed in the process of their presentation.

BIOMECHANICS OF WHEELCHAIR PROPULSION

2009 ◽  
Vol 09 (02) ◽  
pp. 229-242 ◽  
Author(s):  
CHIEN-JU LIN ◽  
PO-CHOU LIN ◽  
FONG-CHIN SU ◽  
KAI-NAN AN
Keyword(s):  
Upper Extremity ◽  
Modern Technology ◽  
Biomechanical Analysis ◽  
Daily Activities ◽  
Analytical Models ◽  
Wheelchair Propulsion ◽  
Mobility Impairments ◽  
Force Application ◽  
The Past

With progress of modern technology, manually-propelled wheelchairs are still of importance for individuals with mobility impairments. The repeated wheelchair propulsion and strenuous daily activities cause high loads and thus injuries on the upper extremity joints. Over the past few years, a considerable number of studies have been made on biomechanical analysis of wheelchair propulsion and wheelchair-related activities. Thorough investigation of biomechanics during wheelchair propulsion enhances comprehension of mechanism of injuries and provides information to improve wheelchair design and fitting. Numerous investigations have been made to demonstrate factors which cause low effectiveness of force application and inefficiency of movements. Emphasis was also placed on developing analytical models to simulate wheelchair propulsion.

Sign in / Sign up

Export Citation Format

Share Document