Analyzing Relationship between the Performance of the Fan and the Area of the Porous Thin Plate

2014 ◽  
Vol 488-489 ◽  
pp. 901-904
Author(s):  
Shu Lung Wang ◽  
Yueh Hua Wang
Keyword(s):  
Thin Plate ◽  
Static Pressure ◽  
Air Flow ◽  
Main Factors ◽  
The Difference ◽  
Better Than

The purpose of this research is to study the performance of axial fanof the porous thin plate. First, the area of the holes of the porous thin plate is changed to estimate the influence of the porous thin plate on the performance of the fan. This study is conducted by simulations and experiments to find out the factors that will impact the performance of the fan. The results show that if the area rate of the porous thin plate and the fan is smaller, the difference of the simulations and experiments will become greater. When the area rate is more than 80%, the difference of the simulations and experiments will turn to be 10% lower. The results of experiments show that the fan size and fan thickness are the two main factors that produce the influence on the porous thin plate. If the thickness of the bar of the porous thin plate is 2.0mm, the performance of the fan loss would be the smallest. As to the assembly position of the porous thin plate, unilateral assembly makes the performance of the fan better than bilateral assembly. This is in relation to the area size of the porous thin plate. Fan tray is bilateral assembled. The performance of the fan tray can be improved in the following two ways. To use the thicker fan as the static pressure is greater, or to use the fan with lower air flow as the loss will be lesser.

Unsteady Pressure Characteristics in the Mainstream/Disc Cavity of a Turbine-Stage

2017 ◽  
Author(s):  
A. V. Mirzamoghadam ◽  
J. Balasubramanian ◽  
M. Michael ◽  
R. P. Roy
Keyword(s):  
Flow Rate ◽  
Static Pressure ◽  
Cfd Simulation ◽  
Air Flow ◽  
Fast Response ◽  
Pressure Measurements ◽  
Turbine Stage ◽  
Unsteady Pressure ◽  
Purge Flow ◽  
The Difference

The interaction between the mainstream and disc cavity purge flows in a turbine stage is an unsteady 360° phenomenon. Most of the current rotating rigs have used steady pressure transducers to measure the mainstream annulus pressure distributions as well as the pressure distribution in the disc cavity. Unsteady static pressure measurements in these regions using fast-response transducers have also been reported but to a much lesser degree, mainly at ASU, OSU, VKI, and ETH. To gain better insight into the prevailing unsteady flow phenomena, and to assess the difference between steady and time-averaged unsteady pressure data, new unsteady static pressure measurements were recently carried out at three locations in an ASU-Honeywell turbine stage, namely, in the main gas path on the outer shroud near vane trailing edge as well as on the vane platform lip, and on the stator surface rim seal. They are reported in this paper along with the comparative results of the corresponding URANS CFD simulation reported in an earlier publication. Experiments were carried out at five different purge air flow conditions for each of the two mainstream air flow rate and rotor speed combinations. The current unsteady measurements indicate that the rim cavity pressure frequency is governed by the blade passage frequency. The unsteadiness amplitude increases with purge flow in the main gas path, but decreases with increase in purge flow for the rim cavity where the sensitivity to change in purge flow is smaller at the lower mainstream flow rate. The difference in the ambient-corrected time-averaged static pressures between those evaluated from the current unsteady measurements and the previously published steady measurements are found to be within the measurement uncertainties.

Removal of inelastically scattered electrons substantially increases phase contrast on frozen-hydrated molecules

1987 ◽  
Vol 45 ◽  
pp. 652-653
Author(s):  
John P. Langmore ◽  
Brian D. Athey
Keyword(s):  
Electron Diffraction ◽  
Phase Contrast ◽  
Low Dose ◽  
Dark Field ◽  
Biological Structure ◽  
Bright Field ◽  
Low Contrast ◽  
Negative Stain ◽  
The Difference ◽  
Better Than

Although electron diffraction indicates better than 0.3nm preservation of biological structure in vitreous ice, the imaging of molecules in ice is limited by low contrast. Thus, low-dose images of frozen-hydrated molecules have significantly more noise than images of air-dried or negatively-stained molecules. We have addressed the question of the origins of this loss of contrast. One unavoidable effect is the reduction in scattering contrast between a molecule and the background. In effect, the difference in scattering power between a molecule and its background is 2-5 times less in a layer of ice than in vacuum or negative stain. A second, previously unrecognized, effect is the large, incoherent background of inelastic scattering from the ice. This background reduces both scattering and phase contrast by an additional factor of about 3, as shown in this paper. We have used energy filtration on the Zeiss EM902 in order to eliminate this second effect, and also increase scattering contrast in bright-field and dark-field.

PENERAPAN MODEL PEMBELAJARAN KOOPERATIF TIPE STAD DENGAN PENDEKATAN RME UNTUK MENINGKATKAN HASIL BELAJAR MATEMATIKA SISWA KELAS IX SMP MUHAMMADIYAH PADANG LUAS KECAMATAN TAMBANG KABUPATEN KAMPAR

2018 ◽  
Vol 2 (5) ◽  
pp. 744
Author(s):  
Zainur Zainur
Keyword(s):  
Action Research ◽  
Cooperative Learning ◽  
Student Learning ◽  
Learning Outcomes ◽  
Mathematics Learning ◽  
Student Learning Outcomes ◽  
Learning Model ◽  
Research Instrument ◽  
The Difference ◽  
Better Than

This research was motivated by the low learning outcomes of grade IX SMP Muhammadiyah Padang LuasKecamatan Tambang Kabupaten Kampar. This study aims to improve learning outcomes in mathematicslearning through STAD type cooperative learning with the RME approach in class IX SMP MuhammadiyahPadang Luas Kecamatan Tambang Kabupaten Kampar. The subjects of this study were all classes IX in SMPMuhammadiyah Padang Luas Kecamatan Tambang Kabupaten Kampar totaling 26 people. The form ofresearch is classroom action research. This research instrument consists of performance instruments and datacollection instruments in the form of teacher activity observation sheets and activities. The results of the studystated that there were significant differences between students' mathematics learning outcomes before applyingthe STAD type cooperative learning model with the RME approach with after applying the STAD typecooperative learning model with the RME approach. The difference shows student learning outcomes after theaction is better than before the action with completeness reaching 80.77% or 21 completed. Based on the resultsof the study and discussion it can be concluded that the application of STAD type learning model with RealisticMathematic Education (RME) approach can improve the learning outcomes of grade IX students of SMPMuhammadiyah Padang Luas Kecamatan Tambang Kabupaten Kampar on statistical material.

scholarly journals Six ultraviolet minutes for cleaner operating theatres

2020 ◽  
Vol 30 (Supplement_5) ◽  
Author(s):  
R Bosco ◽  
S Gambelli ◽  
V Urbano ◽  
G Cevenini ◽  
G Messina
Keyword(s):  
Cross Sectional Study ◽  
Cross Sectional ◽  
Before And After ◽  
Operating Theatres ◽  
Cleaning Procedures ◽  
The Difference ◽  
Contamination Levels ◽  
Different Levels ◽  
Better Than ◽  
Final Cleaning

Abstract Background Sanitizing the operating theatres (OT) is important to minimize risk of post-operative infections. Disinfection procedures between one operation and another is less aggressive than final cleaning procedures, at the end of the day. Aim was assessing the difference of contamination: i) between different levels of disinfection; ii) before and after the use of a UVC Device (UVC-D). Methods Between December 2019/February 2020 a cross sectional study was conducted in OT in a real clinical context. 94 Petri dishes (PD) were used in 3 OT. Three different sanitation levels (SL1-3) were compared pre- and post-use of UVC-D: i) No cleaning after surgery (SL1); ii) after in-between cleaning (SL2); iii) after terminal cleaning (SL3). UVC-D was employed for 6 minutes, 3 minutes per bed side. PD were incubated at 36 °C and colony forming unit (CFU) counted at 48h. Descriptive statistic, Wilcoxon and Mann-Whitney tests were performed to assess the contamination levels in total, pre/post use of UVC-D, and between different sanitation levels, respectively. Results In total we had a mean of 3.39 CFU/PD (C.I. 2.05 - 4.74) and a median of 1 CFU/PD (Min. 0 - Max. 39), after UVC-D use we had a mean of 2.20 CFU/PD (C.I. 0.69 - 5.09) and a median of 0 CFU/PD (Min. 0 - Max. 133). The UVC-D led to a significant reduction of CFU (p < 0.001). Without UVC-D we had a significant CFU drop (p < 0.05) between SL1 and SL3. Using UVC-D, we observed significant reductions of contamination (p < 0.05) between SL3 and SL1. Comparing SL1 (median 0) post UVC-D use vs SL2 pre UVC-D use (median 0.5), and SL2 post UVC-D use (median 0) vs SL3 pre UVC-D use (median 1) we had a significant reduction of contamination (p < 0.05). Conclusions UVC-D improved environmental contamination in any of the three sanitation levels. Furthermore, the use of UVC-D alone was better than in-between and terminal cleaning. Although these encouraging results, the cleaning procedures executed by dedicated staff has to be considered. Key messages UVC are efficient to decrease contamination in operating theatres regardless of sanitation levels. The additional use of UVC technology to standard cleaning procedures significantly improves sanitation levels.

Influence of Collagen Status on Microstructures of Porous Collagen/TCP Composites

2007 ◽  
Vol 330-332 ◽  
pp. 495-498
Author(s):  
Chao Zou ◽  
Wen Jian Weng ◽  
Xu Liang Deng ◽  
Kui Cheng ◽  
Pi Yi Du ◽  
...  
Keyword(s):  
Tissue Engineering ◽  
Cell Growth ◽  
Tricalcium Phosphate ◽  
Freeze Drying ◽  
Alkali Treatment ◽  
Test Results ◽  
Collagen Matrices ◽  
The Difference ◽  
Porous Composites ◽  
Better Than

Two starting collagens, sponge and floc collagen, were used to prepare collagen/tricalcium phosphate (TCP) composites. The resulting composites were porous and had 200μm pore size. However, there was a difference in the microstructure of the pore walls for the composites derived from the two collagens, the pore walls in sponge collagen/TCP composite were still porous and had 200 nm micropores size, TCP particles were trapped in collagen matrices. While floc collagen/TCP composite had smooth and dense walls in which TCP particles were embedded. The difference could be attributed to the starting collagen with different status. Sponge collagen has a soft structure, which easily becomes disassembled fibrils during alkali treatment, the disassembled fibrils are integrated again to form a dense morphology for pore walls after freeze-drying. While floc collagen has already a low disassembly degree, the alkali treatment could not be able to separate the fibrils, this remains as micropores in pore walls after freeze-drying. Both porous composites are significant in bone tissue engineering or regeneration. MTT test results showed the two composites had good cytocompatibility, and sponge collagen/TCP composite was somewhat better than floc collagen/TCP composite, which could result from that micropores derived roughness in pore walls of sponge collagen/TCP composite is suitable for cell growth.

Assessment of different selective agar media for enumeration and isolation ofListeriafrom dairy products

1988 ◽  
Vol 55 (4) ◽  
pp. 579-583 ◽  
Author(s):  
Lucas Dominguez ◽  
José Francisco Fernández ◽  
Victor Briones ◽  
José Luis Blanco ◽  
Guillermo Suárez
Keyword(s):  
Dairy Products ◽  
Agar Medium ◽  
Raw Milk ◽  
Superior Performance ◽  
Direct Plating ◽  
Selective Agar ◽  
Natural Microflora ◽  
Agar Media ◽  
The Difference ◽  
Better Than

SummaryDifferent selective agar media were compared for the recovery and isolation of five species ofListeriafrom raw milk and cheese. The selective media examined were Beerens medium, MacBride medium and that described by Dominguezet al.(1984) with 6 mg/1 acriflavine, listeria selective agar medium (LSAM), and LSAM with 12 mg/1 acriflavine (LSAM × 2A); a non-selective yeast glucose Lemco agar was included for comparison. When the difference between listeria and the natural microflora of raw milk and cheese was 102cfu/ml, listeria could be isolated by direct plating on all media tested. When it was lower than 103–104cfu/ml, listeria were isolated by direct plating only on LSAM and LSAM × 2A. When the difference was greater than 104cfu/ml, a previous enrichment was necessary to isolate them. LSAM and LSAM × 2A media performed better than the other media tested for isolating listeria by direct plating and improved their isolation from dairy products. This superior performance was evaluated by the ability of these media to support colony formation of different species ofListeriatested, the easy recognition of these colonies from those formed by other microorganisms and by their capacity to inhibit the natural microflora of these foods.

Distinction between Dolus and Culpa with reference to Arson in Zakon Sudnyj LJudem, the Vinodol Law and the Statute of Senj

De Jure ◽  
2021 ◽  
Vol 12 (1) ◽  
Author(s):  
Daniel Haman ◽  
◽  
◽  
Keyword(s):  
Criminal Law ◽  
The Other ◽  
Legal Documents ◽  
The Third ◽  
Other Hand ◽  
Criminal Offenses ◽  
The World ◽  
The Difference ◽  
Different Levels ◽  
Better Than

The difference between intent (dolus) and negligence (culpa) was rarely emphasized in codified medieval laws and regulations. When compared to the legal statements related to intent, negligence was mentioned even more rarely. However, there are some laws that distinguished between the two concepts in terms of some specific crimes, such as arson. This paper draws attention to three medieval Slavic legal documents – the Zakon Sudnyj LJudem (ZSLJ), the Vinodol Law and the Statute of Senj. They are compared with reference to regulations regarding arson, with the focus being on arson as a crime committed intentionally or out of negligence. The ZSLJ as the oldest known Slavic law in the world shows some similarities with other medieval Slavic legal codes, especially in the field of criminal law, since most of the ZSLJ’s articles are related to criminal law. On the other hand, the Vinodol Law is the oldest preserved Croatian law and it is among the oldest Slavic codes in the world. It was written in 1288 in the Croatian Glagolitic script and in the Croatian Chakavian dialect. The third document – the Statute of Senj – regulated legal matters in the Croatian littoral town of Senj. It was written in 1388 – exactly a century after the Vinodol Law was proclaimed. When comparing the Vinodol Law and the Statute of Senj with the Zakon Sudnyj LJudem, there are clear differences and similarities, particularly in the field of criminal law. Within the framework of criminal offenses, the act of arson is important for making a distinction between intent and negligence. While the ZSLJ regulates different levels of guilt, the Vinodol Law makes no difference between dolus and culpa. On the other hand, the Statute of Senj strictly refers to negligence as a punishable crime. Even though the ZSLJ is almost half a millennium older than the Statute of Senj and around 400 years older than the Vinodol Law, this paper proves that the ZSLJ defines the guilt and the punishment for arson much better than the other two laws.

Modification of Speech Discrimination in Patients with Binaural Asymmetrical Hearing Loss

1971 ◽  
Vol 36 (2) ◽  
pp. 208-212 ◽  
Author(s):  
Herbert J. Arkebauer ◽  
George T. Mencher ◽  
Carol McCall
Keyword(s):  
Hearing Loss ◽  
Sound Field ◽  
Combined Effect ◽  
Speech Signals ◽  
Speech Discrimination ◽  
The Difference ◽  
Better Than

Ten patients with bilateral asymmetrical hearing losses were tested for differences in speech discrimination scores under the following listening conditions: poorer ear under earphone; better ear under earphone; sound field, ears unoccluded; and sound field, poorer ear occluded. A patient manifesting a bilateral asymmetrical hearing loss may not be able to either separate or integrate two speech signals; however, occlusion of the poorer ear may be an advantageous means of obtaining maximum speech discrimination. Examination of the speech discrimination scores indicates the existence of detrimental interaction between ears exhibiting bilateral asymmetrical hearing loss. These findings also indicate that when the difference between ears is greater, speech discrimination is better than when asymmetry approximates symmetry. Apparently, the greater the impairment in the better ear, the greater the results to be gained by occluding the poorer ear. These findings were interpreted as being relevant in determining candidacy for binaural amplification. Such candidacy should be determined on the basis of speech discrimination scores obtained from each ear independently, and the combined effect of both aids.

TRUE AND APPARENT METABOLIZABLE ENERGY VALUES FOR POULTRY OF CANADIAN WHEATS AND OATS MEASURED BY BIOASSAY AND PREDICTED FROM PHYSICAL AND CHEMICAL DATA

1977 ◽  
Vol 57 (2) ◽  
pp. 365-374 ◽  
Author(s):  
I. R. SIBBALD ◽  
K. PRICE
Keyword(s):  
Metabolizable Energy ◽  
Chemical Data ◽  
Accuracy And Precision ◽  
Apparent Metabolizable Energy ◽  
The Difference ◽  
Variation Explained ◽  
Predicted Values ◽  
Naked Oats ◽  
Physical And Chemical ◽  
Better Than

Thirty samples of wheat and 28 samples of oats were assayed for true and apparent metabolizable energy (TME, AME). Within grains, the difference TME−AME increased with decreasing AME values; there is evidence that this trend is associated with reduced voluntary consumption of AME assay diets containing low energy grains. The TME and AME data were compared with ME values predicted from physical and chemical data describing the grains. Previously published prediction equations were tested and new equations were derived. Comparisons between predicted and observed data suggested that both the TME and AME values of wheat were predicted with insufficient accuracy and precision for practical use. Similar comparisons using the oat data showed high correlations between observed and predicted values, although the predictions were no more accurate than for wheat; however, when data describing four samples of naked oats were removed, the correlations were reduced substantially. Comparisons involving data for the hulled oats indicated that most equations were able to predict AME better than TME. Multiple regression analysis was used to identify those combinations of variables best able to predict TME data. No combination of variables was best for both wheat and oats. The combinations of variables used in published equations performed quite well. With four variables, the percentage of the TME variation explained was as high as 52 for wheat, 82 for oats and 64 for hulled oats. Predictions based on air-dry data are associated with higher correlations than those based on dry matter data, but the air-dry predictions are the less useful in practice. The reason for this is discussed.

LACTATION PERFORMANCE OF RANGE BEEF AND DAIRY-BEEF COWS

1984 ◽  
Vol 64 (2) ◽  
pp. 253-265 ◽  
Author(s):  
SARAH BUTSON ◽  
R. T. BERG
Keyword(s):  
Milk Production ◽  
Beef Cows ◽  
Significant Decline ◽  
Lactation Performance ◽  
University Of Alberta ◽  
Brown Swiss ◽  
Percent Protein ◽  
The Difference ◽  
The University ◽  
Better Than

A milking experiment with range, single-suckled beef cows was conducted over two lactations in 1976 and 1977 at the University of Alberta Research Ranch. A total of 428 cows were milked, ranging from 2 to 10 yr of age and representing four breed groups of Herefords and crossbreds of traditional beef and dairy breeds. Measurements of milk were taken in June and September each year. Milk was extracted following an intrajugular injection of 20 IU of oxytocin. Samples were analyzed for butterfat percent, protein percent and lactose percent. Age and breed of dam differences in milk yields, constituent percentages and yields were assessed. Least squares means of yields pooled over the two periods each year indicated that dams with Holstein and Brown Swiss breeding (DS) yielded more milk than beef crossbreds and purebred Herefords. Average milk yields estimated over 24 h ranged from 5.7 kg/day for Herefords to 7.8 kg/day for DS dams. Compared to 2-yr olds at 100%, 3-yr olds produced 125%, 4-yr olds 136% and mature cows 139% greater yield. The difference between June and September yields was evident between breed groups. Hereford milk production exhibited the greatest decline over 87 days compared to all other crossbreds and DS were the most persistent. Mature cows maintained milk yields better than younger cows, and 2-yr old milk yields declined most noticeably. All crossbred groups produced less butterfat percent and lactose percent content than the Herefords, yet yielded more total energy. All constituent percentages were higher than those reported for commercial dairy cattle. All constituent percentages increased significantly from June to September at approximately 130 days in lactation. A significant decline was noted for all constituent yields in September. Dairy crossbreds demonstrated the highest persistency for all constituent yields. Beef Synthetic dams were intermediate in yield persistency. Average milk yields had negative (P < 0.05) correlations with average constituent percentages. Inter-correlations among constituent percentages were variable and generally small and negative. Key words: Lactation, range cows

Sign in / Sign up

Export Citation Format

Share Document