Using Recycled Rubber Particles as Filler of Polymers

2014 ◽  
Vol 616 ◽  
pp. 260-267 ◽  
Author(s):  
Petr Valášek ◽  
Miroslav Müller ◽  
Juraj Ružbarský
Keyword(s):  
Mechanical Properties ◽  
Polymeric Materials ◽  
Epoxy Adhesive ◽  
Rubber Waste ◽  
Waste Rubber ◽  
Rubber Particles ◽  
Recycled Rubber ◽  
Material Utilization

One of a way of a material utilization of a rubber waste originated at a recyclation of tyres is its inclusion into polymeric materials. The paper describes chosen mechanical properties of an epoxy adhesive and polyurethane filled with the waste rubber. The waste rubber was gained as one of outputs of a recycling line of a firm Gumoeko, Ltd. The filler presence influences resultant mechanical properties and decreases a price of gained materials. Defining of mechanical properties enables to specify possible application areas.

Mechanical Properties of Surface Mortar with Waste Crumb Rubber

2014 ◽  
Vol 584-586 ◽  
pp. 917-920
Author(s):  
Gang Xue ◽  
Chun Feng Wu
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Rubber Particle ◽  
Impact Resistance ◽  
Crumb Rubber ◽  
Application Performance ◽  
Waste Rubber ◽  
Aging Properties ◽  
Rubber Particles ◽  
Waste Crumb Rubber

Applying modified waste rubber particle to surface mortar can give full play of the unique characteristics to utilize the waste and decrease environmental pollution. In order to study the application performance of crumb rubber mortar, five different mortar proportions are selected to determine the compressive strength, flexural strength, impact strength and thermal aging strength. The results show that rubber particles mortar possess excellent toughness, impact resistance and heat aging properties.

Effects of Rubber Particles on Rheological and Mechanical Properties of Concrete Containing CaCO3 Nanoparticles

2018 ◽  
Vol 926 ◽  
pp. 109-114
Author(s):  
Li Wang ◽  
Ben Dong Zhao
Keyword(s):  
Mechanical Properties ◽  
Fine Aggregate ◽  
Rubberized Concrete ◽  
Cement Pastes ◽  
Effective Strategies ◽  
Waste Rubber ◽  
Fine Aggregates ◽  
Strength Tests ◽  
Rubber Particles ◽  
Compressive And Flexural Strengths

Lots of waste rubber is being produced in the world and the utilization of it not only mitigate environmental impacts caused by waste rubber disposal but also enhance sustainable development. As a result, rubberized concrete, by incorporation of waste rubber into concrete, should be considered as one of the effective strategies to take advantage of waste rubber. However, problems such as low strengths, weak adhesion between rubber particles and cement pastes, and undesirable pore structures associated with rubberized concrete should be pay more attention to. In this study, the effect of replacement fine aggregate with rubber particles on rheological and mechanical properties of concrete containing CaCO3 nanoparticles was examined through slump, compressive and flexural strength tests. Rubber particles were employed to replace the fine aggregate equally by volume while CaCO3 nanoparticles were used as an equal part of binder by weight. Different sizes and volume contents of rubber particles were evaluated as well as different weight contents of CaCO3 nanoparticles. In addition, corresponding tests were also performed to evaluate the effect of CaCO3 nanoparticles in comparison to concrete specimens without CaCO3 nanoparticles. The results showed that replacement fine aggregates with rubber particles had some influence on the mechanical properties of rubberized concrete, resulting in undesirable findings in terms of compressive and flexural strengths. However, the incorporation of CaCO3 nanoparticles improved mechanical properties of rubberized concrete. Regarding slump test, the rubberized concrete without CaCO3 nanoparticles showed better performance. Considering rheological and mechanical properties, rubberized concrete with 1% CaCO3 nanoparticles presented acceptable results.

Thermoplastic Elastomers Based on Waste Rubber and Plastics

2004 ◽  
Vol 77 (3) ◽  
pp. 569-578 ◽  
Author(s):  
R. S. Rajeev ◽  
S. K. De
Keyword(s):  
Thermoplastic Elastomers ◽  
Waste Plastics ◽  
Rubber Latex ◽  
Elongation At Break ◽  
Rubber Waste ◽  
Waste Rubber ◽  
Rubber Tire ◽  
Rubber Phase ◽  
Recycled Rubber ◽  
Waste Polymer

Abstract This paper reviews the utilization of waste rubber and waste plastics for the preparation of thermoplastic elastomers (TPEs). TPEs based on ground rubber tire (GRT), waste EPDM rubber, waste nitrile rubber, recycled rubber, latex waste, and waste plastics are described with respect to composition and physical properties. It is found that part of the rubber phase or plastics phase or both in the rubber-plastics blend can be replaced with corresponding waste polymer for the preparation of thermoplastic elastomers. In many cases, the materials prepared from waste polymers show properties comparable to those prepared from fresh polymers. However, in some cases, the materials prepared from waste rubber or waste plastics cannot be classified as TPEs, as the blend compositions show very low elongation at break. Modification of the waste polymer or the use of compatibilizers result in stronger composites.

scholarly journals Mechanical Behavior of Plaster Composites Based on Rubber Particles from End-of-Life Tires Reinforced with Carbon Fibers

Materials ◽  
2021 ◽  
Vol 14 (14) ◽  
pp. 3979
Author(s):  
Rafael Vicente Lozano-Díez ◽  
Óscar López-Zaldívar ◽  
Sofía Herrero-del-Cura ◽  
Pablo Luís Mayor-Lobo ◽  
Francisco Hernández-Olivares
Keyword(s):  
Mechanical Properties ◽  
End Of Life ◽  
Carbon Fibers ◽  
Dynamic Modulus ◽  
Mechanical Performance ◽  
Rubber Waste ◽  
Rubber Particles ◽  
Mechanical Tensile ◽  
Microstructure Of The Material ◽  
Moduli Of Elasticity

The principal objective of this research project is the disposal of end-of-life tire rubber waste and its incorporation in gypsum composites. As a continuation of previous projects, which established a reduction in the mechanical properties of the resulting products, the behavior of these composites is analyzed with the incorporation of carbon fibers. The density, Shore C hardness, flexural strength, compressive strength, dynamic modulus of elasticity, strength–strain curves, toughness and resistance values and microstructure of the material are studied and compared. The results obtained show a significant increase in the mechanical tensile strength of all of the samples containing fibers. The moduli of elasticity results show a decrease in rigidity and increase in toughness and resistance of the material produced by incorporating the fibers. An optimum dosage of a water/gypsum ratio of 0.6 and incorporation of 1.5% carbon fibers is proposed. This lightweight material, which offers a high mechanical performance, features characteristics which are suitable for large prefabricated building elements in the form of panels or boards.

scholarly journals Mechanical and Fresh Properties of Multi-Binder Geopolymer Mortars Incorporating Recycled Rubber Particles

2021 ◽  
Vol 6 (10) ◽  
pp. 146
Author(s):  
Ahmed Abdelmonim ◽  
Dan V. Bompa
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Cement Mortar ◽  
Sodium Metasilicate ◽  
Degradation Model ◽  
Granulated Blast Furnace Slag ◽  
Embodied Carbon ◽  
Wide Range ◽  
Rubber Particles ◽  
Recycled Rubber

This paper examines the performance of multi-binder conventional geopolymer mixes (GCMs) with relatively high early strength, achieved through curing at ambient temperature. Mixes incorporating ground granulated blast-furnace slag (GGBS), fly ash (FA) and microsilica (MS) and sodium metasilicate anhydrous, were assessed in terms of workability, mechanical properties and embodied carbon. A cement mortar was also prepared for the sake of comparison. The best performing GCM was then used as a reference for rubberised geopolymer mixes (RuGM) in which the mineral aggregates were replaced by recycled rubber particles in proportions up to 30% by volume. Experimental results were combined with embodied carbon estimations in a multi-criteria assessment to evaluate the performance of each material. A mix with a 75/25 GGBS-to-FA ratio, in which 5% MS was added, had the best performance in terms of strength, workability, water absorption and environmental impact. The compressive strength was above 50 MPa, similar to that of the cement mortar. The latter had significantly higher embodied carbon, with factors ranging between 3.48 to 4.20, compared with the CGM mixes. The presence of rubber particles reduced the mechanical properties of RuGM proportionally with the rubber amount, but had similar workability and embodied carbon to CGMs. Finally, a strength degradation model is validated against the tests from this paper and literature to estimate the compressive strength of RuGM, providing reliable predictions over a wide range of rubber contents.

Possibilities of using biodegradable polymeric materials in the agricultural sector

2020 ◽  
Vol 67 (2) ◽  
pp. 115-120
Author(s):  
Raisa A. Alekhina ◽  
Victoriya E. Slavkina ◽  
Yuliya A. Lopatina
Keyword(s):  
Mechanical Properties ◽  
Biodegradable Polymers ◽  
Biodegradable Polymer ◽  
Agricultural Sector ◽  
Polymeric Materials ◽  
Polymer Materials ◽  
Limiting Factors ◽  
Research Purpose ◽  
Biodegradable Materials ◽  
Advantages And Disadvantages

The article presents options for recycling polymers. The use of biodegradable materials is promising. This is a special class of polymers that can decompose under aerobic or anaerobic conditions under the action of microorganisms or enzymes forming natural products such as carbon dioxide, nitrogen, water, biomass, and inorganic salts. (Research purpose) The research purpose is in reviewing biodegradable materials that can be used for the manufacture of products used in agriculture. (Materials and methods) The study are based on open information sources containing information about biodegradable materials. Research methods are collecting, studying and comparative analysis of information. (Results and discussion) The article presents the advantages and disadvantages of biodegradable materials, mechanical properties of the main groups of biodegradable polymers. The article provides a summary list of agricultural products that can be made from biodegradable polymer materials. It was found that products from the general group are widely used in agriculture. Authors have found that products from a special group can only be made from biodegradable polymers with a controlled decomposition period in the soil, their use contributes to increasing the productivity of crops. (Conclusions) It was found that biodegradable polymer materials, along with environmental safety, have mechanical properties that allow them producing products that do not carry significant loads during operation. We have shown that the creation of responsible products (machine parts) from biodegradable polymers requires an increase in their strength properties, which is achievable by creating composites based on them. It was found that the technological complexity of their manufacture and high cost are the limiting factors for the widespread use of biodegradable polymers at this stage.

scholarly journals Anti-Inflammatory Properties of Injectable Betamethasone-Loaded Tyramine-Modified Gellan Gum/Silk Fibroin Hydrogels

Biomolecules ◽  
2020 ◽  
Vol 10 (10) ◽  
pp. 1456
Author(s):  
Isabel Matos Oliveira ◽  
Cristiana Gonçalves ◽  
Myeong Eun Shin ◽  
Sumi Lee ◽  
Rui Luis Reis ◽  
...  
Keyword(s):  
Rheumatoid Arthritis ◽  
Mechanical Properties ◽  
Silk Fibroin ◽  
Therapeutic Efficacy ◽  
Composite Structures ◽  
Gelation Time ◽  
Polymeric Materials ◽  
Gellan Gum ◽  
Traditional Use

Rheumatoid arthritis is a rheumatic disease for which a healing treatment does not presently exist. Silk fibroin has been extensively studied for use in drug delivery systems due to its uniqueness, versatility and strong clinical track record in medicine. However, in general, natural polymeric materials are not mechanically stable enough, and have high rates of biodegradation. Thus, synthetic materials such as gellan gum can be used to produce composite structures with biological signals to promote tissue-specific interactions while providing the desired mechanical properties. In this work, we aimed to produce hydrogels of tyramine-modified gellan gum with silk fibroin (Ty–GG/SF) via horseradish peroxidase (HRP), with encapsulated betamethasone, to improve the biocompatibility and mechanical properties, and further increase therapeutic efficacy to treat rheumatoid arthritis (RA). The Ty–GG/SF hydrogels presented a β-sheet secondary structure, with gelation time around 2–5 min, good resistance to enzymatic degradation, a suitable injectability profile, viscoelastic capacity with a significant solid component and a betamethasone-controlled release profile over time. In vitro studies showed that Ty–GG/SF hydrogels did not produce a deleterious effect on cellular metabolic activity, morphology or proliferation. Furthermore, Ty–GG/SF hydrogels with encapsulated betamethasone revealed greater therapeutic efficacy than the drug applied alone. Therefore, this strategy can provide an improvement in therapeutic efficacy when compared to the traditional use of drugs for the treatment of rheumatoid arthritis.

scholarly journals Mechanical and Morphological Properties of Bio-Phenolic/Epoxy Polymer Blends

Molecules ◽  
2021 ◽  
Vol 26 (4) ◽  
pp. 773
Author(s):  
Ahmad Safwan Ismail ◽  
Mohammad Jawaid ◽  
Norul Hisham Hamid ◽  
Ridwan Yahaya ◽  
Azman Hassan
Keyword(s):  
Mechanical Properties ◽  
Phase Separation ◽  
Polymer Blends ◽  
Epoxy Polymer ◽  
Flexural Modulus ◽  
Polymeric Materials ◽  
Morphological Properties ◽  
Comparison Results ◽  
Unique Material ◽  
Different Types

Polymer blends is a well-established and suitable method to produced new polymeric materials as compared to synthesis of a new polymer. The combination of two different types of polymers will produce a new and unique material, which has the attribute of both polymers. The aim of this work is to analyze mechanical and morphological properties of bio-phenolic/epoxy polymer blends to find the best formulation for future study. Bio-phenolic/epoxy polymer blends were fabricated using the hand lay-up method at different loading of bio-phenolic (5 wt%, 10 wt%, 15 wt%, 20 wt%, and 25 wt%) in the epoxy matrix whereas neat bio-phenolic and epoxy samples were also fabricated for comparison. Results indicated that mechanical properties were improved for bio-phenolic/epoxy polymer blends compared to neat epoxy and phenolic. In addition, there is no sign of phase separation in polymer blends. The highest tensile, flexural, and impact strength was shown by P-20(biophenolic-20 wt% and Epoxy-80 wt%) whereas P-25 (biophenolic-25 wt% and Epoxy-75 wt%) has the highest tensile and flexural modulus. Based on the finding, it is concluded that P-20 shows better overall mechanical properties among the polymer blends. Based on this finding, the bio-phenolic/epoxy blend with 20 wt% will be used for further study on flax-reinforced bio-phenolic/epoxy polymer blends.

Sign in / Sign up

Export Citation Format

Share Document