Impact of Anisotropy on the Elastic Modulus of Basic Woven Fabric Structure

2015 ◽  
Vol 732 ◽  
pp. 123-126
Author(s):  
Diana Šimić Penava ◽  
Željko Penava ◽  
Željko Knezić
Keyword(s):  
Elastic Modulus ◽  
Tensile Force ◽  
Woven Fabrics ◽  
Raw Material ◽  
Woven Fabric ◽  
Weft Direction ◽  
Fabric Structure ◽  
Tensile Forces ◽  
Extension Direction ◽  
Good Agreement

Anisotropy is the characteristic which is typical for most materials, especially woven fabrics. Influence of direction of tensile force action on the properties of the fabric is big and frequently tested. The woven fabric can be defined as orthogonal elastomer. The values of elastic modulus of woven fabrics for different angles of extension direction were analyzed. Three types of fabric samples of different weaves (plain, twill, sateen) and the same raw material composition were tested under tensile forces in seven directions oriented with 15° increment with respect to the weft direction. Elastic modulus of woven fabrics was determined experimentally in the laboratory. Based on the experimentally obtained values, theoretically calculated elastic modulus for arbitrarily chosen fabric directions was calculated. A good agreement between experimental results and the calculated obtained values of the elastic modulus was shown, so the theoretical equations can be used with high accuracy to calculate the elastic modulus of the fabric in various directions. Therefore, the measurements need to be implemented when the tensile force acting on the fabric only in the warp (90°), weft (0°) and at angle of 45°.

scholarly journals The Study of Process and Characteristics of Woven Fabric from Plant Fibers of Lidah Mertua (Sansevieria trifasciata P.)

2019 ◽  
Vol 7 (2) ◽  
pp. 207-220 ◽  
Author(s):  
Lisa Oktavia Br Napitupulu ◽  
Asri Widyasanti ◽  
Ahmad Thoriq ◽  
Asep Yusuf
Keyword(s):  
Tensile Strength ◽  
Textile Industry ◽  
Natural Fibers ◽  
Woven Fabrics ◽  
Raw Material ◽  
Woven Fabric ◽  
Plant Fibers ◽  
Weft Direction ◽  
A Value ◽  
Descriptive Method

Sansevieria or known as tongue-in-law plant is an ornamental plant that is quite popular in Indonesia. This plant is very easily cultivated, easy to grow in areas with less water and sunlight. This plant contains potential natural fibers used as raw material requirements for textile industry, specifically in fabric making. The aims of this research were to determine the production process consisting and analyzing the characteristics of woven fabrics from the leaves of the tongue-in-law plant. The method of fibers extraction used the mechanical decortication process and making woven fabric is done using ATBM. The research method used is descriptive method. Based on the results of the study, it is known that the woven cloth of tongue-in-law has color characteristics with a value of L* 69.73; a* 1.86; b* 17,38; H 83,88. Besides that, it is known the mechanical characteristics of the tongue-in-law woven fabric, the tensile strength of the fabric, the weft  direction of 46.05 kg and the warp direction of 19.96 kg; weft direction stretch 22% and stretch direction of the warp of 55.20%; weft direction tear strength 19.17% and wrap direction 4.60%; and air penetrating power 116.2 cm3/cm2/s.The value of the tensile strength of the tongue-in-law woven fabric produced in the warp direction does not meet the standards of SNI 08-0056-2006 woven fabric quality requirements for suit.Therefore, woven fabric produced is intended as a craft material.

Interplay of fabric structure and shear thickening fluid impregnation in moderating the impact response of high-performance woven fabrics

2020 ◽  
Vol 54 (28) ◽  
pp. 4387-4395
Author(s):  
Sanchi Arora ◽  
Abhijit Majumdar ◽  
Bhupendra Singh Butola
Keyword(s):  
Beneficial Effect ◽  
Energy Absorption ◽  
Impact Energy ◽  
High Performance ◽  
Research Work ◽  
Impact Resistance ◽  
Woven Fabrics ◽  
Woven Fabric ◽  
Fabric Structure ◽  
The Impact

The beneficial effect of STF impregnation in enhancing the impact resistance of high-performance fabrics has been extensively reported in the literature. However, this research work reports that fabric structure has a decisive role in moderating the effectiveness of STF impregnation in terms of impact energy absorption. Plain woven fabrics having sett varying from 25 × 25 inch−1 to 55 × 55 inch−1 were impregnated with STF at two different padding pressures to obtain different add-ons. The impact energy absorption by STF impregnated loosely woven fabrics was found to be higher than that of their neat counterparts for both levels of add-on, while opposite trend was observed in case of tightly woven fabrics. Further, comparison of tightly woven plain, 2/2 twill, 3/1 twill and 2 × 2 matt fabrics revealed beneficial effect of STF impregnation, except for the plain woven fabric, establishing that there exists a fabric structure-STF impregnation interplay that tunes the impact resistance of woven fabrics.

Effect of weave structure on the slicing cut resistance of woven fabrics

2019 ◽  
Vol 90 (13-14) ◽  
pp. 1477-1494
Author(s):  
Magdi El Messiry ◽  
Shaimaa El-Tarfawy
Keyword(s):  
High Performance ◽  
Normal Load ◽  
Cutting Speed ◽  
Woven Fabrics ◽  
Woven Fabric ◽  
Weft Yarn ◽  
Fabric Structure ◽  
Yarn Count ◽  
Highly Correlated ◽  
Cutting Processes

Cutting processes using blades have found applications in many industries; for example, in garments, fiber–polymer composites, and high-performance fabric forming. In recent decades, the process of cutting the material using a robotic-controlled blade has raised concern about the value of the pressure and the cut force required for a certain type of woven fabric and the estimation of its value before the pressing and cutting process. A simple theoretical relation was established based on the fabric structure and yarn shear stress. The model formulation and experimental results to describe the basic theory of blade cutting fracture for woven fabric of different designs was derived. In this work, the experimental investigation of the effect of the fabric specifications, normal load, and the cutting speed on the cutting force was carried out, which indicates that the value of the specific cutting resistance of the fabric was found to be highly correlated with the fabric structure, warp and weft yarn count, Young’s modulus of the fabric, and fractional cover factors ratio ζ.

scholarly journals Air, moisture and thermal comfort properties of woven fabrics from selected yarns

2018 ◽  
Vol 69 (03) ◽  
pp. 177-182
Author(s):  
ZAHRA QURBAT ◽  
MANGAT ASIF ELAHI ◽  
FRAZ AHMAD ◽  
HUSSAIN SAJID ◽  
ABBAS MUDASSAR ◽  
...  
Keyword(s):  
Water Vapour ◽  
Air Permeability ◽  
Woven Fabrics ◽  
Water Vapour Permeability ◽  
Woven Fabric ◽  
Vapour Permeability ◽  
Weft Direction ◽  
Wetting Time ◽  
Thermal Comfort Properties ◽  
Thermal Absorptivity

Air and moisture transport properties of plain woven fabric made from 20sNec cotton in warp and 20sNec pure yarns of tencel, modal, pro-modal, bamboo, polyester and cotton yarn inweft direction are studied. Major characteristics added for this study include water vapour permeability, air permeability, wettingtime and wicking speed. In comparison of six different samples of variously composed materials in weft direction, the air permeability of tencel was minimum and polyester was maximum, whereas the reverse results were observed for both the samples in case of water vapour permeability. Among the blends with cotton, thermal conductivity of bamboo and thermal absorptivity of polyester was found maximum whereas the minimum thermal resistance was observed for pro modal yarn in weft. Similar pattern was observed in spreading speed and wetting time of the polyester when observed from either side top or bottom. Air and moisture comfort properties of bamboo and pro modal, having nearly similar values are suggested to be used in garments used for golf players

scholarly journals Mathematical Model Predicting the Heat and Power Dissipated in an Electro-Conductive Contact in a Hybrid Woven Fabric

2020 ◽  
Vol 20 (2) ◽  
pp. 133-139
Author(s):  
Carla Hertleer ◽  
Jeroen Meul ◽  
Gilbert De Mey ◽  
Simona Vasile ◽  
Sheilla A. Odhiambo ◽  
...  
Keyword(s):  
Mathematical Model ◽  
Contact Resistance ◽  
Electrical Current ◽  
Woven Fabrics ◽  
Woven Fabric ◽  
Weft Direction ◽  
Flow Through ◽  
Metal Oxide Varistor ◽  
Crossing Point ◽  
Hybrid Fabric

AbstractElectro-conductive (EC) yarns can be woven into a hybrid fabric to enable electrical current to flow through the fabric from one component A to another component B. These hybrid fabrics form the bases of woven e-textiles. However, at the crossing point of an EC yarn in warp and in weft direction, there is a contact resistance and thus generation of heat may occur in this area. Both phenomena are inseparable: if the contact resistance in the EC contact increases, the generated heat will increase as well. Predicting this electrical and thermal behavior of EC contacts in hybrid woven fabrics with stainless steel yarns is possible with a mathematical model based on the behavior of a metal oxide varistor (MOV). This paper will discuss in detail how this can be achieved.

scholarly journals A predictive model of thermal conductivity of plain woven fabrics

2017 ◽  
Vol 21 (4) ◽  
pp. 1627-1632 ◽  
Author(s):  
Jia-Jia Wu ◽  
Hong Tang ◽  
Yu-Xuan Wu
Keyword(s):  
Heat Transfer ◽  
Thermal Conductivity ◽  
Numerical Simulation ◽  
Heat Flux ◽  
Thermal Comfort ◽  
Cell Model ◽  
Woven Fabrics ◽  
Woven Fabric ◽  
Unit Cell Model ◽  
Fabric Structure

This paper proposes an effective method to predict the thermal conductivity of plain woven blended fabric to optimize woven fabric structure, and to evaluate thermal comfort. The unit cell model of fabric is established for numerical simulation of heat transfer through thickness. The thermal conductivity of blended yarns is calculated by a series model. The temperature and heat flux distributions are verified experimentally.

scholarly journals Validation of Design of Regular Carbon Fabric Composite Plate with Woven Fabric using Tensile Loading

2021 ◽  
Vol 13 (4) ◽  
Author(s):  
Sushma D. Thorat ◽  
V. S. Mahajan
Keyword(s):  
Mechanical Properties ◽  
Carbon Fiber ◽  
Tensile Force ◽  
Tensile Loading ◽  
Woven Fabrics ◽  
Woven Fabric ◽  
Light Weight ◽  
Carbon Fabric ◽  
Fabric Composite ◽  
Carbon Fabrics

In many recent years the use of composite materials increases in many fields, for example agricultural uses, where these materials are characterized by good mechanical properties, tenacity and light weight. Among many other materials for the reinforcement of composites, technical fabrics are increasingly being used for the same purpose, especially from carbon fiber, which have good mechanical properties. During tensile stress these fabrics are elongated in the direction of tensile force, and at the same time they contract crosswise in relation to the action of the tensile force. In this Project the tensile properties of regular carbon fabrics and woven fabrics made from carbon fiber yarns were investigated. Static structural analysis of Regular carbon fabrics and woven fabrics base carbon fiber specimen will be done using ACP tool in ANSYS 19 software.

scholarly journals The Effect Of Weave Construction On Tear Strength Of Woven Fabrics

2015 ◽  
Vol 15 (3) ◽  
pp. 207-214 ◽  
Author(s):  
Selin Hanife Eryuruk ◽  
Fatma Kalaoğlu
Keyword(s):  
Woven Fabrics ◽  
Woven Fabric ◽  
Tear Strength ◽  
Plain Weave ◽  
Fabric Structure ◽  
Tearing Strength

Abstract The tear strength of a woven fabric is very important, since it is more closely related to serviceability of the fabric. Tearing strength of the fabrics depend on the mobility of the yarn within the fabric structure. In this study, the tearing strength of four types of fabrics warp rib, weft rib, ripstop and plain weave were analysed, which were produced in different densities and with filament and texturised polyester yarns.

Design and Manufacture of 3D Flat Woven Fabric

2013 ◽  
Vol 333-335 ◽  
pp. 2115-2118 ◽  
Author(s):  
Shu Juan Yan ◽  
Li Hua Lv ◽  
Chun Yan Wei ◽  
Xiao Wang ◽  
Yong Zhu Cui
Keyword(s):  
Structural Design ◽  
Woven Fabrics ◽  
Woven Fabric ◽  
Fabric Structure ◽  
Structural Composite ◽  
Superior Mechanical Properties ◽  
The Cost ◽  
Design And Manufacture ◽  
Application Prospects ◽  
3D Woven Fabrics

In the ordinary loom, the 3D woven fabrics like the orthogonal/connected stitching structure, angle Alliance/interlocked stitching structure by the reasonable transformation, weaving diagram and looming draft, have been woven in this paper. Using ordinary loom weaving fabrics, it would not only save the cost of production, but also has good controllability of woven fabrics. Good structural design and integrity of the 3D woven fabrics, own tight fabric structure, superior mechanical properties, low price, and broad application prospects. The results shows that this design would give a basis for further study on the development perform of 3D textile structural composite materials.

The Effects of Jacquard Woven Fabric Constructional Parameters and Elastane Yarn on Bending Rigidity

2015 ◽  
Vol 10 (2) ◽  
pp. 155892501501000
Author(s):  
Gülcan Süle
Keyword(s):  
Woven Fabrics ◽  
Experimental Results ◽  
Woven Fabric ◽  
Weft Yarn ◽  
Bending Rigidity ◽  
Warp Yarn ◽  
Weft Direction ◽  
Bending Property ◽  
Yarn Count ◽  
Overall Bending

In this research, the bending property of jacquard woven fabrics and the effects of weft density, weft yarn count, weave, and Lycra inclusion in weft yarn on this property were investigated. Viscose filament warp yarn and polyester and polyester/Lycra weft yarns were used for weaving fabrics, and 4/1 and 7/1 satin weaves with the same jacquard design were used as the ground weave. Experimental results show that the bending rigidities of the fabrics in the warp directions increase as the weft density increases and the weft yarn gets thicker. The bending rigidities of the fabrics woven with a 4/1 satin weave in the warp direction are higher compared to the bending rigidities of the fabrics woven with a 7/1 satin weave in the same direction. Similar to the bending rigidities in the warp direction, as the weft density increases and the weft yarn gets thicker, the bending rigidities of the fabrics in the weft directions increase. When the weft yarn includes Lycra, the bending rigidity values of the fabric decrease in the weft direction. Additionally, similar to the bending rigidity in the warp direction, the jacquard woven fabrics with a 4/1 satin weave have a higher bending rigidity in the weft direction compared to the jacquard woven fabrics with a 7/1 satin weave. It was observed that when the weft density increases, the overall bending rigidities of the fabrics increase. Despite fabrics woven with a polyester/Lycra weft yarn having a thicker weft yarn and heavier weight with the same weft density and weave compared to fabrics woven with a polyester weft yarn, the bending rigidity values in the weft direction have a lower overall fabric bending rigidity.

Sign in / Sign up

Export Citation Format

Share Document