Effect of Diffusion Bonding Temperature on Mechanical and Microstructure Characteristics of Cp Titanium and High Strength Aluminium Dissimilar Joints

2015 ◽  
Vol 787 ◽  
pp. 495-499 ◽  
Author(s):  
K. Dheenadayalan ◽  
S. Rajakumar ◽  
V. Balasubramanian
Keyword(s):  
Diffusion Bonding ◽  
Bonding Temperature ◽  
High Strength ◽  
Holding Time ◽  
Diffusion Welding ◽  
Dissimilar Joints ◽  
Bonding Pressure ◽  
Microstructure Characteristics ◽  
Lap Shear ◽  
Commercially Pure

In this investigation, Commercially Pure (Cp) titanium was diffusion bonded to AA7075-T6 aluminium alloy at various temperatures of 450, 475, 500, 525 and 5500C, bonding pressure of 17, MPa and holding time of 40 minutes was applied during the diffusion bonding. The effects of reaction temperature, Bonding time and atmosphere on the diffusion welding characteristics of titanium and aluminum have been studied. The maximum Lap shear strength was found to be 89 MPa for the specimen bonded at the temperature of 525°C, Bonding Pressure 17 MPa and Holding time for 40 min.

Optimization of Ti-6Al-4V/AISI304 diffusion bonding process parameters using RSM and PSO algorithm

2019 ◽  
Vol 15 (6) ◽  
pp. 1037-1052
Author(s):  
A. Arun Negemiya ◽  
S. Rajakumar ◽  
V. Balasubramanian
Keyword(s):  
Process Parameters ◽  
Diffusion Bonding ◽  
Bonding Temperature ◽  
Empirical Relationship ◽  
Pso Algorithm ◽  
Holding Time ◽  
Main Role ◽  
Bonding Pressure ◽  
Content Type ◽  
Lap Shear

Purpose The purpose of this paper is to develop an empirical relationship for predicting the strength of titanium to austenitic stainless steel fabricated by diffusion bonding (DB) process. Process parameters such as bonding pressure, bonding temperature and holding time play the main role in deciding the joint strength. Design/methodology/approach In this study, three-factors, five-level central composite rotatable design was used to conduct the minimum number of experiments involving all the combinations of parameters. Findings An empirical relationship was developed to predict the lap shear strength (LSS) of the joints incorporating DB process parameters. The developed empirical relationship was optimized using particle swarm optimization (PSO). The optimized value discovered through PSO was compared with the response surface methodology (RSM). The joints produced using bonding pressure of 14 MPa, bonding temperature of 900°C and holding time of 70 min exhibited a maximum LSS of 150.51 MPa in comparison with other joints. This was confirmed by constructing response graphs and contour plots. Originality/value Optimizing the DB parameters using RSM and PSO, PSO gives an accurate result when compared with RSM. Also, a sensitivity analysis is carried out to identify the most influencing parameter for the DB process.

scholarly journals Investigation on Processing Maps of Diffusion Bonding Process Parameters for Ti-6Al-4 V/AISI304 Dissimilar Joints

2021 ◽  
Vol 2021 ◽  
pp. 1-9
Author(s):  
A. Arun Negemiya ◽  
A. N. Shankar ◽  
B. Guruprasad ◽  
B. Prakash ◽  
S. Dineshkumar ◽  
...  
Keyword(s):  
Process Parameters ◽  
Diffusion Bonding ◽  
Bonding Temperature ◽  
Dissimilar Materials ◽  
Processing Maps ◽  
Dissimilar Joints ◽  
Bonding Pressure ◽  
Lap Shear ◽  
Titanium Surfaces ◽  
Process Factors

The diffusion bonding (DB) method is used in this investigation to connect high-temperature dissimilar materials. The existence of difficult-to-remove oxide coatings on the titanium surfaces, as well as the arrangement of breakable metallic interlayers and oxide enclosures inside the bond region, provides the most significant challenges during the transition from AISI304 to Ti-6Al-4V alloying. In addition, an effort was made to advance DB processing maps for the operational connection of Ti-6Al-4V to AISI304 alloys to improve their performance. Joints had been created by combining several process factors, such as bonding temperature (T), bonding pressure (P), and holding time (t), to create diverse designs. Based on the findings, database processing maps were created. This set of processing maps may be used as a rough guideline for selecting appropriate DB process parameters for generating virtuous excellent bonds between Ti-6Al-4V and AISI304 alloys. The maximum lap shear strength (LSS) was achieved at 800°C, 15 MPa, and 45 min.

Weldability and machinability of the dissimilar joints of Ti alloy and stainless steel – A review

2021 ◽  
Vol 0 (0) ◽  
Author(s):  
Yan Zhang ◽  
YuanBo Bi ◽  
JianPing Zhou ◽  
DaQian Sun ◽  
HongMei Li
Keyword(s):  
Residual Stress ◽  
Stainless Steel ◽  
Bonding Temperature ◽  
Fusion Welding ◽  
Research Progress ◽  
Diffusion Welding ◽  
Ti Alloy ◽  
Dissimilar Joints ◽  
Advantages And Disadvantages ◽  
Fe Intermetallics

Abstract As two important industrial manufacturing materials, titanium alloys and stainless steel have their own advantages and disadvantages in terms of physical, chemical, and mechanical properties. The field of materials manufacturing has witnessed efforts to develop technical processes that can properly combine these two alloy types, aiming to effectively use their respective advantages. The welding technology for Ti alloy and stainless steel, as a research topic with broad prospects, is comprehensively and deeply analyzed in this review. The current research progress in this field was analyzed from different process perspectives such as fusion welding, brazing, diffusion welding, friction welding, explosive welding and vacuum hot-rolling welding. The results of the review showed that the greatest challenges of fusion welding are low ductility of the material, high residual stress, high cooling rate, and the formation of numerous brittle Ti-Fe intermetallics. By using appropriate intermediate materials between these two materials, the residual stress and brittle intermetallics near the interface of the transition joint can be minimised by solving the thermal expansion mismatch, reducing the bonding temperature and pressure, and suppressing the diffusion of elements such as Ti and Fe.

Diffusion Bonding between AZ31 Magnesium Alloy and 7075 Aluminum Alloy

2014 ◽  
Vol 618 ◽  
pp. 150-153 ◽  
Author(s):  
Zhi Tong Chen ◽  
Fei Lin ◽  
Jie Li ◽  
Fei Wang ◽  
Qing Sen Meng
Keyword(s):  
Shear Strength ◽  
Aluminum Alloy ◽  
Magnesium Alloy ◽  
Diffusion Bonding ◽  
Holding Time ◽  
Az31 Magnesium Alloy ◽  
Diffusion Welding ◽  
7075 Aluminum Alloy ◽  
Micro Hardness ◽  
Welding Temperature

A study on vacuum diffusion bonding between as-extruded AZ31 magnesium alloy and 7075 aluminum alloy was carried out according to atomic diffusion theory. Recrystallization annealing was used for grain refinement of AZ31 magnesium alloy and 7075 aluminum alloy before the diffusion welding. The quality of the bonding joints was checked by shear test, micro-hardness test and microstructure analysis. Experimental results showed that the welding temperature and holding time have a great effect on the joint shear strength. The maximum of shear strength was 38.41MPa under the temperature of 470°C and the holding time of 60min. The result of micro-hardness measurement showed that the micro-hardness of welded joints was maximum. Three kinds of intermetallic compounds, Mg2A13, MgAl and Mgl7Al12, formed at the interfacial transition zone at 470°C.

scholarly journals Prediction of Tensile Strength and Deformation of Diffusion Bonding Joint for Inconel 718 Using Deep Neural Network

Metals ◽  
2020 ◽  
Vol 10 (9) ◽  
pp. 1266 ◽  
Author(s):  
Han Mei ◽  
Lihui Lang ◽  
Xiaoxing Li ◽  
Hasnain Ali Mirza ◽  
Xiaoguang Yang
Keyword(s):  
Neural Network ◽  
Tensile Strength ◽  
Diffusion Bonding ◽  
Inconel 718 ◽  
Deep Neural Network ◽  
Bonding Temperature ◽  
Bonding Pressure ◽  
Bonding Performance ◽  
Strength And Deformation ◽  
Deformation Ratio

Due to the acceptable high-temperature deformation resistance of Inconel 718, its welding parameters such as bonding temperature and pressure are inevitably higher than those of general metals. As a result of the existing punitive processing environment, it is essential to control the deformation of parts while ensuring the bonding performance. In this research, diffusion bonding experiments based on the Taguchi method (TM) are conducted, and the uniaxial tensile strength and deformation ratio of the experimental joints are measured. According to experimental data, a deep neural network (DNN) was trained to characterize the nonlinear relationship between the diffusion bonding process parameters and the diffusion bonding strength and deformation ratio, where the overall correlation coefficient came out to be 0.99913. The double-factors analysis of bonding temperature–bonding pressure based on the prediction results of the DNN shows that the temperature increment of the diffusion bonding of Inconel 718 significantly increases the deformation ratio of the diffusion bonding joints. Therefore, during the multi-objective optimization of the bonding performance and deformation of components, priority should be given to optimizing the bonding pressure and duration only.

Effect of the Bonding Temperature on the Bonding Interface in the Press Bonding of Ti-17 Alloy

2013 ◽  
Vol 773-774 ◽  
pp. 732-740
Author(s):  
Hong Li ◽  
Miao Quan Li ◽  
Hong Bin Liu ◽  
Wei Xin Yu
Keyword(s):  
Plastic Deformation ◽  
Shear Fracture ◽  
Boundary Migration ◽  
Bonding Temperature ◽  
Bonding Interface ◽  
Grain Boundary Migration ◽  
Bonding Pressure ◽  
Lap Shear ◽  
The Press ◽  
Press Bonding

The press bonding experiments of Ti-17 alloy were conducted at the bonding temperatures ranging from 730°C to 880°C, a bonding pressure of 20 MPa and a bonding time of 15 min. The results show that the plastic deformation is a main bonding mechanism in the press bonding of Ti-17 alloy. With an increase in bonding temperature, the plastic deformation enhances and voids in the bonding interface disappear gradually. The grain boundary migration and grain growth spanning the bonding interface start to activate, which is of benefit to obtaining a sound bond. The failure mode of bonding interface changes from a brittle fracture to a ductile fracture. However, a higher bonding temperature will induce grain coarsening which result in strength decreasing. The SEM of lap shear fracture surfaces indicates that a bond with superior strength can be obtained at a bonding temperature of 860°C.

scholarly journals A Low-Temperature Alumina/Copper Diffusion Bonding Process using La-Doped Titanium Interlayers

Coatings ◽  
2018 ◽  
Vol 8 (11) ◽  
pp. 401 ◽  
Author(s):  
Cherng-Yuh Su ◽  
Jia-Liang Huang ◽  
Po-Chun Chen ◽  
Hsin-Jung Yu ◽  
Dai-Liang Ma ◽  
...  
Keyword(s):  
Low Temperature ◽  
Diffusion Bonding ◽  
Bonding Temperature ◽  
Oxygen Affinity ◽  
Temperature Stability ◽  
High Strength ◽  
High Temperature Stability ◽  
Transmission Electron ◽  
Temperature Diffusion ◽  
La Doped

Ceramic-to-metal heterojunctions have been established to improve high-temperature stability for applications in aerospace and harsh environments. In this work, we employed low-temperature diffusion bonding to realize an alumina/Cu heterogeneous joint. Using a thin layer of lanthanum-doped titanium (La-doped Ti) to metallize the alumina surface, we achieved the bonding at a temperature range of 250–350 °C. We produced a uniform, thermally stable, and high-strength alumina/Cu joint after a hot-press process in vacuum. Signals from X-ray diffraction (XRD) suggested the successful diffusion of Ti and La into the alumina substrate, as Ti can easily substitute Al in alumina, and La has a better oxygen affinity than that of Al. The transmission electron microscopy and XRD results also showed the existence of CuxTiyO phases without CuxTiy or LaOx. In addition, the bonding strength of alumina/copper hot-pressed at 250, 300, and 350 °C were 7.5, 9.8 and 15.0 MPa, respectively. The process developed in this study successfully lowered the bonding temperature for the alumina/copper joint.

Efficient Diffusion Bonding between BSCCO Superconducting Multifilamentary Tapes

2008 ◽  
Vol 580-582 ◽  
pp. 295-298
Author(s):  
Gui Sheng Zou ◽  
Yan Ju Wang ◽  
Ai Ping Wu ◽  
Hai Lin Bai ◽  
Nai Jun Hu ◽  
...  
Keyword(s):  
High Temperature ◽  
Diffusion Bonding ◽  
New Technology ◽  
Bonding Temperature ◽  
Interface Bonding ◽  
Bonding Pressure ◽  
Bonding Parameters ◽  
Efficient Diffusion ◽  
Bonding Technology ◽  
Multifilamentary Tapes

To improve the joining efficiency of Bi-Sr-Ca-Cu-O ( BSCCO) superconducting tapes, a new diffusion bonding technology with a direct uniaxial pressing at high temperature was developed to join 61-filament tapes. It was observed that bonding parameters such as bonding pressure and holding time, significantly affected the critical current ratio (CCRo). A peak CCRo value of 89 % for the lap-joined tapes was achieved at 3 MPa for 2 h when bonding temperature was 800 °C. Compared with the conventional diffusion bonding technology, this new technology remarkably shortened the fabrication period and improved the superconductivity of the joints. The bonding interface and microstructures of the joints were evaluated and correlated to the CCRo. An uniaxial pressing at high temperature was beneficial to interface bonding, and there was an optimal pressure value for the CCRo.

A Study on Vacuum Diffusion Bonding of as-Extruded AZ31 Magnesium Alloy

2011 ◽  
Vol 121-126 ◽  
pp. 10-14
Author(s):  
Fei Lin ◽  
Tie Peng Li ◽  
Lu Lu Sun ◽  
Qing Sen Meng
Keyword(s):  
Diffusion Bonding ◽  
Diffusion Theory ◽  
Bonding Temperature ◽  
Holding Time ◽  
Atomic Diffusion ◽  
Hardness Testing ◽  
Joint Shear Strength ◽  
Bonding Quality ◽  
Diffusion Temperature

In this investigation a study on vacuum diffusion bonding of as-extruded AZ31 magnesium alloys was carried out according to atomic diffusion theory. The bonding quality of the joints was checked by microstructure analysis, shear test and micro-hardness testing. The results showed that the diffusion temperature and holding time had a great effect on the the bonding quality of the joints. The maximum of joint shear strength was 76.2MPa with the bonding temperature being 420°C and the holding time reaching 90min.

Mechanical and microstructure property evaluation of diffusion bonding of 5083, 6061 and 7075 aluminium to AZ31 magnesium using Cu interlayer

2021 ◽  
pp. 095440542110144
Author(s):  
Nader Nadermanesh ◽  
Abdolhamid Azizi ◽  
Sahebali Manafi
Keyword(s):  
Mechanical Properties ◽  
Shear Strength ◽  
Diffusion Bonding ◽  
Bonding Temperature ◽  
Effect Of Temperature ◽  
Process Conditions ◽  
Micro Hardness ◽  
Bonding Pressure ◽  
Electron Microscopes ◽  
Cu Interlayer

The diffusion bonding of 7075, 6061 and 5083 aluminium alloys to AZ31B magnesium was investigated using copper interlayer. An optical microscope along with scanning electron microscopes, equipped with an energy dispersive spectrometry/electron probe microanalysis, was utilized to characterize the microstructure of the joint. The mechanical properties of the joint were also assessed by micro-hardness and shear strength tests. The results indicate the high effect of temperature on the bonding results; so that, with a small change in temperature, severe changes were observed in the bonding results. A temperature range of 475°C–485°C and a minimum duration of 30 min with a low bonding pressure of 0.4 MPa were identified as advisable process conditions. The joint evaluation revealed the formation of CuAl2, Cu9Al4 and Al-Mg-Cu ternary phases on the aluminium-copper side, as well as Cu2Mg, CuMg2 and Al-Mg-Cu ternary phases on the magnesium-copper side in the reaction layer. When increasing the bonding temperature and duration, the amount of intermetallic compounds and, as a result, the mechanical properties of the joints changed. The highest shear strength and micro-hardness, related to the bonding performed at 480°C and holding time of 45 min, were 31.03 MPa and 167 HV, respectively.

Sign in / Sign up

Export Citation Format

Share Document