scholarly journals The Application of Taguchi Approach to Optimise the Processing Conditions on Bonnet Polishing of CoCr

2011 ◽  
Vol 496 ◽  
pp. 235-240 ◽  
Author(s):  
Sheng Yue Zeng ◽  
Liam Blunt ◽  
Xiang Qian Jiang
Keyword(s):  
Surface Roughness ◽  
Optimal Condition ◽  
Process Optimization ◽  
Surface Finish ◽  
Taguchi Approach ◽  
Processing Conditions ◽  
Optimal Processing ◽  
Tool Offset ◽  
Cocr Alloy ◽  
Diamond Paste

This paper applied the Taguchi approach to investigate the effects of polishing parameters to obtain the optimal processing conditions for CoCr alloy polishing using a multiaxis CNC controlled corrective polishing machine. The polishing medium used was 1m diamond paste with a Microcloth(polishing cloth). Surface finish parameter Sa was chosen as the criterion for process optimization. The experimental results indicate that the optimal polishing conditions for CoCr alloy polishing is 50 precess angle, 800 rpm head speed, 0.2mm tool offset and 1.5 bar tool pressure. With this optimal condition, a confirmatory experiment was conducted. The surface roughness Sa reduced from an initial 24nm to 7nm and reduction ratio was 70.8% which was very close to the estimated ratio of 64%.

scholarly journals Utilization of Taguchi Approach to Investigate the Effects of Cutting Parameters on Surface Finish of AISI 1020 Steel while turning

2018 ◽  
Vol 8 (01) ◽  
Author(s):  
Mandeep Singh ◽  
Ashwani Kumar
Keyword(s):  
Surface Roughness ◽  
Surface Finish ◽  
Steel Surface ◽  
Cutting Parameters ◽  
Influential Factor ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
Taguchi Approach ◽  
Dry Turning ◽  
Machined Parts

To judge the success of a machining operation, surface finish of the machined parts is one of the important criteria. The value of optimum machining parameters (for better surface finish) can be either decided on the basis of a large number of experimental trails or design of experiments (DoE) can be used to predict the same with significantly lesser number of experimental trails. The aim of this work was to reveal the application of Taguchi method to study the effect of the machining/cutting parameters for surface finish during turning of AISI 1020 steel under different cutting environments. The results revealed that spindle speed was the most influential factor which affected surface roughness in dry turning as well as wet turning. However, depth of cut was second influential factor in dry turning but feed rate was more influential than depth of cut during wet turning Machining, Turning, Steel, Surface finish, Taguchi, Minitab, Anova

scholarly journals On the Relevance of Volumetric Energy Density in the Investigation of Inconel 718 Laser Powder Bed Fusion

Materials ◽  
2020 ◽  
Vol 13 (3) ◽  
pp. 538 ◽  
Author(s):  
Fabrizia Caiazzo ◽  
Vittorio Alfieri ◽  
Giuseppe Casalino
Keyword(s):  
Surface Roughness ◽  
Energy Density ◽  
Process Parameters ◽  
Vickers Hardness ◽  
Powder Bed Fusion ◽  
Processing Conditions ◽  
Laser Powder Bed Fusion ◽  
Powder Bed ◽  
Fractional Density ◽  
Experimental Variation

Laser powder bed fusion (LPBF) can fabricate products with tailored mechanical and surface properties. In fact, surface texture, roughness, pore size, the resulting fractional density, and microhardness highly depend on the processing conditions, which are very difficult to deal with. Therefore, this paper aims at investigating the relevance of the volumetric energy density (VED) that is a concise index of some governing factors with a potential operational use. This paper proves the fact that the observed experimental variation in the surface roughness, number and size of pores, the fractional density, and Vickers hardness can be explained in terms of VED that can help the investigator in dealing with several process parameters at once.

scholarly journals Binary Self-Assembly of Nanocolloidal Arrays using Concurrent and Sequential Spin Coating Techniques

Materials ◽  
2021 ◽  
Vol 14 (2) ◽  
pp. 274
Author(s):  
Shih-Jyun Shen ◽  
Demei Lee ◽  
Yu-Chen Wu ◽  
Shih-Jung Liu
Keyword(s):  
Silicon Substrate ◽  
Self Assembly ◽  
Spin Coating ◽  
Processing Parameters ◽  
The Self ◽  
Silicon Substrates ◽  
Processing Conditions ◽  
Polystyrene Spheres ◽  
Optimal Processing ◽  
Spin Coater

This paper reports the binary colloid assembly of nanospheres using spin coating techniques. Polystyrene spheres with sizes of 900 and 100 nm were assembled on top of silicon substrates utilizing a spin coater. Two different spin coating processes, namely concurrent and sequential coatings, were employed. For the concurrent spin coating, 900 and 100 nm colloidal nanospheres of latex were first mixed and then simultaneously spin coated onto the silicon substrate. On the other hand, the sequential coating process first created a monolayer of a 900 nm nanosphere array on the silicon substrate, followed by the spin coating of another layer of a 100 nm colloidal array on top of the 900 nm array. The influence of the processing parameters, including the type of surfactant, spin speed, and spin time, on the self-assembly of the binary colloidal array were explored. The empirical outcomes show that by employing the optimal processing conditions, binary colloidal arrays can be achieved by both the concurrent and sequential spin coating processes.

Effects of Insert Nose Radius and Processing Cutting Parameter on the Surface Roughness of Aisi 316 Stainless Steel

2010 ◽  
Vol 447-448 ◽  
pp. 51-54
Author(s):  
Mohd Fazuri Abdullah ◽  
Muhammad Ilman Hakimi Chua Abdullah ◽  
Abu Bakar Sulong ◽  
Jaharah A. Ghani
Keyword(s):  
Surface Roughness ◽  
Stainless Steel ◽  
Surface Finish ◽  
Feed Rate ◽  
Cutting Speed ◽  
Chip Thickness ◽  
Cutting Parameters ◽  
Depth Of Cut ◽  
Nose Radius ◽  
Aisi 316

The effects of different cutting parameters, insert nose radius, cutting speed and feed rates on the surface quality of the stainless steel to be use in medical application. Stainless steel AISI 316 had been machined with three different nose radiuses (0.4 mm 0.8 mm, and 1.2mm), three different cutting speeds (100, 130, 170 m/min) and feed rates (0.1, 0.125, 0.16 mm/rev) while depth of cut keep constant at (0.4 mm). It is seen that the insert nose radius, feed rates, and cutting speed have different effect on the surface roughness. The minimum average surface roughness (0.225µm) has been measured using the nose radius insert (1.2 mm) at lowest feed rate (0.1 mm/rev). The highest surface roughness (1.838µm) has been measured with nose radius insert (0.4 mm) at highest feed rate (0.16 mm/rev). The analysis of ANOVA showed the cutting speed is not dominant in processing for the fine surface finish compared with feed rate and nose radius. Conclusion, surface roughness is decreasing with decreasing of the feed rate. High nose radius produce better surface finish than small nose radius because of the maximum uncut chip thickness decreases with increase of nose radius.

Roller Burnishing Method with Active Rotation Tool - Better Surface Finish than Conventional Roller Burnishing

2017 ◽  
Vol 749 ◽  
pp. 9-14 ◽  
Author(s):  
Masato Okada ◽  
Yuki Miyagoshi ◽  
Masaaki Otsu
Keyword(s):  
Surface Roughness ◽  
Aluminum Alloy ◽  
Surface Finish ◽  
Circumferential Direction ◽  
Theoretical Equation ◽  
Sliding Angle ◽  
Roller Burnishing ◽  
Sliding Direction ◽  
Cylindrical Workpiece ◽  
Sectional Profile

This paper proposes a roller burnishing method that controls the sliding direction of the burnishing tool on the surface of cylindrical workpiece. In this study, the sliding direction was set by inclining the axis of the burnishing tool with respect to the axis of the workpiece and by actively rotating the roller of the burnishing tool. The workpiece was a cylindrical aluminum alloy bar, which was rotated in a bench lathe. The burnished surfaces at several sliding angles between 15º and 90º were evaluated. The sliding direction, which is set according to a theoretical equation, was experimentally obtained for every sliding angle in the range of 15-90º with respect to the circumferential direction of the workpiece. The sectional profile was flattened and surface roughness was decreased with increasing sliding angle. As a result, the burnished surfaces obtained in this work were superior to those obtained in an earlier study by the authors, in which the burnishing tool was not actively rotated.

Prediction of Surface Roughness in Compressed Air Jet Assisted High Speed End Milling of Silicon Using Diamond Coated Tools

2012 ◽  
Vol 576 ◽  
pp. 41-45
Author(s):  
A.K.M. Nurul Amin ◽  
M.A. Mahmud ◽  
M.D. Arif
Keyword(s):  
Mathematical Model ◽  
Surface Roughness ◽  
Surface Finish ◽  
High Speed ◽  
End Milling ◽  
Silicon Wafers ◽  
Compressed Air ◽  
Machining Parameters ◽  
High Quality ◽  
Ductile Mode

The majority of semiconductor devices are made up of silicon wafers. Manufacturing of high-quality silicon wafers includes numerous machining processes, including end milling. In order to end mill silicon to a nano-meteric surface finish, it is crucial to determine the effect of machining parameters, which influence the machining transition from brittle to ductile mode. Thus, this paper presents a novel experimental technique to study the effects of machining parameters in high speed end milling of silicon. The application of compressed air, in order to blow away the chips formed, is also investigated. The machining parameters’ ranges which facilitate the transition from brittle to ductile mode cutting as well as enable the attainment of high quality surface finish and integrity are identified. Mathematical model of the response parameter, the average surface roughness (Ra) is subsequently developed using RSM in terms of the machining parameters. The model was determined, by Analysis of Variance (ANOVA), to have a confidence level of 95%. The experimental results show that the developed mathematical model can effectively describe the performance indicators within the controlled limits of the factors that are being considered.

Surface properties of composite resins with and without fluorides for bracket bonding / Propriedades de superfície de resinas compostas com e sem fluoretos para colagem de suportes

2021 ◽  
Vol 7 (7) ◽  
pp. 67267-67276
Author(s):  
Emillyn Jones Greijal Dias Holanda ◽  
José Guilherme Neves ◽  
Milton Santamaria-Jr ◽  
Silvia Amélia Scudeler Vedovello ◽  
Ana Rosa Costa ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Surface Properties ◽  
Color Change ◽  
Composite Resins ◽  
Hardness Tester ◽  
Significant Difference ◽  
Post Test ◽  
Roughness Analysis ◽  
Diamond Paste ◽  
Penetration Time

The aim of this study was to evaluate the surface properties of orthodontic resins with and without fluoride. Forty disks, measuring 2 mm thick by 6 mm in diameter, were made of 4 bracket-bonding composite resins (n=10): Transbond Plus Color Change-3M/Unitek (TPCC); Transbond XT- 3M/Unitek (TXT), Orthocem -FGM (OC); Orthocem UV Trace-FGM (OCUV). The discs were photoactivated for 40 seconds with irradiance of 450 mW/cm2 and manually polished in sequence by silicon carbide sandpapers with 1200 and 2000 grain size and finished with diamond paste and felt disc. The surface microhardness analysis was performed using a Shimadzu Micro Hardness Tester HMV-2,000 (Shimadzu Corporation, Kyoto, Japan) with a load of 50 gF and a 5 second penetration time. Surface roughness readings were taken using a Surf Corder Roughness Meter (SE 1700- Kosaka, Lisboa-Portugal). For data analysis, ANOVA (one-way) was used, followed by Tukey's post-test (?=0.05). The microhardness results showed a difference (p?0.05) in the means of the orthodontic resins between TPCC and TXT with the other groups. After the surface roughness analysis, the averages showed that TPCC resin showed higher roughness compared to OC and OCUV (p?0.05), and there was no statistical difference with TXT. It was concluded that statistically the composite resins with fluoride showed significant difference regarding hardness and roughness.

OPTIMISING CUTTING PARAMETERS FOR HOT TURNING ON EN31 MATERIAL

2021 ◽  
Vol 5 (10) ◽  
Author(s):  
Prof. Hemant k. Baitule ◽  
Satish Rahangdale ◽  
Vaibhav Kamane ◽  
Saurabh Yende
Keyword(s):  
Surface Roughness ◽  
Surface Finish ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Machining Process ◽  
Depth Of Cut ◽  
Multiple Time ◽  
Turning Process ◽  
Workpiece Material ◽  
Hot Turning

In any type of machining process the surface roughness plays an important role. In these the product is judge on the basis of their (surface roughness) surface finish. In machining process there are four main cutting parameter i.e. cutting speed, feed rate, depth of cut, spindle speed. For obtaining good surface finish, we can use the hot turning process. In hot turning process we heat the workpiece material and perform turning process multiple time and obtain the reading. The taguchi method is design to perform an experiment and L18 experiment were performed. The result is analyzed by using the analysis of variance (ANOVA) method. The result Obtain by this method may be useful for many other researchers.

Study on carbon epoxy composite surfaces machined by abrasive water jet machining

2018 ◽  
Vol 53 (20) ◽  
pp. 2909-2924 ◽  
Author(s):  
Ajit Dhanawade ◽  
Shailendra Kumar
Keyword(s):  
Surface Roughness ◽  
Composite Material ◽  
Process Parameters ◽  
Surface Finish ◽  
Epoxy Composite ◽  
Water Jet ◽  
Machining Parameters ◽  
Abrasive Water Jet ◽  
Abrasive Water Jet Machining ◽  
Pull Out

Traditional machining of carbon epoxy composite material is difficult due to excessive tool wear, excessive stresses and heat generation, delamination, high surface waviness, etc. In the present paper, research work involved in the experimental study of abrasive water jet machining of carbon epoxy composite material is described. The aim of present work is to improve surface finish and studying defects in machined samples. Taguchi's orthogonal array approach is used to design experiments. Process parameters namely hydraulic pressure, traverse rate, stand-off distance and abrasive mass flow rate are considered for this study. Analysis of machined surfaces and kerf quality is carried out using scanning electron microscope to evaluate microscopic features. Further, the effect of machining parameters on surface roughness is investigated using analysis of variance approach. It is found that traverse rate and pressure are most significant parameters to control surface roughness. Optimization of process parameters is performed using grey relational analysis. Thereafter, confirmation tests are carried out to verify the improvement in the surface quality with optimum set of process parameters. It is found that surface finish of machined samples is improved by 10.75% with optimum levels of process parameters. Defects like delamination, fiber pull-out and abrasive embedment are also studied using SEM. It is observed that delamination and fiber pull-out are prominent in samples machined at low pressure and high traverse rate.

Sign in / Sign up

Export Citation Format

Share Document