Study of the Mechanical Properties of Concrete with Sisal and Polypropylene Fibers

2015 ◽  
Vol 663 ◽  
pp. 115-123
Author(s):  
Sergio Martínez-Martínez ◽  
Francisco A. Corpas-Iglesias
Keyword(s):  
Compressive Strength ◽  
Natural Fiber ◽  
Fresh Concrete ◽  
Low Cost ◽  
High Strength ◽  
Fiber Reinforced Concrete ◽  
Sisal Fiber ◽  
Partial Replacement ◽  
Capillary Absorption ◽  
Different Types

Fiber concretes have been revolutionizing the market, as well as lower operating costs, structurally act. The total or partial replacement of steel with natural fiber reinforced concrete could be an economical way to provide an alternative method to achieve greater security in concrete structures, as well as a way to use materials that are energy efficient, economic and ecological.Sisal fiber reinforcement is promising for use in composite materials, due to their low cost, low density, high strength and specific modulus, without risk to health, readily available in some countries and renewal.We studied four different dosages of concrete: without fiber, with two different types of polypropylene (PP) fibers and with sisal fiber. Consistency of fresh concrete, bulk density, water absorption, capillary absorption, compressive strength and microstructural properties values of the samples were investigated.Regarding the consistency of fresh concrete, measured by testing Abrams cone, as the results show a substantial difference between the flowability of the concrete without addition of fibers and other dosages with different types of fibers studied. The compressive strength test at 7 and 21 days also shows resistance as early ages performed fiber, while with increasing days of curing, the resistance becomes a reaction product of cement and pozzolanic water have no effect added fiber. Absorption tests and capillary absorption of water, like the above, consistent with the results shown bibliographic polled, the results being higher in both assays for dosages comprised of PP and sisal fibers.

Strength Assesment of Asphaltic Concrete using Bitumen, Natural Fibre and Stone Dust: A Critical Review

2021 ◽  
Vol 9 (VI) ◽  
pp. 3044-3050
Author(s):  
Divesh Sharma
Keyword(s):  
Compressive Strength ◽  
Natural Fibre ◽  
Maximum Strength ◽  
Sisal Fiber ◽  
Partial Replacement ◽  
Fine Aggregate ◽  
Asphaltic Concrete ◽  
Stone Dust ◽  
Strength And Durability ◽  
Research Studies

In this review article, the usage of bitumen, sisal fiber and the sisal fiber for improving the strength parameters of concrete is discussed in detail. Numerous research studies related to the usage of bitumen, sisal fiber and stone dust are studied in detail to determine the results and outcome out of it. Previous research works showed that all, these materials were enhancing the strength and durability aspects of the concrete and depending upon the research studies certain outcomes has been drawn which are as follows. The studies related to the usage of the bitumen or asphalt in concrete so as to produce bituminous concrete or asphaltic concrete, the previous research works conclude that the maximum strength was attained at 5 percent usage of the bitumen and after further usage the general compressive strength of the concrete starts declining. The previous studies related to the usage of the sisal fiber showed that with the usage of the sisal fiber in the concrete, the strength aspects of concrete were improving and the maximum strength was obtained at 1.5 percent usage of the sisal fiber and after his the strength starts declining. Further the studies related to the usage of the stone dust showed that with the usage of stone dust as partial replacement of the natural fine aggregate the compressive strength of the concrete was improving and it was conclude that with the increase in the percentage of the stone dust, the compressive strength of the concrete was increasing.

scholarly journals Kajian Karakteristik Beton Memadat Sendiri yang Menggunakan Serat Ijuk (Hal. 54-65)

2018 ◽  
Vol 4 (4) ◽  
pp. 54
Author(s):  
Iis Nurjamilah ◽  
Abinhot Sihotang
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Flexural Strength ◽  
Coarse Aggregate ◽  
Fresh Concrete ◽  
High Strength ◽  
Self Compacting Concrete ◽  
Palm Fiber ◽  
Fiber Concrete ◽  
Dilute Mixture

ABSTRAKKajian karakteristik beton memadat sendiri yang menggunakan serat ijuk merupakan sebuah kajian yang dilakukan untuk mengetahui pengaruh penambahan serat ijuk terhadap karakteristik beton memadat sendiri (SCC). Beton memadat sendiri yang menggunakan serat ijuk (PFSCC) didesain memiliki campuran yang encer, bermutu tinggi (= 40 MPa) dan memiliki persentase kekuatan lentur yang lebih baik. PFSCC  didapatkan dari hasil pencampuran antara semen sebanyak 85%, fly ash 15%, superplastizicer 1,5%, serat ijuk 0%, 0,5%; 1%; 1,5%; 2% dan 3% dari berat binder (semen + fly ash), kadar air 190 kg/m3, agregat kasar 552,47 kg/m3 dan pasir 1.063 kg/m3. Semakin banyak persentase penambahan serat ijuk ke dalam campuran berdampak terhadap menurunnya workability beton segar. Penambahan serat ijuk yang paling baik adalah sebanyak 1%, penambahan tersebut dapat meningkatkan kekuatan tekan beton sebesar 13% dan lentur sebesar 1,8%.Kata kunci: beton memadat sendiri (SCC), beton berserat, beton memadat sendiri yang menggunakan serat ijuk (PFSCC), serat ijuk ABSTRACTThe study of characteristics self compacting concrete using palm fibers is a study conducted to determine the effect of adding palm fibers to characteristics of self compacting concrete (SCC). palm fibers self compacting concrete (PFSCC) is designed to have a dilute mixture, high strength (= 40 MPa), and have better precentage flexural strength. PFSCC was obtained from mixing of 85% cement, 15% fly ash, 1.5% superplastizicer, 0%, 0.5%, 1%, 1.5%, 2% and 3% palm fibers from the weight of binder  (cement + fly ash), water content 190 kg/m3, coarse aggregate 552.47 kg/m3 and sand 1,063 kg/m3. The more persentage palm fibers content added to the mixture makes workability of fresh concrete decreases. The best addition of palm fiber is 1%, this addition can increases the compressive strength 13% and flexural strength 1.8%.Keywords: self compacting concrete (SCC), fiber concrete, Palm fiber self compacting concrete (PFSCC), palm fiber

Performance of Stabilized Earth with Wheat Straw and Slag

MRS Advances ◽  
2020 ◽  
Vol 5 (25) ◽  
pp. 1285-1294 ◽  
Author(s):  
W Benhaoua ◽  
K. Grine ◽  
S. Kenai
Keyword(s):  
Thermal Conductivity ◽  
Compressive Strength ◽  
Low Cost ◽  
Construction Material ◽  
Soil Samples ◽  
Capillary Absorption ◽  
Wetting And Drying ◽  
Environment Friendly ◽  
Granulated Blast Furnace Slag ◽  
Local Soil

ABSTRACTStabilized earth is a very ancient material that has been used in many countries as a low cost, environment friendly construction material. However, its durability under humid environments is low. Stabilization using cement, lime and natural fibres could enhance its durability and lowers the risk of cracking. This paper presents an experimental investigation into the performance of stabilised local soil by either, cement mixed with a proportion of granulated blast furnace slag (GBFS) /or straw naturel fibres. Unconfined compressive strength (UCS), shrinkage, wetting and drying, capillary absorption and thermal conductivity tests were performed on both untreated soil samples and stabilised soil samples. The results show that stabilising the soil with cement and GBFS increased both compressive strength, durability, thermal conductivity and decreased the capillary absorption and the shrinkage. The addition of natural wheat fibres increased the capillary absorption but leads to a decrease in the thermal conductivity and to a further reduction in the shrinkage and hence a better insulating less prone to cracking material.

Assessment of mechanical and fire resistance for hybrid nano-clay and steel fibres concrete at different curing ages

2019 ◽  
Vol 11 (2) ◽  
pp. 189-203 ◽  
Author(s):  
Ola Bakr Shalby ◽  
Hala Mohamed Elkady ◽  
Elsayed Abdel Raouf Nasr ◽  
Mohamed Kohail
Keyword(s):  
Compressive Strength ◽  
Residual Strength ◽  
Low Cost ◽  
Partial Replacement ◽  
Fire Exposure ◽  
Content Type ◽  
Steel Fibres ◽  
Concrete Properties ◽  
Nano Clay ◽  
Concrete Mix

Purpose Nano-Clay (NC) is reported as a candidate partial replacement for cement, due to its abundance and relatively low cost - beside reported promotion of different concrete properties. On the other hand, Steel Fibres (SF) has proven to have a positive effect on post fire exposure residual strength of concrete. This paper aims to present the outcomes of a comprehensive research program assessing a hybrid mix between NC and SF in concrete mixtures (NCSF-CRETE). Design/methodology/approach Physical chemical and physical characterization of NC is performed using different tools as XRF spectrometer, and TEM micrograph. Fresh concrete properties of NSCF-CRETE as slump and air content are investigated. Enhancement in permeability using NSCF is verified by comparing its resistance to the penetration of chlorides resistance with regular concrete mix. Besides, the proposed NCSF-CRETE compressive strength is evaluated compared to mixes with NC and SF each used separately at different curing ages. Besides, NSCF and compared mixes are exposed to an indirect fire testing program – two hours exposure – for: 300, 450 and 600°C. Degradation in compressive strength was investigated after exposure to different temperatures and percentage of residual strength is reported. Findings Results indicated an improved performance of NCSF -CRETE of about 40% compared to regular concrete in compressive strength at normal conditions. This improvement extended to its behavior when subjected to indirect fire exposure NSCF also maintained 40% more strength than the residual in regular concrete mix – which suffered severe damage – after 2 h exposure to 600°C. Originality/value Using NCSF-Crete allows retrofitting the structure after exposure to such drastic conditions.

Compressive Properties of High Strength Steel Fiber Reinforced Concrete with Different Fiber Volume Fractions

2013 ◽  
Vol 372 ◽  
pp. 215-218 ◽  
Author(s):  
Hye Ran Kim ◽  
Seung Ju Han ◽  
Hyun Do Yun
Keyword(s):  
Compressive Strength ◽  
Reinforced Concrete ◽  
High Strength Steel ◽  
Steel Fiber ◽  
High Strength ◽  
Fiber Reinforced Concrete ◽  
Experimental Results ◽  
Steel Fiber Reinforced Concrete ◽  
Fiber Volume ◽  
Volume Fractions

This paper describes the experimental results of 70 MPa high strength steel fiber reinforced concrete (SFRC) with different steel fiber volume fractions in compression. The effect of steel fiber on fresh properties, compressive strength, toughness index, cracking procedure of high strength steel fiber concrete is also investigated. The steel fibers were added as the volume fractions of 0%, 0.5%, 1.0%, 1.5% and 2.0%. The cylindrical specimens with Φ100 x 200 for compressive tests were manufactured in accordance with ASTM C 39[. The experimental results showed that the slump of fresh SFRC was inversely proportional to the fiber volume fraction added to high strength concrete. As the addition of steel fiber increased, compressive strength of SFRC decreased. Inclusion of steel fiber improves compressive toughness of high strength SFRC.

scholarly journals The Effect of Various Polynaphthalene Sulfonate Based Superplasticizers on the Workability of Reactive Powder Concrete

2021 ◽  
Vol 2 (1) ◽  
Author(s):  
Anthony Torres ◽  
Federico Aguayo ◽  
Srinivas Allena ◽  
Michael Ellis
Keyword(s):  
Compressive Strength ◽  
Fresh Concrete ◽  
High Strength ◽  
Reactive Powder Concrete ◽  
Chemical Admixture ◽  
Lower Viscosity ◽  
Reactive Powder ◽  
The Impact ◽  
Polycarboxylate Ether ◽  
High Range

A superplasticizer is a type of chemical admixture used to alter the workability (viscosity) of fresh concrete. The workability of fresh concrete is often of particular importance when the water-to-cement (w/c) ratio is low and a particular workability is desired. Reactive Powder Concrete (RPC) is a high-strength concrete formulated to provide compressive strengths exceeding 130MPa and made of primarily powders. RPC materials typically have a very low w/c, which requires the use of a chemical admixture in order to make the material workable for placing, handling and consolidating. Superplasticizer are commonly used for this purpose. Superplasticizers are developed from different formulations, the most common being Polynaphthalene Sulfonate (PNS), Polymelamine Sulfonate (PMS) and Polycarboxylate Ether (PCE). This study investigates the impact of various PNS based superplasticizers on the compressive strength and rheological performance of a RPC mixture. Six different types of PNS based superplasticizers were used; three of various compositional strengths (high, medium, low range) from a local provider, and three of the same compositional strengths (high, medium, low) from a leading manufacturer. Specific properties assessed were the superplasticizers viscosity, concrete workability through the mortar-spread test, concrete rheology, and 7, 14, and 28 day RPC compressive strengths. Two mixtures were produced with two w/cm (0.20 and 0.15), which would subsequently increase the amount of superplasticizer needed, from 34.7L/m3 to 44.5L/m3. The results show that the name brand high range composition produced the overall highest spread, lowest viscosity, and a highest compressive strength at all ages tested. However, the local provider outperformed the name brand in the mid and low range compositions. Additionally, the rheology test also demonstrated that the name brand high range, and RPC produced with the name brand high range, had a lower viscosity at all angular speeds than the others tested.

scholarly journals Tests on workability and strength of high strength-flowable concrete containing PET waste fiber

2020 ◽  
Vol 7 (3) ◽  
pp. 115-139
Author(s):  
Sarkawt Karim ◽  
◽  
Azad Mohammed ◽  
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Fiber Length ◽  
High Strength ◽  
Fiber Reinforced Concrete ◽  
Time Increase ◽  
Fiber Volume ◽  
Split Tensile Strength ◽  
Pet Waste ◽  
Strength Tests

This study describes two workability tests, compressive strength and tensile strength tests of high strength flowable concrete containing plastic fiber prepared from polyethylene terephthalate (PET) waste bottles. For the high fluidity mix Vebe time and V-funnel time tests were carried out. Results show that there is a Vebe time increase with PET fiber addition to concrete being increased with increasing fiber volume and fiber length. V-funnel time was found to reduce when up to 0.75% fiber volume is added to concrete, followed by an increase for larger fiber volumes. When fiber length is increase, there is more time increase, but in general, V-funnel time increase was lower than that of Vebe time, indicating a different influence of PET fiber on the compatibility and flowability. The measured V-funnel time for all mixes was found to conform to the limits of European specifications on the flowability of self compacting concrete. Small descending in compressive strength was recorded for RPET fiber reinforced concrete that reached 15.74 % for 1.5 percent fiber content with 10 mm fiber length. Attractive results was recorded in split tensile strength of RPET fibrous samples which resulted in improvement up to 63.3 % for 1.5 percent of 40 mm fiber length content.

scholarly journals Strength Determination of High Strength Concrete Blended with Copper Slag and Fly Ash

2021 ◽  
Vol 9 (VII) ◽  
pp. 1198-1203
Author(s):  
Jamshed Alam
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
High Strength Concrete ◽  
Free Water ◽  
High Strength ◽  
Copper Slag ◽  
Partial Replacement ◽  
Fine Aggregate ◽  
Strength Concrete ◽  
Free Water Content

An experimental analysis was conducted to study the effects of using copper slag as a fine aggregate (FA) and the effect of fly ash as partial replacement of cement on the properties high strength concrete. In this analysis total ten concrete mixtures were prepared, out of which five mixes containing different proportions of copper slag ranging from 0% (for the control mix) to 75% were prepared and remaining five mixes containing fly ash as partial replacement of cement ranging from 6% to 30% (all mixes contains 50% copper slag as sand replacements). Concrete matrix were tested for compressive strength, tensile strength and flexural strength tests. Addition of copper slag as sand replacement up to 50% yielded comparable strength with that of the control matrix. However, further additions of copper slag, caused reduction in strength due to an increment of the free water content in the mix. Concrete mix with 75% copper slag replacement gave the lowest compressive strength value of approximately 80 MPa at 28 days curing period, which is almost 4% more than the strength of the control mix. For this concrete containing 50% copper slag, fly ash is introduced in the concrete to achieve the better compressive, split and flexural strengths. It was also observed that, introduction of the fly ash gave better results than concrete containing 50% copper slag. When concrete prepared with 18 % of fly ash, the strength has increased approximately 4%, and strength decreased with further replacements of the cement with fly ash. Hence, it is suggested that 50% of copper slag can be used as replacement of sand and 18% fly ash can be used as replacement of cement in order to obtain high strength concrete.

scholarly journals Performance of sustainable self-compacting fiber reinforced concrete with substitution of marble waste (MW) and coconut fibers (CFs)

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Jawad Ahmad ◽  
Fahid Aslam ◽  
Rebeca Martinez-Garcia ◽  
Mohamed Hechmi El Ouni ◽  
Khalid Mohamed Khedher
Keyword(s):  
Experimental Investigation ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Reinforced Concrete ◽  
High Strength ◽  
Fiber Reinforced Concrete ◽  
Self Compacting Concrete ◽  
Pozzolanic Materials ◽  
Passing Ability ◽  
Marble Waste

AbstractSelf compacting concrete (SCC) is special type of concrete which is highly flowable and non-segregated and by its own mass, spreads into the formwork without any external vibrators, even in the presence of thick reinforcement. But SSC is also brittle nature like conventional concrete, which results in abrupt failure without giving any deformation (warning), which is undesirable for any structural member. Thus, self-compacting concrete (SCC) needs some of tensile reinforcement to enhance tensile strength and prevent the unsuitable abrupt failure. But fiber increased tensile strength of concrete more effectively than compressive strength. Hence, it is essential to add pozzolanic materials into fiber reinforced concrete to achieve high strength, durable and ductile concrete. This study is conducted to assess the performance of SCC with substitutions of marble waste (MW) and coconut fiber (CFs) into SCC. MW utilized as cementitious (pozzolanic) materials in percentage of 5.0 to 30% in increment of 5.0% by weight of binder and concrete is reinforced with CFs in proportion of 0.5 to 3.0% in increment of 0.5% by weight of binder. Rheological characteristics were measured through its filling and passing ability by using Slump flow, Slump T50, L-Box, and V-funnel tests while mechanical characteristics were measured through compressive strength, split tensile strength, flexure strength and bond strength (pull out) tests. Experimental investigation show that MW and CFs decrease the passing ability and filling ability of SCC. Additionally, Experimental investigation show that MW up to 20% and CFs addition 2.0% by weight of binder tend to increase the mechanical performance of SCC. Furthermore, statistical analysis (RSM) was used to optimize the combined dose of MW and CFs into SCC to obtain high strength self-compacting concrete.

scholarly journals Development of An Environmental-Friendly Durable Concrete

2021 ◽  
Author(s):  
DEEP TRIPATHI ◽  
Rakesh Kumar ◽  
Pradeep Kumar Mehta
Keyword(s):  
Compressive Strength ◽  
Structural Changes ◽  
Fresh Concrete ◽  
Tap Water ◽  
Partial Replacement ◽  
Natural Sand ◽  
Environment Friendly ◽  
Manufactured Sand ◽  
Slump Flow ◽  
Micro Level

Abstract In this experimental study on Self Compacting Concrete (SCC), the Manufactured sand (M-sand) and Fly ash (FA) were utilised for partial replacement of Natural sand (N-sand) and Ordinary Portland Cement (OPC), respectively. N-sand was partially replaced by M-sand at various percentage levels, after the dose of FA in the mix was optimized. In terms of compressive strength, the optimum replacement level of OPC by FA was 20%, while for replacement of N-sand by M-sand it was 50%. Two types of mixes were made to compare the macro and micro level properties of SCC, i.e., SCC-I (100%OPC+100%N-sand), and SCC-II (80%OPC+20%FA+50%N-sand+50%M-sand). The characteristics of fresh concrete mixes were determined using Slump flow, T50 time, V-funnel, L-box, U-box, and J-ring tests. After 28 days of curing in tap water, both type of specimens were exposed in solution of Ammonium Sulphate [(NH4)2SO4] containing Sulphate salt concentration of 2.0g/l for 360 days to test their durability. Loss in compressive strength, weight change, sorptivity, and micro-structural changes (XRD, SEM, and EDS) all were evaluated up to 360 days. It was found that the use of FA and M-sand in concrete makes it more environment friendly and durable, as well as having higher performance in a sulphate environment.

Sign in / Sign up

Export Citation Format

Share Document