Research of the Influence of the Physical and Mechanical Properties of the Workpiece Material on the Temperature Field of the Turning Process

2021 ◽  
Vol 1037 ◽  
pp. 300-308
Author(s):  
Alexander N. Unyanin ◽  
Pavel R. Finageev
Keyword(s):  
Cutting Force ◽  
Yield Stress ◽  
Physical And Mechanical Properties ◽  
Tangential Component ◽  
Machining Process ◽  
Regression Equations ◽  
Workpiece Material ◽  
Friction Forces ◽  
The Face ◽  
Contact Surfaces

To predict the parameters of the quality of the processed parts and the period of durability of the cutting tool, mathematical models are needed that will allow us to calculate not only the mathematical expectation of the parameters of the machining process, but also the dispersion of these parameters. The working capacity of the tool and the quality parameters of the parts depend significantly on the temperature on the contact surfaces of the tool, as well as on the surface of the workpiece. Mathematical dependences for calculating the components of the total heat generation capacity during turning are given. It is assumed that the yield stress, which determines the cutting and friction forces on the contact surfaces of the cutter, workpiece and chip, depends on the temperature in the area of plastic deformation. The heat transfer at the boundaries of objects in contact with the process fluid or air is given in the form of the Newton-Richman law. The equations of thermal conductivity of contacting objects were solved together with the general boundary conditions in the contact zone, using the finite element method. The results of numerical simulation of the main component of the cutting force and temperatures in the contact zones of the face of the cutter with the chips and the fiank surface with the workpiece, depending on the yield strength of the workpiece material, are presented. The values of fluctuations in the cutting force and contact temperatures depending on the spread of the yield stress of the workpiece material during turning of workpieces made of 45 and 12X18H10T steels are determined. Based on the results of numerical modeling, regression equations are obtained for calculating the tangential component of the cutting force, the temperatures on the face and flank surfaces of the cutter, and the temperature on the surface of the workpiece.

Study on Technology Parameters for Coated Carbide Cutting Tools

2014 ◽  
Vol 556-562 ◽  
pp. 498-501
Author(s):  
Xiao Jing Li ◽  
Yan Hui Hu ◽  
Di Wang ◽  
Dong Man Yu
Keyword(s):  
Hard Alloy ◽  
Cutting Force ◽  
Metal Cutting ◽  
Cutting Tools ◽  
High Hardness ◽  
Machining Process ◽  
High Wear Resistance ◽  
Workpiece Material ◽  
Ticn Coating ◽  
Coated Carbide

Metal cutting processing is the most fundamental, most widely and the most important processing in industrial production. Because the development of mechanical manufacturing level plays a very important role in the coating technology material machining process. A coated carbide cutting tool with its high hardness and high wear resistance, good chemical stability and extensive compatibility characteristics, is widely applied in the metal cutting processing field. The author mainly studies the cutting force contrast between coated carbide cutting tools and not coated ones. Cutting tests have testified that if PVD technology applied on cutting, the cutting force of hard alloy cutter will alter with the change of feeds (f), depth of cutting (ap) and cutting velocity (v). The experiment suggests that the size of three-way cutting force of either the brand ZP25 hard alloy cutter or the carbide cutter by employing matrix ZP25 hard alloy cutter to respectively using PVD technology coat TiN or TiCN coating is successively FZP25>FTiCN>FTiN. The main reason for this is that the difference of frictional factor of the three kinds of cutter material and the workpiece material.

Simulation Analysis of RuT450 Drilling Force Based on LS-DYNA Gun Drilling

2018 ◽  
Vol 764 ◽  
pp. 271-278 ◽  
Author(s):  
H. Guo ◽  
W. Yang ◽  
L. Liu ◽  
X.K. Yang ◽  
Y.G. Wang ◽  
...  
Keyword(s):  
Cutting Force ◽  
Feed Rate ◽  
Equivalent Stress ◽  
Cutting Speed ◽  
Machining Process ◽  
Cutting Fluid ◽  
Drilling Process ◽  
Drilling Force ◽  
Workpiece Material ◽  
The Impact

Cutting force is one of the most important parameters in the machining process, it significantly influenced machining precision of the workpiece, power consumed in the machining process, wear of the cutting tools and so on. There are many factors that affect the cutting force, such as the performance of the workpiece material, cutting speed, usage of the cutting fluid, etc. Single factor variable method was used in this paper, RuT450 was used as workpiece, welded cemented carbide gun drill was used as cutting force and LS-DYNA was used as simulation platform to established the cutting simulation model to analyzed the impact of the cutting speed and feed rate to the drilling force. Simulation results show that, at the low speed drilling stage, drilling force increases with the increase of the feed rate and decreases with the increase of the rotation feed, from the stress cloud it could be seen that the equivalent stress near the drill tip reached the maximum in the drilling process.

Structure and properties of compact articles from high-alloyed iron powder with adding of boron nitride

2020 ◽  
pp. 39-48
Author(s):  
B. O. Bolshakov ◽  
◽  
R. F. Galiakbarov ◽  
A. M. Smyslov ◽  
◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Boron Nitride ◽  
Grain Boundary ◽  
Bending Strength ◽  
Physical And Mechanical Properties ◽  
Operating Conditions ◽  
Structure And Properties ◽  
Steam Turbines ◽  
Friction Forces ◽  
Wide Range

The results of the research of structure and properties of a composite compact from 13 Cr – 2 Мо and BN powders depending on the concentration of boron nitride are provided. It is shown that adding boron nitride in an amount of more than 2% by weight of the charge mixture leads to the formation of extended grain boundary porosity and finely dispersed BN layers in the structure, which provides a high level of wearing properties of the material. The effect of boron nitride concentration on physical and mechanical properties is determined. It was found that the introduction of a small amount of BN (up to 2 % by weight) into the compacts leads to an increase in plasticity, bending strength, and toughness by reducing the friction forces between the metal powder particles during pressing and a more complete grain boundary diffusion process during sintering. The formation of a regulated structure-phase composition of powder compacts of 13 Cr – 2 Mо – BN when the content of boron nitride changes in them allows us to provide the specified physical and mechanical properties in a wide range. The obtained results of studies of the physical and mechanical characteristics of the developed material allow us to reasonably choose the necessary composition of the powder compact for sealing structures of the flow part of steam turbines, depending on their operating conditions.

scholarly journals Serrated Chips Formation in Micro Orthogonal Cutting of Ti6Al4V Alloys with Equiaxial and Martensitic Microstructures

Micromachines ◽  
2019 ◽  
Vol 10 (3) ◽  
pp. 197 ◽  
Author(s):  
ZeJia Zhao ◽  
Suet To ◽  
ZhuoXuan Zhuang
Keyword(s):  
Cutting Force ◽  
Unit Length ◽  
Orthogonal Cutting ◽  
Machining Process ◽  
Orthogonal Machining ◽  
Large Yield ◽  
Power Spectral ◽  
Straight Line ◽  
Serrated Chips ◽  
Electropulsing Treatment

The formation of serrated chips is an important feature during machining of difficult-to-cut materials, such as titanium alloy, nickel based alloy, and some steels. In this study, Ti6Al4V alloys with equiaxial and acicular martensitic microstructures were adopted to analyze the effects of material structures on the formation of serrated chips in straight line micro orthogonal machining. The martensitic alloy was obtained using highly efficient electropulsing treatment (EPT) followed by water quenching. The results showed that serrated chips could be formed on both Ti6Al4V alloys, however the chip features varied with material microstructures. The number of chip segments per unit length of the alloy with martensite was more than that of the equiaxial alloy due to poor ductility. Besides, the average cutting and thrust forces were about 8.41 and 4.53 N, respectively, for the equiaxed Ti6Al4V alloys, which were consistently lower than those with a martensitic structure. The high cutting force of martensitic alloy is because of the large yield stress required to overcome plastic deformation, and this force is also significantly affected by the orientations of the martensite. Power spectral density (PSD) analyses indicated that the characteristic frequency of cutting force variation of the equiaxed alloy ranged from 100 to 200 Hz, while it ranged from 200 to 400 Hz for workpieces with martensites, which was supposedly due to the formation of serrated chips during the machining process.

scholarly journals Modeling of Cutting Force in the Turning of AISI 4340 Using Gaussian Process Regression Algorithm

2021 ◽  
Vol 11 (9) ◽  
pp. 4055
Author(s):  
Mahdi S. Alajmi ◽  
Abdullah M. Almeshal
Keyword(s):  
Gaussian Process ◽  
Cutting Force ◽  
Predictive Accuracy ◽  
Gaussian Process Regression ◽  
Machining Process ◽  
Support Vector ◽  
Process Data ◽  
Cutting Force Prediction ◽  
Artificial Neural Network Ann ◽  
Aisi 4340

Machining process data can be utilized to predict cutting force and optimize process parameters. Cutting force is an essential parameter that has a significant impact on the metal turning process. In this study, a cutting force prediction model for turning AISI 4340 alloy steel was developed using Gaussian process regression (GPR), support vector machines (SVM), and artificial neural network (ANN) methods. The GPR simulations demonstrated a reliable prediction of surface roughness for the dry turning method with R2 = 0.9843, MAPE = 5.12%, and RMSE = 1.86%. Performance comparisons between GPR, SVM, and ANN show that GPR is an effective method that can ensure high predictive accuracy of the cutting force in the turning of AISI 4340.

Optimization of turn-milling process in roughing and finishing regimes: Trade-off between productivity, cutting force and surface integrity

2021 ◽  
pp. 095440892199851
Author(s):  
Ebrahim Hosseini ◽  
Shafiqur Rehman ◽  
Ashkan Alimoradi
Keyword(s):  
Cutting Force ◽  
Desirability Function ◽  
Milling Process ◽  
Machining Process ◽  
Hybrid Machining ◽  
Trade Off ◽  
Hybrid Machining Process ◽  
Process Factors ◽  
Turn Milling ◽  
Selection Of

Turn-milling is a hybrid machining process which used benefits of interrupted cutting for proceeding of round bars. However, number of controllable parameters in the hybrid process is numerous that makes optimizing the process complicated. In the present study, an optimization work has been proposed to investigate the trade-off between production rate and cutting force in roughing regime as well surface roughness and tensile residual stress in finishing regime. Number of 43 experiments based on response surface methodology was designed and carried out to gather required data for development of quadratic empirical models. Then, the adequacy and importance of process factors were analyzed using analysis of variances. Finally, desirability function was used to optimize the process in rough and finish machining regimes. The obtained results showed that selection of eccentricity and cutter speed at their maximum working range can effectively enhance the quality characteristics in both the roughing and finishing regimes.

Surface Roughness and Cutting Force Components Evaluation in Hard Turning by Differently Shaped Cutting Tools

2016 ◽  
Vol 862 ◽  
pp. 26-32 ◽  
Author(s):  
Michaela Samardžiová
Keyword(s):  
Surface Roughness ◽  
Cutting Force ◽  
Hard Turning ◽  
Cutting Tool ◽  
Single Point ◽  
Machining Process ◽  
Tool Geometry ◽  
Machined Surface ◽  
Cutting Force Components ◽  
Force Components

There is a difference in machining by the cutting tool with defined geometry and undefined geometry. That is one of the reasons of implementation of hard turning into the machining process. In current manufacturing processes is hard turning many times used as a fine finish operation. It has many advantages – machining by single point cutting tool, high productivity, flexibility, ability to produce parts with complex shapes at one clamping. Very important is to solve machined surface quality. There is a possibility to use wiper geometry in hard turning process to achieve 3 – 4 times lower surface roughness values. Cutting parameters influence cutting process as well as cutting tool geometry. It is necessary to take into consideration cutting force components as well. Issue of the use of wiper geometry has been still insufficiently researched.

Simulation of Machining of Incoloy 907 Based on Thermodynamical Constitutive Equation

2013 ◽  
Vol 631-632 ◽  
pp. 681-685
Author(s):  
Fang Shao ◽  
Fa Qing Li ◽  
Hai Ying Zhang ◽  
Xuan Gao
Keyword(s):  
Cutting Force ◽  
Cutting Temperature ◽  
Tool Material ◽  
High Reactivity ◽  
Good Prediction ◽  
Workpiece Material ◽  
Element Analysis ◽  
Good Prediction Accuracy ◽  
Experimental Cutting ◽  
Cutting Tool Materials

Aero-engine alloys (also as known as superalloys)are known as difficult-to-machine materials, especially at higher cutting speeds, due to their several inherent properties such as low thermal conductivity and their high reactivity with cutting tool materials. In this paper a finite element analysis (FEA) of machining for Incoloy907 is presented. In particular, the thermodynamical constitutitve equation(T-C-E) in FEA is applied for both workpiece material and tool material. Cutting temperature and cutting force are predicted. The comparison between the predicted and experimental cutting temperature and cutting force are presented and discussed. The results indicated that a good prediction accuracy of both principal cutting temperature and cutting force can be achieved by the method of FEA with thermodynamical constitutitve equation.

scholarly journals The Comparative Study on Cutting Performance of Different-Structure Milling Cutters in Machining CFRP

2018 ◽  
Vol 8 (8) ◽  
pp. 1353
Author(s):  
Tao Chen ◽  
Fei Gao ◽  
Suyan Li ◽  
Xianli Liu
Keyword(s):  
Carbon Fiber ◽  
Cutting Force ◽  
Surface Quality ◽  
Cutting Edge ◽  
Cutting Performance ◽  
Machining Process ◽  
Carbon Fiber Composites ◽  
Machined Surface ◽  
Milling Cutter ◽  
Machined Surface Quality

Carbon fiber reinforced plastic (CFRP) is typically hard to process, because it is easy for it to generate processing damage such as burrs, tears, delamination, and so on in the machining process. Consequently, this restricts its wide spread application. This paper conducted a comparative experiment on the cutting performance of the two different-structure milling cutters, with a helical staggered edge and a rhombic edge, in milling carbon fiber composites; analyzed the wear morphologies of the two cutting tools; and thus acquired the effect of the tool structure on the machined surface quality and cutting force. The results indicated that in the whole cutting, the rhombic milling cutter with a segmented cutting edge showed better wear resistance and a more stable machined surface quality. It was not until a large area of coating shedding occurred, along with chip clogging, that the surface quality decreased significantly. At the stage of coating wear, the helical staggered milling cutter with an alternately arranged continuous cutting edge showed better machined surface quality, but when the coating fell off, its machined surface quality began to reveal damage such as groove, tear, and fiber pullout. Meanwhile, burrs occurred at the edge and the cutting force obviously increased. By contrast, for the rhombic milling cutter, both the surface roughness and cutting force increased relatively slowly.

Sign in / Sign up

Export Citation Format

Share Document