Tensile Strength of Sisal/Epoxy Composites Prepared by Vacuum Infusion

2018 ◽  
Vol 911 ◽  
pp. 95-99
Author(s):  
Petr Valášek

Composite systems are materials that due to its characteristics and its achievement of synergistic effects are increasingly applied. The most frequent composites are composites mainly with long fibers. In the interaction with the polymer matrix can be used inorganic fibers, but recently there is a substitution of these fibers with organic fibers. The main advantage of using organic fibers is their low cost, low weight, and availability. The benefits can also cite environmental aspects. The disadvantage is the very nature of the organic material. The paper describes a long-fiber composite system prepared by vacuum infusion and compares the tensile strength of composites with randomly oriented and arranged sisal fibers, depending on the flow direction of the resin during vacuum infusion. Composite systems were cut from boards made by vacuum infusion using a water jet. These boards are widely used by industries such as automotive or building to where the natural fibers can create design function. The use of natural fibers in this process is inexpensive and such materials can be referenced as biocomposites, saving the primary raw material. The paper describes the tensile strength and hardness. Electron microscopy was used to evaluate fracture surfaces and the morphology of the fibers.

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Atin Sumihartati ◽  
Wiah Wardiningsih ◽  
Naelly Al Kautsar ◽  
Muhammad Permana ◽  
Samuel Pradana ◽  
...  

Purpose The purpose of this study is to explore the potential of Cordyline Australis fibers as an alternate raw material for textile. Design/methodology/approach The water retting method was used to extract the fiber. Cordyline Australis fibers were characterized in terms of the morphology of fibers (fiber cross-sectional and longitudinal), fiber chemical functional groups, tensile strength and elongation, fineness, fiber length, moisture regain and friction coefficient. Findings Cordyline Australis fiber strands consist of several individual fibers. At the longitudinal section, the fiber cells appeared as long cylindrical tubes with a rough surface. The cross-section of the Cordyline Australis fibers was irregular but some were oval. The key components in the fibers were cellulose, hemicellulose and lignin. The tensile strength of the fiber per bundle was 2.5 gf/den. The elongation of fibers was 13.15%. The fineness of fiber was 8.35 Tex. The average length of the fibers was 54.72 cm. Moisture Regain for fiber was 8.59%. The friction coefficient of fibers was 0.16. The properties of the fiber showed that the Cordyline Australis fiber has the potential to be produced into yarn. Originality/value To the best of the author's knowledge, there is no scientific article focused on the Cordyline Australis fibers. Natural fibers from the leaves of the Cordyline Australis plant could be used as an alternate material for textile.


2013 ◽  
Vol 718-720 ◽  
pp. 63-68 ◽  
Author(s):  
Raja R. Niranjan ◽  
S. Junaid Kokan ◽  
R. Sathya Narayanan ◽  
S. Rajesh ◽  
V.M. Manickavasagam ◽  
...  

The natural fibre composite materials are nowadays playing a vital role in replacing the conventional and synthetic materials for industrial applications. This paper proposes a natural fiber composite made of Abaca fibre as reinforcing agent with Epoxy resin as the matrix, manufactured using Hand Lay-up method. Glass Fiber Reinforced Plastics (woven rovings) are used to improve the surface finish and impart more strength and stiffness to natural fibers. In this work, the fibers are arranged in alternative layers of abaca in horizontal and vertical orientation. The mechanical properties of the composite are determined by testing the samples for tensile and flexural strength. It is observed that the tensile strength of the composite material is dependent on the strength of the natural fiber and also on the interfacial adhesion between the reinforcement and the matrix. The composite is developed for automobile dashboard/mudguard application. It may also be extended to biomedical, electronics and sports goods manufacturing. It can also be used in marine products due to excellent resistance of abaca to salt water damage since the tensile strength when it is wet.


2016 ◽  
Vol 869 ◽  
pp. 249-254
Author(s):  
Lazaro Araújo Rohen ◽  
Anna Carolina Cerqueira Neves ◽  
Frederico Muylaert Margem ◽  
Carlos Maurício Fontes Vieira ◽  
Fabio de Oliveira Braga ◽  
...  

The use of natural fibers as reinforcement in polymer matrix composites is replacing the use of synthetic fibers, especially from an environmental standpoint. Indeed, natural fibers are biodegradable and renewable, with no aggression to the environment. Moreover, they are worldwide abundant with relatively low cost. It was found that fine fibers of sisal, with the thinnest diameters can achieve tensile strength on the order of 1000 MPa. In this work, tensile specimens were prepared with 30% in volume of sisal fibers with diameters between 0.1 and 0.10mm incorporated in a continuous and aligned way into epoxy matrix. The results showed a significant increase in tensile strength and elastic modulus of the composites as a function of the incorporated amount of thinner sisal fibers.


2021 ◽  
Vol 7 (1) ◽  
pp. 085-090
Author(s):  
Sujita Darmo Darmo ◽  
Rudy Sutanto Sutanto

Fibrous composite materials continue to be researched and developed with the long-term goal of becoming an alternative to metal substitutes. Due to the nature of the fiber reinforced composite material, its high tensile strength, and low density compared to metal. In general, the composition of the composite consists of reinforcing fibers and a matrix as the binding material. The potential of natural fibers as a reinforcing composite material is still being developed and investigated. The research that has been done aims to determine the characteristics of the tensile strength of the composite strengthened with Hibiscus tiliaceust bark powder (HTBP) with alkaline NaOH and KOH treatment. The reinforcing material used is HTBP and the matrix is polyester resin, with volume fraction of 5%, 10% and 20% with an alkaline treatment of 5% NaOH and 5% KOH with immersion for 2 hours, 4 hours, 6 hours and 8 hours. Tensile testing specimens and procedures refer to ASTM D3039 standard. The results of this study showed the highest tensile strength of 34.96 MPa in the alkaline treatment of 5% KOH, soaking time of 8 hours with a volume fraction of 10% and the lowest tensile strength of 21.96 MPa of 5% KOH alkaline treatment, soaking time of 6 hours with a volume fraction of 20%. .with 10% volume fraction of 34.96 MPa and the lowest tensile strength was 5% KOH alkaline treatment at 6 hours immersion with 20% volume fraction.


2021 ◽  
Vol 4 ◽  
pp. 146-150
Author(s):  
Arthur Y. Leiwakabessy ◽  
Benjamin G. Tentua ◽  
Fany Laamena

Durian rind fiber composite as a reinforcement is one of the interesting research areas. Some of the advantages associated with using natural fibers due to reinforcement in polymers are their non-abrasive properties and low-cost consumption. Durian rind when processed further can be made into cellulose fiber which can be used as a natural filler in unsaturated polyester composites. Among various types of natural fibers, durian skin fiber is an alternative polymer composite filler. Durian skin can be obtained easily because it is a family waste that has not been used. To get a new composite material made from durian skin waste, and to help the community and government in handling durian skin waste. The purpose of this study was to determine the maximum value of the variation of the volume fraction of durian skin fiber on the impact strength and hardness strength according to the desired application. This study uses the Hand Lay Up method, in the manufacture of single fiber composites with variations in volume fraction of durian skin fiber: polyester matrix, namely, 10%: 90%, 20%: 80%, 30%: 70%, 40%: 60% and 50 %:50%. The results showed that there was an increase in the impact strength and hardness strength with the addition of the volume fraction, where the highest impact energy for the volume fraction of durian skin fiber was 50%: 50%, 0.7738 J, and the highest impact value was 0.0096725 J/mm² and energy the lowest impact is 10%: 90%, 0.461 J. and the lowest impact price is 0.0057685 J/mm². So it can be concluded that the impact strength and hardness of the durian skin fiber composite increased with the increase in the volume fraction of the fiber.


2020 ◽  
Vol 10 (2) ◽  
pp. 37-42
Author(s):  
Irwan Suriaman ◽  
Mardiyati ◽  
Jooned Hendrarsakti ◽  
Ari Darmawan Pasek

Industry 4.0 era materials used by entrepreneurs should be recycled, environmentally friendly, renewable with less chemical content. Indonesia as a tropical country has a large land area with the potential to produce the largest natural fiber in the world. One opportunity that can be applied to the utilization of natural fibers in air filters that currently use dominant materials is synthetic fibers. natural fiber has the advantage because it does not contain toxic chemicals, local raw materials, and is easily produced. This research will analyze the mechanical and morphological characteristics of biological fibers that have great potential as pre-filter raw material. Analysis of mechanical properties through tensile strength testing for single fibers and morphological analysis through scanning electron microscopy (SEM). Tensile testing was the results are; palm oil has a tensile strength of 620 MPa; 998 MPa and 213 MPa flax coconut fiber. For the morphological test results from SEM analysis for ramie fiber, it looks solid without fiber holes; The fibers appear to be many small fibers bound to one another while coir fibers have many pore holes in one observed fiber.


2019 ◽  
Vol 7 (2) ◽  
pp. 207-220 ◽  
Author(s):  
Lisa Oktavia Br Napitupulu ◽  
Asri Widyasanti ◽  
Ahmad Thoriq ◽  
Asep Yusuf

Sansevieria or known as tongue-in-law plant is an ornamental plant that is quite popular in Indonesia. This plant is very easily cultivated, easy to grow in areas with less water and sunlight. This plant contains potential natural fibers used as raw material requirements for textile industry, specifically in fabric making. The aims of this research were to determine the production process consisting and analyzing the characteristics of woven fabrics from the leaves of the tongue-in-law plant. The method of fibers extraction used the mechanical decortication process and making woven fabric is done using ATBM. The research method used is descriptive method. Based on the results of the study, it is known that the woven cloth of tongue-in-law has color characteristics with a value of L* 69.73; a* 1.86; b* 17,38; H 83,88. Besides that, it is known the mechanical characteristics of the tongue-in-law woven fabric, the tensile strength of the fabric, the weft  direction of 46.05 kg and the warp direction of 19.96 kg; weft direction stretch 22% and stretch direction of the warp of 55.20%; weft direction tear strength 19.17% and wrap direction 4.60%; and air penetrating power 116.2 cm3/cm2/s.The value of the tensile strength of the tongue-in-law woven fabric produced in the warp direction does not meet the standards of SNI 08-0056-2006 woven fabric quality requirements for suit.Therefore, woven fabric produced is intended as a craft material.


2015 ◽  
Vol 1115 ◽  
pp. 349-352 ◽  
Author(s):  
Md. Masudur R. Abir ◽  
S.M. Kashif ◽  
Md. Abdur Razzak

To achieve sustainability in the composite industry, natural fibers must be able to replace synthetic fibers .In this work the tensile properties of sisal fibers were determined. The relationships between tensile strength, young modulus, failure to strain and gage length was studied. Also variation in tensile strength was quantified using statistical analysis. The relationship between Weibull statistics and gage length were also investigated. The strength of the sisal fiber obtained in this work was between 255-377 MPA and decreased with an increase in gage length. The Weibull modulus obtained was similar for all gage lengths and was around 2.5.


2014 ◽  
Vol 592-594 ◽  
pp. 1195-1199
Author(s):  
Ashwin Sailesh ◽  
C. Shanjeevi ◽  
J.Jeswin Arputhabalan

The developments in the field of composite materials are growing tremendously day by day. One such development is the use of natural fibers as reinforcement in the composite material. This is attributed to the fact that natural fibers are environmental friendly, economical, easily available and non-abrasive. Mixing of natural fiber with Glass Fibers is finding increased applications. In this present investigation Banana – Bamboo – Glass fiber reinforced natural fiber composites is fabricated by Hand – Layup technique with varying fiber orientation such as [0°G, 90°BM, 0°BN, 0°G], [0°G, 0°BM, +45°BN, 0°G] and [0°G, 0°BM, 90°BN, 0°G] and are tested for its tensile strength. The tensile strength of the fabricated composites is evaluated. The results indicated that the natural fiber composite with the fiber orientation of [0°G, 0°BM, 90°BN, 0°G] can withstand more load when compared to the samples with other fiber orientation. Nomenclature Used: BN – Banana fiber BM – Bamboo fiber G – Glass fiber


2016 ◽  
Vol 36 (1) ◽  
pp. 87-95
Author(s):  
U Shehu ◽  
MT Isa ◽  
BO Aderemi ◽  
TK Bello

In order to improve properties of natural fibers as reinforcement, different treatment methods have being adopted by researchers. However, the use of sodium hydroxide (NaOH) for the treatment of baobab pod fiber as reinforcement in low density polyethylene is sparsely reported. Therefore, this study, investigated the effect of 2 wt%, 4 wt% 6 wt%, 8 wt% and 10 wt%  concentration of NaOH on baobab pod fibers as reinforcement for low density polyethylene (LDPE). Two roll mill machine and hydraulic press at a pressure of 10 kN and temperature of 120oC aided the production of the composite. FT-IR was used to analyze the functional groups of the treated and un-treated fibers. The result showed the disappearance of the peak 1550 cm-1 corresponding to lignin after modification. Further, the composites were characterized for the following tensile strength (TS), modulus of elasticity (MOE), elongation at break, impact strength and water absorption. Preliminary studies on the effect of loading of the unmodified baobab fiber in the LDPE matrix showed desirable properties at 10 wt%, where fiber content was in the range of 5 wt% to 30 wt% at interval of 5 wt%. The composite produced from the 8 wt% NaOH modified fiber had the highest tensile strength, MOE, elongation at break. At this modification level, the tensile strength, MOE and elongation at break were about 75.48%, 92.18% and 28% respectively higher than the composite produced from unmodified fiber. Composite produced with 10 wt% NaOH modified fiber exhibited least water absorption of 1.80%, which was 50% lower than unmodified. These showed that the modification of the fiber improved the composite properties. These properties compared favorably with some reported properties for natural fiber reinforced polymer composites. http://dx.doi.org/10.4314/njt.v36i1.12


Sign in / Sign up

Export Citation Format

Share Document